scholarly journals Research on variation law of geophysical drill-bit downhole flow field under the interaction of multiple hydraulic factors

2021 ◽  
Vol 104 (3) ◽  
pp. 003685042110316
Author(s):  
Zhiqiang Huang ◽  
Wenlin Zhang ◽  
Jing Zhu ◽  
Dou Xie ◽  
Maolin Dai
Keyword(s):  
Flow Field ◽  
Removal Efficiency ◽  
Hydraulic Structure ◽  
Simulation Software ◽  
Flow Channel ◽  
Petroleum Exploration ◽  
Drill Bit ◽  
Geophysical Prospecting ◽  
Structure Factors ◽  
Chip Removal

Mountain geophysical prospecting operations play an important role in the entire petroleum exploration field. Geophysical drill-bit is the main tool for mountain geophysical prospecting operations. Its hydraulic structure directly affects the downhole flow field and then affects the chip removal efficiency and drilling efficiency of the bit. At present, most of the scholars’ research is focused on Poly Diamond Crystalline bit, roller bit, etc., and the research on geophysical drill-bit is less, and most of them study the downhole flow field based on the change of single hydraulic structure. The primary objective of this research is to study the variation law of the downhole flow field under the interaction of multiple hydraulic structure factors. The drilling time and cuttings size of two geophysical drill-bits with different hydraulic structures are compared, and the key hydraulic structure factors are selected for analysis. Using numerical simulation software, take different levels of key hydraulic structure parameters and carry out orthogonal experiments. Under the interaction of various factors, study the flow field distribution in the flow channel, the downhole, and the annulus area of the shaft lining. The hydraulic structure of the geophysical drill-bit is closely related to the drilling speed and chip removal efficiency. When multiple hydraulic factors are changed, the diameter of the flow channel is the best when it is 10–12.5 mm, the inclination of the flow channel should be set as close as possible to the center of the downhole, and the length of the chip groove increases, the movement of cuttings is more stable. Variation law of downhole flow field under the interaction of multiple hydraulic factors is studied. This study provides a basis for the hydraulic structure design and optimization of the geophysical drill-bit.

scholarly journals Hydraulic structure design and downhole flow field optimization of geophysical drill bits in a limestone stratum

2020 ◽  
Vol 103 (3) ◽  
pp. 003685042093125
Author(s):  
Jing Zhu ◽  
Zhiqiang Huang ◽  
Yachao Ma ◽  
Dou Xie ◽  
Xueying Yang ◽  
...  
Keyword(s):  
Flow Field ◽  
Hydraulic Structure ◽  
Field Tests ◽  
Simulation Method ◽  
Flow Path ◽  
Structure Design ◽  
Drill Bit ◽  
Drilling Performance ◽  
Flow Field Characteristics ◽  
Shaft Lining

The hydraulic structure of conventional geophysical drill bit is designed for the general stratum. When conventional geophysical drill bit pierces into a limestone stratum, the shape of cuttings is large because of the high brittleness of limestone. The cuttings are ground repeatedly; this phenomenon can reduce drilling efficiency and increase drilling costs. According to the characteristics of limestone cuttings, the numerical simulation method is used to research downhole flow field characteristics of conventional geophysical drill bit. First, the influence of key hydraulic structure parameters on cuttings removal performance is found. Then, the hydraulic structure is optimized. The flow field characteristics of the hydraulic structure of the geophysical drill bit before and after optimization in the flow path is analyzed, at the bottom of the bit and the annulus area of the shaft lining. The optimized downhole crossflow area increased from 50% to 98%. No vortex was observed at the exit of the flow path and cuttings groove. The downhole pressure gradient increased from 0.12 Mpa to 0.15 Mpa. The cutting removal space in the annulus area of the shaft lining is fully utilized. Field tests show that the cutting removal and drilling performance of optimized geophysical drill bit has improved and the drilling speed increases by 20.6%.

Flow Field Simulation of the Solo-Supported High Pressure Gas Device of Double-Layer Air Jet Looms

2011 ◽  
Vol 101-102 ◽  
pp. 512-515
Author(s):  
Yi Sheng Liu ◽  
Xu Dong Hu ◽  
Peng Dong Su
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Flow Velocity ◽  
Double Layer ◽  
Research Program ◽  
Flow Channel ◽  
Feasibility Analysis ◽  
Middle Line ◽  
Air Jet ◽  
Field Simulation

A research program is currently underway with the purpose of developing a double-layer air jet looms with solo-supported gas device. Issues related to the design and feasibility analysis of the solo-supported high pressure gas device are discussed. The results of simulations show that assistant nozzle is necessary during weft insertion motion, but too many assistant nozzles would cause the flow velocity reduce. And it is confirmed that flow channel with one main and four assistant nozzles is one of the best designs to keep the flow velocity at the middle line of flow channel more than 90m/s and make the loom work swimmingly.

