scholarly journals Effect of Cu Addition on the Electrochemical Corrosion Performance of Ni3Al in 1.0 M H2SO4

2015 ◽  
Vol 2015 ◽  
pp. 1-18 ◽  
Author(s):  
J. Porcayo-Calderon ◽  
R. A. Rodriguez-Diaz ◽  
E. Porcayo-Palafox ◽  
J. Colin ◽  
A. Molina-Ocampo ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Electrochemical Corrosion ◽  
Open Circuit ◽  
Intermetallic Alloy ◽  
Intermetallic Alloys ◽  
Corrosion Performance ◽  
Linear Polarization Resistance ◽  
Electrochemical Corrosion Behavior

The effect of Cu addition on the electrochemical corrosion behavior of Ni3Al intermetallic alloy was investigated by potentiodynamic polarization, open-circuit potential, linear polarization resistance, and electrochemical impedance spectroscopy in 1.0 M H2SO4solution. Performance of the pure elements (Cu, Ni, and Al) was also evaluated. In general, Cu addition improved the corrosion resistance of Ni3Al. Electrochemical measurements show that corrosion resistance of Ni3Al-1Cu alloy is lower than that of other intermetallic alloys and pure elements (Ni, Cu, and Al) in 1.0 M H2SO4solution at 25°C. Surface analysis showed that the Ni3Al alloys are attacked mainly through the dendritic phases, and Cu addition suppresses the density of dendritic phases.

Electrochemical corrosion behavior of HVOF sprayed WC–12Co coating on H13 hot work mould steel

2019 ◽  
Vol 66 (6) ◽  
pp. 827-834
Author(s):  
Kong Weicheng ◽  
Shen Hui ◽  
Gao Jiaxu ◽  
Wu Jie ◽  
Lu Yuling
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Electrochemical Corrosion ◽  
Open Circuit ◽  
Curvature Radius ◽  
Nacl Solution ◽  
Content Type ◽  
Capacitance Curve ◽  
Electrochemical Corrosion Behavior ◽  
Corrosion Behaviors

Purpose This study aims to investigate the electrochemical corrosion performance of high velocity oxygen fuel (HVOF) sprayed WC–12Co coating in 3.5 Wt.% NaCl solution, which provided a guiding significance on the corrosion resistance of H13 hot work mould steel. Design/methodology/approach A WC–12Co coating was fabricated on H13 hot work mould steel using a HVOF, and the electrochemical corrosion behaviors of WC–12Co coating and substrate in 3.5 Wt.% NaCl solution was measured using open circuit potential (OCP), potentiodynamic polarization curve (PPC) and electrochemical impedance spectroscopy (EIS) tests. Findings The OCP and PPC of WC–12Co coating positively shift than those of substrate, its corrosion tendency and corrosion rate decrease to enhance its corrosion resistance. The curvature radius of capacitance curve on the WC–12Co coating is larger than that on the substrate, and the impedance and polarization resistance of WC–12Co coating increase faster than those of substrate, which reduces the corrosion process. Originality/value The electrochemical corrosion behaviors of WC–12Co coating and substrate in 3.5 Wt.% NaCl solution is first measured using OCP, PPC and EIS tests, which improve the electrochemical corrosion resistance of H13 hot work mould steel.

scholarly journals Microstructure and Corrosion Resistance to H2S in the Welded Joints of X80 Pipeline Steel

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1325 ◽  
Author(s):  
Jian-Bao Wang ◽  
Guang-Chun Xiao ◽  
Wei Zhao ◽  
Bing-Rong Zhang ◽  
Wei-Feng Rao
Keyword(s):  
Corrosion Resistance ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
Electrochemical Impedance ◽  
Pipeline Steel ◽  
Electrochemical Corrosion ◽  
Open Circuit ◽  
Coarse Grained ◽  
Granular Bainite ◽  
X80 Pipeline Steel

The microstructure and corrosion resistance in H2S environments for various zones of X80 pipeline steel submerged arc welded joints were studied. The main microstructures in the base metal (BM), welded metal (WM), coarse-grained heat-affected zone (CGHAZ), and fine-grained heat-affected zone (FGHAZ) were mainly polygonal ferrite and granular bainite; acicular ferrite with fine grains; granular bainite, ferrite, and martensite/austenite constituents, respectively. The corrosion behavior differences resulted from the microstructure gradients. The results of the micro-morphologies of the corrosion product films and the electrochemical corrosion characteristics in H2S environments, including open circuit potential and electrochemical impedance spectroscopy, showed that the order of corrosion resistance was FGHAZ > BM > WM > CGHAZ.

