Experimental Studies of the Actuation of Carbon Nanotube-Based Materials

2019 ◽  
Author(s):  
Sebastian Geier ◽  
Thorsten Mahrholz ◽  
Peter Wierach ◽  
Michael Sinapius
Keyword(s):  
Experimental Studies ◽  
Test Series ◽  
Strong Condition ◽  
Free Standing ◽  
Carbon Structure ◽  
Active Behavior ◽  
In Series ◽  
Specimen Orientation ◽  
Set Up ◽  
Walled Cnts

Abstract Carbon nanotubes (CNTs) show an active behavior when they are positioned within an electric field, immersed into an electrolyte and charged. Several explanations are given, ranging from nanoscopic to macroscopic effects. This paper presents experimental proven explanations of the paper actuation and results using continuous CNTs of a CNT-array. For the first test series specimens are cut off a paper manufactured of single-walled, μ-long CNTs working in series. The second test series uses specimens which are prepared of free standing multi-walled CNTs. Their CNT lengths reach macroscopic dimensions of almost 3 mm and they can be considered as connected in parallel. Both series are electromechanically tested. The paper tests reveal their strong condition-dependent microstructure. Generally, the observed effects can be explained by diffusion of ions into the flexible CNT microstructure. In contrast, the CNT-array based specimens show almost no condition dependency which can be explained by the strong carbon bonds. Due to specimen orientation and test set-up, macroscopic effects can be excluded. The found actuation can be attributed to an elongation of the carbon structure as result of ion-interaction. However, it must be assumed that there are further superimposing effects which might not be distinguished from each other down to the last detail.

scholarly journals Application of intelligent orienteering based on Internet of things

2020 ◽  
Vol 2020 (1) ◽  
Author(s):  
Donghui Zhang ◽  
Ruijie Liu
Keyword(s):  
Internet Of Things ◽  
Network Architecture ◽  
Emergency Services ◽  
Simulation Experiment ◽  
Experimental Studies ◽  
Signal Stability ◽  
Anchor Nodes ◽  
Set Up ◽  
The Relationship ◽  
The Internet Of Things

Abstract Orienteering has gradually changed from a professional sport to a civilian sport. Especially in recent years, orienteering has been widely popularized. Many colleges and universities in China have also set up this course. With the improvement of people’s living conditions, orienteering has really become a leisure sport in modern people’s life. The reduced difficulty of sports enables more people to participate, but it also exposes a series of problems. As the existing positioning technology is relatively backward, the progress in personnel tracking, emergency services, and other aspects is slow. To solve these problems, a new intelligent orienteering application system is developed based on the Internet of things. ZigBee network architecture is adopted in the system. ZigBee is the mainstream scheme in the current wireless sensor network technology, which has many advantages such as convenient carrying, low power consumption, and signal stability. Due to the complex communication environment in mobile signal, the collected information is processed by signal amplification and signal anti-interference technology. By adding anti-interference devices, video isolators and other devices, the signal is guaranteed to the maximum extent. In order to verify the actual effect of this system, through a number of experimental studies including the relationship between error and traffic radius and the relationship between coverage and the number of anchor nodes, the data shows that the scheme studied in this paper has a greater improvement in comprehensive performance than the traditional scheme, significantly improving the accuracy and coverage. Especially the coverage is close to 100% in the simulation experiment. This research has achieved good results and can be widely used in orienteering training and competition.

Monosaccharide Biosynthesis Pathways Database

Glycobiology ◽  
2021 ◽  
Author(s):  
Jaya Srivastava ◽  
P Sunthar ◽  
Petety V Balaji
Keyword(s):  
Expression Profiling ◽  
Experimental Studies ◽  
Structural Complexity ◽  
Evolutionary Relationships ◽  
Enzyme Assays ◽  
Biosynthesis Pathway ◽  
Knock Out ◽  
Set Up ◽  
Function Relationship ◽  
Natural Glycans

