A GAUSSIAN MONOCYCLE PULSE GENERATOR/MODULATOR FOR UWB RADIOS APPLICATIONS

2014 ◽  
Vol 23 (05) ◽  
pp. 1450060 ◽  
Author(s):  
LEONARDO PANTOLI ◽  
VINCENZO STORNELLI
Keyword(s):  
Pulse Generator ◽  
Low Voltage ◽  
Low Complexity ◽  
Cmos Technology ◽  
Ultra Wideband ◽  
Repetition Time ◽  
Simulation Results ◽  
Uwb Applications ◽  
Uwb Radio ◽  
Circuit Power

In this paper, we present, at transistor level, a very low complexity Gaussian monocycle pulse generator/modulator for DPSK low voltage and low power tunable ultra-wideband (UWB) applications. The pulse generator, simulated in a SMIC 0.13 μm CMOS technology, provides a tunable, both in pulse width duration and repetition time, Gaussian monocycle compliant with the sub-GHz ETSI band and suitable to be used in UWB radio applications. The preliminary IC simulation results show a pulse duration from 1 ns up to 20 ns with good pulse symmetry and with the DPSK modulation capability. The circuit power consumption is about 1 mW from a 1.8 V power supply.

A 10T Cell Design without Half Select Problem for Bit-Interleaving Architecture in 65nm CMOS

2013 ◽  
Vol 373-375 ◽  
pp. 1607-1611
Author(s):  
Hong Gang Zhou ◽  
Shou Biao Tan ◽  
Qiang Song ◽  
Chun Yu Peng
Keyword(s):  
Error Correction ◽  
Low Voltage ◽  
Cmos Technology ◽  
Soft Error ◽  
Error Correction Codes ◽  
Cell Design ◽  
Low Voltage Operation ◽  
Sram Cell ◽  
Simulation Results ◽  
Nanometer Regime

With the scaling of process technologies into the nanometer regime, multiple-bit soft error problem becomes more serious. In order to improve the reliability and yield of SRAM, bit-interleaving architecture which integrated with error correction codes (ECC) is commonly used. However, this leads to the half select problem, which involves two aspects: the half select disturb and the additional power caused by half-selected cells. In this paper, we propose a new 10T cell to allow the bit-interleaving array while completely eliminating the half select problem, thus allowing low-power and low-voltage operation. In addition, the RSNM and WM of our proposed 10T cell are improved by 21% and nearly one times, respectively, as compared to the conventional 6T SRAM cell in SMIC 65nm CMOS technology. We also conduct a comparison with the conventional 6T cell about the leakage simulation results, which show 14% of leakage saving in the proposed 10T cell.

New Schmitt Trigger with Controllable Hysteresis using Dual Control Gate-Floating Gate Transistor (DCG-FGT)

2013 ◽  
Vol 2 (1) ◽  
pp. 49
Author(s):  
Abderrezak Marzaki ◽  
V. Bidal ◽  
R. Laffont ◽  
W. Rahajandraibe ◽  
J-M. Portal ◽  
...  
Keyword(s):  
Low Voltage ◽  
Schmitt Trigger ◽  
Cmos Technology ◽  
Floating Gate ◽  
Dual Control ◽  
Switching Voltage ◽  
Voltage Range ◽  
Rail To Rail ◽  
Floating Gate Transistor ◽  
Simulation Results

This paper presents different low voltage adjustable CMOS Schmitt trigger using DCG-FGT transistor. Simple circuits are introduced to provide flexibility to program the hysteresic threshold in this paper. The hysteresis can be controlled accurately at a large voltage range. The proposed Schmitt trigger have been designed using 90nm 1.2V CMOS technology and simulated using Eldo with PSP device models. The simulation results show rail-to-rail operation and adjustable switching voltages <em>V<sub>TH- </sub></em>(low switching voltage) and <em>V<sub>TH+ </sub></em>(high switching voltage).

