scholarly journals Controlled Synthesis of Hierarchically Assembled Porous ZnO Microspheres with Enhanced Gas-Sensing Properties

2015 ◽  
Vol 2015 ◽  
pp. 1-9
Author(s):  
Shengsheng You ◽  
Haojie Song ◽  
Jing Qian ◽  
Ya-li Sun ◽  
Xiao-hua Jia
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Hexagonal Phase ◽  
Trisodium Citrate ◽  
Zinc Hydroxide ◽  
Scanning Calorimetry ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Porous Nanosheets ◽  
Gas Sensing Properties

The ZnO microspheres constructed by porous nanosheets were successfully synthesized by calcinating zinc hydroxide carbonate (ZHC) microspheres obtained by a sample hydrothermal method. The samples were characterized in detail with scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and thermogravimetric and differential scanning calorimetry (TG-DSC). The results indicated that the prepared ZnO microspheres were well crystalline with wurtzite hexagonal phase. The effects of reaction time, temperature, the amount of trisodium citrate, and urea on the morphology of ZnO microspheres were studied. The formation mechanism of porous ZnO microspheres was discussed. Furthermore, the gas-sensing properties for detection of organic gas of the prepared porous ZnO microspheres were investigated. The results indicated that the prepared porous ZnO microspheres exhibited high gas-sensing properties for detection of ethanol gas.

Synthesis of Al Doped ZnO with a Novel Rice Microstructure by Hydrothermal Process and Analysis of their Gas Sensing Properties

2014 ◽  
Vol 809-810 ◽  
pp. 724-730
Author(s):  
Zan Li ◽  
Wei Qin ◽  
Xiao Hong Wu
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Hydrothermal Process ◽  
Hexagonal Wurtzite Structure ◽  
X Ray ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Doped Zno ◽  
Hydrothermal Approach

Al-doped ZnO (AZO) powers with a novel rice-like morphology have been successfully synthesized through a simple and efficient hydrothermal approach, the products have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) with an energy-dispersive X-ray analyzer and transmission electron microscopy (TEM). It showed that all the samples presented an hexagonal wurtzite structure of high crystallinity, and the microstructure was composed of numerous dumbbells. Furthermore, the heater gas sensors were fabricated and an investigation of gas sensing properties has been conducted. The sensors showed good selectivity to ethanol comparing with NH3, SO2, CO and HCHO and possible mechanism was discussed. The Sensors based AZO powers exhibited high response values, reproducible response-recovery to ethanol 50-1800 ppm at 332°C.

The Microwave-Assisted Synthesis and Gas Sensing Properties for Ethanol of SnO2 Nanomaterials

2013 ◽  
Vol 721 ◽  
pp. 237-240 ◽  
Author(s):  
Yong Ju Liu ◽  
Qiu Ping Jiang ◽  
Yue Huan Li ◽  
He Yun Zhao
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Microwave Assisted Synthesis ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Microwave Assisted ◽  
Transmission Electron ◽  
Good Crystalline Quality ◽  
Gas Sensing Properties ◽  
Microwave Assisted Method

With the advantages of the microwave-assisted method, good crystalline quality SnO2nanomaterials were successfully synthesized. The morphology and microstructure of SnO2were characterized by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy and high-resolution (HRTEM) used to examine SnO2nanomaterials. Indirect-heating sensors based on nanorods were fabricated and investigated for the gas sensing properties to ethanol. The investigation demonstrates that the sensor based on prepared SnO2nanomaterials has good sensitivity, low detection limit and short response and reversion time to ethanol at 275 °C.

The Characterization and Gas Sensing Properties of Polythiophene Coated V2O5 Nanotubes

2010 ◽  
Vol 654-656 ◽  
pp. 1154-1157 ◽  
Author(s):  
Yu Lu ◽  
Wei Jin ◽  
Wen Chen
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Higher Sensitivity

Polythiophene (PTP) coated V2O5 nanotubes were prepared by an in-situ polymerization of thiophene monomers in the presence of prepared V2O5 nanotubes. The nanotubes were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which proved the polymerization of thiophene monomer and the strong interaction between polythiophene and V2O5 nanotubes (VONTs). The gas sensing properties of PTP coated V2O5 nanotubes were studied at room temperature, which was found that PTP coated V2O5 nanotubes could detect ethanol with much higher sensitivity than pure VONTs. The sensing mechanism of PTP coated V2O5 nanotubes to ethanol is presumed to be the synergetic interaction between polythiophene (PTP) and V2O5 nanotubes.

scholarly journals Preparation and NH3 Gas-Sensing Properties of Double-Shelled Hollow ZnTiO3 Microrods