Abstract A distinctive feature of glycans vis-à-vis proteins and nucleic acids is its structural complexity which arises from the huge repertoire of monosaccharides, isomeric linkages and branching. A very large number of monosaccharides have so far been discovered in natural glycans. Experimentally, pathways for the biosynthesis have been characterized completely for 55 monosaccharides and partially for a few more. However, there is no single platform which provides information about monosaccharide biosynthesis pathways and associated enzymes We have gathered 572 experimentally characterized enzymes of 66 biosynthesis pathways from literature and set up a first of its kind database called the Monosaccharide Biosynthesis Pathways Database http://www.bio.iitb.ac.in/mbpd/). Annotations such as the reaction catalysed, substrate specificity, biosynthesis pathway and PubMed IDs are provided for all the enzymes in the database. Sequence homologs of the experimentally characterized enzymes found in nearly 13,000 completely sequenced genomes from Bacteria and Archaea have also been included in the database. This platform will help in the deduction of evolutionary relationships among enzymes such as aminotransferases, nucleotidyltransferases, acetyltransferases and SDR family enzymes. It can also facilitate experimental studies such as direct enzyme assays to validate putative annotations, establish structure–function relationship, expression profiling to determine the function, determine the phenotypic consequences of gene knock-out/knock-in and complementation studies.

Intelligent diagnosis and analysis of brain lymphoma based on imaging features

2021 ◽  
pp. 1-11
Author(s):  
Yipu Mao ◽  
Muliang Jiang ◽  
Fanyu Zhao ◽  
Liling Long
Keyword(s):  
Imaging Techniques ◽  
Experimental Studies ◽  
Diagnostic Value ◽  
Imaging Features ◽  
Flow Properties ◽  
Brain Lymphoma ◽  
Diagnosis And Prognosis ◽  
Primary Brain Lymphoma ◽  
Set Up ◽  
Prognosis Evaluation

Currently, DSC has been extensively studied in the diagnosis, differential diagnosis and prognosis evaluation of brain lymphoma, but it has not obtained a uniform standard. By combining DSC imaging features, this study investigated the imaging features and diagnostic value of several types of tumors such as primary brain lymphoma. At the same time, this study obtained data from brain lymphoma patients by data collection and set up different groups to conduct experimental studies to explore the correlation between IVIM-MRI perfusion parameters and DSC perfusion parameters in brain lymphoma. Through experimental research, it can be seen that the combination of two perfusion imaging techniques can more fully reflect the blood flow properties of the lesion, which is beneficial to determine the nature of the lesion.

scholarly journals Robust H∞ Control of STMDs Used in Structural Systems by Hardware in the Loop Simulation Method

Actuators ◽  
2020 ◽  
Vol 9 (3) ◽  
pp. 55
Author(s):  
Huseyin Aggumus ◽  
Rahmi Guclu
Keyword(s):  
Natural Frequencies ◽  
Experimental Studies ◽  
Mr Damper ◽  
Simulation Method ◽  
Control Element ◽  
Structural Systems ◽  
Hardware In The Loop ◽  
Building Model ◽  
Mass Damper ◽  
Set Up

This paper investigated the performance of a semi-active tuned mass damper (STMD) on a multi-degree of freedom (MDOF) building model. A magnetorheological (MR) damper was used as a control element that provided semi-activity in the STMD. The Hardware in the Loop Simulation (HILS) method was applied to mitigate the difficulty and expense of experimental studies, as well as to obtain more realistic results from numerical simulations. In the implementation of this method for the STMD, the MR damper was set up experimentally, other parts of the system were modeled as computer simulations, and studies were carried out by operating these two parts simultaneously. System performance was investigated by excitation with two different acceleration inputs produced from the natural frequencies of the MDOF building. Additionally, a robust H ∞ controller was designed to determine the voltage transmitted to the MR damper. The results showed that the HILS method could be applied successfully to STMDs used in structural systems, and robust H ∞ controls improve system responses with semi-active control applications. Moreover, the control performance of the MR damper develops with an increase in the mass of the STMD.

scholarly journals Performance improvement of the heat recovery unit with sequential type heat pipes using TiO2 nanofluid

2019 ◽  
Vol 23 (3 Part B) ◽  
pp. 1755-1764 ◽  
Author(s):  
Ahmet Ozturk ◽  
Mehmet Ozalp ◽  
Adnan Sozen ◽  
Metin Guru
Keyword(s):  
Thermal Performance ◽  
Heat Recovery ◽  
Experimental Studies ◽  
Heat Pipes ◽  
Outer Diameter ◽  
Distilled Water ◽  
Condenser Section ◽  
Recovery System ◽  
Heat Recovery System ◽  
Set Up