A High-Linear CMOS Down Conversion Mixer Using Adjusting the Second and Third-Order Harmonic in Transconductance Stage

2014 ◽  
Vol 24 (01) ◽  
pp. 1550002 ◽  
Author(s):  
Mina Amiri ◽  
Adib Abrishamifar
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Circuit Simulation ◽  
Cmos Technology ◽  
Conversion Gain ◽  
Third Order ◽  
Cmos Mixer ◽  
Simulation Results ◽  
Down Conversion ◽  
Pmos Transistor

In this paper a new high-linear CMOS mixer is proposed. A well-known low voltage CMOS multiplier structure is used for mixer application in this paper and its linearity is provided by adjusting the value of a resistor, sizing the aspect ratio of a PMOS transistor and adding a proper value of inductor at the input stage. In simulation, a supply voltage as low as 1 V is applied to the circuit. Simulation results of improved mixer in a 0.18-μm CMOS technology illustrate 14 dB increases in IIP3 and also an increase around 1.4 dB is obtained in conversion gain. Furthermore, additional components which are used for improving linearity would not increase the power consumption and area significantly.

Sub-Volt Fully Balanced Differential Difference Amplifier

2014 ◽  
Vol 24 (01) ◽  
pp. 1550005 ◽  
Author(s):  
Fabian Khateb ◽  
Montree Kumngern ◽  
Spyridon Vlassis ◽  
Costas Psychalinos ◽  
Tomasz Kulej
Keyword(s):  
Low Voltage ◽  
Input Voltage ◽  
Cmos Technology ◽  
Floating Gate ◽  
Voltage Range ◽  
State Variable ◽  
Low Voltage Operation ◽  
Differential Difference Amplifier ◽  
Simulation Results ◽  
State Variable Filter

This paper presents a new CMOS structure for a fully balanced differential difference amplifier (FB-DDA) designed to operate from a sub-volt supply. This structure employs the bulk-driven quasi-floating-gate (BD-QFG) technique to achieve the capability of an ultra-low voltage operation and an extended input voltage range. The proposed BD-QFG FB-DDA is suitable for ultra-low-voltage low-power applications. The circuit is designed with a single supply of 0.5 V and consumes only 357 nW of power. The proposed circuit was simulated in a 0.18-μm TSMC CMOS technology and the simulation results prove its functionality and attractive parameters. An application example of a state variable filter is also presented to confirm the usefulness of the proposed BD-QFG FB-DDA.

Common Mode Feedback Circuits for Low Voltage Fully-Differential Amplifiers

2016 ◽  
Vol 25 (10) ◽  
pp. 1650124 ◽  
Author(s):  
S. Rekha ◽  
T. Laxminidhi
Keyword(s):  
Power Supply ◽  
Continuous Time ◽  
Efficient Solution ◽  
Low Voltage ◽  
Cmos Technology ◽  
Common Mode ◽  
Power Efficient ◽  
Differential Amplifiers ◽  
Fully Differential ◽  
Simulation Results

Continuous time common mode feedback (CMFB) circuits for low voltage, low power applications are proposed. Four circuits are proposed for gate/bulk-driven pseudo-differential transconductors operating on sub-1-V power supply. The circuits are validated for a bulk-driven pseudo-differential transconductor operating on 0.5[Formula: see text]V in 0.18[Formula: see text][Formula: see text]m standard CMOS technology. Simulation results reveal that the proposed CMFB circuits offer power efficient solution for setting the output common mode of the transconductors. They also load the transconductor capacitively offering capacitance of about 1[Formula: see text]fF to tens of femto farads.

