scholarly journals Experimental Investigation of the Mechanical Behavior of NC Linings in consideration of Voids and Lining Thinning

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Zude Ding ◽  
Jincheng Wen ◽  
Xiafei Ji ◽  
Zhihua Ren ◽  
Sen Zhang
Keyword(s):  
Mechanical Behavior ◽  
Local Deformation ◽  
Scale Model ◽  
Test Results ◽  
Load Bearing Capacity ◽  
Normal Concrete ◽  
Failure Characteristics ◽  
Defect Position ◽  
Deformation Properties ◽  
Combined Defects

The presence of voids or lining thinning directly affects the mechanical behavior of linings, and these defects threaten the safety of tunnel operation. In this study, a series of 1/5-scale model tests was used to investigate the mechanical behavior of normal concrete (NC) linings in consideration of voids and combined defects. Test results showed that the void and combined defects substantially reduced the load-bearing capacity and deformation properties of the linings. The inelastic mechanical behavior of the linings was also significantly affected by the defects. The effects of lining defects located at the spandrel were slightly weaker than those of lining defects located at the crown. As the void size or degree of combined defects increased, the tensile strain at the location of the lining defects also increased. Therefore, the defect position of the linings was easily damaged. The defects considerably reduced the overall deformation of the linings but increased the local deformation. The distribution of lining cracks was concentrated at the defect position. In addition, different failure characteristics of the lining were observed due to the differences in defects.

scholarly journals Influence of Existing Defects on Mechanical Properties of NC Lining

2019 ◽  
Vol 2019 ◽  
pp. 1-15
Author(s):  
Sen Zhang ◽  
Zhihua Ren ◽  
Zude Ding ◽  
Jincheng Wen ◽  
Zhixin Yan
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Bearing Capacity ◽  
Safety Evaluation ◽  
Scale Model ◽  
Concrete Lining ◽  
Displacement Curve ◽  
Deformation Properties ◽  
S Curve ◽  
Combined Defects

The mechanical properties of the lining are directly affected by defects such as voids behind the lining and insufficient thickness of the lining. In order to quantitatively evaluate this effect, the mechanical behavior of the lining under the influence of the void behind the lining, the insufficient thickness of the lining, and the combination of the two kinds of defects are adopted by the 1/5 scale model test. Based on the experimental research, numerical calculation models based on the CDP model for defect lining are established, with the effects of load direction, stratum stiffness, defect location, defect type, and degree on the mechanical behavior of the lining analyzed by the numerical simulation. The experimental and numerical results show that the void weakens the stiffness of the lining. As the void range increases, the lining becomes more deformable and its bearing capacity decreases with the “S” curve. Thinning significantly reduces the deformation properties of the lining and the bearing capacity and stiffness of the thinned section. The lining bearing capacity decreases linearly with the increase of the thinning ratio, when the load is applied at the thinning. With the influence of combined defects on the load-displacement curve of the lining fluctuating drastically, the mechanical properties of the lining are significantly reduced. The bearing capacity of lining decreases with the increase of composite defects in a “S” shape. The effect of void and lining thinning on the lining bearing capacity increases with the increase of the stiffness of the formation. The loss rate equation of the concrete lining bearing capacity under the influence of existing defects is established by using the L-M nonlinear regression analysis, a provision of scientific guidance for the safety evaluation of the defect lining.

Variasi Penambahan Sika Cim Dan Fiber Kawat Pada Beton Mutu Fc’ 30 Mpa

2018 ◽  
Vol 9 (2) ◽  
pp. 67-73
Author(s):  
M Zainul Arifin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Astm Method ◽  
Additive Type ◽  
Composition Variation ◽  
Compressive Strength Of Concrete

This research was conducted to determine the value of the highest compressive strength from the ratio of normal concrete to normal concrete plus additive types of Sika Cim with a composition variation of 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1 , 50% and 1.75% of the weight of cement besides that in this study also aims to find the highest tensile strength from the ratio of normal concrete to normal concrete in the mixture of sika cim composition at the highest compressive strength above and after that added fiber wire with a size diameter of 1 mm in length 100 mm with a ratio of 1% of material weight. The concrete mix plan was calculated using the ASTM method, the matrial composition of the normal concrete mixture as follows, 314 kg / m3 cement, 789 kg / m3 sand, 1125 kg / m3 gravel and 189 liters / m3 of water at 10 cm slump, then normal concrete added variations of the composition of sika cim 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.5%, 1.75% by weight of cement and fiber, the tests carried out were compressive strength of concrete and tensile strength of concrete, normal maintenance is soaked in fresh water for 28 days at 30oC. From the test results it was found that the normal concrete compressive strength at the age of 28 days was fc1 30 Mpa, the variation in the addition of the sika cim additive type mineral was achieved in composition 0.75% of the cement weight of fc1 40.2 Mpa 30C. Besides that the tensile strength test results were 28 days old with the addition of 1% fiber wire mineral to the weight of the material at a curing temperature of 30oC of 7.5%.

