SURFACE CHEMICAL MODIFICATION OF CIIR RUBBER BY HIGH DENSITY PLASMA TREATMENT

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2682-2687 ◽  
Author(s):  
JONG-HYOUNG KIM ◽  
NORITSUGU UMEHARA ◽  
HIROYUKI KOUSAKA ◽  
MAMORU SHIMADA ◽  
MITSURU HASEGAWA
Keyword(s):  
Surface Energy ◽  
Plasma Treatment ◽  
Treatment Time ◽  
Argon Plasma ◽  
Angle Measurements ◽  
Plasma Treatments ◽  
Treatment Conditions ◽  
Contact Angle Measurements ◽  
Effect Of Oxygen ◽  
Oxygen Functionality

This paper has reported the effect of oxygen and argon plasma treatments of CIIR rubber using Attenuated Total Reflectance (ATR) and surface energy measurements. Plasma treatment led to changes in the surface energy from 31 to 45.7 mN/m. Plasma treatment conditions influenced both the changes in surface energy and stability, and they also became more difficult to obtain good contact angle measurements. However, plasma treatments made the interfacial properties to be stabilized. ATR measurements revealed that changes in surface energy with treatment time are due mostly to increased oxygen functionality.

Effect of Oxygen Plasma Treatments on Polypropylene-Epoxy Interfacial Strength

1989 ◽  
Vol 153 ◽  
Author(s):  
E. Occhiello ◽  
M. Morra ◽  
G. Morini ◽  
F. Garbassi
Keyword(s):  
Surface Layer ◽  
Plasma Treatment ◽  
Oxygen Plasma ◽  
Interfacial Strength ◽  
Oxygen Plasma Treatment ◽  
Weak Point ◽  
Angle Measurements ◽  
Plasma Treatments ◽  
Contact Angle Measurements ◽  
Effect Of Oxygen

AbstractThe effect of oxygen plasma treatment on adhesion and surface properties of polypropylene (PP) was assessed. An oxygen rich modified PP layer, immiscible with bulk PP, was formed by the treatment. Contact angle measurements showed that macromolecular motions led with time to rearrangements of the surface layer drastically decreasing its wettability, while its composition, measured by XPS, remained unaffected.The shear strength of PP-epoxy joints increased after plasma treatment. The locus of failure was found to occur at the PP/epoxy interface for untreated PP, within PP in the case of oxygen-plasma-treated samples, close to the modified PP/bulk PP interface. This result suggests that the plasma treament improves the interaction at the PP/epoxy interface, but weakens the mechanical strength of the surface layer thereby creating a weak point at the modified PP/bulk PP interface.

Effect of Oxygen Plasma Treatments on Polypropylene-Epoxy Interfacial Strength

1989 ◽  
Vol 154 ◽  
Author(s):  
E. Occhiello ◽  
M. Morra ◽  
G. Morini ◽  
F. Garbassi
Keyword(s):  
Surface Layer ◽  
Plasma Treatment ◽  
Oxygen Plasma ◽  
Interfacial Strength ◽  
Oxygen Plasma Treatment ◽  
Weak Point ◽  
Angle Measurements ◽  
Plasma Treatments ◽  
Contact Angle Measurements ◽  
Effect Of Oxygen

AbstractThe effect of oxygen plasma treatment on adhesion and surface properties of polypropylene (PP) was assessed. An oxygen rich modified PP layer, immiscible with bulk PP, was formed by the treatment. Contact angle measurements showed that macromolecular motions led with time to rearrangements of the surface layer drastically decreasing its wettability, while its composition, measured by XPS, remained unaffected.The shear strength of PP-epoxy joints increased after plasma treatment. The locus of failure was found to occur at the PP/epoxy interface for untreated PP, within PP in the case of oxygen-plasma-treated samples, close to the modified PP/bulk PP interface. This result suggests that the plasma treament improves the interaction at the PP/epoxy interface, but weakens the mechanical strength of the surface layer thereby creating a weak point at the modified PP/bulk PP interface.

