Influence of vaned diffuser on the potential effect of volute and stall inception of centrifugal compressor

2020 ◽  
Vol 234 (10-11) ◽  
pp. 2546-2560 ◽  
Author(s):  
Li Fu ◽  
Ce Yang ◽  
Hang Zhang ◽  
Wenrui Bao ◽  
Hanzhi Zhang
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Static Pressure ◽  
Potential Effect ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Stable Operating ◽  
Circumferential Distribution ◽  
Stagger Angle ◽  
Circumferential Nonuniformity

In the automotive turbochargers centrifugal compressor, the volute has a strong potential effect, leading to circumferential nonuniformity of the impeller flow field and compressor stall. In this study, full-annulus unsteady simulations for centrifugal compressors with vaned/vaneless diffusers are carried out. The influence of the diffuser vane on the potential effect of the volute and stall behavior of a centrifugal compressor is studied in detail. Based on the distribution of the casing static pressure, the formation mechanism of the circumferential distribution of static pressure and the reverse propagation process of pressure waves caused by pressure distortion are revealed. The results of this study show that the diffuser vanes can weaken the potential effect of the volute on the impeller flow field by reducing the degree of static pressure distortion. The number of static pressure peaks in the circumferential direction is related to the number of vanes/blades. The diffuser vanes can change the circumferential position of the stall inception, but cannot eliminate the “locking effect” of the volute tongue on the circumferential position of the stall. In other words, the circumferential position of the stall inception is still determined by the volute tongue for a centrifugal compressor with a vaned diffuser. Although the degree of circumferential static pressure distortion inside the impeller is reduced, the stable operating range of the compressor cannot be significantly widened by adjusting the stagger angle of the diffuser vane when the stall first occurs at the impeller inlet.

An Investigation of the Stability Enhancement of a Centrifugal Compressor Stage Using a Porous Throat Diffuser

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Lee Galloway ◽  
Stephen Spence ◽  
Sung In Kim ◽  
Daniel Rusch ◽  
Klemens Vogel ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Stall Inception ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Stable Operating ◽  
The Stability ◽  
Circumferential Pressure

The stable operating range of a centrifugal compressor stage of an engine turbocharger is limited at low mass flow rates by aerodynamic instabilities which can lead to the onset of rotating stall or surge. There have been many techniques employed to increase the stable operating range of centrifugal compressor stages. The literature demonstrates that there are various possibilities for adding special treatments to the nominal diffuser vane geometry, or including injection or bleed flows to modify the diffuser flow field in order to influence diffuser stability. One such treatment is the porous throat diffuser (PTD). Although the benefits of this technique have been proven in the existing literature, a comprehensive understanding of how this technique operates is not yet available. This paper uses experimental measurements from a high pressure ratio (PR) compressor stage to acquire a sound understanding of the flow features within the vaned diffuser which affect the stability of the overall compression system and investigate the stabilizing mechanism of the porous throat diffuser. The nonuniform circumferential pressure imposed by the asymmetric volute is experimentally and numerically examined to understand if this provides a preferential location for stall inception in the diffuser. The following hypothesis is confirmed: linking of the diffuser throats via the side cavity equalizes the diffuser throat pressure, thus creating a more homogeneous circumferential pressure distribution, which delays stall inception to lower flow rates. The results of the porous throat diffuser configuration are compared to a standard vaned diffuser compressor stage in terms of overall compressor performance parameters, circumferential pressure nonuniformity at various locations through the compressor stage and diffuser subcomponent analysis. The diffuser inlet region was found to be the element most influenced by the porous throat diffuser, and the stability limit is mainly governed by this element.

Investigation of Stall Process in a Centrifugal Compressor With a Volute Under Transonic Conditions

2019 ◽  
Author(s):  
Ce Yang ◽  
Wenli Wang ◽  
Hanzhi Zhang ◽  
Yanzhao Li ◽  
Ding Tong ◽  
...  
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Static Pressure ◽  
Cell Formation ◽  
Internal Flow ◽  
Growth Zone ◽  
Asymmetric Structure ◽  
Stall Inception ◽  
Stall Cells ◽  
Inlet Conditions