Aerodynamic Design and Optimization of Pipe Diffuser for a High-Loading Centrifugal Compressor

2017 ◽  
Author(s):  
Xi Yang ◽  
Dong-hai Jin ◽  
Xing-min Gui
Keyword(s):  
Flow Field ◽  
Design Method ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Simulation Software ◽  
Field Analysis ◽  
Superior Performance ◽  
Critical Cross Section ◽  
Isentropic Efficiency ◽  
Vane Diffuser

Pipe diffuser draws more attentions these years as the stage pressure ratio and loads grow, since it is known that the pipe diffuser has a superior performance to the traditional vane diffuser as the diffuser inlet flow field is transonic or supersonic. Generally speaking, when the pressure ratio is high enough to give rise to the emergence of a critical cross-section, it would usually be in the diffuser, closing to the leading edge other than in the impeller. Therefore, the diffuser would have a significant impact on stage choke margin and its performance while be difficult to design and to match the impeller with satisfaction. To address the problem, a preliminary geometry design method for pipe diffuser is presented in this paper. In this paper, the performance and flow field analysis are based on numerical simulation carried out by Numeca, a commercial simulation software. For verified the calculated results′ reliability and grid independence, corresponding calculations and comparisons are conducted and discussed. Then, the performance of stage with pipe diffuser is compared with the stage with vane diffuser. Next, the specific effects of incidence on the performance and flow field are analyzed and discussed respectively. At last, an optimized aerodynamic structure of pipe diffuser is presented. As shown in the CFD results, the stage peak isentropic efficiency can reach up to 83.65% with the stage total pressure ratio slightly increased from 6.50 to 6.78, which means 4.29% of isentropic efficiency was raised by substituting the pipe diffuser for the vane diffuser.

Drilling of bone: Effect of drill bit geometries on thermal osteonecrosis risk regions

2018 ◽  
Vol 233 (2) ◽  
pp. 207-218 ◽  
Author(s):  
Mohd Faizal Ali Akhbar ◽  
Ahmad Razlan Yusoff
Keyword(s):  
Ex Vivo ◽  
Helix Angle ◽  
Simulation Software ◽  
Drilling Process ◽  
Drill Bit ◽  
Temperature Elevation ◽  
Bone Drilling ◽  
Drilling Simulation ◽  
Deform 3D ◽  
Bone Effect

Bone-drilling operation necessitates an accurate and efficient surgical drill bit to minimize thermal damage to the bone. This article provides a methodology for predicting the bone temperature elevation during surgical bone drilling and to gain a better understanding on the influences of the point angle, helix angle and web thickness of the drill bit. The proposed approach utilized the normalized Cockroft–Latham damage criterion to predict material cracking in the drilling process. Drilling simulation software DEFORM-3D is used to approximate the bone temperature elevation corresponding to different drill bit geometries. To validate the simulation results, bone temperature elevations were evaluated by comparison with ex vivo bone-drilling process using bovine femurs. The computational results fit well with the ex vivo experiments with respect to different drill geometries. All the investigated drill bit geometries significantly affect bone temperature rise. It is discovered that the thermal osteonecrosis risk regions could be reduced with a point angle of 110° to 140°, a helix angle of 5° to 30° and a web thickness of 5% to 40%. The drilling simulation could accurately estimate the maximum bone temperature elevation for various surgical drill bit point angles, web thickness and helix angles. Looking into the future, this work will lead to the research and redesign of the optimum surgical drill bit to minimize thermal insult during bone-drilling surgeries.

Chip Removal by a Hydraulic Jet

1964 ◽  
Vol 4 (01) ◽  
pp. 21-25 ◽  
Author(s):  
J.B. Cheatham ◽  
J.G. Yarbrough
Keyword(s):  
Flow Rate ◽  
Particle Density ◽  
Experimental Studies ◽  
Fluid Viscosity ◽  
Drill Bit ◽  
Hole Size ◽  
Rock Fracturing ◽  
Fracturing Process ◽  
Jet Velocity ◽  
Chip Removal