This paper deals with the improvement of thermal performance of the heat recovery system in air-to-air unit by using a nanofluid of TiO particles and distilled water. The 2 experimental set-up equipped with 15 copper pipes of a 1000 mm length, 10.5 mm inner diameter, and 12 mm outer diameter was used. The evaporator section consists of 450 mm of heat pipes, the condenser section is 400 mm, and the adiabatic section is 150 mm. In experimental studies, 33% of the evaporator volumes of heat pipes were filled with working fluids. Experiments were carried out at temperatures between 25?C and 90?C by using five different cooling air-flows (40, 42, 45, 61, and 84 g/s), and two different heating powers (3 kW and 6 kW) for the evaporation section, to determine heat removed from the condensation section. Trials were performed for distilled water and nanofluid respectively, and the results were compared with each other. Results revealed that a 50% recovery in the thermal performance of the heat pipe heat recovery system was achieved in the design using TiO nanofluid as the working liquid, at a heating power of 3 kW, air 2 velocity of 2.03 m/s and air-flow of 84 g/s.

Temperature Facilitated ECR-Etching for Isotropic SiC Structuring

2010 ◽  
Vol 645-648 ◽  
pp. 849-852 ◽  
Author(s):  
Florentina Niebelschütz ◽  
Thomas Stauden ◽  
Katja Tonisch ◽  
Jörg Pezoldt
Keyword(s):  
Substrate Temperature ◽  
Gas Flow ◽  
Electron Cyclotron Resonance ◽  
Three Dimensional ◽  
Etching Process ◽  
Free Standing ◽  
Working Pressure ◽  
Isotropic Etching ◽  
Set Up ◽  
Ar Gas

In order to realize complex three dimensional or free standing structures on SiC substrates, an undercut, i.e. a selective isotropic etching process of SiC, is required. This was realized using an electron cyclotron resonance etching set up with pure SF6 and a SF6/Ar gas composition at elevated substrate temperatures. Above 350°C a significant lateral etch component was observed, which rose to a value of 50-70 nm/min increasing the substrate temperature up to 570°C during the etching process. Depending on substrate temperature the etching profiles and surface roughness were studied. Based on an analysis of the influence of microwave power, working pressure, bias voltage, gas flow and gas mixture on the etching behavior a novel isotropic, high selective, residue free etch process for SiC was developed, which allows for example the fabrication of piezoelectric actuated AlGaN/GaN resonators grown on SiC substrates.

A Review of Theoretical and Experimental Research on Various Autofrettage Processes

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Rajkumar Shufen ◽  
Uday S. Dixit
Keyword(s):  
Experimental Studies ◽  
Theoretical Models ◽  
Pressure Vessels ◽  
Future Research ◽  
Spherical Vessel ◽  
Considerable Research ◽  
Wide Range ◽  
Set Up ◽  
Compressive Residual Stresses ◽  
Spherical Pressure

Autofrettage is a metal forming technique widely incorporated for strengthening the thick-walled cylindrical and spherical pressure vessels. The technique is based on the principle of initially subjecting the cylindrical or spherical vessel to partial plastic deformation and then unloading it; as a result of which compressive residual stresses are set up. On the basis of the type of the forming load, autofrettage can be classified into hydraulic, swage, explosive, thermal, and rotational. Considerable research studies have been carried out on autofrettage with a variety of theoretical models and experimental methods. This paper presents an extensive review of various types of autofrettage processes. A wide range of theoretical models and experimental studies are described. Optimization of an autofrettage process is also discussed. Based on the review, some challenging issues and key areas for future research are identified.

