Alumina nanoparticle flow within a channel with permeable walls

2020 ◽  
Vol 31 (04) ◽  
pp. 2050050 ◽  
Author(s):  
Tran Dinh Manh ◽  
Nguyen Dang Nam ◽  
Gihad Keyany Abdulrahman ◽  
R. Moradi ◽  
Houman Babazadeh
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Power Law ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Expansion Ratio ◽  
Hydrodynamic Characteristics ◽  
Stream Velocity ◽  
Main Stream ◽  
The Impact

The application of the nanoparticles for the heat transfer augmentation has extensively increased in the scientific and industrial applications. In this research, semi-analytic method is used to disclose the heat transmission and flow feature of the fluid with nanoparticles among the two parallel sheets. In our model, one plate is warmed with specific heat flux while fluid is streamed from another plate which extends over times. Nanoparticles of Al2O3 are applied in the main fluid to obtain nanofluid flow. To obtained viscosity coefficient and heat conductivity of the base fluid with nanoparticles, Koo–Kleinstreuer–Li (KKL) formula is applied as reliable approach. Comprehensive investigations on different factors are done to disclose the impact of important aspects such as volume fraction of the nanoparticles, main stream velocity and expansion ratio on the main thermal and hydrodynamic characteristics of the nanofluid. It was found that the rate of the Nusselt number upsurges when the velocity of main stream, volume portion of the nanoparticles and power law index is increased. However, the increasing of the expansion ratio declines the heat transfer rate in our model. Our findings disclose that heat transfer rate is directly proportional with velocity of nanofluid as index of power law equals to zero.

Ferro-nanofluid squeeze film lubrication with heat transfer

2021 ◽  
pp. 135065012110276
Author(s):  
Manimegalai Kavarthalai ◽  
Vimala Ponnuswamy
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Contact Time ◽  
Transfer Rate ◽  
Fluid Layer ◽  
Darcy Law ◽  
Squeeze Film ◽  
Mean Temperature ◽  
Special Cases ◽  
The Impact

A theoretical study of a squeezing ferro-nanofluid flow including thermal effects is carried out with application to bearings and articular cartilages. A representational geometry of the thin layer of a ferro-nanofluid squeezed between a flat rigid disk and a thin porous bed is considered. The flow behaviours and heat transfer in the fluid and porous regions are investigated. The mathematical problem is formulated based on the Neuringer–Rosensweig model for ferro-nanofluids in the fluid region including an external magnetic field, Darcy law for the porous region and Beavers–Joseph slip condition at the fluid–porous interface. The expressions for velocity, fluid film thickness, contact time, fluid flux, streamlines, pathlines, mean temperature and heat transfer rate in the fluid and porous regions are obtained by using a perturbation method. An asymptotic solution for the fluid layer thickness is also presented. The problem is also solved by a numerical method and the results by asymptotic analysis, perturbation and numerical methods are obtained assuming a constant force squeezing state and are compared. It is shown that the results obtained by all the methods agree well with each other. The effects of various parameters such as Darcy number, Beavers–Joseph constant and magnetization parameter on the flow behaviours, contact time, mean temperature and heat transfer rate are investigated. The novel results showing the impact of using ferro-nanofluids in the two applications under consideration are presented. The results under special cases are further compared with the existing results in the literature and are found to agree well.

scholarly journals Heat Transmission Reinforcers Induced by MHD Hybrid Nanoparticles for Water/Water-EG Flowing over a Cylinder

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 623
Author(s):  
Firas A. Alwawi ◽  
Mohammed Z. Swalmeh ◽  
Amjad S. Qazaq ◽  
Ruwaidiah Idris
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Liquid Velocity ◽  
Flow Characteristics ◽  
Hybrid Nanoparticles ◽  
Critical Parameters ◽  
Heat Transmission ◽  
Constant Wall Temperature

The assumptions that form our focus in this study are water or water-ethylene glycol flowing around a horizontal cylinder, containing hybrid nanoparticles, affected by a magnetic force, and under a constant wall temperature, in addition to considering free convection. The Tiwari–Das model is employed to highlight the influence of the nanoparticles volume fraction on the flow characteristics. A numerical approximate technique called the Keller box method is implemented to obtain a solution to the physical model. The effects of some critical parameters related to heat transmission are also graphically examined and analyzed. The increase in the nanoparticle volume fraction increases the heat transfer rate and liquid velocity; the strength of the magnetic field has an adverse effect on liquid velocity, heat transfer, and skin friction. We find that cobalt nanoparticles provide more efficient support for the heat transfer rate of aluminum oxide than aluminum nanoparticles.

scholarly journals Parametric analysis of the heat transfer behavior of the nano-particle ionic-liquid flow between concentric cylinders