Abstract Although adequate removal of cuttings from beneath a drill bit is important for efficient drilling operations, very little basic data are available relative to the fundamentals of chip removal by hydraulic jets. A discussion is presented in this paper of an experimental investigation of the jetting action of hydraulic jets in removing loose particles from the bottom of a cylindrical hole. Conditions for which the jet is no longer capable of removing chips from the bottom of the hole are determined. This situation represents equilibrium between the chip removal force and chip holddown forces such as gravity and pressure. In most of the tests loose particles were jetted with water or a water-glycerine mixture to determine the dependence of chip removal on hole size, jet size, height of jet off bottom of hole, flow rate, particle density and fluid viscosity. A test with a pressurized mud system indicated that relatively low pressures can completely overcome the removal action of a hydraulic jet. Although the system studied herein is not directly applicable to a rotary drill bit, the work with such simplified systems can provide a better understanding of the chip removal action of jets, and with logical extensions it may provide a reasonable basis for the best use of fluid jets in drilling. Introduction The primary deterrent to maximum drilling rates is the inability of the drilling system to remove rock cuttings efficiently enough to prevent interference with the drilling action. The objective of chip removal studies is to permit predicting and controlling removal forces under downhole drilling conditions. Conditions at the bottom of a hole during rotary drilling are exceedingly complex and are not likely to be described in a quantitative way by investigations in terms of the total drilling action until a better understanding is developed of the simplified components of the problem. The present study is concerned with the elementary condition of removal of chips by a single central jet. Even this relatively simple model provides mathematical difficulties because of the turbulent nature of the flow from the jet and because of the shape of the bottom of the hole beneath the jet. Theoretical and experimental studies have been made of turbulent jets impinging normally on an infinite body and deductions based on analytical solutions to simplified problems can give some insight into the problem of cutting removal by a jet. However, because of the present lack of understanding of the behavior of the interaction between the fluid jet and the chips being removed, an experimental approach was chosen for the present study. Methods have been developed for maximizing hydraulic horsepower, impact force and jet velocity; but whether maximizing these parameters maximizes chip removal with present drilling bits has not been demonstrated. Simplifying the problem of chip removal may make it possible to develop some understanding of the manner in which the jet velocity is dissipated. Better understanding of a simple case should materially assist in extending analysis to more complicated cases. Thus, we are not concerned in the present study with the rock fracturing process itself but only with the removal of the debris from the bottom of the hole. A problem which is quite similar to the chip removal problem is the suspension of solids in stirred vessels. This problem has been studied by the chemical industry and correlations have been obtained by dimensional analysis which permit the design of mixing vats. An approach similar to that used in the mixing vat problem is used in the analysis of the jetting data in the present paper. EXPERIMENTAL PROCEDURE The test equipment arrangement shown schematically in Fig. 1 allows the jetting action to remove particles until an equilibrium height is attained for each combination of hole size, jet size and flow rate.*** Equilibrium conditions require that the removal force is unable to remove additional particles. This balance between holddown and removal forces implies a relationship between the two forces which is constant for the particular system. When the holddown forces are constant, SPEJ P. 21ˆ

Development and verification of a general approach to describe the efficiency of vortex separators in combined sewer systems

2007 ◽  
Vol 55 (4) ◽  
pp. 165-173
Author(s):  
T. Mietzel ◽  
K. Klepiszewski ◽  
G. Weiss
Keyword(s):  
Removal Efficiency ◽  
Large Scale ◽  
Cost Effective ◽  
Large Error ◽  
Simulation Software ◽  
Pollutant Removal ◽  
Attractive Alternative ◽  
Dynamic Approach ◽  
General Applicability ◽  
Pollutant Removal Efficiency

The water framework directive (CEC, 2000) asks for cost-effective measures for achieving good ecological conditions in receiving waters. Because of low operation costs and good pollutant removal efficiency, vortex separators (VS) are an attractive alternative to traditional stormwater tanks. The German design standard for CSO structures, ATV-A 128 (1992), demands long-term pollution load simulations. Today's simulation software, however, considers the removal processes in CSO structures either very rudimentarily or not at all. The higher pollutant removal efficiency of a structure like a VS cannot be taken into account. This might be one reason why VS are used still comparatively scarcely. A mathematical model describing the removal efficiency could increase the acceptance of VS. Several functions describing the removal efficiency have been derived from model tests or large-scale studies within the last few years. Within this paper, the data from three large-scale studies are used to verify the general applicability of one steady-state and one dynamic approach. The results show that the complex processes involved with CSO facilities and the large error related to monitoring make the validation of models a difficult task. Anyhow, especially the dynamic approach was applicable at all considered facilities.

Structure Reverse Design and CFD Analysis on Agitated Flow Field of Submersible Mixer

2011 ◽  
Vol 383-390 ◽  
pp. 25-31
Author(s):  
Wei Xing Xu ◽  
Ming Yue Fan
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Simulation Software ◽  
The Body ◽  
Engineering Theory ◽  
Measuring Machine ◽  
3D Solid

The impeller of submersible mixer in some sewage treatment plant, whose parts are imported from other countries, is heavily abased. To solve this problem and realize domestic manufacture, based on reverse engineering theory, utilizing 3 coordinates measuring machine and applications of Surface and Pro/E, 3D solid model of impeller are gained. The gained impeller model accords with the physical one with high accuracy. The flow formulation is founded as console formulation first, and with the body-fitted coordinate system and standard turbulent model, the numerical simulation of the internal 3-D incompressible turbulent flow agitated flow field of submersible mixer is carried out by numerical simulation software Fluent. The results showed that: the mixer impeller produced vortex jet flow, the constant velocity lines advanced as ellipse, the velocity along the centerline are larger than others, and utilized volume flow to transport the liquid.