PLASMA TREATMENT OF CIIR RUBBER WITH IMPROVEMENT OF ADHESION AND REAL CONTACT AREA

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2688-2693
Author(s):  
JONG-HYOUNG KIM ◽  
ISAMI NITTA ◽  
NORITSUGU UMEHARA ◽  
HIROYUKI KOUSAKA ◽  
MAMORU SHIMADA ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Contact Area ◽  
Microwave Plasma ◽  
Treatment Time ◽  
Adhesion Force ◽  
Argon Plasma ◽  
Real Contact Area ◽  
Adhesion Forces ◽  
Real Contact ◽  
Plasma Treatments

The adhesion force between a chloride-isobutene-isoprene rubber (CIIR) and stainless steel ball was studied. To decrease the adhesion force, the CIIR rubber was treated with high-density microwave plasma employing oxygen and argon gases. The experimental results showed that the adhesion force decreases with increasing the time of oxygen and argon plasma treatments. In addition, the contact microscope measurements revealed different surface structure with two gases. The real contact area also decreased with treatment time and dramatic changes were observed after 5 min treatment of CIIR rubber. The field emission scanning electron microscope image also showed that the subsurface of CIIR rubber pattern has changed with various plasma treatments. These results imply change in the morphology of CIIR rubber surface by plasma treatment is one reason for the decrease in adhesion forces.

Surface Properties of UHMWPE Fiber after Low Temperature Argon-Plasma Treatment

2012 ◽  
Vol 499 ◽  
pp. 90-94 ◽  
Author(s):  
Jin Yun Xu ◽  
Wen Yu Wang ◽  
Xin Jin
Keyword(s):  
Molecular Weight ◽  
Low Temperature ◽  
Plasma Treatment ◽  
Treatment Time ◽  
Argon Plasma ◽  
Uhmwpe Fiber ◽  
Wetting Ability ◽  
Plasma Treatment Time ◽  
Uhmwpe Fibers ◽  
Ultra High Molecular Weight

To improve the adhesion between ultra-high-molecular-weight polyethylene (UHMWPE) fibers and matrix, the UHMWPE fibers were treated by low temperature argon-plasma. The effects of argon-plasma treatment on the properties of UHMWPE have been investigated. The roughness and wetting ability were all found to increase significantly after modifications. The tensile strength of UHMWE fibers were decreased with the plasma treatment time. The optimum plasma treatment is 2min.The increasing of roughness and wetting ability of UHMWPE fiber are beneficial to the improvement the adhesion between UHMWPE fiber and matrix.

scholarly journals Biomaterial Embedding Process for Ceramic–Polymer Microfluidic Sensors

Sensors ◽  
2020 ◽  
Vol 20 (6) ◽  
pp. 1745 ◽  
Author(s):  
Witold Nawrot ◽  
Karol Malecha
Keyword(s):  
Plasma Treatment ◽  
Anodic Bonding ◽  
Plasma Modification ◽  
Biochemical Processes ◽  
Angle Measurements ◽  
Plasma Activation ◽  
Microfluidic Sensors ◽  
Contact Angle Measurements ◽  
Novel Method ◽  
Sample Structure

One of the major issues in microfluidic biosensors is biolayer deposition. Typical manufacturing processes, such as firing of ceramics and anodic bonding of silicon and glass, involve exposure to high temperatures, which any biomaterial is very vulnerable to. Therefore, current methods are based on deposition from liquid, for example, chemical bath deposition (CBD) and electrodeposition (ED). However, such approaches are not suitable for many biomaterials. This problem was partially resolved by introduction of ceramic–polymer bonding using plasma treatment. This method introduces an approximately 15-min-long window for biomodification between plasma activation and sealing the system with a polymer cap. Unfortunately, some biochemical processes are rather slow, and this time is not sufficient for the proper attachment of a biomaterial to the surface. Therefore, a novel method, based on plasma activation after biomodification, is introduced. Crucially, the discharge occurs selectively; otherwise, it would etch the biomaterial. Difficulties in manufacturing ceramic biosensors could be overcome by selective surface modification using plasma treatment and bonding to polymer. The area of plasma modification was investigated through contact-angle measurements and Fourier-transform infrared (FTIR) analyses. A sample structure was manufactured in order to prove the concept. The results show that the method is viable.