2021 ◽  
Vol 13 (6) ◽  
pp. 168781402110240
Author(s):  
Rehan Ali Shah ◽  
Hidayat Ullah ◽  
Muhammad Sohail Khan ◽  
Aamir Khan
Keyword(s):  
Heat Transfer ◽  
Ionic Liquid ◽  
Partial Differential Equations ◽  
Differential Equations ◽  
Heat Source ◽  
Ordinary Differential Equations ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Concentric Cylinders

This paper investigates the enhanced viscous behavior and heat transfer phenomenon of an unsteady two di-mensional, incompressible ionic-nano-liquid squeezing flow between two infinite parallel concentric cylinders. To analyze heat transfer ability, three different type nanoparticles such as Copper, Aluminum [Formula: see text], and Titanium oxide [Formula: see text] of volume fraction ranging from 0.1 to 0.7 nm, are added to the ionic liquid in turns. The Brinkman model of viscosity and Maxwell-Garnets model of thermal conductivity for nano particles are adopted. Further, Heat source [Formula: see text], is applied between the concentric cylinders. The physical phenomenon is transformed into a system of partial differential equations by modified Navier-Stokes equation, Poisson equation, Nernst-Plank equation, and energy equation. The system of nonlinear partial differential equations, is converted to a system of coupled ordinary differential equations by opting suitable transformations. Solution of the system of coupled ordinary differential equations is carried out by parametric continuation (PC) and BVP4c matlab based numerical methods. Effects of squeeze number ( S), volume fraction [Formula: see text], Prandtle number (Pr), Schmidt number [Formula: see text], and heat source [Formula: see text] on nano-ionicliquid flow, ions concentration distribution, heat transfer rate and other physical quantities of interest are tabulated, graphed, and discussed. It is found that [Formula: see text] and Cu as nanosolid, show almost the same enhancement in heat transfer rate for Pr = 0.2, 0.4, 0.6.

scholarly journals 3D Magneto-Buoyancy-Thermocapillary Convection of CNT-Water Nanofluid in the Presence of a Magnetic Field

Processes ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 258 ◽  
Author(s):  
Lioua Kolsi ◽  
Salem Algarni ◽  
Hussein A. Mohammed ◽  
Walid Hassen ◽  
Emtinene Lajnef ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Flow Structure ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Numerical Study ◽  
Flow Stabilization ◽  
Magnetic Field Magnitude ◽  
The Magnetic Field

A numerical study is performed to investigate the effects of adding Carbon Nano Tube (CNT) and applying a magnetic field in two directions (vertical and horizontal) on the 3D-thermo-capillary natural convection. The cavity is differentially heated with a free upper surface. Governing equations are solved using the finite volume method. Results are presented in term of flow structure, temperature field and rate of heat transfer. In fact, results revealed that the flow structure and heat transfer rate are considerably affected by the magnitude and the direction of the magnetic field, the presence of thermocapillary forces and by increasing nanoparticles volume fraction. In opposition, the increase of the magnetic field magnitude leads to the control the flow causing flow stabilization by merging vortexes and reducing heat transfer rate.

scholarly journals Role of Rotating Cylinder toward Mixed Convection inside a Wavy Heated Cavity via Two-Phase Nanofluid Concept

Nanomaterials ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 1138 ◽  
Author(s):  
Ammar I. Alsabery ◽  
Mohammad Ghalambaz ◽  
Taher Armaghani ◽  
Ali Chamkha ◽  
Ishak Hashim ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Rotating Cylinder ◽  
Alumina Nanoparticles ◽  
Optimum Number ◽  
Two Phase ◽  
Rotation Direction

The mixed convection two-phase flow and heat transfer of nanofluids were addressed within a wavy wall enclosure containing a solid rotating cylinder. The annulus area between the cylinder and the enclosure was filled with water-alumina nanofluid. Buongiorno’s model was applied to assess the local distribution of nanoparticles in the host fluid. The governing equations for the mass conservation of nanofluid, nanoparticles, and energy conservation in the nanofluid and the rotating cylinder were carried out and converted to a non-dimensional pattern. The finite element technique was utilized for solving the equations numerically. The influence of the undulations, Richardson number, the volume fraction of nanoparticles, rotation direction, and the size of the rotating cylinder were examined on the streamlines, heat transfer rate, and the distribution of nanoparticles. The Brownian motion and thermophoresis forces induced a notable distribution of nanoparticles in the enclosure. The best heat transfer rate was observed for 3% volume fraction of alumina nanoparticles. The optimum number of undulations for the best heat transfer rate depends on the rotation direction of the cylinder. In the case of counterclockwise rotation of the cylinder, a single undulation leads to the best heat transfer rate for nanoparticles volume fraction about 3%. The increase of undulations number traps more nanoparticles near the wavy surface.

