Manufacturing of LSAW Pipes Using Hot Rolled Sheets for Sour-Service Application

2021 ◽  
Author(s):  
Rajesh Kumar Goyal ◽  
Mahesh Gajjar ◽  
Ashok Joshi ◽  
Anupkumar Tamhane
Keyword(s):  
Steel Mill ◽  
Corrosion Resistant ◽  
Behavioural Changes ◽  
H2s Corrosion ◽  
Before And After ◽  
Service Application ◽  
Hot Rolled ◽  
Sour Service ◽  
Geographical Locations ◽  
Selection Of

Abstract The exploration and transportation of fluids from corrosive fields or reserves demand corrosion-resistant pipelines. The pipelines for sour-service application demand higher resistance to H2S corrosion because of higher sulphur content observed in the geographical locations. The pipelines laid in the corrosive and marshy lands demand high wall thickness to allow for wall thinning due to corrosion. The linepipes manufactured using TMCP plates are widely accepted for sour-service applications. The use of cut-to-length sheets from hot rolled coils for the manufacturing of LSAW pipes is economical but having limited acceptance by the pipeline operators. Welspun took an initiative to develop the linepipes for an onshore sour-service application using API 5L X60MS grade cut-to-length sheets from TMCP hot rolled coils procured from an approved steel mill. The LSAW pipes of 24” OD × 14.27 mm WT were manufactured by the JCO-E press at Welspun Pipes Mill in Anjar-Gujarat-India. The experience of 24”OD × 14.30 mm WT, API 5L X60MO grade pipes manufacturing using TMCP plates procured from another approved steel mill, was used to decide factors such as alloy design, cleanliness, strength, DWTT, hardness, HIC, SSCC, CVN for the selection of cut-to-length sheets. This paper deals with sheet-to-pipe behavioural changes in properties before and after cold mechanical expansion. Wherever possible, the comparison was also made with plate-pipe behavioural changes in properties.

Sour Resistant High Strength Seamless Pipes for Risers

2013 ◽  
Author(s):  
Matteo Ortolani ◽  
Ettore Anelli ◽  
Paolo Novelli ◽  
Emanuele Paravicini Bagliani
Keyword(s):  
Heat Treatment ◽  
Mechanical Testing ◽  
High Strength ◽  
Post Weld Heat Treatment ◽  
Water Quenching ◽  
Potential Solution ◽  
Steel Pipes ◽  
Before And After ◽  
Hot Rolled ◽  
Sour Service

In case of a Weld On Connector’s riser using ASTM A182 F22 forged joints, high strength (SMYS of 80 ksi) steel pipes for sour service (hardness below or equal to 250 HV10) suitable for welding to the connectors are required. Welding is challenging because of the Post Weld Heat Treatment (PWHT) needed to reduce the hardness in the F22 HAZ while maintaining the required strength in the pipe. Theoretical evaluations were performed by means of metallurgical models and a potential solution was identified in grade P22-like steel (2¼ Cr - 1 Mo), with minor modifications with respect to the standard ASTM A335 and supplied in Q&T condition. A trial heat was cast and hot-rolled into pipes. After water quenching, the response to tempering was assessed by means of laboratory heat treatments and subsequent mechanical testing, together with metallurgical examination. Simulated PWHTs were also performed on Q&T material. 80 ksi grade P22 seamless pipes were finally produced and qualification involved mechanical testing before and after simulated PWHT: SMYS of 80 ksi and HV10 ≤ 250 requirements were met. The material also exhibited excellent toughness and resistance to HIC and SSC cracking.

scholarly journals A microfluidic device enabling drug resistance analysis of leukemia cells via coupled dielectrophoretic detection and impedimetric counting

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yağmur Demircan Yalçın ◽  
Taylan Berkin Töral ◽  
Sertan Sukas ◽  
Ender Yıldırım ◽  
Özge Zorlu ◽  
...  
Keyword(s):  
Drug Resistance ◽  
K562 Cells ◽  
Leukemia Cells ◽  
Drug Resistant ◽  
Wild Type ◽  
Gene Expressions ◽  
Before And After ◽  
The Difference ◽  
Selection Of ◽  
Resistant Cells