scholarly journals Investigation of the Time Dependence of Wind-Induced Aeroelastic Response on a Scale Model of a High-Rise Building

2021 ◽  
Vol 11 (8) ◽  
pp. 3315
Author(s):  
Fabio Rizzo
Keyword(s):  
Wind Tunnel ◽  
Time Dependence ◽  
Wind Tunnel Test ◽  
Structural Response ◽  
Cumulative Distribution ◽  
Scale Model ◽  
Acquisition Time ◽  
Test Results ◽  
High Rise ◽  
High Rise Building

Experimental wind tunnel test results are affected by acquisition times because extreme pressure peak statistics depend on the length of acquisition records. This is also true for dynamic tests on aeroelastic models where the structural response of the scale model is affected by aerodynamic damping and by random vortex shedding. This paper investigates the acquisition time dependence of linear transformation through singular value decomposition (SVD) and its correlation with floor accelerometric signals acquired during wind tunnel aeroelastic testing of a scale model high-rise building. Particular attention was given to the variability of eigenvectors, singular values and the correlation coefficient for two wind angles and thirteen different wind velocities. The cumulative distribution function of empirical magnitudes was fitted with numerical cumulative density function (CDF). Kolmogorov–Smirnov test results are also discussed.

Strengthening of reinforced concrete corbels with GFRP overlays

2011 ◽  
Vol 18 (1-2) ◽  
pp. 69-77 ◽  
Author(s):  
Sevket Ozden ◽  
Hilal Meydanli Atalay
Keyword(s):  
Reinforced Concrete ◽  
Reinforcement Ratio ◽  
Fiber Reinforced Polymer ◽  
Peak Performance ◽  
Test Results ◽  
Loading Test ◽  
Load Bearing Capacity ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Normal Strength

AbstractThe strength and post-peak performance of reinforced concrete corbels, strengthened with epoxy bonded glass fiber reinforced polymer (GFRP) overlays, were experimentally investigated. The test variables were the corbel shear span to depth ratio, corbel main reinforcement ratio, and the number and orientation of the GFRP fibers. In total, 24 normal strength concrete, one-third scale, corbel specimens, without hoop reinforcement, were tested to failure under quasi-static gravity loading. Test results revealed that GFRP overlays can easily be used for the enhancement of corbel load bearing capacity, depending on the fiber orientation. The main reinforcement ratio and the number of GFRP plies were found to be the two main variables affecting the level of strength gain in the corbel specimens.

Benchmarking of Truss Spar Vortex Induced Motions Derived From CFD With Experiments

2005 ◽  
Author(s):  
John Halkyard ◽  
Senu Sirnivas ◽  
Samuel Holmes ◽  
Yiannis Constantinides ◽  
Owen H. Oakley ◽  
...  
Keyword(s):  
Scale Up ◽  
Vertical Cylinder ◽  
Reynolds Numbers ◽  
Full Scale ◽  
Scale Model ◽  
Current Direction ◽  
Test Results ◽  
Helical Strakes ◽  
Truss Spar ◽  
Scale Data

Floating spar platforms are widely used in the Gulf of Mexico for oil production. The spar is a bluff, vertical cylinder which is subject to Vortex Induced Motions (VIM) when current velocities exceed a few knots. All spars to date have been constructed with helical strakes to mitigate VIM in order to reduce the loads on the risers and moorings. Model tests have indicated that the effectiveness of these strakes is influenced greatly by details of their design, by appurtenances placed on the outside of the hull and by current direction. At this time there is limited full scale data to validate the model test results and little understanding of the mechanisms at work in strake performance. The authors have been investigating the use of CFD as a means for predicting full scale VIM performance and for facilitating the design of spars for reduced VIM. This paper reports on the results of a study to benchmark the CFD results for a truss spar with a set of model experiments carried out in a towing tank. The focus is on the effect of current direction, reduced velocity and strake pitch on the VIM response. The tests were carried out on a 1:40 scale model of an actual truss spar design, and all computations were carried out at model scale. Future study will consider the effect of external appurtenances on the hull and scale-up to full scale Reynolds’ numbers on the results.

scholarly journals Tests and Analyses of Slotted-In Steel-Plate Connections in Composite Timber Shear Wall Panels

2017 ◽  
Vol 2017 ◽  
pp. 1-20
Author(s):  
Ulf Arne Girhammar ◽  
Bo Källsner
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Design Method ◽  
Shear Walls ◽  
Test Results ◽  
Horizontal Shear ◽  
Load Bearing Capacity ◽  
Wood Panel ◽  
Load Bearing ◽  
Plate Connections