3D optimization of baffle arrangement in a multi-phase nanofluid natural convection based on numerical simulation

2019 ◽  
Vol 30 (5) ◽  
pp. 2583-2605 ◽  
Author(s):  
Mohammad Mohsen Peiravi ◽  
Javad Alinejad ◽  
D.D. Ganji ◽  
Soroush Maddah
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Target Function ◽  
Optimal Arrangement ◽  
Content Type ◽  
Multi Phase

Purpose The purpose of this study is investigating the effect of using multi-phase nanofluids, Rayleigh number and baffle arrangement simultaneously on the heat transfer rate and Predict the optimal arrangement type of baffles in the differentiation of Rayleigh number in a 3D enclosure. Design/methodology/approach Simulations were performed on the base of the L25 Taguchi orthogonal array, and each test was conducted under different height and baffle arrangement. The multi-phase thermal lattice Boltzmann based on the D3Q19 method was used for modeling fluid flow and temperature fields. Findings Streamlines, isotherms, nanofluid volume fraction distribution and Nusselt number along the wall surface for 104 < Ra < 108 have been demonstrated. Signal-to-noise ratios have been analyzed to predict optimal conditions of maximize and minimize the heat transfer rate. The results show that by choosing the appropriate height and arrangement of the baffles, the average Nusselt number can be changed by more than 57 per cent. Originality/value The value of this paper is surveying three-dimensional and two-phase simulation for nanofluid. Also using the Taguchi method for Predicting the optimal arrangement type of baffles in a multi-part enclosure. Finally statistical analysis of the results by using of two maximum and minimum target Function heat transfer rates.

The impacts of non-uniform magnetic field on free convection heat transfer of a magnetizable micropolar nanofluid

2019 ◽  
Vol 29 (10) ◽  
pp. 3685-3706
Author(s):  
Zafar Namazian ◽  
S.A.M. Mehryan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Content Type ◽  
Viscosity Parameter ◽  
Micropolar Nanofluid ◽  
Free Convection Heat

Purpose The purpose of this study is to numerically study the heat transfer of free convection of a magnetizable micropolar nanofluid inside a semicircular enclosure. Design/methodology/approach The flow domain is under simultaneous influences of two non-uniform magnetic fields generated by current carrying wires. The directions of the currents are the same. Although the geometry is symmetric, it is physically asymmetric. The impacts of key parameters, including Rayleigh number Ra = 103-106, Hartman number Ha = 0-50, vortex viscosity parameter Δ = 0-4, nanoparticles volume fraction φ = 0-0.04 and magnetic number Mnf = 0-1000, on the macro- and micro-scales flows, temperature and heat transfer rate are studied. Finding The outcomes show that dispersing of the nanoparticles in the host fluid increases the strength of macro- and micro-scale flows. When Mnf = 0, the increment of the vortex viscosity parameter increases the strength of the particles micro-rotations, while this characteristic is decreased by growing Δ for Mnf ≠ 0. The increment of Δ and Ha decreases the rate of heat transfer. The increment of Ha decreases the enhancement percentage of heat transfer rate because of dispersing nanoparticles, known as En parameter. In addition, the value of Δ has no effect on En. Moreover, the average Nusselt number Nuavg and En remain constant by increasing the magnetic number Mnf for different volume fraction values. Originality/value The authors believe that all of the results, both numerical and asymptotic, are original and have not been published elsewhere yet.

scholarly journals Mixed convective hybrid nanofluid flow in lid-driven undulated cavity: effect of MHD and Joule heating

2019 ◽  
Vol 16 (2) ◽  
pp. 109-126 ◽  
Author(s):  
Ishrat Zahan ◽  
R Nasrin ◽  
M A Alim
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Joule Heating ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Hybrid Nanoparticles ◽  
Wave Number ◽  
Hybrid Nanofluid

A numerical analysis has been conducted to show the effects of magnetohydrodynamic (MHD) and Joule heating on heat transfer phenomenon in a lid driven triangular cavity. The heat transfer fluid (HTF) has been considered as water based hybrid nanofluid composed of equal quantities of Cu and TiO2 nanoparticles. The bottom wall of the cavity is undulated in sinusoidal pattern and cooled isothermally. The left vertical wall of the cavity is heated while the inclined side is insulated. The two dimensional governing partial differential equations of heat transfer and fluid flow with appropriate boundary conditions have been solved by using Galerkin's finite element method built in COMSOL Multyphysics. The effects of Hartmann number, Joule heating, number of undulation and Richardson number on the flow structure and heat transfer characteristics have been studied in details. The values of Prandtl number and solid volume fraction of hybrid nanoparticles have been considered as fixed. Also, the code validation has been shown. The numerical results have been presented in terms of streamlines, isotherms and average Nusselt number of the hybrid nanofluid for different values of governing parameters. The comparison of heat transfer rate by using hybrid nanofluid, Cu-water nanofluid,  TiO2 -water nanofluid and clear water has been also shown. Increasing wave number from 0 to 3 enhances the heat transfer rate by 16.89%. The enhanced rate of mean Nusselt number for hybrid nanofluid is found as 4.11% compared to base fluid.