AbstractWe report the development of a lab-on-a-chip system, that facilitates coupled dielectrophoretic detection (DEP-D) and impedimetric counting (IM-C), for investigating drug resistance in K562 and CCRF-CEM leukemia cells without (immuno) labeling. Two IM-C units were placed upstream and downstream of the DEP-D unit for enumeration, respectively, before and after the cells were treated in DEP-D unit, where the difference in cell count gave the total number of trapped cells based on their DEP characteristics. Conductivity of the running buffer was matched the conductivity of cytoplasm of wild type K562 and CCRF-CEM cells. Results showed that DEP responses of drug resistant and wild type K562 cells were statistically discriminative (at p = 0.05 level) at 200 mS/m buffer conductivity and at 8.6 MHz working frequency of DEP-D unit. For CCRF-CEM cells, conductivity and frequency values were 160 mS/m and 6.2 MHz, respectively. Our approach enabled discrimination of resistant cells in a group by setting up a threshold provided by the conductivity of running buffer. Subsequent selection of drug resistant cells can be applied to investigate variations in gene expressions and occurrence of mutations related to drug resistance.

scholarly journals Variations of microstructure and resistance to fish-scaling of a hot rolled enamel steel before and after enamel firing

2021 ◽  
Vol 11 ◽  
pp. 466-473
Author(s):  
Xueqi Huang ◽  
Zhimin Zhang ◽  
Xianghua Liu ◽  
Yang Zhao ◽  
Xiaolin Li
Keyword(s):  
Before And After ◽  
Hot Rolled

scholarly journals PENERAPAN METODE BERMAIN PERAN MAKRO TERHADAP KEMAMPUAN BERBICARA

Instruksional ◽  
2019 ◽  
Vol 1 (1) ◽  
pp. 9
Author(s):  
Nirwana Nirwana
Keyword(s):  
Statistical Analysis ◽  
Role Playing ◽  
Wilcoxon Test ◽  
Control Group ◽  
Observation Data ◽  
Group Data ◽  
Before And After ◽  
Group B ◽  
Nonparametric Statistical ◽  
Selection Of

Effect of  role playing macro methods on children's speaking ability in group B in Nurul Rohmah Bekasi. This research is motivated by the lack of ability to speak children. This is because the method used in the learning process is more likely to use conventional methods. The selection of methods to role playing macro so that children can be motivated and interested in learning and can stimulate the ability to speak children. The population in this study were all children of group B in kindergarten Nurul Rohmah while the study sample was B3 group 11 children for the experimental group and B1 group 11 children for the control group. Data collection techniques through test techniques, and observation. Data analysis techniques used were descriptive statistical analysis and nonparametric statistical analysis. Based on the results of the Wilcoxon test calculation, the calculated T value is 66 and T table 11 then the results obtained T count (66)> T table (11) H1 is accepted and Ho is rejected means that there is an effect of role playing macro  methods on children's speaking ability. Whereas the calculated Z value obtained is 2.93 and 1.645 table Z then the result of Z arithmetic (2.93)> Z table (1.645) H1 is accepted and Ho is rejected which means that there is an effect of role playing macro method on children's speaking ability. These results indicate that there is a change in the value of the child's speaking ability before and after getting learning based on the role playing macro method.

scholarly journals The effectiveness of integrating existing digital learning resources into classroom teaching – an evaluation of the learning achievement

2012 ◽  
Vol 8 (2) ◽  
pp. 150-161
Author(s):  
Svava Pétursdóttir
Keyword(s):  
Secondary Science ◽  
Learning Resources ◽  
Teacher Competence ◽  
Digital Learning ◽  
Science Classrooms ◽  
Before And After ◽  
Quasi Experimental ◽  
Digital Learning Resources ◽  
Selection Of ◽  
Better Than

This paper presents the results of an intervention study exploring the effectiveness of an implementation of a selection of digital learning resources (DLR) in lower secondary science classrooms. Eight teachers participated in a quasi-experimental intervention, teaching three different subjects with and without DLRs. The data presented are from pupil tests before and after the teaching combined with observation of lessons and interviews with both pupils and teachers. In two of the three subjects the groups using DLRs did slightly better than the comparison group. The results indicate that successful ICT based learning is just as dependent on teacher competence as the quality and features of the resources.

scholarly journals Characterization of Chicken Skin Yellowness and Exploration of Genes Involved in Skin Yellowness Deposition in Chicken

2021 ◽  
Vol 12 ◽  
Author(s):  
Jingwen Wu ◽  
Zetong Lin ◽  
Genghua Chen ◽  
Qingbin Luo ◽  
Qinghua Nie ◽  
...  
Keyword(s):  
Skin Color ◽  
Skin Pigmentation ◽  
Differentially Expressed ◽  
Economic Trait ◽  
Chicken Skin ◽  
Before And After ◽  
Skin Coloration ◽  
Insight Into ◽  
Selection Of