Low Power Operational Transconductance Amplifier (OTA) with Enhanced DC Gain and Slew-Rate

2013 ◽  
Vol 411-414 ◽  
pp. 1645-1648
Author(s):  
Xiao Zong Huang ◽  
Lun Cai Liu ◽  
Jian Gang Shi ◽  
Wen Gang Huang ◽  
Fan Liu ◽  
...  
Keyword(s):  
Low Voltage ◽  
Cmos Technology ◽  
Optimization Techniques ◽  
Current Mirror ◽  
Slew Rate ◽  
Operational Transconductance Amplifier ◽  
Theory Analysis ◽  
Transconductance Amplifier ◽  
Dc Gain ◽  
Simulation Results

This paper presents a low-voltage differential operational transconductance amplifier (OTA) with enhanced DC gain and slew-rate. Based on the current mirror OTA topology, the optimization techniques are discussed in this work. The proposed structure achieves enhanced DC gain, unit gain frequency (UGF) and slew-rate (SR) with adding four devices. The design of the OTA is described with theory analysis. The OTA operates at the power supply of 1.8V. Simulation results for 0.18μm standard CMOS technology show that the DC gain increases from 60.6dB to 65dB, the UGF is optimized from 2.5MHz to 4.3MHz, the SR is enhanced from 0.88 V/μs to 4.8 V/μs with close power consumption dramatically.

130 nm CMOS Bulk-Driven Variable Gain Amplifier for Low-Voltage Applications

2017 ◽  
Vol 26 (08) ◽  
pp. 1740003 ◽  
Author(s):  
Daniel Arbet ◽  
Viera Stopjaková ◽  
Martin Kováč ◽  
Lukáš Nagy ◽  
Matej Rakús ◽  
...  
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Input Voltage ◽  
Cmos Technology ◽  
Variable Gain Amplifier ◽  
Voltage Range ◽  
Variable Gain ◽  
Wide Scale ◽  
Simulation Results ◽  
Low Supply Voltage

In this paper, a variable gain amplifier (VGA) designed in 130 nm CMOS technology is presented. The proposed amplifier is based on the bulk-driven (BD) design approach, which brings a possibility to operate with low supply voltage. Since the supply voltage of only 0.6 V is used for the amplifier to operate, there is no risk of latch-up event that usually represents the main drawback of the BD circuit systems. BD transistors are employed in the input differential stage, which makes it possible to operate in rail-to-rail input voltage range. Achieved simulation results indicate that gain of the proposed VGA can be varied in a wide scale, which together with the low supply voltage feature make the proposed amplifier useful for low-voltage and low-power applications. An additional circuit responsible for maintaining the linear-in-decibel gain dependency of the VGA is also addressed. The proposed circuit block avails arbitrary shaping of the curve characterizing the gain versus the controlling voltage dependency.

A Novel CNFET Technology Based 3 Bit Flash ADC for Low-Voltage High Speed SoC Application

2015 ◽  
Vol 19 ◽  
pp. 19-36 ◽  
Author(s):  
P.A. Gowri Sankar ◽  
G. Sathiyabama
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Circuit Design ◽  
Field Effect ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Flash Adc ◽  
Simulation Results

The continuous scaling down of metal-oxide-semiconductor field effect transistors (MOSFETs) led to the considerable impact in the analog-digital mixed signal integrated circuit design for system-on-chips (SoCs) application. SoCs trends force ADCs to be integrated on the chip with other digital circuits. These trends present new challenges in ADC circuit design based on existing CMOS technology. In this paper, we have designed and analyzed a 3-bit high speed, low-voltage and low-power flash ADC at 32nm CNFET technology for SoC applications. The proposed ADC utilizes the Threshold Inverter Quantization (TIQ) technique that uses two cascaded carbon nanotube field effect transistor (CNFET) inverters as a comparator. The TIQ technique proposed has been developed for better implementation in SoC applications. The performance of the proposed ADC is studied using two different types of encoders such as ROM and Fat tree encoders. The proposed ADCs circuits are simulated using Synopsys HSPICE with standard 32nm CNFET model at 0.9 input supply voltage. The simulation results show that the proposed 3 bit TIQ technique based flash ADC with fat tree encoder operates up to 8 giga samples per second (GSPS) with 35.88µW power consumption. From the simulation results, we observed that the proposed TIQ flash ADC achieves high speed, small size, low power consumption, and low voltage operation compared to other low power CMOS technology based flash ADCs. The proposed method is sensitive to process, temperature and power supply voltage variations and their impact on the ADC performance is also investigated.

Sign in / Sign up

Export Citation Format

Share Document