scholarly journals Analysis on different shape of textile antenna under bending condition for GPS application

2020 ◽  
Vol 9 (5) ◽  
pp. 1964-1970
Author(s):  
N. I. Zaidi ◽  
M. T. Ali ◽  
N. H. Abd Rahman ◽  
M. F. Yahya ◽  
M. S. Amin Nordin
Keyword(s):  
Resonant Frequency ◽  
Radiation Pattern ◽  
Antenna Gain ◽  
Bending Angle ◽  
Antenna Performance ◽  
Textile Antenna ◽  
Human Arm ◽  
Different Shapes ◽  
Antenna Characteristics

In this paper, three antennas with different designs, which are square, circle and edgy patch (flower) were simulated and fabricated. The experiment was carried out to study the effects of bending on these three different shapes of antennas. Two bending conditions which are H-plane and E-plane were used. The antenna was designed to resonate at 1.575 GHz for GPS application and to be incorporated with human arm. Thus, the bending angle was specified to be 135o which is about the size of a typical human arm. As the paper focusing on the bending effects only, the characteristic of the bending structure was set to be equal to the air, with Ɛr=1. The antenna characteristics such as gain, resonant frequency and radiation pattern were analyzed for these three shapes of antennas. As a result, the shape of the radiating patch has significant impact on the antenna performance under bending conditions. Based on the comparison of E-plane and H-plane data, the edgy shape was found to be more affected in term of gain performance as compared to other shapes. Bending on E-plane has shown severe degradation in antenna gain performance, whereby at H-plane, significant improvement in gain was observed

Qualification of Polyimide Based Coverlays for 900 MHz and 2.40 GHz Microstrip Antenna Applications

2012 ◽  
Vol 2012 (1) ◽  
pp. 001078-001080
Author(s):  
Deepukumar Nair ◽  
Glenn Oliver ◽  
Jim Parisi
Keyword(s):  
Resonant Frequency ◽  
Radiation Pattern ◽  
Microstrip Antenna ◽  
Microstrip Antennas ◽  
Frequency Detuning ◽  
Antenna Gain ◽  
Test Vehicle ◽  
Minimal Impact ◽  
Frequency Bands

Organic coverlays are required to protect microstrip circuits in most applications. The presence of coverlay can potentially influence the performance of microstrip antennas. This paper describes the qualification of polyimide based coverlays for microstrip antennas both in 900 MHz and 2.50 GHz frequency bands. An Inverted F-shaped antenna fabricated on FR-4 dielectric is used as the test vehicle and two different coverlay materials are tested with respect to key parameters like resonant frequency, S11 bandwidth, antenna gain, frequency detuning, and radiation pattern. The data presented in this paper clearly indicates polyimide materials are well suited to cover microstrip antenna circuits with minimal impact on performance.

A Jawbreaker-Shaped Fragmentary Ground Textile Flexible Antenna

2020 ◽  
Vol 9 (2) ◽  
pp. 17-29
Author(s):  
Anurag Saxena ◽  
Vinod Kumar Singh ◽  
Akanksha Lohia ◽  
Mohd Faisal
Keyword(s):  
Resonant Frequency ◽  
Radiation Pattern ◽  
Satellite Communication ◽  
High Efficiency ◽  
Security System ◽  
Communication Security ◽  
Textile Antenna ◽  
Flexible Antenna

Under this article, a jawbreaker-shaped textile antenna is designed for assortment applications like satellite communication, security system, medical, etc. For the antenna to be wearable, jeans substrate is used in place of FR-4 material so that it can easily bend. After simulating in CST software, the resonant frequency is 7.5 GHz under which it covers the range of 5.37 GHz to 8.36 GHz frequency. The simulating result of proposed antenna shows high efficiency, better directivity, and radiation pattern. The overall bandwidth of proposed antenna is 27.07%.

scholarly journals Electrical Conductivity and Antenna Properties of Polyaniline filled GNPs Nanocomposites

2021 ◽  
Vol 4 (1) ◽  
pp. 11-27
Author(s):  
Jeefferie Abd Razak ◽  
Nor Aisah Khalid ◽  
Hazman Hasib ◽  
Mazlin Aida Mahamood ◽  
Mohd Muzafar Ismail ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Radiation Pattern ◽  
Cotton Fabric ◽  
Carrier Transport ◽  
Return Loss ◽  
Conductive Polymer ◽  
Polymer Nanocomposite ◽  
Antenna Gain ◽  
Textile Antenna ◽  
Aniline Polymerization