Sensors ◽  
2019 ◽  
Vol 20 (1) ◽  
pp. 46 ◽  
Author(s):  
Pi-Guey Su ◽  
Xiang-Hong Liu
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Gas Sensing ◽  
Strong Response ◽  
X Ray ◽  
Sensing Properties ◽  
Diallyldimethylammonium Chloride ◽  
Transmission Electron ◽  
Low Concentrations ◽  
Gas Sensing Properties

A novel double-shelled hollow (DSH) structure of ZnTiO3 microrods was prepared by self-templating route with the assistance of poly(diallyldimethylammonium chloride) (PDDA) in an ethylene glycol (EG) solution, which was followed by calcining. Moreover, the NH3 gas-sensing properties of the DSH ZnTiO3 microrods were studied at room temperature. The morphology and composition of DSH ZnTiO3 microrods films were analyzed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffractometry (XRD). The formation process of double-shelled hollow microrods was discussed in detail. The comparative gas-sensing results revealed that the DSH ZnTiO3 microrods had a higher response to NH3 gas at room temperature than those of the TiO2 solid microrods and DSH ZnTiO3 microrods did in the dark. More importantly, the DSH ZnTiO3 microrods exhibited a strong response to low concentrations of NH3 gas at room temperature.

Oxygen vacancies-contained SnO2 nanotubes with enhanced ethanol gas sensing properties

2019 ◽  
Vol 34 (01n03) ◽  
pp. 2040003 ◽  
Author(s):  
Yifan Chen ◽  
Xiuling Ma ◽  
Chen Li ◽  
Qiuyu Wu ◽  
Yongbo Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
High Performance ◽  
Oxygen Vacancies ◽  
Gas Sensing ◽  
Original Sample ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Ethanol Sensing

[Formula: see text] porous nanotubes containing oxygen vacancies were prepared by electron spinning and H plasma treatment. The morphology and crystal structure of the samples were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The ethanol-sensing properties of the [Formula: see text] sensor were tested. The results show that the samples treated with H plasma for 20 min have the best performance. Its working temperature is [Formula: see text]C lower than [Formula: see text]C of the original sample, with a sensitivity of 17 at 100 ppm, which is seven times higher than the original sample. It also shows good selectivity to some common interfering gases. This enhancement can be ascribed to the introduced oxygen vacancy. This work provides an efficient way to design high-performance gas sensor materials.

scholarly journals A comparative study on the electrical and gas sensing properties of thick films prepared with synthesized nano-sized and commercial micro-sized Fe2O3 powders

2017 ◽  
Vol 11 (4) ◽  
pp. 265-274 ◽  
Author(s):  
Ali Mirzaei ◽  
Maryam Bonyani ◽  
Shahab Torkian ◽  
Mahdi Feizpour ◽  
Anna Bonavita ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Thick Films ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Sensing Applications ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Underlying Mechanisms

In this work, Fe2O3 nanoparticles (NPs) were successfully synthesized by Pechini sol-gel method. Scanning electron microscopy, transmission electron microscopy and X-ray diffraction characterizations were used to study the morphology and crystal structure of the synthesized products. The electrical and gas sensing behaviour of the synthesized and commercial Fe2O3 samples, prepared in the form of thick films, were studied. Though the commercial Fe2O3 powders had lower resistance but it was found that the synthesized Fe2O3 NPs had better gas sensing properties. The underlying mechanisms are discussed in details. The present findings show advantages of Fe2O3 NPs over micro-size particles for gas sensing applications.

scholarly journals Gas Sensing Properties of Perovskite Decorated Graphene at Room Temperature

Sensors ◽  
2019 ◽  
Vol 19 (20) ◽  
pp. 4563 ◽  
Author(s):  
Juan Casanova-Cháfer ◽  
Rocío García-Aboal ◽  
Pedro Atienzar ◽  
Eduard Llobet
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Gas Sensing ◽  
Semiconductor Film ◽  
Promising Alternative ◽  
Sensing Properties ◽  
Enhanced Sensitivity ◽  
Transmission Electron ◽  
Gas Sensing Properties

This paper explores the gas sensing properties of graphene nanolayers decorated with lead halide perovskite (CH3NH3PbBr3) nanocrystals to detect toxic gases such as ammonia (NH3) and nitrogen dioxide (NO2). A chemical-sensitive semiconductor film based on graphene has been achieved, being decorated with CH3NH3PbBr3 perovskite (MAPbBr3) nanocrystals (NCs) synthesized, and characterized by several techniques, such as field emission scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. Reversible responses were obtained towards NO2 and NH3 at room temperature, demonstrating an enhanced sensitivity when the graphene is decorated by MAPbBr3 NCs. Furthermore, the effect of ambient moisture was extensively studied, showing that the use of perovskite NCs in gas sensors can become a promising alternative to other gas sensitive materials, due to the protective character of graphene, resulting from its high hydrophobicity. Besides, a gas sensing mechanism is proposed to understand the effects of MAPbBr3 sensing properties.

