A Low-Noise High-Gain Recycling Folded Cascode Operational Transconductance Amplifier Based on Gate Driven and Quasi-Floating Bulk Technique

2021 ◽  
Author(s):  
Roowz Saini ◽  
Kulbhushan Sharma ◽  
Rajnish Sharma
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Monte Carlo Analysis ◽  
High Gain ◽  
Low Noise ◽  
Operational Transconductance Amplifier ◽  
Sensor Applications ◽  
Transconductance Amplifier ◽  
Folded Cascode

Operational Transconductance Amplifier (OTA) is an important circuit block used in the design of filter, amplifiers and oscillators for various analog-mixed circuit systems. However, design of a low-noise, high-gain OTA with low-power consumption is a challenging task in CMOS technology owing to high-power requirements of OTA for emulating high gain. This paper represents the design of gate-driven quasi-floating bulk recycling folded cascode (GDQFB RFC) OTA which has been shown to provide low-noise operation, emulates high gain and draws very less power. The design utilizes the gate-driven quasi-floating bulk (GDQFB) technique on a recycling folded cascode structure, which enhances the transconductance of OTA and improves its performance. All the post-layout simulation results have been obtained in 0.18-[Formula: see text]m CMOS N-well technology using BSIM3V3 device models. The obtained results indicate very high gain of 100.4 dB, gain-bandwidth of 69[Formula: see text]kHz, phase margin of 51.9∘ with power consumption of 2.31[Formula: see text][Formula: see text]W from [Formula: see text][Formula: see text]V supply voltage. The input referred noise emulated by proposed OTA is 0.684, 0.21 and 0.0592[Formula: see text][Formula: see text]V/[Formula: see text]Hz @ 1[Formula: see text]Hz, 10[Formula: see text]Hz and 1[Formula: see text]kHz, respectively. The input common mode range and output voltage swing are found to be [Formula: see text] to 0.669[Formula: see text]V and [Formula: see text] to 0.610[Formula: see text]V, respectively. Corner simulations and Monte Carlo analysis have been performed to verify the robustness of the proposed OTA. The proposed OTA can be used in design of filters and amplifiers for bio-instruments, sensor applications, neural recording applications and human implants etc.

Design of High Gain Folded Cascode OTA-Based Transconductance–Capacitance Loop Filter for PLL Applications

2021 ◽  
pp. 2150263
Author(s):  
Priti Gupta ◽  
Sanjay Kumar Jana
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
High Gain ◽  
Cmos Process ◽  
Operational Transconductance Amplifier ◽  
Loop Filter ◽  
Transconductance Amplifier ◽  
Dc Gain ◽  
Unity Gain ◽  
Folded Cascode

This paper deals with the designing of low-power transconductance–capacitance-based loop filter. The folded cascode-based operational transconductance amplifier (OTA) is designed in this paper with the help of quasi-floating bulk MOSFET that achieved the DC gain of 88.61[Formula: see text]dB, unity gain frequency of 97.86[Formula: see text]MHz and power consumption of 430.62[Formula: see text][Formula: see text]W. The proposed OTA is compared with the exiting OTA structure which showed 19.50% increase in DC gain and 15.11% reduction in power consumption. Further, the proposed OTA is used for the designing of transconductance–capacitance-based loop filter that has been operated at [Formula: see text]3[Formula: see text]dB cut-off frequency of 30.12[Formula: see text]MHz with the power consumption of 860.90[Formula: see text][Formula: see text]W at the supply voltage of [Formula: see text][Formula: see text]V. The transistor-level simulation has been done in 0.18[Formula: see text][Formula: see text]m CMOS process.

High Gain and High CMRR Two-Stage Folded Cascode OTA with Nested Miller Compensation

2015 ◽  
Vol 24 (04) ◽  
pp. 1550057 ◽  
Author(s):  
Meysam Akbari ◽  
Omid Hashemipour
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Open Loop ◽  
Two Stage ◽  
Miller Compensation ◽  
Transconductance Amplifier ◽  
Dc Gain ◽  
Folded Cascode

By using Gm-C compensation (GCC) technique, a two-stage recycling folded cascode (FC) operational transconductance amplifier (OTA) is designed. The proposed configuration consists of recycling structure, positive feedback and feed-forward compensation path. In comparison with the typical folded cascode CMOS Miller amplifier, this design has higher DC gain, unity-gain frequency (UGF), slew rate and common mode rejection ratio (CMRR). The presented OTA is simulated in 0.18-μm CMOS technology and the simulation results confirm the theoretical analyses. Finally, the proposed amplifier has a 111 dB open-loop DC gain, 20 MHz UGF and 145 dB CMRR @ 1.2 V supply voltage while the power consumption is 400 μW which makes it suitable for low-voltage applications.

scholarly journals Ultra-Low-Voltage Low-Power Bulk-Driven Quasi-Floating-Gate Operational Transconductance Amplifier

