Effect of Constrained Groove Pressing on Mechanical Properties of Nitinol Alloy

2018 ◽  
Author(s):  
S. K. Padisala ◽  
A. Bhardwaj ◽  
K. Poluri ◽  
A. K. Gupta
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Severe Plastic Deformation ◽  
Shape Memory ◽  
High Strength ◽  
Micro Hardness ◽  
Nitinol Alloy

Nitinol shape memory alloy is well known for its shape memory effect and super elastic effect. In the present work, the improvement of mechanical properties of nitinol alloy like yield strength, ultimate tensile strength and micro-hardness is discussed along with the study of evolution of micro-structure after every pass to extend the applications of shape memory alloys into high strength application areas. Severe plastic deformation processes are usually adopted for producing fine grain structures which improve the mechanical properties of a material. One such severe deformation process is constrained groove pressing, which is considered as one of the best severe plastic deformation techniques for sheet metals. The results of constrained groove pressing process on nitinol alloy show that the yield strength and the ultimate tensile strength have increased by about 3.6 times 2.5 times respectively, with an increment of 50% and 74% in micro-hardness after 1st pass of constrained groove pressing and 2nd pass of constrained groove pressing respectively. Microstructure shows increase in martensitic phase after constrained groove pressing processing. Increasing in twinning and grain boundary density can be observed in constrained groove pressing processed nitinol, which are the reasons for the tremendous increase in the strength of the alloy. Thus, the constrained groove pressing process on nitinol alloy can increase its range of application for high strength requirements.

scholarly journals Effect of Heat Treatment on Mechanical Properties and Microstructure Morphology of Low-Alloy High-Strength Steel

2016 ◽  
Vol 61 (2) ◽  
pp. 475-480
Author(s):  
K. Bolanowski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Strengthening Phase ◽  
Average Grain Size

Abstract The paper analyzes the influence of different heat treatment processes on the mechanical properties of low-alloy high-strength steel denoted by Polish Standard (PN) as 10MnVNb6. One of the findings is that, after aging, the mechanical properties of rolled steel are high: the yield strength may reach > 600 MPa, and the ultimate tensile strength is > 700 MPa. These properties are largely dependent on the grain size and dispersion of the strengthening phase in the ferrite matrix. Aging applied after hot rolling contributes to a considerable rise in the yield strength and ultimate tensile strength. The process of normalization causes a decrease in the average grain size and coalescence (reduction of dispersion) of the strengthening phase. When 10MnVNb6 steel was aged after normalization, there was not a complete recovery in its strength properties.

Mechanical Characterization of Aluminium Alloy 6061 Powder Deposit Made by Friction Stir Based Additive Manufacturing

2020 ◽  
Vol 846 ◽  
pp. 110-116
Author(s):  
Akash Mukhopadhyay ◽  
Probir Saha
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Functionally Graded ◽  
Future Application ◽  
Micro Hardness ◽  
Friction Stir ◽  
Graded Structures

Additive Friction Stir (AFS) has the potential for extensive future application in metal based additive manufacturing. Powder based AFS is specifically useful for fabricating functionally graded structures. But, the consolidation of powder inside the hollow tool used in this operation hinders the powder based AFS process. This problem could be resolved by Additive Friction Stir Processing (AFSP) while maintaining the key advantages of AFS. A 3D deposit structure of height 5 mm and width 64 mm was made from Al6061 alloy powder by AFSP. Mechanical properties like ultimate tensile strength, yield strength and micro-hardness of the deposit were evaluated in both longitudinal and transverse directions. The ultimate tensile strength and micro-hardness of the deposit were comparable to Al6061-O and there was a significant increment in tensile yield strength. Also, the isotropic nature of the deposit could be inferred from similar mechanical properties in the longitudinal and transverse direction. Dimple ruptures seen in fractographic analysis gave evidence to the ductile nature of the deposit.

Mechanical Properties and Microstructures of A356 Alloy Prepared by Casting Combined With Forging

2017 ◽  
Author(s):  
Zhenglong Liang ◽  
Qi Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
A356 Alloy ◽  
Optical Microscope ◽  
Micro Hardness ◽  
Forging Process ◽  
Scanning Electron

A novel process which combines casting with forging during one process was proposed to improve mechanical properties and refine microstructure. The microstructure evolution of as-cast samples and forged samples were analyzed by optical microscope and scanning electron microscope (SEM). The tensile properties and micro-hardness were also measured. The results show that combination of casting and forging can improve microstructure and decrease porosity of casting samples, consequently contributing to a better fatigue performance. The ultimate tensile strength and elongation were increased after forging process, however, the yield strength and micro-hardness decreased.

