AC MAGNETIC SUSCEPTIBILITY INVESTIGATION OF THE INTERGRAIN VORTEX PINNING INVOLVING Er IONS IN BULK (Bi1.6Pb0.4)(Sr1.8Ba0.2)(Ca1-xErx)2Cu3Oy SUPERCONDUCTOR

2000 ◽  
Vol 14 (12) ◽  
pp. 447-453 ◽  
Author(s):  
A. V. POP
Keyword(s):  
Volume Fraction ◽  
Ac Susceptibility ◽  
Field Amplitude ◽  
Vortex Pinning ◽  
Ac Magnetic Susceptibility ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
Bulk System ◽  
Flux Diffusion

Bulk superconducting samples with composition ( Bi 1.6 Pb 0.4)( Sr 1.8 Ba 0.2)( Ca 1-x Er x)2 Cu 3 O y (0 ≤ x ≤ 0.02 Er ) were prepared by conventional solid-state reaction. X-ray diffraction confirmed that with increasing Er concentration, the volume fraction of 2223 phase decreases. The intergranular vortex dynamics (and the effective pinning barrier) of the bulk system have been investigated by ac susceptibility as a function of temperature, frequency and ac field amplitude. The effect of Er ion on the intergrain vortex pinning was characterized quantitatively by using a flux diffusion model in which the effective pinning barrier depends nonlinearly on the current density.

TIN ADDITION TO THE (Bi, Pb) 2223 SYSTEM

1994 ◽  
Vol 08 (19) ◽  
pp. 1175-1183 ◽  
Author(s):  
G. RAVI CHANDRA ◽  
B. GOPALA KRISHNA ◽  
S. V. SURYANARAYANA ◽  
T. S. N. MURTHY
Keyword(s):  
Heat Treatment ◽  
Magnetic Susceptibility ◽  
Electrical Resistance ◽  
Volume Fraction ◽  
Ac Magnetic Susceptibility ◽  
Superconducting Properties ◽  
X Ray Diffraction ◽  
Metallic Behavior ◽  
X Ray

The effect of the addition of Sn on the superconducting properties of the Bi 1.7 Pb 0.3 Sr 2 Ca 2 Cu 3 O y system as functions of Sn concentration and heat treatment has been studied by dc electrical resistance, ac magnetic susceptibility, and X-ray diffraction. Tin addition suppresses the volume fraction of the high T c phase. Samples with Sn > 0.1 show metallic behavior up to LNT. The formation of the Ca 2 PbO 4 phase is promoted by Sn. This depletes the amount of Pb and Ca necessary for the formation of the 2223 phase, thus reducing the volume fraction of the 2223 phase. It is possible that at least a small fraction of tin substitutes some of the cationic sites of the starting composition. The results of the different measurements are presented.

scholarly journals Superconducting Properties of Bi2-xPb0.3WxSr2Ca2Cu3O10+ Compounds

2021 ◽  
pp. 490-495
Author(s):  
Mohammed J. Tuama ◽  
Lamia K. Abbas
Keyword(s):  
Volume Fraction ◽  
Solid State Reaction Method ◽  
Lattice Parameter ◽  
Crystallographic Structure ◽  
Nominal Composition ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
Two Phases ◽  
Parameter Values

The conventional solid-state reaction method was utilized to prepare a series of superconducting samples of the nominal composition Bi2-xPb0.3WxSr2Ca2Cu3O10+d with 0≤x≤0.5 of 50 nm particle size of tungsten sintered at 8500C for 140h in air . The influence of substitution with W NPs at bismuth (Bi) sites was characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and dc electrical resistivity. Room temperature X-ray diffraction analysis revealed that there exists two phases, i.e. Bi-(2223) and Bi-(2212), in addition to the impurity phases of (SrCa) 2Cu2O3, Sr2Ca2Cu7Oδ, Ca2PbO4, CaO, and WO. It was found that the crystallographic structure of all samples was orthorhombic. Lattice parameter values and the volume fraction of the (2223)-phase of the prepared samples were also calculated. The superconductivity transition temperature (Tc) for samples subjected to substitution with W NPs was found to be higher than that for the pure sample. The optimal value of W NPs content in (Bi, Pb)-2223 system was found to be at x=0.3. 

Raman And Fluorescence Spectra Observed in Laser Microprobe Measurements of Several Compositions in the Ln-Ba-Cu-O System

1990 ◽  
Vol 48 (2) ◽  
pp. 278-279
Author(s):  
Edgar S. Etz ◽  
Thomas D. Schroeder ◽  
Winnie Wong-Ng
Keyword(s):  
Fluorescence Spectra ◽  
Single Phase ◽  
X Ray Diffraction ◽  
Ceramic Powders ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
Raman Microprobe ◽  
Methods Of Synthesis ◽  
Compositional Homogeneity ◽  
Processing Techniques

