Effects of Self-Stress Distributions on Stability of Tensegrity Structures

2017 ◽  
Vol 17 (03) ◽  
pp. 1750029 ◽  
Author(s):  
B. Shekastehband ◽  
N. Pourmand
Keyword(s):  
Stress Distribution ◽  
Dominant Role ◽  
Stress Distributions ◽  
Stability Behavior ◽  
Collapse Mechanisms ◽  
Tensegrity Systems ◽  
Load Carrying ◽  
Key Factor ◽  
The Stability ◽  
Selection Of

Tensegrity systems are composed of any given set of cables connected to a set of struts in which the cables connectivity must be able to stabilize the configuration. Self-stresses contribute to the rigidity and stability of the system. Therefore, self-stress distribution has a dominant effect on the stability behavior of these systems. In this study, the stability behavior of plane double-layer tensegrity systems considering different distributions of self-stresses is evaluated. Based on the results obtained, collapse mechanisms, load carrying capacities, stiffness of the systems and slackening of the cables are affected by self-stress distribution. Therefore, self-stress design is a key factor that plays a dominant role on the stability behavior of tensegrity systems. These results can lead to the suggestion of some guidelines on the selection of self-stress distribution for the design of tensegrity systems against instability.

Effect of Finite Thickness Flexible Boundary Upon the Stability of a Poiseuille Flow

1990 ◽  
Vol 57 (4) ◽  
pp. 1056-1060 ◽  
Author(s):  
Mauro Pierucci ◽  
Pedro G. Morales
Keyword(s):  
Poiseuille Flow ◽  
Finite Thickness ◽  
Stress Distributions ◽  
Stability Equation ◽  
Stability Behavior ◽  
Different Types ◽  
Improved Stability ◽  
Numerical Instabilities ◽  
The Stability ◽  
Sommerfeld Equation

The stability behavior, the stress, and velocity distributions for a plane Poiseuille flow bounded by a finite thickness elastic layer is studied. The analysis is performed by utilizing the coupled relationships between the Orr-Sommerfeld stability equation for the fluid and the Navier equations for the solid. The numerical instabilities experienced in the solution of the Orr-Sommerfeld equation have been overcome with the use of Davey’s orthonormalization technique. This study focuses only on the Tollimen-Schlichting instabilities. This mode is the most unstable of the three different types of instabilities. The results show that certain combinations of parameters can lead to improved stability conditions. Under these conditions the normal and shear stress distributions may behave completely different in certain regions of the fluid.

Numerical Analysis of Static Characteristics of Herringbone Grooved Hydrodynamic Journal Bearing

2011 ◽  
Vol 105-107 ◽  
pp. 2259-2262
Author(s):  
Han Ting Zhu ◽  
Qian Ding
Keyword(s):  
Journal Bearing ◽  
Normal Pressure ◽  
Differential Method ◽  
Static Characteristics ◽  
Load Carrying ◽  
Significant Performance ◽  
Hydrodynamic Journal Bearing ◽  
The Stability ◽  
Spiral Angle ◽  
Selection Of

By means of the finite differential method, the Reynolds equation is solved and the static characteristics of herringbone grooved hydrodynamic journal bearing are numerically analyzed by presenting the circumferential and axial pressures. The influences of parameters such as the eccentricity, width-diameter ratio of bearing, spiral angle, depth and number of grooves, on the static characteristics of herringbone grooved bearing are discussed. The results indicate that the normal pressure of oil film and the load carrying capacity as well, of herringbone grooved bearing will decrease with the increase of groove number and depth. On the other hand, as the pressure distributes in wider area in the circumferential direction, the stability of bearing can be improved. In consideration of these two aspects, the optimal groove number is 8-12, and the selection of depth and screw angle of grooves should also be chosen carefully to obtain the significant performance of herringbone grooved bearing.

EVALUATION OF HYBRID SPRING WHEAT POPULATIONS

2018 ◽  
pp. 37-39
Author(s):  
O. V. Gladysheva ◽  
Т. А. Barkovskaya
Keyword(s):  
Correlation Coefficient ◽  
Spring Wheat ◽  
Dominant Role ◽  
F1 Hybrids ◽  
Hybrid Population ◽  
Selection Of

This article presents the results of a study of hybrid spring wheat populations. Revealed different patterns of inheritance of important traits in F1 hybrids, which is caused by hereditary features of the original forms and circumstances. Analysis of hybrid populations showed that the dominant role in the formation of 1000 grains mass belongs to productivity and weight of grain with an ear, correlation coefficient r = 0.90 and amounted to r = 0.73, respectively. Found that the hybrid population in F4-5, created on the basis of grades Moscow 35, Esther, Agatha, Rome, Saratovskaya 29 (Russia), Ostinka (Ukraine) are a valuable material for selection of highly productive genotypes for future use breeding process. 

scholarly journals Spatio-temporal selection of reference genes in the two congeneric species of Glycyrrhiza