Fatigue of Ultra-Fine Grained α-Brass

2014 ◽  
Vol 891-892 ◽  
pp. 1125-1130
Author(s):  
Yoshikazu Nakai ◽  
Takuto Imanaka ◽  
Daiki Shiozawa
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Severe Plastic Deformation ◽  
Fatigue Limit ◽  
High Strength ◽  
Angular Pressing ◽  
Fine Grain ◽  
Proof Strength

Combined methods to obtain ultra-fine grain (UFG) α-brass samples are proposed. Severe plastic deformation followed by recrystallization was conducted, where multiple rolling and equal channel angular pressing (ECAP) were employed. Recrystallization was accomplished by heat-treatment after the severe plastic deformation, and the grain size after the severe plastic deformation was decreased. By multiple rolling, plates with thickness of 0.1 mm and grain size of 1.0 μm were obtained. By ECAP process, square bar with cross-section of 6 mm × 6 mm and minimum grain size of 4.1 μm was obtained. The 0.2 % proof strength, ultimate tensile strength, and fatigue limit were increased with the value of inverse square root of grain size (Hall-Petch relationship). Then, the 0.2 % proof strength of UFG brass was tenfold, the ultimate tensile strength and the fatigue limit were two fold increases from the conventional α-brass. Because of the high strength, the scatter of fatigue strength of UFG brass was large, which reflects the sensitivity to defects in material.

Prediction of the Ultimate Tensile Strength in API X70 Line Pipe Steel Using an Artificial Neural Network Model

2019 ◽  
Vol 297 ◽  
pp. 71-81
Author(s):  
Adel Saoudi ◽  
Djahida Lerari ◽  
Farida Khamouli ◽  
L'Hadi Atoui ◽  
Khaldoun Bachari
Keyword(s):  
Neural Network ◽  
Mechanical Properties ◽  
Artificial Neural Network ◽  
Tensile Strength ◽  
Chemical Composition ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength ◽  
Ann Model ◽  
Mean Relative Error

An artificial neural network (ANN) model has been developed for the analysis and simulation of the correlation between the chemical composition and mechanical properties of high strength low alloy (HSLA) steel X70. The input parameters of the model consist of the base metal chemical composition (C, Si, Mn, the sum of Cr+Cu+Ni+Mo, the sum of Nb+Ti+V, carbon equivalent CEpcm) and the yield strength (YS). The outputs of the ANN model include the ultimate tensile strength (UTS) of the test material. Scatter plots, correlation coefficient (R) and mean relative error (MRE) were used to assess the performance of the developed neural network. Interestingly, the model output is efficient to calculate the mechanical properties of high strength low alloy steels, especially the ultimate tensile strength as a function of chemical composition and yield strength of the used material. The obtained results are in a good agreement with experimental ones, with high correlation coefficient and low mean relative error. The predictions accuracy of the developed model also conforms to the results of mean paired T-test.

scholarly journals Effects of Substitution of Y with Yb and Ce on the Microstructures and Mechanical Properties of Mg88.5Zn5Y6.5

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 31
Author(s):  
Hongxin Liao ◽  
Taekyung Lee ◽  
Jiangfeng Song ◽  
Jonghyun Kim ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Creep Resistance ◽  
Room Temperature ◽  
High Thermal Stability ◽  
Long Period ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg88.5Zn5Y6.5-XREX (RE = Yb and Ce, X = 0, 1.5, 3.0, and 4.5) (wt.%) alloys were investigated in the present study. Mg88.5Zn5Y6.5 is composed of three phases, namely, α-Mg, long-period stacking ordered (LPSO) phases, and intermetallic compounds. The content of the LPSO phases decreased with the addition of Ce and Yb, and no LPSO phases were detected in Mg88.5Zn5Y2.0Yb4.5. The alloys containing the LPSO phases possessed a stratified microstructure and exhibited excellent mechanical properties. Mg88.5Zn5Y5.0Ce1.5 exhibited the highest creep resistance and mechanical strength at both room temperature and 200 °C, owing to its suitable microstructure and high thermal stability. The yield strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature was 358 MPa. The ultimate tensile strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature and 200 °C was 453 MPa and 360 MPa, respectively.

scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

scholarly journals PENGARUH PERSENTASE REDUKSI WARM ROLLING TERHADAP SIFAT MEKANIK PADUAN Cu-Zn 70/30