We are investigating by Raman microprobe measurements the superconducting and related phases in the LnBa2Cu3O7-x (for x=0 to 1) system where yttrium has been replaced by several of the lanthanide (Ln = Nd,Sm,Eu,Ho,Er) elements. The aim is to relate the observed optical spectra (Raman and fluorescence) to the compositional and structural properties of these solids as part of comprehensive materials characterization. The results are correlated with the methods of synthesis, the processing techniques of these materials, and their superconducting properties. Of relevance is the substitutional chemistry of these isostructural systems, the differences in the spectra, and their microanalytical usefulness for the detection of impurity phases, and the assessment of compositional homogeneity. The Raman spectra of most of these compounds are well understood from accounts in the literature.The materials examined here are mostly ceramic powders prepared by conventional solid state reaction techniques. The bulk samples are of nominally single-phase composition as determined by x-ray diffraction.

scholarly journals Synthesis and Na+ Ion Conductivity of Stoichiometric Na3Zr2Si2PO12 by Liquid-Phase Sintering with NaPO3 Glass

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3790
Author(s):  
Yongzheng Ji ◽  
Tsuyoshi Honma ◽  
Takayuki Komatsu
Keyword(s):  
Solid State ◽  
Liquid Phase ◽  
Sintering Temperature ◽  
Liquid Phase Sintering ◽  
Ion Conductivity ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
Sintering Time ◽  
Lower Activation

Sodium super ionic conductor (NASICON)-type Na3Zr2Si2PO12 (NZSP) with the advantages of the high ionic conductivity, stability and safety is one of the most famous solid-state electrolytes. NZSP, however, requires the high sintering temperature about 1200 °C and long sintering time in the conventional solid-state reaction (SSR) method. In this study, the liquid-phase sintering (LPS) method was applied to synthesize NZSP with the use of NaPO3 glass with a low glass transition temperature of 292 °C. The formation of NZSP was confirmed by X-ray diffraction analyses in the samples obtained by the LPS method for the mixture of Na2ZrSi2O7, ZrO2, and NaPO3 glass. The sample sintered at 1000 °C for 10 h exhibited a higher Na+ ion conductivity of 1.81 mS/cm at 100 °C and a lower activation energy of 0.18 eV compared with the samples prepared by the SSR method. It is proposed that a new LPE method is effective for the synthesis of NZSP and the NaPO3 glass has a great contribution to the Na+ diffusion at the grain boundaries.

scholarly journals Effect of the γ→ε Phase Transition on Transformation-Induced Plasticity (TRIP) of Nickel-Free High Nitrogen Steel at Low Temperatures

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 710
Author(s):  
Natalia Narkevich ◽  
Yevgeny Deryugin ◽  
Yury Mironov
Keyword(s):  
Volume Fraction ◽  
Tensile Load ◽  
X Ray Diffraction ◽  
High Nitrogen Steel ◽  
Transformation Induced Plasticity ◽  
X Ray ◽  
Root Cause ◽  
Nitrogen Steel ◽  
Ε Phase ◽  
Ε Martensite

The deformation behavior, mechanical properties, and microstructure of Fe-Cr-Mn-0.53%N austenitic stainless steel were studied at a temperature range of 77 up to 293 K. The dynamics of the steel elongation were non-monotonic with a maximum at 240–273 K, when peaks of both static atom displacements from their equilibrium positions in austenite and residual stresses in the tensile load direction were observed. The results of X-ray diffraction analysis confirmed that the only stress-induced γ→ε-martensite transformation occurred upon deformation (no traces of the γ→α′ one was found). In this case, the volume fraction of ε-martensite was about 2–3%. These transformation-induced plasticity (TRIP) patterns were discussed in terms of changes in the phase composition of steel as the root cause.

Effect of the BSCCO superconducting properties by tiny Y2O3 addition

2016 ◽  
Vol 30 (26) ◽  
pp. 1650328
Author(s):  
Yan Dong ◽  
Aimin Sun ◽  
Bin Xu ◽  
Hongtao Zhang ◽  
Meng Zhang
Keyword(s):  
Volume Fraction ◽  
Superconducting Properties ◽  
X Ray Diffraction ◽  
Critical Transition Temperature ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Oxide Addition ◽  
One Step ◽  
Step Transition ◽  
Y2o3 Addition

In this paper, the effect of tiny Y2O3 addition in (Bi,[Formula: see text]Pb)-2223 superconductor prepared by solid state reaction technique was studied. The properties of samples have been investigated via X-ray diffraction (XRD), resistance–temperature ([Formula: see text]–[Formula: see text]) curve, scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS). XRD data indicated that all samples are multiphase and the major phases are high-temperature phases and low-temperature phases. The volume fraction of (Bi,[Formula: see text]Pb)-2223 is not great change with tiny Y2O3 addition. All samples exhibit superconducting phase with the critical transition temperature and one-step transition, however, the transition width was decreased with the Y2O3 addition up to 0.04 wt.% and sharp increased with the excessive oxide addition. SEM pictures show that the Y2O3 appeared on the flake-type grains surface obviously, but the number and size of the hole between grains are decreased in the 0.04 wt.% addition.