Influence of argon plasma treatment on carbon fibre reinforced high performance thermoplastic composite

2020 ◽  
pp. 095400832095706
Author(s):  
Jennifer Vinodhini ◽  
K Sudheendra ◽  
Meera Balachandran ◽  
Shantanu Bhowmik
Keyword(s):  
Mechanical Properties ◽  
Contact Angle ◽  
Surface Energy ◽  
Carbon Fibre ◽  
Plasma Treatment ◽  
Dynamic Contact Angle ◽  
Argon Plasma ◽  
Dynamic Contact ◽  
Resin Matrix ◽  
Surface Modified

This investigation highlights argon plasma treatment on Poly-aryl-ether-ketone (PAEK) and carbon fibre (CF) surface. The PAEK and CF surface is modified for 300 sec and the change in physiochemical and mechanical properties were investigated through Fourier Transform Infrared Spectroscopy (FTIR), Dynamic Contact angle, Atomic Force Microscope (AFM) and Tensile Test. FTIR of surface modified PAEK revealed the stretching of C-H, C=C and C=O functional groups. A reversal phenomenon of increased surface energy was observed through dynamic contact angle study of CF and to further examine the surface energy effect, AFM analysis on CF was carried out revealing increased roughness with numerous micro dents formation. PAEK/CF composite samples were fabricated through compression moulding technique. The change in mechanical properties due to surface modification were analysed through Tensile testing on surface modified PAEK/CF sample and untreated PAEK/CF samples. The surface treated PAEK/CF showed increased tensile strength than untreated PAEK/CF. The argon plasma treatment helped in creating depth striations that lead to better interlocking of resin matrix with the reinforced CF. The fracture surface was examined through Filed Emission Scanning Electron Microscope (FE-SEM) wherein the Micrographs of the tensile tested samples indicated failure of composite due to fibre breakage.

scholarly journals Plasma Treatment Limits Human Melanoma Spheroid Growth and Metastasis Independent of the Ambient Gas Composition

Cancers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2570 ◽  
Author(s):  
Sybille Hasse ◽  
Tita Meder ◽  
Eric Freund ◽  
Thomas von Woedtke ◽  
Sander Bekeschus
Keyword(s):  
Plasma Treatment ◽  
Treatment Time ◽  
Argon Plasma ◽  
Ambient Air ◽  
Human Melanoma ◽  
Melanoma Metastasis ◽  
Spheroid Growth ◽  
Tumor Entity ◽  
Melanoma Treatment ◽  
Jet Plasma

Melanoma skin cancer is still a deadly disease despite recent advances in therapy. Previous studies have suggested medical plasma technology as a promising modality for melanoma treatment. However, the efficacy of plasmas operated under different ambient air conditions and the comparison of direct and indirect plasma treatments are mostly unexplored for this tumor entity. Moreover, exactly how plasma treatment affects melanoma metastasis has still not been explained. Using 3D tumor spheroid models and high-content imaging technology, we addressed these questions by utilizing one metastatic and one non-metastatic human melanoma cell line targeted with an argon plasma jet. Plasma treatment was toxic in both cell lines. Modulating the oxygen and nitrogen ambient air composition (100/0, 75/25, 50/50, 25/75, and 0/100) gave similar toxicity and reduced the spheroid growth for all conditions. This was the case for both direct and indirect treatments, with the former showing a treatment time-dependent response while the latter resulted in cytotoxicity with the longest treatment time investigated. Live-cell imaging of in-gel cultured spheroids indicated that plasma treatment did not enhance metastasis, and flow cytometry showed a significant modulation of S100A4 but not in any of the five other metastasis-related markers (β-catenin, E-cadherin, LEF1, SLUG, and ZEB1) investigated.

