scholarly journals Design and Development of a Delta 3D Printer Using Salvaged E-Waste Materials

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Anthony Simons ◽  
Kossi L. M. Avegnon ◽  
Cyrus Addy
Keyword(s):  
3D Printing ◽  
Work Rate ◽  
Stepper Motor ◽  
3D Printer ◽  
Design And Development ◽  
The World ◽  
Stepper Motors ◽  
3D Printed ◽  
Design Calculations ◽  
Stable Linear

The next phase of industrialization in the world is the use of 3D printing technology. Various 3D printing technologies are employed all over the world and for different purposes, from 3D printed houses to 3D printed food nutrients. Printer movement is achieved by carriages moving in a clearly defined X, Y, and Z orientation. The 3D printer has a lower work rate; subsequently, many printouts consume a lot of time due to their complexity. This paper elaborates on the design and development of a faster and fixed build platform 3D printer (Delta 3D printer) using locally available materials and e-waste. The Delta 3D printer movement is faster with a stable bed. Printer movement is achieved using three vertical axes placed 120° apart. Accuracy and speed are achieved with the use of NEMA 17 stepper motors to drive the various carriages on the vertical axes. Design calculations show that the least force delivered by the stepper motor is 1.73 N which exceeds 0.8334 N, the weight of the load to be carried. Furthermore, a stepper motor must turn 80 steps (rotational motion) in order to achieve 1 mm advance (linear motion). This ensures a higher printout resolution. In place of traditional linear rails, locally sourced square pipes were adopted coupled with bearings and a 3D printed carriage support, and a relatively cheaper but stable linear rail was developed. The goal of this research was to develop an alternative easy-to-build Delta 3D printer using locally sourced materials. This goal of this research was achieved, and the developed prototype was test-run under load conditions. It is recommended that salvaged e-waste should be properly managed for easy acquisition.

scholarly journals Developement of 3D printer for silicate-based materials

2020 ◽  
Vol 2 (SI2) ◽  
pp. First
Author(s):  
Can Chi Trieu ◽  
Minh-Thien Nguyen ◽  
Thien-Toan Quan Le ◽  
Manh-Quyen Dam ◽  
Anh-Tu Tran ◽  
...  
Keyword(s):  
3D Printing ◽  
Manufacturing Industry ◽  
3D Printer ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Frame Element ◽  
Key Factor ◽  
Stepper Motors ◽  
Mach 3 ◽  
Near Future

3D printer and 3D printing technology are now considered as one of the key factor in the manufacturing industry. In the near future, we could envisage different application of 3D printing method in the sector of materials processing and production. In the sector of civil engineering, they existed somewhere some construction works developed with 3D printing technology.  In this study, we aim to manufacture laboratory-scale printers with nozzles and extrusion feeding systems suitable for paste such as the case of clay-based materials of silicate industry. The movement system was encoded and controlled via the motherboard (Mach 3 controller software). Stepper motors and shaft drives were also implemented in the frame element of such printer. The feeding system was designed based on the extrusion method including cylinder and piston element. Based on that, sample size 200x300x300mm was available for operation testing. Concerning the performance of the instrument, we have obtained printed specimens with different geometric shapes with complexity. From the obtained result, we also discussion on the feasibility up scaling the study and developing a 3D printer for silicate based materials.

A physical investigation of dimensional and mechanical characteristics of 3D printed nut and bolt for industrial applications

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ramesh Chand ◽  
Vishal S. Sharma ◽  
Rajeev Trehan ◽  
Munish Kumar Gupta
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
3D Printing ◽  
Surface Properties ◽  
3D Printer ◽  
Content Type ◽  
Safety Issues ◽  
Machine Failure ◽  
Sharp Edges ◽  
3D Printed