Theoretical and Experimental Study of the Dynamics of the Tripod-Ball Sliding Joint With Clearance

2001 ◽  
Author(s):  
Jia Xiaohong ◽  
Ji Linhong ◽  
Jin Dewen ◽  
Zhang Jichuan
Keyword(s):  
Mathematical Model ◽  
Equations Of Motion ◽  
Experimental Studies ◽  
Active System ◽  
New Concepts ◽  
Sliding Joint ◽  
New Type ◽  
Set Up ◽  
The Mathematical Model ◽  
Kane Method

Abstract Clearance is inevitable in the kinematic joints of mechanisms. In this paper the dynamic behavior of a crank-slider mechanism with clearance in its tripod-ball sliding joint is investigated theoretically and experimentally. The mathematical model of this new-type joint is established, and the new concepts of basal system and active system are put forward. Based on the mode-change criterion established in this paper, the consistent equations of motion in full-scale are derived by using Kane method. The experimental rig was set up to measure the effects of the clearance on the dynamic response. Corresponding experimental studies verify the theoretical results satisfactorily. In addition, due to the nonlinear elements in the improved mathematical model of the joint with clearance, the chaotic responses are found in numerical simulation.

Effect of Rock on Cement Sheath Integrity: Shale vs. Sandstone

2019 ◽  
Author(s):  
Ragnhild Skorpa ◽  
Benjamin Werner ◽  
Torbjørn Vrålstad
Keyword(s):  
Experimental Studies ◽  
Young Modulus ◽  
Surrounding Rock ◽  
Degradation Mechanisms ◽  
X Ray ◽  
Pressure Cycling ◽  
Cement Sheath ◽  
Set Up ◽  
Casing Pressure ◽  
Radial Cracks

Abstract It is crucial to understand cement sheath degradation mechanisms, since the cement sheath is an important well barrier element. Repeated pressure cycling is known to cause radial cracks and microannuli in the cement sheath, and the stiffness of the surrounding rock determines how much pressure the cement withstands before failure. However, experimental data on the effect of surrounding rock (shale vs. sandstone) on cement sheath integrity are scarce. In this paper we present experimental studies on how different surrounding rocks influence cement sheath integrity. We have used our unique downscaled experimental set-up to perform pressure cycling tests with both shale and sandstones, where cement sheath integrity is visualized in 3D by X-ray computer tomography (CT). The obtained results confirm that a cement sheath surrounded by a rock with a relative higher Young’s modulus can withstand higher casing pressure compared to a cement sheath surrounded by rock with relative lower Young modulus. All cracks were initially observed as small defects in the cement sheath prior to expanding to full radial cracks and propagation into the surrounding formation.

Numerical and Experimental Studies on the Development of Variable Density Nanocomposites for Structural Applications

2018 ◽  
Author(s):  
Jayaram R. Pothnis ◽  
Dinesh Kalyanasundaram ◽  
Suhasini Gururaja
Keyword(s):  
Numerical Model ◽  
Epoxy Resin ◽  
Electric Fields ◽  
Experimental Studies ◽  
Electrical Characterization ◽  
Variable Density ◽  
Transient Nature ◽  
Structural Applications ◽  
Measured Sample ◽  
Set Up

Numerical and experimental studies performed to develop nanocomposites with varying carbon nanotube (CNT) alignment density within an epoxy matrix are presented. A 3-D numerical model has been developed that looks at the behavior of CNTs in epoxy resin subjected to non-uniform electric fields by explicitly accounting for electric field coupled with fluid flow and particle motion considering the transient resin viscosity. The transient nature of resin viscosity has been incorporated into the simulation study with data related to resin viscosity variation with time and temperature generated experimentally. The response of CNTs due to the induced dielectrophoretic force was studied using the numerical model. The model facilitated the design of an optimal electrode configuration for the processing of variable density composites. A computer controlled Arduino UNO based circuitry was developed to control supply of voltage to the electrodes during sample fabrication. The circuit was then integrated with AC voltage supply units and the electrode set-up for fabricating the variable density composite samples. Low weight fractions of CNTs (0.05 wt.% and 0.1 wt.%) in epoxy resin were used for the experimental work and preliminary experimental studies were conducted. Electrical characterization results of the variable density nanocomposites indicate over 100% and 30% increase in electrical resistance measured across sample widths in 0.05 wt.% and 0.1 wt.% CNT samples, respectively. The measured sample resistance values confirmed that variation in CNT alignment density was achieved across the samples.

Sign in / Sign up

Export Citation Format

Share Document