Numerical Simulation Applied to Study the Effects of Fractal Tree-Liked Network Channel Designs on PEMFC Performance

2012 ◽  
Vol 488-489 ◽  
pp. 1219-1223 ◽  
Author(s):  
Shan Jen Cheng ◽  
Jr Ming Miao ◽  
Chang Hsien Tai
Keyword(s):  
Fuel Cell ◽  
Pressure Drop ◽  
Flow Field ◽  
Fluid Dynamic ◽  
Flow Distribution ◽  
Flow Channel ◽  
Proton Exchange ◽  
Channel Network ◽  
Computational Fluid Dynamic Analysis ◽  
Network Channel

The effect of pressure drop and the flow-field of inhomogeneous transport of reactions gas are two important issues for bipolar flow channel design in proton exchange membrane fuel cell (PEMFC). A novel design through the imitation of biological development of the topology distribution of fractal tree-liked network channel is the main topic of this research. The effects of different Reynolds numbers and stoichiometric mass flow rate of reaction gas on the flow field distribution of tree-like channels were investigated by three-dimensional computational fluid dynamic analysis. According to numerical simulations, the fractal tree-liked network channel would have an excellent performance on the uniformity of multi-branching flow distribution and lower pressure drop along channels. The new type of fractal tree-liked bionic flow channel network design will be applied to assist in the experimental reference for improving the performance of fuel cell stack system in PEMFC for future.

EGR System Performance Optimization of Diesel Engine Based on GT-Power and Fluent Co-Simulation

2013 ◽  
Vol 860-863 ◽  
pp. 1703-1709 ◽  
Author(s):  
Xian Jun Hou ◽  
Shu Chen ◽  
Zhi'en Liu
Keyword(s):  
Diesel Engine ◽  
Flow Field ◽  
Performance Optimization ◽  
Engine Performance ◽  
Simulation Software ◽  
Field Analysis ◽  
Three Dimension ◽  
Air Inlet ◽  
Inlet Position ◽  
The Impact

A calculation model of turbocharged diesel engine was developed based on one-dimension simulation software GT-power,which can provide a steady boundary condition for the flow field analysis of EGR system.The three-dimension simulation software Fluent was applied in establishing the flow field model of the air-intake system under different air inlet position to analize the distribution of the exhaust gas,and then obtained the impact of the EGRs air-inlet position to uniformity of EGR system, thereby we could acquire the parameters which achieves the best maching between the EGR system and the diesel engine, it also provided a reference for engine performance optimization.

scholarly journals An Ultrasound Simulation Model for the Pulsatile Blood Flow Modulated by the Motion of Stenosed Vessel Wall

2016 ◽  
Vol 2016 ◽  
pp. 1-16
Author(s):  
Qinghui Zhang ◽  
Yufeng Zhang ◽  
Yi Zhou ◽  
Kun Zhang ◽  
Kexin Zhang ◽  
...  
Keyword(s):  
Blood Flow ◽  
Flow Field ◽  
Simulation Model ◽  
Vessel Wall ◽  
Wall Motion ◽  
Simulation Software ◽  
Pulsatile Blood Flow ◽  
Ultrasound Simulation ◽  
Wall Movement ◽  
Stenosed Vessel

This paper presents an ultrasound simulation model for pulsatile blood flow, modulated by the motion of a stenosed vessel wall. It aims at generating more realistic ultrasonic signals to provide an environment for evaluating ultrasound signal processing and imaging and a framework for investigating the behaviors of blood flow field modulated by wall motion. This model takes into account fluid-structure interaction, blood pulsatility, stenosis of the vessel, and arterial wall movement caused by surrounding tissue’s motion. The axial and radial velocity distributions of blood and the displacement of vessel wall are calculated by solving coupled Navier-Stokes and wall equations. With these obtained values, we made several different phantoms by treating blood and the vessel wall as a group of point scatterers. Then, ultrasound echoed signals from oscillating wall and blood in the axisymmetric stenotic-carotid arteries were computed by ultrasound simulation software, Field II. The results show better consistency with corresponding theoretical values and clinical data and reflect the influence of wall movement on the flow field. It can serve as an effective tool not only for investigating the behavior of blood flow field modulated by wall motion but also for quantitative or qualitative evaluation of new ultrasound imaging technology and estimation method of blood velocity.

Sign in / Sign up

Export Citation Format

Share Document