This study was conducted to investigate the potential of utilizing conductive polymer nanocomposite for flexible type antenna application. The polyaniline (PANI) filled with graphene nanoplatelets (GNPs) nanocomposites were synthesized by an oxidative aniline polymerization in an acidic medium. The PANI/GNPs nanocomposites were then characterized by using various spectroscopy and imaging tools. It was found that the strong interaction between PANI macromolecules and GNPs flakes is caused by the strong ?-? conjugation between them, as validated by an increase of Id/Ig ratio of PANI/GNPs nanocomposites. As a result, it established a three-fold improvement for the electrical conductivity of PANI/GNPs nanocomposites, due to the larger amount of charge carrier transport at higher GNPs nanofiller loadings (1.00 wt.%). Later, the PANI/GNPs nanocomposites powder was applied to the cotton fabric by integrating it with a rubber paint slurry. Electrical conductivity, antenna gain, return loss, and radiation pattern of the antenna were reported. It was found that PANI/GNPs flexible textile antenna possessed a constant gain of 4.1809 dB, return loss at -13.154 dB, and radiation pattern which operated at 10.36 GHz for 100% improvement of electrical conductivity, in comparison with unfilled PANI. From these findings, it can be said that the development of wearable textile antenna utilizing PANI/GNPs nanocomposites on the cotton fabric as flexible radiation patch, has great potential for wireless communication purposes.

scholarly journals RECONFIGURABLE MONOPOLE ANTENNA DESIGN BASED ON FRACTAL STRUCTURE FOR 5G APPLICATIONS

2021 ◽  
Vol 1 (1) ◽  
pp. 177-186
Author(s):  
Amna S. Kamel ◽  
Ali S. Jalal
Keyword(s):  
Resonant Frequency ◽  
Radiation Pattern ◽  
Fractal Structure ◽  
Ground Plane ◽  
Monopole Antenna ◽  
Antenna Design ◽  
Pin Diodes ◽  
Antenna Performance ◽  
Design Structure ◽  
Specific Direction

 a reconfigurable antenna design for 5G applications is presented. It is based on monopole antenna and fractal structure. The design structure is consisted of (monopole) feedline, ground plane, L-shape reflector, fractal structure and PIN diodes. The antenna is printed on (25×29×1.6 mm3) FR-4 substrate of εr=4.3 and tanδ =0.001. The antenna shows a resonant frequency at 4.1 GHz with S11=-11.4 dB and Omni-direction pattern of 1.21 dB gain. The L-shaped reflector is used to maintain the radiation pattern in a specific direction. Moreover, the proposed fractal structure is found to operate as a circuit to give another resonant frequency and enhance the antenna performance. Where it is used to give more manipulation in the antenna performance including: frequency resonance and radiation patterns. The PIN-diodes are used to give many cases for more current manipulation. moreover, the authors used RF (50 SMA port) between monopole antenna and right side of ground plane to optimize directing radiation pattern and to eliminate the problems of interference between AC and DC current that produced from using PIN diode. This manipulation leads to change the resonant frequency and radiation pattern to the desired direction.So all parts are printed on a single side of FR4 substrate

Perbandingan Desain Antena Dipole dan Yagi-Uda Menggunakan Material Aluminium pada Frekuensi 470 – 890 MHz

2017 ◽  
Vol 3 (3) ◽  
pp. 140
Author(s):  
Suci Rahmatia ◽  
Putri Wulandari ◽  
Nurul Khadiko ◽  
Fitria Gani Sulistya
Keyword(s):  
Radiation Pattern ◽  
Daily Activity ◽  
Dipole Antenna ◽  
Antenna Gain ◽  
Communication Tool ◽  
Dipole Antennas ◽  
Gain Bandwidth ◽  
Large Gain ◽  
At Home