An Investigation of Thermal and Velocity Fields for a Confined Jet Over the RE Range of 1,000-24,000

2008 ◽  
Author(s):  
N. Jeffers ◽  
J. Punch ◽  
E. Walsh
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Local Heat Transfer ◽  
Local Heat ◽  
High Heat ◽  
Heat Fluxes ◽  
Hydrodynamic Characteristics ◽  
Plate Spacing ◽  
High Heat Transfer

Contemporary electronic systems currently generate high heat fluxes at component level. Impingement cooling is an effective way to generate high heat transfer coefficients in order to meet thermal constraints. This paper investigates the heat transfer and hydrodynamic characteristics of a confined impinging liquid jet with a nozzle-to-plate spacing (H/D) ratio of 0.5. A custom measurement facility was created to infer local heat transfer rates from infra-red images of a jet impinging on a 12.5μm thick stainless steel foil configured to generate uniform heat flux. Particle-Image Velocimetry (PIV) was performed in order to obtain quantitative velocity data within the jet. A series of experiments were run for Reynolds numbers (Re) in the range of 1,000–24,000 for a jet of 8 mm diameter (D). For Re &gt; 4,000, the local heat transfer rate — in terms of Nusselt number (Nu) as a function of dimensionless radius (r/D) — had a plateau section between 0 &lt; r/D &lt; 0.6 followed by a peak at r/D ∼ 1.35. For higher Re the Nu peak exceeds that of the plateau section. For Re &lt; 4,000, a plateau section exists between 0 &lt; r/D &lt; 0.4 followed by a shoulder located between 1 &lt; r/D &lt; 1.4. The PIV data for Re &gt; 4,000 showed a strong vortex in the area of the secondary peak in Nu which was not present in the lower Re range. This phenomenon — the local peaks of heat transfer rate — has been previously reported in the literature with a degree of uncertainty as to the related fluid mechanics. This paper contributes to an understanding of the fluidic phenomenon responsible for the distribution of heat transfer rate in confined jets.

Convective Heat Transfer and Pumping Power Requirement Using Nanofluid for the Flow Through Corrugated Channel

2015 ◽  
Author(s):  
Shafi Noor ◽  
M. Monjurul Ehsan ◽  
M. S. Mayeed ◽  
A. K. M. Sadrul Islam
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Heat Transfer Rate ◽  
Convective Heat ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Pumping Power ◽  
Power Requirement ◽  
Corrugated Channel ◽  
Flow Through

Convective heat transfer rate for turbulent flow using nanofluid through both plain and corrugated channel has been investigated numerically in the present study. Three different types of nanofluids namely Al2O3-water, TiO2-water and CuO-water of different volume fractions (1%, 2%, 3%, 4% and 5%), are used as the working fluid flowing through the channel. The corrugated channels have wall geometries of trapezoidal shape of different amplitude-wavelength ratios. Grid independence study was carried out for all the geometries. The obtained results in case of base fluid-water flowing through parallel plate channel have been validated with well-established correlations. The study has been conducted by finite volume method to solve the transport equation for the momentum, energy and turbulence quantities using single phase model of the nanofluids where the thermophysical properties of the nanofluids are calculated by using different correlations from the literature. In this study, the heat transfer enhancement using nanofluids compared to that using base fluid-water is presented for a range of Reynolds number- 15000 to 40000. The pumping power required for the flow through the channels increases with the increase in the viscosity of the fluid which justifies the increase in pumping power requirement in case of nanofluids compared to that with water. While using corrugation at the wall of the channels, in addition to the enhancement in the convective heat transfer rate, there is an increase in the pumping power requirement for the same Reynolds number. However, for a given requirement of heat transfer rate, the required pumping power can be reduced by using nanofluids. This study includes the trend and limit of volume fraction of nanofluid during this pumping power reduction phenomenon. The results show that with the increase in the volume fraction of the nanofluids, the convective heat transfer rate increases which is same for all the geometries of the fluid domain. Addition of nanofluid reduces the pumping power requirement for a constant heat transfer rate. The volume fraction of the nanofluids with which the maximum reduction of pumping power takes place at the optimum working condition is also found in the present study. This study draws a comparison among three different nanofluids in terms of the enhancement in the convective heat transfer rate and corresponding pumping power requirement for the flow through the trapezoidal shaped corrugated channel of various amplitude-wavelength ratios in order to find out the best nanofluids for its optimum results within a specified range of working conditions.

Sign in / Sign up

Export Citation Format

Share Document