scholarly journals Improved de-inking of inkjet-printed paper using environmentally friendly atmospheric pressure low temperature plasma for paper recycling

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Rodolphe Mauchauffé ◽  
Seung Jun Lee ◽  
Isaac Han ◽  
Sang Hyeong Kim ◽  
Se Youn Moon
Keyword(s):  
Plasma Treatment ◽  
Atmospheric Pressure ◽  
Paper Recycling ◽  
Temperature Plasma ◽  
Water Contact ◽  
Angle Measurements ◽  
Natural Energy ◽  
Contact Angle Measurements ◽  
Speed Up ◽  
Uv Visible

Abstract Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal.

scholarly journals Bactericidal effects of non-thermal argon plasma in vitro, in biofilms and in the animal model of infected wounds

2011 ◽  
Vol 60 (1) ◽  
pp. 75-83 ◽  
Author(s):  
Svetlana A. Ermolaeva ◽  
Alexander F. Varfolomeev ◽  
Marina Yu. Chernukha ◽  
Dmitry S. Yurov ◽  
Mikhail M. Vasiliev ◽  
...  
Keyword(s):  
Staphylococcus Aureus ◽  
Plasma Treatment ◽  
Pathogenic Bacteria ◽  
Argon Plasma ◽  
Burkholderia Cenocepacia ◽  
Gram Negative Bacteria ◽  
Gram Positive ◽  
Gram Negative ◽  
Gram Positive Bacteria ◽  
Plasma Treatments

Non-thermal (low-temperature) physical plasma is under intensive study as an alternative approach to control superficial wound and skin infections when the effectiveness of chemical agents is weak due to natural pathogen or biofilm resistance. The purpose of this study was to test the individual susceptibility of pathogenic bacteria to non-thermal argon plasma and to measure the effectiveness of plasma treatments against bacteria in biofilms and on wound surfaces. Overall, Gram-negative bacteria were more susceptible to plasma treatment than Gram-positive bacteria. For the Gram-negative bacteria Pseudomonas aeruginosa, Burkholderia cenocepacia and Escherichia coli, there were no survivors among the initial 105 c.f.u. after a 5 min plasma treatment. The susceptibility of Gram-positive bacteria was species- and strain-specific. Streptococcus pyogenes was the most resistant with 17 % survival of the initial 105 c.f.u. after a 5 min plasma treatment. Staphylococcus aureus had a strain-dependent resistance with 0 and 10 % survival from 105 c.f.u. of the Sa 78 and ATCC 6538 strains, respectively. Staphylococcus epidermidis and Enterococcus faecium had medium resistance. Non-ionized argon gas was not bactericidal. Biofilms partly protected bacteria, with the efficiency of protection dependent on biofilm thickness. Bacteria in deeper biofilm layers survived better after the plasma treatment. A rat model of a superficial slash wound infected with P. aeruginosa and the plasma-sensitive Staphylococcus aureus strain Sa 78 was used to assess the efficiency of argon plasma treatment. A 10 min treatment significantly reduced bacterial loads on the wound surface. A 5-day course of daily plasma treatments eliminated P. aeruginosa from the plasma-treated animals 2 days earlier than from the control ones. A statistically significant increase in the rate of wound closure was observed in plasma-treated animals after the third day of the course. Wound healing in plasma-treated animals slowed down after the course had been completed. Overall, the results show considerable potential for non-thermal argon plasma in eliminating pathogenic bacteria from biofilms and wound surfaces.

Sign in / Sign up

Export Citation Format

Share Document