Purpose A nut bolt joint is a primary device that connects mechanical components. The vibrations cause bolted joints to self-loosen. Created by motors and engines, leading to machine failure, and there may be severe safety issues. All the safety issues and self-loosen are directly and indirectly the functions of the accuracy and precision of the fabricated nut and bolt. Recent advancements in three-dimensional (3D) printing technologies now allow for the production of intricate components. These may be used technologies such as 3D printed bolts to create fasteners. This paper aims to investigate dimensional precision, surface properties, mechanical properties and scanning electron microscope (SEM) of the component fabricated using a multi-jet 3D printer. Design/methodology/approach Multi-jet-based 3D printed nut-bolt is evaluated in this paper. More specifically, liquid polymer-based nut-bolt is fabricated in sections 1, 2 and 3 of the base plate. Five nuts and bolts are fabricated in these three sections. Findings Dimensional inquiry (bolt dimension, general dimensions’ density and surface roughness) and mechanical testing (shear strength of nut and bolt) were carried out throughout the study. According to the ISO 2768 requirements for the General Tolerances Grade, the nut and bolt’s dimensional examination (variation in bolt dimension, general dimensions) is within the tolerance grades. As a result, the multi-jet 3D printing (MJP)-based 3D printer described above may be used for commercial production. In terms of mechanical qualities, when the component placement moves from Sections 1 to 3, the density of the manufactured part decreases by 0.292% (percent) and the shear strength of the nut and bolt decreases by 30%. According to the SEM examination, the density of the River markings, sharp edges, holes and sharp edges increased from Sections 1 to 3, which supports the findings mentioned above. Originality/value Hence, this work enlightens the aspects causing time lag during the 3D printing in MJP. It causes variation in the dimensional deviation, surface properties and mechanical properties of the fabricated part, which needs to be explored.

Controlled Release of Bi-Layered Malvidin Tablets Using 3D Printing Techniques

2021 ◽  
pp. 70-78
Author(s):  
Tejinder Kaur ◽  
Suruchi Singh
Keyword(s):  
Controlled Release ◽  
3D Printing ◽  
Fruits And Vegetables ◽  
Physical And Mechanical Properties ◽  
3D Printer ◽  
Anti Cancer ◽  
Printing Cost ◽  
3D Printed ◽  
Cost Efficient ◽  
3D Printing Technique

Malvidin belongs to the class of anthocyanidin, a pigment compound present in fruits and vegetables like the colored berries, flowers, and vegetables which have pigments on it and it is available commercially as malvidin chloride. Malvidin is known to possess many medicinal characteristics like anti-microbial, anti-diabetic, anti-inflammatory, anti-obesity, and anti-cancer. In this research paper, a 3D printing technique is used which evolves a 3D printer based on desktop that extrudes tablets comprising the active drug which here is malvidin our main ingredient and the other excipients which are used as binders and disintegrants. Methods which are adapted here for the formulation of 3D printed tablet make the tablets appropriate for immediate and sustained release with its definite physical and mechanical properties like hardness, friability, and weight. Tablets that are extruded by the 3D printer are controlled release bi-layer tablets. Due to involvement of 3D printer, printing cost for the bi-layered tablets found very low that makes our method as cost efficient.

History of Additive Manufacturing

2017 ◽  
pp. 1-24 ◽  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Large Scale ◽  
Selective Laser Sintering ◽  
3D Printer ◽  
3D Objects ◽  
History Of ◽  
Pros And Cons ◽  
3D Printed ◽  
The Common

History of additive manufacturing started in the 1980s in Japan. Stereolithography was invented first in 1983. After that tens of other techniques were invented under the common name 3D printing. When stereolithography was invented rapid prototyping did not exists. Tree years later new technique was invented: selective laser sintering (SLS). First commercial SLS was in 1990. At the end of 20t century, first bio-printer was developed. Using bio materials, first kidney was 3D printed. Ten years later, first 3D Printer in the kit was launched to the market. Today we have large scale printers that printed large 3D objects such are cars. 3D printing will be used for printing everything everywhere. List of pros and cons questions rising every day.