Spark Plasma Sintering of Ti-4.5Al-3V-2Fe-2Mo (SP-700)

2010 ◽  
Vol 654-656 ◽  
pp. 819-822
Author(s):  
Genki Kikuchi ◽  
Hiroshi Izui ◽  
Yuya Takahashi ◽  
Shota Fujino
Keyword(s):  
Spark Plasma Sintering ◽  
Room Temperature ◽  
Volume Fraction ◽  
Titanium Boride ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Tib2 Particles

In this study, we focused on the sintering performance of Ti-4.5Al-3V-2Mo-2Fe (SP-700) and mechanical properties of SP-700 reinforced with titanium boride (TiB/SP-700) fabricated by spark plasma sintering (SPS). TiB whiskers formed in titanium by a solid-state reaction of titanium and TiB2 particles were analyzed with scanning electron microscopy and X-ray diffraction. The TiB/SP-700 was sintered at temperatures of 1073, 1173, and 1273 K and a pressure of 70 MPa for 10, 30, and 50 min. The volume fraction of TiB ranged from 1.7 vol.% to 19.9 vol.%. Tensile tests of TiB/SP-700 were conducted at room temperature, and the effect of TiB volume fraction on the tensile properties was investigated.

scholarly journals Влияние толщины пленки Pt на изменение текстуры и доли кристаллической фазы при ее отжиге

2020 ◽  
Vol 90 (5) ◽  
pp. 795
Author(s):  
Р.В. Селюков ◽  
В.В. Наумов
Keyword(s):  
Volume Fraction ◽  
Curve Analysis ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Texture Parameters ◽  
Sputter Deposited ◽  
Pt Films ◽  
H 20

Textured Pt films with thickness h=20-80 nm were sputter deposited on oxidized c-Si (100) wafers and annealed in vacuum at 500°C/60 min. The thickness dependencies of the crystalline texture parameters and of the fraction of crystalline phase δ are obtained for as-deposited and annealed films using X-ray diffraction. The determination of δ in textured films is carried out by the new method based on rocking curve analysis. It is found that annealing leads to the texture improvement and to the increasing of δ for all h. The less h, the stronger effects of texture improvement and of δ increasing. These results are explained by the annealing-induced formation of large secondary grains whose volume fraction increases as h decreases. The inhomogeneity of the depth distributions of texture parameters and of δ are investigated for the as-deposited Pt films.

scholarly journals TEM Study of High-Temperature Precipitation of Delta Phase in Inconel 718 Alloy

2011 ◽  
Vol 2011 ◽  
pp. 1-9 ◽  
Author(s):  
Moukrane Dehmas ◽  
Jacques Lacaze ◽  
Aliou Niang ◽  
Bernard Viguier
Keyword(s):  
Inconel 718 ◽  
Volume Fraction ◽  
Alloy 718 ◽  
Double Diffraction ◽  
X Ray Diffraction ◽  
Inconel 718 Alloy ◽  
X Ray ◽  
Delta Phase ◽  
Transmission Electron ◽  
Matrix Free

Inconel 718 is widely used because of its ability to retain strength at up to 650∘C for long periods of time through coherent metastable Ni3Nb precipitation associated with a smaller volume fraction of Ni3Al precipitates. At very long ageing times at service temperature, decomposes to the stable Ni3Nb phase. This latter phase is also present above the solvus and is used for grain control during forging of alloy 718. While most works available on precipitation have been performed at temperatures below the solvus, it appeared of interest to also investigate the case where phase precipitates directly from the fcc matrix free of precipitates. This was studied by X-ray diffraction and transmission electron microscopy (TEM). TEM observations confirmed the presence of rotation-ordered domains in plates, and some unexpected contrast could be explained by double diffraction due to overlapping phases.

Stress in Hydrogenated Microcrystalline Silicon Thin Films

1999 ◽  
Vol 557 ◽  
Author(s):  
D. Peiró ◽  
C. Voz ◽  
J. Bertomeu ◽  
J. Andreu ◽  
E. Martínez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Vapor Deposition ◽  
Volume Fraction ◽  
Chemical Vapor ◽  
Hot Wire ◽  
X Ray Diffraction ◽  
Microcrystalline Silicon ◽  
X Ray ◽  
Silicon Thin Films ◽  
Abrupt Changes

AbstractHydrogenated microcrystalline silicon films have been obtained by hot-wire chemical vapor deposition (HWCVD) in a silane and hydrogen mixture at low pressure (<5 × 10-2 mbar). The structure of the samples and the residual stress were characterised by X- ray diffraction (XRD). Raman spectroscopy was used to estimate the volume fraction of the crystalline phase, which is in the range of 86 % to 98%. The stress values range between 150 and -140 MPa. The mechanical properties were studied by nanoindentation. Unlike monocrystalline wafers, there is no evidence of abrupt changes in the force-penetration plot, which have been attributed to a pressure-induced phase transition. The hardness was 12.5 GPa for the best samples, which is close to that obtained for silicon wafers.

Sign in / Sign up

Export Citation Format

Share Document