Abstract In a centrifugal compressor with a volute, the internal flow field is circumferentially nonuniform owing to the asymmetric structure of the volute. Currently, the mechanisms by which the volute influences the stall inception circumferential position and the stall process in a transonic centrifugal compressor are not clear. In this study, the stall process in the centrifugal compressor with a volute is investigated under transonic inlet conditions. Obtained by experimental and simulation results, the static pressure distributions around the casing wall are compared with each other. Thereafter, an unsteady simulation is conducted on the stall process under transonic inlet conditions. By analyzing the stall cell evolution pattern at the impeller inlet, the stall process can be divided into three stages: stall onset, stall development, and stall maturation. The spike-type stall inceptions occur twice at the tip in the circumferential 135° position of the impeller inlet. This circumferential position is also the affected position of the high static pressure region induced by the volute tongue. Because of the circumferentially nonuniform flow field, there is a stall cell decay zone and a stall cell formation/growth zone at the impeller inlet. For the compressor under study, the approximate circumferential range of 135° to 270° is the decay zone, and the circumferential range of 270° to 360° is the formation/growth zone. The stall inception cannot occur in the decay zone. However, the stall cells can pass through the decay zone when the stall cell size is large enough. The first stall inception cannot propagate circumferentially, while the second one can. The propagation speed of stall cells in the circumferential direction is at approximately 70% of the rotational speed of impeller.

Stability Improvement of a Turbocharger Centrifugal Compressor by a Nonaxisymmetric Vaned Diffuser

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Xinqian Zheng ◽  
Zhenzhong Sun ◽  
Tomoki Kawakubo ◽  
Hideaki Tamaki
Keyword(s):  
Flow Field ◽  
Flow Control ◽  
Centrifugal Compressor ◽  
Flow Separation ◽  
Static Pressure ◽  
Control Method ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Vaned Diffuser ◽  
Positive Effects

The nonuniformity of the flow field induced by a nonaxisymmetric volute significantly degrades the stability of a turbocharger centrifugal compressor. In this paper, a nonaxisymmetric vaned diffuser is investigated as a nonaxisymmetric flow control method using both three-dimensional computational fluid dynamics (CFD) and experiment. The numerical study first focuses on the relationship between the flow field and the static pressure distortion, and the steady CFD results indicate that the positive static pressure gradient in the rotating direction facilitates flow separation in the vaned diffuser and induces a nonuniform flow field. A nonaxisymmetric flow control method with variable stagger and solidity of the vaned diffuser is developed to suppress the flow separation, and the guideline of the method suggests narrowing flow passages where the flow separates or closing diffuser vanes upstream of flow separations. Steady CFD also presents the flow field of the investigated turbocharger centrifugal compressor with volute, and flow separation is found in the flow passages near the volute tongue. Under the guidance of the nonaxisymmetric flow control method, several nonaxisymmetric vaned diffusers are designed to make the flow field uniform, which are believed to be beneficial for compressor stability. Finally, an experiment is carried out to validate the positive effects of the nonaxisymmetric vaned diffuser for stability improvement. The test data show that Non-AxisVD (with a nonaxisymmetric vaned diffuser) extends the stable flow range (SFR) of the compressor by 26% compared with the AxisVD (with an axisymmetric vaned diffuser), at the cost of acceptable decreases in the maximum total pressure ratio and peak efficiency.

An Investigation of the Stability Enhancement of a Centrifugal Compressor Stage Using a Porous Throat Diffuser

2017 ◽  
Author(s):  
Lee Galloway ◽  
Stephen Spence ◽  
Sung In Kim ◽  
Daniel Rusch ◽  
Klemens Vogel ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Stall Inception ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Stable Operating ◽  
The Stability ◽  
Circumferential Pressure

The stable operating range of a centrifugal compressor stage of an engine turbocharger is limited at low mass flow rates by aerodynamic instabilities which can lead to the onset of rotating stall or surge. There have been many techniques employed to increase the stable operating range of centrifugal compressor stages. The literature demonstrates that there are various possibilities for adding special treatments to the nominal diffuser vane geometry, or including injection or bleed flows to modify the diffuser flow field in order to influence diffuser stability. One such treatment is the porous throat diffuser. Although the benefits of this technique have been proven in the existing literature, a comprehensive understanding of how this technique operates is not yet available. This paper uses experimental measurements from a high pressure ratio compressor stage to acquire a sound understanding of the flow features within the vaned diffuser which affect the stability of the overall compression system and investigate the stabilising mechanism of the porous throat diffuser. The non-uniform circumferential pressure imposed by the asymmetric volute is experimentally and numerically examined to understand if this provides a preferential location for stall inception in the diffuser. The following hypothesis is confirmed: linking of the diffuser throats via the side cavity equalizes the diffuser throat pressure, thus creating a more homogeneous circumferential pressure distribution, which delays stall inception to lower flow rates. The results of the porous throat diffuser configuration are compared to a standard vaned diffuser compressor stage in terms of overall compressor performance parameters, circumferential pressure non-uniformity at various locations through the compressor stage and diffuser sub-component analysis. The diffuser inlet region was found to be the element most influenced by the porous throat diffuser and the stability limit is mainly governed by this element.