The authors present an experimental and analytical study of slotted-in connections for joining walls in the Masonite flexible building (MFB) system. These connections are used for splicing wall elements and for tying down uplifting forces and resisting horizontal shear forces in stabilizing walls. The connection plates are inserted in a perimeter slot in the PlyBoard™ panel (a composite laminated wood panel) and fixed mechanically with screw fasteners. The load-bearing capacity of the slotted-in connection is determined experimentally and derived analytically for different failure modes. The test results show ductile postpeak load-slip characteristics, indicating that a plastic design method can be applied to calculate the horizontal load-bearing capacity of this type of shear walls.

scholarly journals Seismic Behavior and Force-Displacement Characterization of Neotype Column-Slab High Piers

2014 ◽  
Vol 2014 ◽  
pp. 1-10
Author(s):  
YanQun Zhou ◽  
YeZhi Zhang ◽  
MeiXin Ye ◽  
MengSi Zhan
Keyword(s):  
Seismic Behavior ◽  
Large Scale ◽  
Scale Model ◽  
Test Results ◽  
Lateral Displacements ◽  
High Pier ◽  
Experimental Values ◽  
Large Scale Tests ◽  
Force Displacement

The seismic behavior and plasticity spreading of a neotype column-slab high pier are researched in this paper. Four scale model tests of a web slab with two boundary columns are carried out under cyclic inelastic lateral displacements simulating seismic response. The test results show that the neotype column-slab high pier has strong and stable bearing capacity, good ductility, and energy dissipation capacity. The experimental values pertaining to the spread of plasticity are derived. An approach for deriving the spread of plasticity analytically is deduced and applied to the four tests. This method accurately assesses a pier’s spread of plasticity for most ductility levels. At nearly all ductility levels, the mean difference between analytical assessments of the spread of plasticity and results from 4 large-scale tests is 12% with a 9% coefficient of variation.

Experimental Study on Mechanical Behavior of Cold-Formed Steel Three Limbs Built-up Section Members

2010 ◽  
Vol 163-167 ◽  
pp. 651-654
Author(s):  
Tian Hua Zhou ◽  
Shao Feng Nie ◽  
Xiang Bin Liu ◽  
Guang Yi Li
Keyword(s):  
Experimental Study ◽  
Mechanical Behavior ◽  
Axial Compression ◽  
Local Buckling ◽  
Distortional Buckling ◽  
Torsional Buckling ◽  
Failure Characteristics ◽  
Compression Load ◽  
Cold Formed Steel ◽  
Flexural Torsional Buckling

18 specimens of cold-formed steel three limbs built-up section members are tested under axial compression load in this paper. The section forms are divided into two categories: A and B. Load-displacement (P-Δ) curves and failure characteristics of specimens are obtained. The results show that: As to section A members, the failure characteristics of LC, MC and SC series of specimens are flexural-torsional buckling, torsional buckling and distortional buckling, local buckling and distortional buckling. As to section B members, the failure characteristics of LC, MC series of specimens are flexural buckling, while local buckling and distortional buckling for members of SC series.

The Fatigue Performance of High Performance Concrete Composite Girder

2019 ◽  
Author(s):  
C. Xu ◽  
B. Y. Zhang ◽  
Z. H. Hou
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Test Results ◽  
Normal Concrete ◽  
Bending Tests ◽  
Composite Girder ◽  
Tensile Performance ◽  
Negative Bending ◽  
The One ◽  
Push Out

<p>The application of high performance concrete has been increasingly concerned in the negative flexural region of steel‐concrete continuous composite girder because of its favorable tensile performance. However, the unclear cyclic and ultimate performance of a high performance concrete composite girder results to the problems which hinder the further application. In this case, a series of fatigue negative bending tests on HPC composite girders and fatigue push‐out tests on stud connectors in HPC were executed. The test results showed that the fatigue slip in the HPC composite girder was smaller than the normal concrete composite girder, and the fatigue life of stud in HPC was longer than the one in normal concrete. Meanwhile, according to the comparison between the stud fatigue live evaluations and test results, the AASHTO‐based evaluations were comparatively with larger safety redundancy, and JSCE was close to the test results but had smaller safety redundancy.</p>

Deformation, Mechanical Properties, and Fracture of Quenched and Tempered Carbon Steels

2015 ◽  
pp. 405-437
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Ductile Fracture ◽  
Carbon Steels ◽  
Low Carbon ◽  
Tempering Temperature ◽  
Medium Carbon ◽  
Low Carbon Steels ◽  
Deformation Properties ◽  
Medium Carbon Steels

Abstract Steels with martensitic and tempered martensitic microstructures, though sometimes perceived as brittle, exhibit plasticity and ductile fracture behavior under certain conditions. This chapter describes the alloying and tempering conditions that produce a ductile form of martensite in low-carbon steels. It also discusses the effect of tempering temperature on the mechanical behavior and deformation properties of medium-carbon steels.

Sign in / Sign up

Export Citation Format

Share Document