Design and Development of 3D Printed Teaching Aids for Architecture Education

2019 ◽  
pp. 457-475
Author(s):  
Min Jeong Song ◽  
Euna Ha ◽  
Sang-Kwon Goo ◽  
JaeKyung Cho
Keyword(s):  
3D Printing ◽  
3D Modeling ◽  
3D Models ◽  
Design And Development ◽  
Architecture Education ◽  
Teaching Aids ◽  
Current State ◽  
Practice Based Research ◽  
Research Findings ◽  
3D Printed

This article describes how the implementation of 3D printing in classrooms has brought many opportunities to educators as it provides affordability and accessibility in creating and customizing teaching aids. The study reports on the process of fabricating teaching aids for architecture education using 3D printing technologies. The practice-based research intended to illustrate the making process from initial planning, 3D modeling to 3D printing with practical examples, and addresses the potential induced by the technologies. Based on the investigation into the current state of 3D printing technologies in education, limitations were identified before the making process. The researchers created 3D models in both digital and tangible forms and the process was documented in textual and pictorial formats. It is expected that the research findings will serve as a guideline for other educators to create 3D printed teaching aids, particularly architectural forms.

scholarly journals Three-dimensional Printing Versus Conventional Machining in the Creation of a Meatal Urethral Dilator: a Cost and Mechanical Strength Analysis

2020 ◽  
Author(s):  
Michael Yue-Cheng Chen ◽  
Jacob Skewes ◽  
Ryan Daley ◽  
Maria Ann Woodruff ◽  
Nicholas John Rukin
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Strength Analysis ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Current Time ◽  
Fused Deposition ◽  
3D Printed ◽  
Conventional Machining

Abstract BackgroundThree-dimensional (3D) printing is a promising technology but the limitations are often poorly understood. We compare different 3D printingmethods with conventional machining techniques in manufacturing meatal urethral dilators which were recently removed from the Australian market. MethodsA prototype dilator was 3D printed vertically orientated on a low cost fused deposition modelling (FDM) 3D printer in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). It was also 3D printed horizontally orientated in ABS on a high-end FDM 3D printer with soluble support material, as well as on a SLS 3D printer in medical nylon. The dilator was also machined in stainless steel using a lathe. All dilators were tested mechanically in a custom rig by hanging calibrated weights from the handle until the dilator snapped. ResultsThe horizontally printed ABS dilator experienced failure at a greater load than the vertically printed PLA and ABS dilators respectively (503g vs 283g vs 163g, p < 0.001). The SLS nylon dilator and machined steel dilator did not fail. The steel dilator is most expensive with a quantity of five at 98 USD each, but this decreases to 30 USD each for a quantity of 1000. In contrast, the cost for the SLS dilator is 33 USD each for five and 27 USD each for 1000. ConclusionsAt the current time 3D printing is not a replacement for conventional manufacturing. 3D printing is best used for patient-specific parts, prototyping or manufacturing complex parts that have additional functionality that cannot otherwise beachieved.

scholarly journals Property Analysis of Photo-Polymerization-Type 3D-Printed Structures Based on Multi-Composite Materials

2021 ◽  
Vol 11 (18) ◽  
pp. 8545
Author(s):  
So-Ree Hwang ◽  
Min-Soo Park
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Composite Materials ◽  
3D Printing ◽  
Bending Test ◽  
3D Printer ◽  
Complex Structures ◽  
Photo Polymerization ◽  
Anisotropic Structures ◽  
3D Printed

Additive manufacturing, commonly called 3D printing, has been studied extensively because it can be used to fabricate complex structures; however, polymer-based 3D printing has limitations in terms of implementing certain functionalities, so it is limited in the production of conceptual prototypes. As such, polymer-based composites and multi-material 3D printing are being studied as alternatives. In this study, a DLP 3D printer capable of printing multiple composite materials was fabricated using a movable separator and structures with various properties were fabricated by selectively printing two composite materials. After the specimen was fabricated based on the ASTM, the basic mechanical properties of the structure were compared through a 3-point bending test and a ball rebound test. Through this, it was shown that structures with various mechanical properties can be fabricated using the proposed movable-separator-based DLP process. In addition, it was shown that this process can be used to fabricate anisotropic structures, whose properties vary depending on the direction of the force applied to the structure. By fabricating multi-joint grippers with varying levels of flexibility, it was shown that the proposed process can be applied in the fabrication of soft robots as well.