Non-Uniform Two-Phase Flow of Supercritical Carbon Dioxide Centrifugal Compressor

2020 ◽  
Author(s):  
Wenrui Bao ◽  
Ce Yang ◽  
Li Fu ◽  
Changmao Yang ◽  
Lucheng Ji
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Static Pressure ◽  
Leading Edge ◽  
Phase Region ◽  
Tip Clearance ◽  
Two Phase ◽  
Supercritical Carbon

Abstract An asymmetric structure of volute in a supercritical carbon dioxide centrifugal compressor induces a non-uniform circumferential distribution of the upstream flow field, which inevitably affects the formation of a two-phase region of carbon dioxide in an impeller. In this work, unsteady simulations for centrifugal compressors were conducted. First, the influence of low static strip induced by low static pressure near volute tongue on the impeller flow field was presented. Then, the non-uniform flow field distribution in the impeller passages and flow characteristics of the passages at the impeller inlet were obtained. Finally, the two-phase regions in the impeller were presented. The results demonstrate that for a centrifugal compressor with volute, the two-phase region appears not only on the suction surface of the leading edge of the blade, but also in some impeller passages, on the pressure surface of the blade near the leading edge, and in the leading edge and mid-chord of tip clearance, under the design conditions. The low static pressure strip induced by the volute leads to a high-speed region in the impeller passages where the temperature and pressure of supercritical carbon dioxide fall below the critical point and carbon dioxide enters the two-phase region. Meanwhile, the static pressure on the blade surface is distorted under the influence of a high-speed region in the passages, resulting in the formation of a two-phase region at the tip clearance. The flow distortion of passages at the impeller inlet results in the appearance of two-phase regions on the both sides of leading edge of the blade. The dryness on the suction side of the blade leading edge and the leading edge of the tip clearance is lower, which indicated that the proportion of liquid-phase carbon dioxide is higher in these two-phase regions.

Improving a Vaned Diffuser for a Given Centrifugal Impeller by 3D Inverse Design

2002 ◽  
Author(s):  
Mehrdad Zangeneh ◽  
Damian Vogt ◽  
Christian Roduner
Keyword(s):  
Flow Field ◽  
Viscous Flow ◽  
Centrifugal Compressor ◽  
Inverse Method ◽  
Flow Distribution ◽  
Inverse Design ◽  
Centrifugal Impeller ◽  
Design Code ◽  
Vaned Diffuser ◽  
Blade Loading

In this paper the application of 3D inverse design code TURBOdesign−1 to the design of the vane geometry of a centrifugal compressor vaned diffuser is presented. For this study the new diffuser is designed to match the flow leaving the conventional impeller, which is highly non-uniform. The inverse method designs the blade geometry for a given specification of thickness and blade loading distribution. The paper describes the choice of loading distribution used in the design as well as the influence of the diffuser inlet flow distribution on the vane geometry and flow field. The flow field in the new diffuser is analysed by a 3D viscous flow code and the result is compared to that of the conventional diffuser. Finally the results of testing the stage performance of the new diffuser is compared with that of the conventional stage.

scholarly journals An Investigation of Surge in a High-Speed Centrifugal Compressor Using Digital PIV

2000 ◽  
Vol 123 (2) ◽  
pp. 418-428 ◽  
Author(s):  
Mark P. Wernet ◽  
Michelle M. Bright ◽  
Gary J. Skoch
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
High Speed ◽  
Transient Flow ◽  
Dynamic Pressure ◽  
Rotating Stall ◽  
Transient Pressure ◽  
Pressure Transducers ◽  
Stable Operating ◽  
Particle Imaging

Compressor stall is a catastrophic breakdown of the flow in a compressor, which can lead to a loss of engine power, large pressure transients in the inlet/nacelle, and engine flameout. The implementation of active or passive strategies for controlling rotating stall and surge can significantly extend the stable operating range of a compressor without substantially sacrificing performance. It is crucial to identify the dynamic changes occurring in the flow field prior to rotating stall and surge in order to control these events successfully. Generally, pressure transducer measurements are made to capture the transient response of a compressor prior to rotating stall. In this investigation, Digital Particle Imaging Velocimetry (DPIV) is used in conjunction with dynamic pressure transducers to capture transient velocity and pressure measurements simultaneously in the nonstationary flow field during compressor surge. DPIV is an instantaneous, planar measurement technique that is ideally suited for studying transient flow phenomena in high-speed turbomachinery and has been used previously to map the stable operating point flow field in the diffuser of a high-speed centrifugal compressor. Through the acquisition of both DPIV images and transient pressure data, the time evolution of the unsteady flow during surge is revealed.