2016 ◽  
Vol 16 (1) ◽  
Author(s):  
Ayu Rizeki Ridhowati ◽  
Eka Febriyanti ◽  
Rini Riastuti
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Warm Rolling ◽  
Holding Time ◽  
Partial Recrystallization ◽  
Homogenization Process ◽  
Thermomechanical Method

Warm rolling is one of the thermomechanical method has several advantages such as produces high mechanical properties, but does not decrease % elongation and toughness value because partial recrystallization phenomenon that produces micron-sized new grain. This paper reports the results of an investigation carried out on the effects of holding time annealing to mechanical properties Cu-Zn 70/30 alloy. These alloy after homogenization process and quenched in the air then heated to temperature of 300°C, later the heated copper samples are warm rolled at 25%, 30%, and 35% reduction, after that heated at temperature 300°C and held during 120 minutes. Then sample is experienced rewarm rolling with reduction 25%, 30%, and 35%. The results obtained showed that the ultimate tensile strength and yield strength are higher proportional with the increasing of % reduction, their values are 501,1 MPa; 599,3 MPa; later decrease to 546, 5 MPa and to yield strength are 441,8 MPa; 466,1 MPa; then decrease to 458,6 MPa. Moreover hardness value increase proportional with % reduction such as 154 HV; 162 HV; after that decrease to 160 HV While, % elongation decreases inversely proportional with % reduction namely 12,4%; 8,2%; later increase to 11,2 %. It is caused of the partial recrystallization phenomenon as evidenced by the presence micron-sized.AbstrakWarm rolling merupakan salah satu metode termomekanik yang mempunyai beberapa keuntungan yaitu salah satunya menghasilkan sifat mekanik yang tinggi, namun tidak mengurunkan nilai keuletan karena adanya fenomena rekristalisasi parsial yang menghasilkan butiran baru berbentuk micron. Paper ini menjelaskan tentang hasil penelitian berupa pengaruh persentase reduksi terhadap sifat mekanis paduan Cu-Zn 70/30. Paduan Cu-Zn 70/30 setelah dilakukan proses homogenisasi dan didinginkan di udara lalu dipanaskan ke suhu 300°C, kemudian masing-masing dilakukan warm rolling dengan persentase reduksi sebesar 25%, 30%, dan 35% kemudian ditahan di suhu 300°C dalam waktu 120 menit. Selanjutnya sampel dilakukan rewarm rolling dengan persentase reduksi sebesar 25%, 30%, dan 35%. Hasil penelitian yang dilakukan antara lain nilai kekuatan tarik (UTS dan YS) yang semakin tinggi sebanding dengan peningkatan % reduksi warm rolling yaitu masing-masing untuk nilai UTS sebesar 501,1 MPa; 599,3 MPa; lalu menurun menjadi 546,5 MPa serta untuk nilai kekuatan luluh sebesar 441,8 MPa; 466,1 MPa; lalu menurun menjadi 458,6 MPa. Selain itu, nilai kekerasan meningkat sebanding dengan peningkatan % reduksi warm rolling masing-masing sebesar 154 HV; 162 HV; lalu menurun menjadi 160 HV. Sedangkan persentase elongasi semakin menurun berbanding terbalik dengan peningkatan % reduksi masing-masing sebesar 12,4%; 8,2%; lalu meningkat menjadi 11,2%. Hal tersebut disebabkan karena adanya fenomena rekristalisasi parsial yang dibuktikan dengan kehadiran butir kecil berukuran mikron.Keywords : Cu-Zn 70/30 alloy, warm rolling, anneal, % reduction, mechanical properties

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

Severe Plastic Deformation-Key Features, Methods and Application

2020 ◽  
Vol 1003 ◽  
pp. 31-36
Author(s):  
Marko Vilotic ◽  
Li Hui Lang ◽  
Sergei Alexandrov ◽  
Dragisa Vilotic
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Tensile Strength ◽  
Severe Plastic Deformation ◽  
Metal Forming ◽  
Good Corrosion Resistance ◽  
Processed Material ◽  
Key Features ◽  
Forming Methods

Compared to conventional metal forming methods, processing by severe plastic deformation is mostly used to improve the mechanical properties and not for the shaping of a product. Processed material usually has an average crystal grain size of less than a micron and as a result, the material exhibits improvements in most of the mechanical properties, such as yield and ultimate tensile strength, microhardness, sufficiently high workability, good corrosion resistance, and implant biocompatibility and others. In this paper, a brief review of the processing by severe plastic deformation was presented, including the benefits, major methods, and the application. Additionally, a brief review of two methods made by authors was made.

Sign in / Sign up

Export Citation Format

Share Document