Combinatorial Investigation of Mechanical Properties of Biomimicked Composites

2019 ◽  
Author(s):  
Seyed M. Allameh ◽  
Roger Miller ◽  
Abdullah Almuzaini
Keyword(s):  
3D Printing ◽  
Construction Industry ◽  
Construction Materials ◽  
3D Printer ◽  
In Situ Tests ◽  
Art Economics ◽  
Materials Research ◽  
3D Printed ◽  
Combinatorial Materials

Abstract This study presents the preliminary results of in-situ tests conducted on structural biomimicked composites built by 3D printing. Construction industry is looking seriously into 3D printed structures that can be incorporated into the conventional buildings. Further refinement of materials and processing will lead to the 3D printing of buildings in future. The advantages afforded by 3D printing are unrivaled, creating unprecedented opportunities to express art, economics, environmentally friendly designs, lightweight schemes, among many others. To determine the reliability and suitability of structural composites for use in construction, it is important to test these in shapes, and geometries that are appropriate to 3D printing. Combinatorial materials research allows the fabrication and in-situ testing of composites made by mix and match of various materials. This study focuses on the characterization of mechanical behavior of biomimicked composites fabricated by a 3D printer. To accomplish this, a meter-sized 3D printer was equipped with material dispensers as well as load sensors. Composites were made of various construction materials, adhesive, and reinforcement and subsequently tested by the same printer. The results are presented, and the implications of findings are discussed on their impact on the construction industry.

An overview on joining/welding as post-processing technique to circumvent the build volume limitation of an FDM-3D printer

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Vivek Kumar Tiwary ◽  
Arunkumar P. ◽  
Vinayak R. Malik
Keyword(s):  
3D Printing ◽  
Literature Review ◽  
Adhesive Bonding ◽  
Business Leaders ◽  
Future Research ◽  
3D Printer ◽  
Content Type ◽  
Friction Stir ◽  
Fused Deposition ◽  
3D Printed

Purpose Three-dimensional (3D) printing, one of the important technological pillars of Industry 4.0, is changing the landscape of future manufacturing. However, the limited build volume of a commercially available 3D printer is one inherent constraint, which holds its acceptability by the manufacturing business leaders. This paper aims to address the issue by presenting a novel classification of the possible ways by which 3D-printed parts can be joined or welded to achieve a bigger-sized component. Design/methodology/approach A two-step literature review is performed. The first section deals with the past and present research studies related to adhesive bonding, mechanical interlocking, fastening and big area additive manufacturing of 3D printed thermoplastics. In the second section, the literature searches were focused on retrieving details related to the welding of 3D printed parts, specifically related to friction stir welding, friction (spin) welding, microwave and ultrasonic welding. Findings The key findings of this review study comprise the present up-to-date research developments, pros, cons, critical challenges and the future research directions related to each of the joining/welding techniques. After reading this study, a better understanding of how and which joining/welding technique to be applied to obtain a bigger volume 3D printed component will be acquired. Practical implications The study provides a realistic approach for the joining of 3D printed parts made by the fused deposition modeling (FDM) technique. Originality/value This is the first literature review related to joining or welding of FDM-3D printed parts helping the 3D printing fraternity and researchers, thus increasing the acceptability of low-cost FDM printers by the manufacturing business leaders.

Design for the Controller of Desktop 3D Printer

2014 ◽  
Vol 672-674 ◽  
pp. 894-897
Author(s):  
Ruo Dong Huang ◽  
Xin Wang ◽  
Yi Hui Zheng ◽  
Li Xue Li ◽  
Xi Kui Sheng ◽  
...  
Keyword(s):  
3D Printing ◽  
Software Design ◽  
Stepper Motor ◽  
3D Printer ◽  
Layer By Layer ◽  
The Core ◽  
Whole Process ◽  
Materials Used ◽  
Avr Microcontroller ◽  
Rapid Prototyping Manufacturing

3D printing, is a kind of rapid prototyping manufacturing, fabricating expected objects by way of cumulative constructed layer by layer, based on digital model files and powdered materials used. In this paper, the controller of desktop 3D printer is designed and carried out, both from the hardware and software part. For hardware design, a 32-bit ARM core microcontroller, STM32F103VB is selected as the core, supplemented by stepper motor driver chips, thermocouple digital converters and other devices, which build a desktop 3D printer controller panel. For software design, referred to open-source design being based on the AVR microcontroller, the whole process of 3D printing is accomplished by programming the ARM core microcontroller.

Sign in / Sign up

Export Citation Format

Share Document