Corrosion Behavior of Surfaced AM50 Magnesium Alloys under Stress Conditions

2010 ◽  
Vol 95 ◽  
pp. 79-83
Author(s):  
Amir Eliezer
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloys ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Spinel Phase ◽  
Ceramic Coatings ◽  
Open Circuit ◽  
Stress Conditions ◽  
X Ray Diffraction ◽  
X Ray

Micro-arc oxidization of AM50 magnesium alloys was studied. The influence of micro-arc oxidization process was investigated; phase structure were analyzed using X-ray diffraction (XRD). Open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) were used to evaluate the corrosion resistance of ceramic coatings formed on magnesium alloys under stress conditions. XRD analyses indicate that the ceramic coatings fabricated on the surface of magnesium alloys by micro-arc oxidization are composed of spinel phase MgAl2O4 The corrosion resistance of ceramic coatings is improved compared with magnesium alloy substrate.

Electrochemical Determination of the Corrosion Resistance of Ag-Pd Dental Alloys

2008 ◽  
Vol 59 (9) ◽  
Author(s):  
Daniel Mareci ◽  
Igor Cretescu ◽  
Neculai Aelenei ◽  
Julia Claudia Mirza Rosca
Keyword(s):  
Corrosion Resistance ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Corrosion Behaviour ◽  
Artificial Saliva ◽  
Surface Film ◽  
Electrochemical Determination ◽  
Open Circuit ◽  
Electrochemical Characteristics

The electrochemical behavior of a three Ag-Pd alloys used in dental prosthetics construction for crowns and bridges was studied in artificial saliva using the polarization curves and electrochemical impedance spectroscopy (EIS). The corrosion resistance was evaluated by means of the corrosion currents value and by coulometric analysis. The open circuit potential of Ag-Pd are attributed to dealloying followed by surface enrichment with Ag and the possible formation of an insoluble AgCl surface film on the respective alloy surfaces. Our results have shown that these alloys have a somewhat good corrosion resistance in artificial saliva. When increasing the content of Cu, corrosion resistance decreases. The passivation of all samples occurred spontaneously at the open circuit potential. The electrochemical properties of the spontaneously passivated electrodes at the open circuit potential were studied by EIS. The polarization resistance (Rp) and the electrode capacitance (Cdl) were determined. The polarisation resistance of all the samples increases with the immersion time. The polarization resistances are largest and decrease when increasing the content of Cu. Cu reduces the Ag-Pd alloy corrosion resistance. The present study, thought limited, has shown that electrochemical characteristics can be use to identify such alloys. Knowledge of the in vitro corrosion behaviour of these alloys may lead to better understanding of any biologically adverse effects in vitro.

scholarly journals Influence of Ultrasonic Excitation Sealing on the Corrosion Resistance of HVOF-Sprayed Nanostructured WC-CoCr Coatings under Different Corrosive Environments

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 724 ◽  
Author(s):  
Zhang ◽  
Hong ◽  
Lin ◽  
Zheng
Keyword(s):  
Corrosion Resistance ◽  
Atmospheric Pressure ◽  
Room Temperature ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Aluminum Phosphate ◽  
Open Circuit ◽  
Corrosive Environments ◽  
Oxygen Fuel