Some Studies on Low Solidity Vaned Diffusers of a Centrifugal Compressor Stage

2005 ◽  
Author(s):  
T. Ch. Siva Reddy ◽  
G. V. Ramana Murty ◽  
Prasad Mukkavilli ◽  
D. N. Reddy
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Pressure Recovery ◽  
Compressor Stage ◽  
Recovery Coefficient ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Centrifugal Compressor Stage ◽  
Pressure Recovery Coefficient

Numerical simulation of impeller and low solidity vaned diffuser (LSD) of a centrifugal compressor stage is performed individually using CFX- BladeGen and BladeGenPlus codes. The tip mach number for the chosen study was 0.35. The same configuration was used for experimental investigation for a comparative study. The LSD vane is formed using standard NACA profile with marginal modification at trailing edge. The performance parameters obtained form numerical studies at the exit of impeller and the diffuser have been compared with the corresponding experimental data. These parameters are pressure ratio, polytropic efficiency and flow angle at the impeller exit where as the parameters those have been compared at the exit of diffuser are the static pressure recovery coefficient and the exit flow angle. In addition, the numerical prediction of the blade loading in terms of blade surface pressure distribution on LSD vane has been compared with the corresponding experimental results. Static pressure recovery coefficient and flow angle at diffuser exit is seen to match closely at higher flows. The difference at lower flows could be due to the effect of interaction between impeller and diffuser combinations, as the numerical analysis was done separately for impeller and diffuser and the effect of impeller diffuser interaction was not considered.

Steady and Transient Computations of Interaction Effects in a Centrifugal Compressor With Different Types of Diffusers

2010 ◽  
Author(s):  
S. Anish ◽  
N. Sitaram
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Leading Edge ◽  
Design Flow ◽  
Flow Coefficient ◽  
Pressure Recovery ◽  
Maximum Efficiency ◽  
Vaned Diffuser ◽  
Lower Flow ◽  
Transient Simulations

A computational study has been conducted to analyze the performance of a centrifugal compressor under various levels of impeller-diffuser interactions. The study has been conducted using a low solidity vaned diffuser (LSVD), a conventional vaned diffuser (VD) and a vaneless diffuser (VLD). The study is carried out using Reynolds-Averaged Navier-Stokes simulations. A commercial software ANSYS CFX is used for this purpose. The intensity of interaction is varied by keeping the diffuser vane leading edge at three different radial locations. Frozen rotor and transient simulations are carried out at four different flow coefficients. At design flow coefficient maximum efficiency occurs when the leading edge is at R3 (ratio of radius of the diffuser leading edge to the impeller tip radius) = 1.10. At lower flow coefficient higher stage efficiency occurs when the diffuser vanes are kept at R3 = 1.15 and at higher flow coefficient R3 = 1.05 gives better efficiency. It is observed that at lower flow coefficients positive incidence causes separation of flow at the suction side of the diffuser vane. When the flow rate is above design point there is a negative incidence at the leading edge of the diffuser vane which causes separation of flow from the pressure side of the diffuser vane. Compressor stage performance as well as performance of individual components is calculated at different time steps. Large variations in the stage performances at off-design flow coefficients are observed. The static pressure recovery coefficient (Cp) value is found to be varying with the relative position of impeller and diffuser. It is observed that maximum Cp value occurred at time step where Ψloss value is lowest. From the transient simulations it has been found that the strength and location of impeller exit wake affect the diffuser vane loading which in turn influences the diffuser static pressure recovery.

scholarly journals Numerical Simulation of Stall Inception Mechanisms in a Centrifugal Compressor With Vaned Diffuser

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Y. Bousquet ◽  
N. Binder ◽  
G. Dufour ◽  
X. Carbonneau ◽  
M. Roumeas ◽  
...  
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Flow Topology ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Flow Reduction

The present paper numerically investigates the stall inception mechanisms in a centrifugal compressor stage composed of a splittered unshrouded impeller and a vaned diffuser. Unsteady numerical simulations have been conducted on a calculation domain comprising all the blade passages over 360 deg for the impeller and the diffuser. Three stable operating points are simulated along a speed line, and the full path to instability is investigated. The paper focusses first on the effects of the mass flow reduction on the flow topology at the inlet of both components. Then, a detailed analysis of stall inception mechanisms is proposed. It is shown that at the inlet of both components, the mass flow reduction induces boundary layer separation on the blade suction side, which results in a vortex tube having its upper end at the casing and its lower end at the blade wall. Some similarities with flows in axial compressor operating at stall condition are outlined. The stall inception process starts with the growth of the amplitude of a modal wave rotating in the vaneless space. As the flow in the compressor is subsonic, the wave propagates upstream and interacts with the impeller flow structure. This interaction leads to the drop in the impeller pressure ratio.

Sign in / Sign up

Export Citation Format

Share Document