Skin color is an important economic trait in meat-type chickens. A uniform bright skin color can increase the sales value of chicken. Chickens with bright yellow skin are more popular in China, especially in the broiler market of South China. However, the skin color of chickens can vary because of differences in breeds, diet, health, and individual genetics. To obtain greater insight into the genetic factors associated with the process of skin pigmentation in chickens, we used a colorimeter and high-resolution skin photographs to measure and analyze the skin color of chickens. By analyzing 534 chickens of the same breed, age, and feed condition, we found that the yellowness values of the chickens varied within this population. A significant positive correlation was found between the cloacal skin yellowness values before and after slaughter, and the cloacal skin yellowness value of live chickens was positively correlated with the overall body skin yellowness value. Additionally, chicken skin yellowness exhibited low heritability, ranging from 0.07 to 0.27. Through RNA sequencing, 882 genes were found to be differentially expressed between the skin with the highest and lowest yellowness values. Some of these differentially expressed genes may play an important role in yellow pigment deposition in chicken skin, which included TLR2B, IYD, SMOC1, ALDH1A3, CYP11A1, FHL2, TECRL, ACACB, TYR, PMEL, and GPR143. In addition, we found that the expression and variations of the BCO2 gene, which is referred to as the yellow skin gene, cannot be used to estimate the skin yellowness value of chickens in this population. These data will help to further our understanding of chicken skin yellowness and might contribute to the selection of specific chicken strains with consistent skin coloration.

scholarly journals The influence of logistics of supplies on the process of modeling of combined transport systems in method

2018 ◽  
Vol 19 (6) ◽  
pp. 1087-1091
Author(s):  
Mariusz Niekurzak ◽  
Ewa Kubińska-Jabcoń
Keyword(s):  
Material Flow ◽  
Production Equipment ◽  
Transport Systems ◽  
Rolled Steel ◽  
Steel Mill ◽  
System Components ◽  
Hot Rolled ◽  
Hot Rolled Steel ◽  
Flow Simulator ◽  
And Storage

The object of the study is to strip mill hot-rolled steel mill in Huta ArcelorMittal Poland in Cracow. The paper presents a model rolling mill logistic system which incorporates the characteristic of its subsystems: the movement and storage of materials. System components are mill production equipment, transportation, storage interop and finished products. Logistic approach requires inter alia: minimizing the transition time of materials through the system, minimizing inventories to production and should have reduced energy consumption and production tools used to manufacture the final product. For the model should be the basis to formulate the logistic system of strip mill, taking into account both the technological and economical operation of the test mill. To accomplish the task of material flow simulator was used Dosimis-3.

scholarly journals KOMPETENSI PETERNAK SAPI POTONG PERANAKAN ONGOLE DALAM PEMBUATAN KOMPOS (STUDI KASUS PADA KELOMPOK TERNAK MEKAR KECAMATAN DAGANGAN KABUPATEN MADIUN)

2018 ◽  
Vol 10 (3) ◽  
pp. 1
Author(s):  
Deha Purwoko ◽  
Bekti Nur Utami
Keyword(s):  
Manufacturing Process ◽  
Research Method ◽  
Organic Content ◽  
Compost Quality ◽  
Preparation Stage ◽  
Before And After ◽  
Descriptive Approach ◽  
Quantitative Descriptive ◽  
Selection Of

This research aims to describe the level of competence of farmers in composting, and to draft extension and try out the implementation of counseling about composting in group of livestock of Mekar. The research was conducted in sub-district Dagangan of Madiun Regency. Selection of livestock group is done by purposive that is the only group of livestock that have made compost that is group of livestock of Mekar which is located in Kepet village. The research method used is case study with quantitative descriptive approach with scoring. The population is 44 people, the sample is based on the census. The results showed that: 1) the level of competence of farmers in composting is classified with the details of the competence of the preparation stage is low, the competence of the manufacturing process is low, and the competence of the storage stage is classified; and 2) drafting the extension plan based on the target and the purpose of extension so that the breeder know, understand and able to increase the C-Organic content and C / N Ratio on the compost according to the standard. Success shows the improvement of compost quality before and after counseling in accordance with the purpose of counseling.   Keywords: competence of breeder, livestock group of Mekar, draft extension, composting, extension

Sign in / Sign up

Export Citation Format

Share Document