The corrosion behavior of unsealed and sealed high-velocity oxygen-fuel (HVOF)-sprayed nanostructured WC-CoCr cermet coatings under different corrosive environments was investigated using scanning electron microscopy (SEM), open circuit potential (OCP), potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). Ultrasonic excitation sealing with aluminum phosphate was performed in an external ultrasonic bath with the frequency of 40 kHz at atmospheric pressure and room temperature. SEM micrographs revealed that the exposed area of the coating was effectively reduced by the coverage of aluminum phosphate sealant on the majority of pores. Electrochemical measurements demonstrated that the sealant with the help of ultrasonic energy could shift the corrosion potential to a more noble direction, reduce the corrosion current density, increase the resistance of charge transfer, and effectively improve the corrosion resistance of the coating in both 3.5 wt % NaCl and 1 mol·L−1 HCl solutions.

scholarly journals Effect of Nd3+ Ion Concentration on the Corrosion Resistance of API X70 Steel in Chloride-Rich Environments

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
D. M. Martinez de la Escalera ◽  
J. J. Ramos-Hernandez ◽  
E. Porcayo-Palafox ◽  
J. Porcayo-Calderon ◽  
J. G. Gonzalez-Rodriguez ◽  
...  
Keyword(s):  
Open Circuit Potential ◽  
Inhibition Efficiency ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Protective Layer ◽  
Open Circuit ◽  
Chloride Ions ◽  
Ion Concentration ◽  
Linear Polarization Resistance ◽  
Potentiodynamic Polarization Curves

In this study, the effect of the addition of Nd3+ ions as a corrosion inhibitor of the API X70 steel in a medium rich in chlorides was evaluated. The performance of the Nd3+ ions was evaluated by means of electrochemical techniques such as potentiodynamic polarization curves, open circuit potential measurements, linear polarization resistance, and electrochemical impedance spectroscopy, as well as by means of scanning electron microscopy and EDS measurements. The results showed that Nd3+ ions reduce the corrosion rate of steel at concentrations as low as 0.001 M Nd3+. At higher concentrations, the inhibition efficiency was only slightly affected although the concentration of chloride ions was increased by the addition of the inhibitor. The adsorption of the Nd3+ ions promotes the formation of a protective layer of oxides/hydroxides on the metal surface, thereby reducing the exchange rate of electrons. Nd3+ ions act as a mixed inhibitor with a strong predominant cathodic effect.

Effect of High-Intensity Pulsed Ion Beam Irradiation on the Electrochemical Corrosion Behavior of AZ31 Magnesium Alloy

2011 ◽  
Vol 189-193 ◽  
pp. 571-574
Author(s):  
Peng Li
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Corrosion Behavior ◽  
Current Density ◽  
Ion Beam ◽  
Electrochemical Corrosion ◽  
Corrosion Current ◽  
Open Circuit ◽  
Electrochemical Corrosion Behavior ◽  
Shot Number

HIPIB irradiation experiment is carried out at a specific ion current density of 1.1 J/cm2 with shot number from one to ten in order to explore the effect of shot number on electrochemical corrosion behavior of magnesium alloy. Surface morphologies, microstructure and corrosion resistance of the irradiated samples are examined by scanning electron microscopy (SEM), transmission electron microscope (TEM) and potentiodynamic polarization technique, respectively. It is found that HIPIB irradiation leads to the increase in open circuit potential, corrosion potential and breakdown potential, and the decrease in the corrosion current density and the corrosion rate as compared to the original sample. The improved corrosion resistance is mainly attributed to the grain refinement and surface purification induced by HIPIB irradiation.

scholarly journals STUDIES ON TENSILE PROPERTIES AT VARIOUS STRAIN RATES AND CORROSION BEHAVIOR OF PEAKAGED AL-6SI-0.5MG (-0.5CU) ALLOYS

2016 ◽  
Vol 17 (2) ◽  
pp. 105-115
Author(s):  
Abul Hossain ◽  
Fahmida Gulshan ◽  
A. S. W. Kurny
Keyword(s):  
Tensile Properties ◽  
Corrosion Behavior ◽  
Open Circuit Potential ◽  
Corrosion Potential ◽  
Electrochemical Corrosion ◽  
Open Circuit ◽  
Strain Rates ◽  
Cu Content ◽  
Electrochemical Corrosion Behavior ◽  
Experimental Strain