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yuping Li ◽  
Xiaoju Liang ◽  
Xuguo Zhou ◽  
Yu An ◽  
Ming Li ◽  
...  
Keyword(s):  
Gene Expression ◽  
Developmental Stage ◽  
Reference Genes ◽  
Developmental Stages ◽  
Individual Factors ◽  
Congeneric Species ◽  
Spatio Temporal ◽  
The Stability ◽  
Different Tissues ◽  
Selection Of

AbstractGlycyrrhiza, a genus of perennial medicinal herbs, has been traditionally used to treat human diseases, including respiratory disorders. Functional analysis of genes involved in the synthesis, accumulation, and degradation of bioactive compounds in these medicinal plants requires accurate measurement of their expression profiles. Reverse transcription quantitative real-time PCR (RT-qPCR) is a primary tool, which requires stably expressed reference genes to serve as the internal references to normalize the target gene expression. In this study, the stability of 14 candidate reference genes from the two congeneric species G. uralensis and G. inflata, including ACT, CAC, CYP, DNAJ, DREB, EF1, RAN, TIF1, TUB, UBC2, ABCC2, COPS3, CS, R3HDM2, were evaluated across different tissues and throughout various developmental stages. More importantly, we investigated the impact of interactions between tissue and developmental stage on the performance of candidate reference genes. Four algorithms, including geNorm, NormFinder, BestKeeper, and Delta Ct, were used to analyze the expression stability and RefFinder, a comprehensive software, provided the final recommendation. Based on previous research and our preliminary data, we hypothesized that internal references for spatio-temporal gene expression are different from the reference genes suited for individual factors. In G. uralensis, the top three most stable reference genes across different tissues were R3HDM2, CAC and TUB, while CAC, CYP and ABCC2 were most suited for different developmental stages. CAC is the only candidate recommended for both biotic factors, which is reflected in the stability ranking for the spatio (tissue)-temporal (developmental stage) interactions (CAC, R3HDM2 and DNAJ). Similarly, in G. inflata, COPS3, R3HDM2 and DREB were selected for tissues, while RAN, COPS3 and CS were recommended for developmental stages. For the tissue-developmental stage interactions, COPS3, DREB and ABCC2 were the most suited reference genes. In both species, only one of the top three candidates was shared between the individual factors and their interactions, specifically, CAC in G. uralensis and COPS3 in G. inflata, which supports our overarching hypothesis. In summary, spatio-temporal selection of reference genes not only lays the foundation for functional genomics research in Glycyrrhiza, but also facilitates these traditional medicinal herbs to reach/maximize their pharmaceutical potential.

scholarly journals Optimize Design of Run-Flat Tires by Simulation and Experimental Research

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 474
Author(s):  
Huaqiao Liu ◽  
Yiren Pan ◽  
Huiguang Bian ◽  
Chuansheng Wang
Keyword(s):  
Stress Distribution ◽  
Energy Loss ◽  
Successful Implementation ◽  
Performance Tests ◽  
Key Factors ◽  
Heat Accumulation ◽  
Factors Affecting ◽  
Structural Rigidity ◽  
Key Factor ◽  
Durability Testing

In this study, the two key factors affecting the thermal performance of the insert rubber and stress distribution on the tire sidewall were analyzed extensively through various performance tests and simulations to promote the development of run-flat tires. Four compounds and two structures of insert rubber were designed to investigate the effects of heat accumulation and stress distribution on durability testing at zero pressure. It was concluded that the rigidity and tensile strength of the compound were negatively correlated with temperature. The deformation was a key factor that affects energy loss, which could not be judged solely by the loss factor. The stress distribution, however, should be considered in order to avoid early damage of the tire caused by stress concentration. On the whole, the careful balance of mechanical strength, energy loss, and structural rigidity was the key to the optimal development of run-flat tires. More importantly, the successful implementation of the simulations in the study provided important and useful guidance for run-flat tire development.

Stabilization of networked switched affine systems with event-triggered strategy

2021 ◽  
pp. 014233122110213
Author(s):  
Dandan Li ◽  
Zhiqiang Zuo ◽  
Yijing Wang
Keyword(s):  
Affine Systems ◽  
Switching Law ◽  
Event Time ◽  
Sliding Motion ◽  
State Dependent ◽  
Event Triggering ◽  
Stability Issue ◽  
The Stability ◽  
Event Based ◽  
Selection Of

Using an event-based switching law, we address the stability issue for continuous-time switched affine systems in the network environment. The state-dependent switching law in terms of the region function is firstly developed. We combine the region function with the event-triggering mechanism to construct the switching law. This can provide more candidates for the selection of the next activated subsystem at each switching instant. As a result, it is possible for us to activate the appropriate subsystem to avoid the sliding motion. The Zeno behavior for the switched affine system can be naturally ruled out by guaranteeing a positive minimum inter-event time between two consecutive executions of the event-triggering threshold. Finally, two numerical examples are given to demonstrate the effectiveness of the proposed method.