<p><em>Abstrak </em><strong> - Antena merupakan alat pemancar yang akrab dengan aktifitas sehari-hari dan mudah sekali dijumpai, di rumah, di gedung, bahkan pada alat komunikasi yang digunakan. Salah satu antena yang sering digunakan adalah antena televisi. Antena televisi yang sering digunakan adalah Yagi-Uda yang biasanya dipakai sebagai outdoor antena dan antena dipole yang biasanya digunakan untuk indoor antena. Masing – masing jenis antena memiliki kriteria dan keuntungan berdasarkan dari kebutuhan penggunaannya. Baik antena dipole maupun antena Yagi-Uda memiliki perbedaan diantaranya adalah besar bandwidth, nilai gain, dan pola radiasi. Pada paper ini dapat diketahui bahwa bandwidth yang dimiliki antena yagi-uda lebih besar daripada antena dipole yakni 0.39943 MHz untuk antena yagi-uda dan 0.16569 MHz untuk antena dipole. Begitupula dengan besar Gain yang dimiliki antena Yagi-Uda (6.64 dBi) lebih besar dibandingkan dengan gain dari antena dipole (2.29 dBi). Perbedaan ini dikarenakan faktor elemen director dan ketebalannya.</strong></p><p><strong><br /></strong></p><p><strong><em>Kata Kunci</em></strong> – <em>Atena Televisi, Atena Yagi-Uda, Atena Dipole, Gain, Bandwidth</em></p><p><em> </em></p><p><em>Abstract</em> <strong>- Antenna is a transmitter tool that is familiar with daily activity and easy to find at home, in the building, even on the communication tool used. One of antenna that is often used is a television antenna. Television antennas are often used is Yagi-Uda which is usually used as an outdoor antenna and dipole antenna that is usually used for indoor antennas. Each type of antenna has the criteria and advantages based on the needs of its use. Both dipole antennas and Yagi-Uda antennas have differences among them are bandwidth, gain, and radiation pattern. In this paper it can be seen that the bandwidth of yagi-uda antenna is bigger than dipole antenna that is 0.39943 MHz for Yagi-Uda antenna and 0.16569 MHz for dipole antenna. Neither the large Gain of the Yagi-Uda antenna (6.64 dBi) is greater than the gain of the dipole antenna (2.29 dBi). This difference is due to element factor of director and its thickness.</strong></p><p><strong><br /></strong></p><p><strong><em>Keywords</em></strong><strong> – </strong><em>Television Antenna, Yagi-Uda Antenna, Dipole Antenna, Gain, Bandwidth</em><strong> </strong></p>

Dual Band Slot Antenna for 3.5 WiMAX and 5.8 WLAN

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Sahar Chagharvand ◽  
M. R. B. Hamid ◽  
M. R. Kamarudin ◽  
Mohsen Khalily
Keyword(s):  
Radiation Pattern ◽  
Coplanar Waveguide ◽  
Single Layer ◽  
Dual Band ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Antenna Gain ◽  
Dual Bandwidth ◽  
Electromagnetic Performance ◽  
Good Agreement

This paper presents a single layer planar slot antenna for dual band operation. The antenna is fed by a coplanar waveguide (CPW) with two inverted C-shaped resonators to achieve the dual band operation. The impedance bandwidth for ǀS11ǀ < -10dB is 14% in lower band and 7% in higher band. The antenna prototype’s electromagnetic performance, impedance bandwidth, radiation pattern, and antenna gain were measured. The proposed configuration offers a relatively compact, easy to fabricate and dual band performance providing gain between 2 and 4 dBi. The designed antenna has good dual bandwidth covering 3.5 WiMAX and 5.8 WLAN tasks. Experimental and numerical results also showed good agreement after comparison.

scholarly journals Microstrip patch antenna with metamaterial using superstrate technique for wireless communication

2021 ◽  
Vol 10 (4) ◽  
pp. 2055-2061
Author(s):  
Rasha Mahdi Salih ◽  
Ali Khalid Jassim
Keyword(s):  
Wireless Communications ◽  
Reflection Coefficient ◽  
Wireless Communication ◽  
Patch Antenna ◽  
Relative Permittivity ◽  
Microstrip Antenna ◽  
Microstrip Patch Antenna ◽  
Antenna Gain ◽  
Microstrip Patch ◽  
Antenna Performance