Polyaniline/SnO2 Nanocomposite Sensor for NO2 Gas Sensing at Low Operating Temperature

2015 ◽  
Vol 14 (04) ◽  
pp. 1550011 ◽  
Author(s):  
A. Sharma ◽  
M. Tomar ◽  
V. Gupta ◽  
A. Badola ◽  
N. Goswami
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
High Sensitivity ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Chemical Route ◽  
Sensing Properties ◽  
Response Recovery ◽  
Transmission Electron ◽  
Gas Sensing Properties

In this paper gas sensing properties of 0.5–3% polyaniline (PAni) doped SnO 2 thin films sensors prepared by chemical route have been studied towards the trace level detection of NO 2 gas. The structural, optical and surface morphological properties of the PAni doped SnO 2 thin films were investigated by performing X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Raman spectroscopy measurements. A good correlation has been identified between the microstructural and gas sensing properties of these prepared sensors. Out of these films, 1% PAni doped SnO 2 sensor showed high sensitivity towards NO 2 gas along with a sensitivity of 3.01 × 102 at 40°C for 10 ppm of gas. On exposure to NO 2 gas, resistance of all sensors increased to a large extent, even greater than three orders of magnitude. These changes in resistance upon removal of NO 2 gas are found to be reversible in nature and the prepared composite film sensors showed good sensitivity with relatively faster response/recovery speeds.

TUNGSTEN-DOPED TiO2 NANOLAYERS WITH IMPROVED CO2 GAS SENSING PROPERTIES FOR ENVIRONMENTAL APPLICATIONS

2017 ◽  
Vol 24 (Supp02) ◽  
pp. 1850024 ◽  
Author(s):  
MALIHEH SABERI ◽  
ALI AKBAR ASHKARRAN
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Sol Gel ◽  
Optimum Operating ◽  
Optimum Operating Temperature ◽  
Sensing Properties ◽  
Vis Spectroscopy ◽  
Gas Sensing Properties ◽  
Tungsten Concentration

Tungsten-doped TiO2 gas sensors were successfully synthesized using sol–gel process and spin coating technique. The fabricated sensor was characterized by field emission scanning electron microscopy (FE-SEM), ultraviolet visible (UV–Vis) spectroscopy, transmission electron microscopy (TEM), X-Ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. Gas sensing properties of pristine and tungsten-doped TiO2 nanolayers (NLs) were probed by detection of CO2 gas. A series of experiments were conducted in order to find the optimum operating temperature of the prepared sensors and also the optimum value of tungsten concentration in TiO2 matrix. It was found that introducing tungsten into the TiO2 matrix enhanced the gas sensing performance. The maximum response was found to be (1.37) for 0.001[Formula: see text]g tungsten-doped TiO2 NLs at 200[Formula: see text]C as an optimum operating temperature.

Sensing Properties of CNT hybrid MOS-based Sensors

2004 ◽  
Vol 828 ◽  
Author(s):  
Wei-Jen Liou ◽  
Tsung-Yeh Yang ◽  
Kuang-Nan Lin ◽  
Ching-Hong Yang ◽  
Hong-Ming Lin
Keyword(s):  
Electron Microscopy ◽  
Gas Adsorption ◽  
Gas Sensing ◽  
Sol Gel ◽  
Gas Sensitivity ◽  
Sensing Properties ◽  
Operation Temperature ◽  
Transmission Electron ◽  
Lower Temperature ◽  
P Type

ABSTRACTThe carbon nanotubes provide large surface that can enhance the gas adsorption properties and increase the conductivity at a lower temperature for gas sensing. The gas sensing properties of the hybrid TiO2/CNTs material are examined in this study. The sol-gel technique is used to prepare a thin layer of nano-TiO2 coated on CNTs. The structure of TiO2/CNTs hybrid materials is identified by X-ray diffraction (XRD) and Raman spectrum. The granules and surface morphology are analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrical properties of the hybrid TiO2/CNTs indicate that the operation temperature can be lowered to ambient temperature and this will enhance the gas sensitivity for detecting CO gas. The n-type or p-type behavior of hybrid TiO2/CNTs can be controlled by the coating thickness of hybrid TiO2. According to the image results, the mechanisms of the n-type and p-type behavior of hybrid TiO2/CNTs system are proposed.

Sign in / Sign up

Export Citation Format

Share Document