scholarly journals Procedure for the Selection of Rubber Compound in Rubber-Metal Springs for Vibration Isolation

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1737
Author(s):  
Milan Banić ◽  
Dušan Stamenković ◽  
Aleksandar Miltenović ◽  
Dragan Jovanović ◽  
Milan Tica
Keyword(s):  
Numerical Simulation ◽  
Constitutive Model ◽  
Vibration Isolation ◽  
Correct Selection ◽  
Virtual Experiment ◽  
Rubber Compound ◽  
Key Factor ◽  
Railway Engineering ◽  
Selection Of

The selection of a rubber compound has a determining influence on the final characteristics of rubber-metal springs. Therefore, the correct selection of a rubber compound is a key factor for development of rubber-metal vibration isolation springs with required characteristics. The procedure for the selection of the rubber compound for vibration isolation of rubber-metal springs has been proposed, so that the rubber-metal elements have the necessary characteristics, especially in terms of deflection. The procedure is based on numerical simulation of spring deflection with Bergström-Boyce constitutive model in virtual experiment, with a goal to determine which parameters of the constitutive model will lead to spring required deflection. The procedure was verified by case study defined to select rubber compound for a rubber–metal spring used in railway engineering.

Finite Element Analysis of Poor Distal Contact of the Femoral Component of a Cementless Hip Endoprosthesis

1993 ◽  
Vol 207 (4) ◽  
pp. 255-261 ◽  
Author(s):  
M Taylor ◽  
E W Abel
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Influencing Factor ◽  
Three Dimensional ◽  
Stress Distributions ◽  
Element Analysis ◽  
Hip Endoprosthesis ◽  
Applied Loading ◽  
Femoral Geometry ◽  
Contact Models

The difficulty of achieving good distal contact between a cementless hip endoprosthesis and the femur is well established. This finite element study investigates the effect on the stress distribution within the femur due to varying lengths of distal gap. Three-dimensional anatomical models of two different sized femurs were generated, based upon computer tomograph scans of two cadaveric specimens. A further six models were derived from each original model, with distal gaps varying from 10 to 60 mm in length. The resulting stress distributions within these were compared to the uniform contact models. The extent to which femoral geometry was an influencing factor on the stress distribution within the bone was also studied. Lack of distal contact with the prosthesis was found not to affect the proximal stress distribution within the femur, for distal gap lengths of up to 60 mm. In the region of no distal contact, the stress within the femur was at normal physiological levels associated with the applied loading and boundary conditions. The femoral geometry was found to have little influence on the stress distribution within the cortical bone. Although localized variations were noted, both femurs exhibited the same general stress distribution pattern.

scholarly journals Selection of Adequate Species for Degraded Areas by Oil‐Exploitation Industry as a Key Factor for Recovery Forest in the Ecuadorian Amazon

2016 ◽  
Vol 27 (7) ◽  
pp. 1771-1780 ◽  
Author(s):  
Jaime Villacís ◽  
Cristina Armas ◽  
Susana Hang ◽  
Fernando Casanoves
Keyword(s):  
Oil Exploitation ◽  
Ecuadorian Amazon ◽  
Key Factor ◽  
Selection Of

scholarly journals Coupled THM and Matrix Stability Modeling of Hydroshearing Stimulation in a Coupled Fracture-Matrix Hot Volcanic System

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Yong Xiao ◽  
Jianchun Guo ◽  
Hehua Wang ◽  
Lize Lu ◽  
John McLennan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conduction ◽  
Dominant Role ◽  
Injection Well ◽  
Time Step ◽  
Volcanic System ◽  
Induced Stress ◽  
The Matrix ◽  
Matrix Stability ◽  
The Stability

A coupled thermal-hydraulic-mechanical (THM) model is developed to simulate the combined effect of fracture fluid flow, heat transfer from the matrix to injected fluid, and shearing dilation behaviors in a coupled fracture-matrix hot volcanic reservoir system. Fluid flows in the fracture are calculated based on the cubic law. Heat transfer within the fracture involved is thermal conduction, thermal advection, and thermal dispersion; within the reservoir matrix, thermal conduction is the only mode of heat transfer. In view of the expansion of the fracture network, deformation and thermal-induced stress model are added to the matrix node’s in situ stress environment in each time step to analyze the stability of the matrix. A series of results from the coupled THM model, induced stress, and matrix stability indicate that thermal-induced aperture plays a dominant role near the injection well to enhance the conductivity of the fracture. Away from the injection well, the conductivity of the fracture is contributed by shear dilation. The induced stress has the maximum value at the injection point; the deformation-induced stress has large value with smaller affected range; on the contrary, thermal-induced stress has small value with larger affected range. Matrix stability simulation results indicate that the stability of the matrix nodes may be destroyed; this mechanism is helpful to create complex fracture networks.

Sign in / Sign up

Export Citation Format

Share Document