This paper focuses the effect of Cu additions on tensile properties of Al-6Si-0.5Mg alloy at various strain rates and electrochemical corrosion behavior. The additions of Cu resulted in an increase in tensile strength and showed higher strength all over the experimental strain rates. Evaluations of tensile properties at the three different strain rates (10-4, 10-3 & 10-2s-1) showed that they affected the tensile properties significantly. The strength was better at higher strain rate but ductility was poor. Eelectrochemical impedance spectroscopy (EIS) and potentiodynamic polarisation have been used to evaluate the corrosion resistance of Cu free and 0.5wt% Cu content Al-6Si-0.5Mg alloy in 0.1M NaCl solution. The 0.5wt% Cu addition to the Al-6Si-0.5Mg alloy showed that Cu decreased susceptibility to corrosion compared to the Cu free Al-6Si-0.5Mg alloy. The magnitude of open circuit potential (OCP), corrosion potential (Ecorr) and pitting corrosion potential (Epit) of Al-6Si-0.5Mg alloy were shifted to the more noble direction due to 0.5wt% Cu addition and thermal modification.

scholarly journals Effect of Iron Content on Corrosion Properties of Pure Titanium as Grain Refiner

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7193
Author(s):  
Bosung Seo ◽  
Hyeon-Tae Im ◽  
Ki-Beom Park ◽  
Kwangsuk Park ◽  
Hyung-Ki Park
Keyword(s):  
Corrosion Resistance ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Pure Titanium ◽  
Open Circuit ◽  
Tio2 Layer ◽  
Grain Refiner ◽  
Corrosion Properties ◽  
Acid Environment ◽  
Titanium Cathode

Microstructures and corrosion properties of pure titanium were characterized when iron was used as a grain refiner. The added Fe element acted as a strong grain refiner for pure titanium by forming β Ti phase at grain boundaries, and 0.15 wt% Fe was revealed to be a sufficient amount to make the grain size of pure titanium below 20 μm, which was the requirement for the desired titanium cathode. However, corrosion resistance was decreased with the Fe amount added. From the open circuit potential (OCP) results, it was obvious that the TiO2 stability against the reducing acid environment was deteriorated with the Fe amount, which seemed to be the main reason for the decreased corrosion resistance. Electrochemical impedance spectroscopy (EIS) results showed that both the decrease in the compact oxide film’s resistance (Rb) and the appearance of the outer porous film occurred as a result of the dissolution of the TiO2 layer, whose phenomena became more apparent as more Fe was added.

scholarly journals The Microstructure Evolution and Electrochemical Corrosion Behavior of 7A46 Aluminum Alloy in Different Quenching Conditions

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 477
Author(s):  
Yaru Liu ◽  
Lu Xing ◽  
Qing Zeng ◽  
Qinglin Pan ◽  
Sheng Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Electrochemical Impedance ◽  
Electrochemical Corrosion ◽  
Aged Alloy ◽  
Quench Sensitivity ◽  
Free Zone ◽  
The Matrix ◽  
Electrochemical Corrosion Behavior

The quenching condition of aluminum alloy can affect the mechanical property and corrosion resistance of the profile. This paper is aimed at the low quench sensitivity of aluminum alloys. Scanning electron microscopy and transmission electron microscopy were used to analyze precipitate behaviors of the 7A46 aluminum alloy under different isothermal cooling conditions and microstructure evolutions of quench-induced precipitations. The effect of the different isothermal time on the corrosion resistance of the alloy, and the relationship between microstructure and corrosion resistance after quenching were revealed through electrochemical impedance spectroscopy and potentiodynamic polarization tests. Results show that corrosion sensitivity of the quenching-aged alloy is much higher than that of the double-aged (DA) alloy, and the corrosion resistance of the quenched alloy decreases firstly and then increases. Due to the high density of the matrix precipitates, the increased content of the impurity element, the discontinuity of the grain boundary precipitates and the widening of the precipitates free zone, the most serious degree of corrosion performance among the quenched alloys is 295 °C at 800 s, and the self-corrosion potential and self-current density is −0.919 V and 2.371 μA/cm2, respectively.

Sign in / Sign up

Export Citation Format

Share Document