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Ziad Alsibai ◽  
Salma Bay Abo Dabbous
Keyword(s):  
Signal Processing ◽  
Power Consumption ◽  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Bias Current ◽  
Floating Gate ◽  
Operational Transconductance Amplifier ◽  
Transconductance Amplifier

A new ultra-low-voltage (LV) low-power (LP) bulk-driven quasi-floating-gate (BD-QFG) operational transconductance amplifier (OTA) is presented in this paper. The proposed circuit is designed using 0.18 μm CMOS technology. A supply voltage of ±0.3 V and a quiescent bias current of 5 μA are used. The PSpice simulation result shows that the power consumption of the proposed BD-QFG OTA is 13.4 μW. Thus, the circuit is suitable for low-power applications. In order to confirm that the proposed BD-QFG OTA can be used in analog signal processing, a BD-QFG OTA-based diodeless precision rectifier is designed as an example application. This rectifier employs only two BD-QFG OTAs and consumes only 26.8 μW.

scholarly journals A 60 GHz fully differential LNA in 90 nm CMOS technology

2013 ◽  
Vol 6 (2) ◽  
pp. 109-113 ◽  
Author(s):  
Andrea Malignaggi ◽  
Amin Hamidian ◽  
Georg Boeck
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Transmission Lines ◽  
Noise Figure ◽  
Design Procedure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Differential

The present paper presents a fully differential 60 GHz four stages low-noise amplifier for wireless applications. The amplifier has been optimized for low-noise, high-gain, and low-power consumption, and implemented in a 90 nm low-power CMOS technology. Matching and common-mode rejection networks have been realized using shielded coplanar transmission lines. The amplifier achieves a peak small-signal gain of 21.3 dB and an average noise figure of 5.4 dB along with power consumption of 30 mW and occupying only 0.38 mm2pads included. The detailed design procedure and the achieved measurement results are presented in this work.

A LOW POWER CRYOGENIC CMOS ROIC DESIGN FOR 512 × 512 IRFPA

2013 ◽  
Vol 22 (10) ◽  
pp. 1340033 ◽  
Author(s):  
HONGLIANG ZHAO ◽  
YIQIANG ZHAO ◽  
YIWEI SONG ◽  
JUN LIAO ◽  
JUNFENG GENG
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Integrated Circuit ◽  
High Performance ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Readout Integrated Circuit ◽  
Chip Area ◽  
Operating Modes

A low power readout integrated circuit (ROIC) for 512 × 512 cooled infrared focal plane array (IRFPA) is presented. A capacitive trans-impedance amplifier (CTIA) with high gain cascode amplifier and inherent correlated double sampling (CDS) configuration is employed to achieve a high performance readout interface for the IRFPA with a pixel size of 30 × 30 μm2. By optimizing column readout timing and using two operating modes in column amplifiers, the power consumption is significantly reduced. The readout chip is implemented in a standard 0.35 μm 2P4M CMOS technology. The measurement results show the proposed ROIC achieves a readout rate of 10 MHz with 70 mW power consumption under 3.3 V supply voltage from 77 K to 150 K operating temperature. And it occupies a chip area of 18.4 × 17.5 mm2.

A Low-Power, High-Gain, and Low-Noise 802.11a Down-Conversion Mixer in 0.35-μm SiGe Bi-CMOS Technology

2017 ◽  
Vol 26 (09) ◽  
pp. 1750134 ◽  
Author(s):  
Jun-Da Chen ◽  
Song-Hao Wang
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Conversion Gain ◽  
Dc Power ◽  
Down Conversion

The paper presents a novel 5.15[Formula: see text]GHz–5.825[Formula: see text]GHz SiGe Bi-CMOS down-conversion mixer for WLAN 802.11a receiver. The architecture used is based on Gilbert cell mixer, the combination of MOS transistors and HBT BJT transistor device characteristics. The hetero-junction bipolar transistor (HBT) topology is adopted at the transconductance stage to improve power gain and reduce noise factor, and the LO series-parallel CMOS switch topology will be applied to reduce supply voltage and dc power at the switching stage. This mixer is implemented in TSMC 0.35-[Formula: see text]m SiGe Bi-CMOS process, and the chip size including the test pads is 1.175*0.843[Formula: see text]mm2. The main advantages for the proposed mixer are high conversion gain, a moderate linearity, low noise figure, and low power. The post-simulation results achieved are as follows: 14[Formula: see text]dB power conversion gain, [Formula: see text]6[Formula: see text]dBm input third-order intercept point (IIP3), 6.85[Formula: see text]dB double side band (DSB) noise figure. The total mixer current is about 1.54[Formula: see text]mA from 1.4[Formula: see text]V supply voltage including output buffer. The total dc power consumption is 2.15[Formula: see text]mW.

scholarly journals A concurrent dual-band CMOS low noise amplifier at 2.4/5.2 GHz for WLAN applications