This work builds a metamaterial (MTM) superstrate loaded on a patch of microstrip antenna for wireless communications. The MTM superstrate is made up of four G-shaped resonators on FR-4 substrate with a relative permittivity of 4.4 and has a total area of (8×16) mm2, and is higher than the patch. The MTM superstrate increases antenna gain while also raising the input reflection coefficient. When it is 9 mm above the patch, the gain increased from 3.28 dB to 6.02 dB, and when it is 7 mm above the patch, the input reflection coefficient was enhanced from -31.217 dB to -45.8 dB. When the MTM superstrate loaded antenna was compared to the traditional unloaded antenna, it was discovered that metamaterials have a lot of potential for improving antenna performance.

scholarly journals Multifunctional Partially Reflective Surface for Smart Blocks

Sensors ◽  
2021 ◽  
Vol 21 (19) ◽  
pp. 6508
Author(s):  
Jae Hee Kim ◽  
Dong-Jin Lee ◽  
Tae-Ki An ◽  
Jong-Gyu Hwang ◽  
Chi-Hyung Ahn
Keyword(s):  
High Gain ◽  
Antenna Gain ◽  
High Gain Antenna ◽  
Reflective Surface ◽  
Antenna Performance ◽  
Directional Radiation ◽  
Performance Deterioration ◽  
Polarization Characteristics ◽  
Half Power ◽  
Gain Characteristic

In general, a partially reflective surface (PRS) is mainly used to increase the gain of an antenna; some metallic objects placed on the PRS degrades the antenna performance because the objects change the periodic structure of the PRS. Herein, we propose a multifunctional PRS for smart block application. When a passenger passes over a smart block, the fare can be simultaneously collected and presented through the LED display. This requires high gain antenna with LED structure. The high gain characteristic helps the antenna identify passengers only when they pass over the block. The multifunctional PRS has a structure in which an LED can be placed in the horizontal direction while increasing the antenna gain. We used the antenna’s polarization characteristics to prevent performance deterioration when LED lines are placed in the PRS. We built the proposed antenna and measured its performance: At 2.41 GHz, the efficiency was 81.4%, and the antenna gain was 18.3 dBi. Furthermore, the half-power beamwidth was 18°, confirming a directional radiation pattern.

scholarly journals Mutual Coupling Reduction in Patch Antenna Array Based on EBG Structure for MIMO Applications

2019 ◽  
Vol 63 (4) ◽  
pp. 332-342 ◽  
Author(s):  
Yahiea Alnaiemy ◽  
Taha A. Elwi ◽  
Lajos Nagy
Keyword(s):  
Resonant Frequency ◽  
Antenna Array ◽  
Mutual Coupling ◽  
Multiple Input Multiple Output ◽  
Microstrip Antennas ◽  
Separation Distance ◽  
Rectangular Slot ◽  
Antenna Performance ◽  
Before And After ◽  
Input Multiple Output

This paper presents a printed rectangular slot microstrip antenna array of two elements based on an Electromagnetic Band Gap (EBG) structure. The proposed EBG structure is invented to improve the isolation between the radiating elements for multiple-input multiple-output (MIMO) application. Single and two slotted rectangular microstrip antennas are designed on an FR-4 substrate with a dielectric constant (εr) of 4.3 and loss tangent (tanδ) of 0.025 with thickness of 1.6 mm. The proposed EBG structure is designed as one planar row of 24 slots. The proposed array performance is tested numerically using Computer Simulation Technology Microwave Studio (CSTMW) of Finite Integration Technique (FIT) formulations. The antenna performance in terms of reflection coefficient (S11), isolation coefficient (S21), radiation patterns, boresight gain and Envelope Correlation Coefficient (ECC) are investigated before and after introducing the EBG structure to identify the significant enhancements. The proposed EBG structure is located between the radiating antenna elements to reduce the mutual coupling of the proposed antenna array. The edge to edge separation distance of the proposed antennas is λ0/16, where the λ0 is the free space wavelength at 2.45 GHz. The simulated results show a significant isolation enhancement from –6 dB to –29 dB at the first resonant frequency 2.45 GHz and from –10 dB to –25 dB at the second resonant frequency 5.8 GHz after introducing the EBG structure to the antenna array.

Sign in / Sign up

Export Citation Format

Share Document