2019 ◽  
Vol 14 (2) ◽  
pp. 555
Author(s):  
S.A.Z. Murad ◽  
A. F. Hasan ◽  
A. Azizan ◽  
A. Harun ◽  
J. Karim
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Notch Filter ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Dual Band ◽  
Common Source ◽  
Noise Amplifier

<span>This paper presents a concurrent dual-band CMOS low noise amplifier (LNA) at operating frequency of 2.4 GHz and 5.2 GHz for WLAN applications. The proposed LNA employed cascode common source to obtain high gain using 0.13-µm CMOS technology. The concurrent dual-band frequencies are matched using LC network band-pass and band-stop notch filter at the input and output stages. The filters help to shape the frequency response of the proposed LNA. The simulation results indicate that the LNA achieves a forward gain of 21.8 dB and 14.22 dB, input return loss of -18 dB and -14 dB at 2.4 GHz and 5.2 GHz, respectively. The noise figure of 4.1 dB and 3.5 dB with the input third-order intercept points 7 dBm and 10 dBm are obtained at 2.4 GHz and 5.2 GHz, respectively. The LNA dissipates 2.4 mW power at 1.2 V supply voltage with a chip size of 1.69 mm2.</span>

scholarly journals Design of a LNA in the frequency band 1.8-2.2GHz in 0.13μm CMOS Technology

2005 ◽  
Vol 3 ◽  
pp. 299-303
Author(s):  
E. Di Gioia ◽  
C. Hermann ◽  
H. Klar
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Low Cost ◽  
Operating Mode ◽  
Cmos Technology ◽  
Digital Circuit ◽  
High Gain ◽  
Low Noise ◽  
Noise Amplifier ◽  
Low Supply Voltage

Abstract. The subject of this work is a low noise amplifier (LNA), operating in the frequency range 1.8-2.1GHz. The CMOS 0.13μm technology is used in respect to the low cost of the final device. Among the specifications, a variable gain and an adjustable working frequency are required. In particular, four different working modes are provided: 1.8, 1.9 and 2.1GHz high gain and 2.1GHz low gain. The amplifier is designed to be used as first stage of a receiver for mobile telephony. For this reason low power consumption is taken into consideration (low supply voltage and low drain currents). A simple digital circuit, integrated on-chip, is used to select the operating mode of the LNA by means of two input pins. A Noise figure of 1dB is obtained with a supply voltage of 0.8V.

scholarly journals High-Precision Current Conveyor based on BDQFG Miller Ota

2019 ◽  
Vol 8 (2) ◽  
pp. 823-826
Keyword(s):  
Frequency Response ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Current Conveyor ◽  
Floating Gate ◽  
High Current ◽  
Operational Transconductance Amplifier ◽  
Transconductance Amplifier ◽  
High Bandwidth ◽  
Low Supply Voltage

The paper presents a sub-volt design of highly precise second-generation current conveyor (CCII  ) using Miller compensated Operational Transconductance Amplifier (OTA) designed using bulk driven quasi-floating gate (BDQFG) MOSFET. The bulk-driven approach help in working of proposed CCII  at low supply voltage. Moreover, followed BDQFG technique results in improves the transconductance and frequency response of the circuit over standalone bulk-driven technique. The proposed CCII  operates at  0.4V. Other performances which encourage its wide applicability are in terms of high current range and high bandwidth. The analysis of proposed current conveyor is carried in 0.18 m twin-well CMOS technology using HSpice

scholarly journals Design of Low Voltage Low Power High Gain Operational Transconductance Amplifier

2021 ◽  
Vol 7 (4) ◽  
pp. 103-110
Author(s):  
Rajesh Durgam ◽  
S. Tamil ◽  
Nikhil Raj
Keyword(s):  
Low Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Floating Gate ◽  
Operational Transconductance Amplifier ◽  
Linear Mode ◽  
Low Voltage Operation ◽  
Transconductance Amplifier ◽  
Amplifier Design ◽  
Self Cascode

In this paper, a high gain structure of operational transconductance amplifier is presented. For low voltage operation with improved frequency response bulk driven quasi-floating gate MOSFET is used at the input. Further for achieving high gain the modified self cascode structure is used at the output. Compared to conventional self cascode the modified self cascode structure used provides higher transconductance which helps in significant boosting of gain of the amplifier. The modification is achieved by employing quasi-floating gate transistor which helps in scaling of the threshold which as a result increases the drain-to-source voltage of linear mode transistor thus changing it to saturation. This change of mode boosts the effective transconductance of self cascode MOSFET. The proposed operational transconductance amplifier when compared to its conventional showed improvement in DC gain by 30dB and also the unity gain bandwidth increases by 6 fold. The MOS models used for amplifier design are of 0.18µm CMOS technology at supply of 0.5V.

Sign in / Sign up

Export Citation Format

Share Document