scholarly journals Study on antibacterial and copper ion removal of chitosan fiber/acetate fiber and yarn for water purification

2021 ◽  
Vol 16 ◽  
pp. 155892502110613
Author(s):  
Yating Zhang ◽  
Shujie Zhang ◽  
Lisong Fu ◽  
Mengke Jing

Use chitosan (CS) fiber and cellulose acetate (CA) fiber with different mixing ratios as raw materials, the kinetic and thermodynamic characteristics of the adsorption process of chitosan fiber/cellulose acetate fiber (CS/CA) ratio of 90:10 are explored, and the adsorption process conforms to the quasi-second-order kinetic equation. It can be fitted by Langmuir isotherm. The adsorption process is a spontaneous thermal reaction with both physical adsorption and chemical adsorption. The best adsorption time is 30 min, the time to reach adsorption equilibrium is 180 min, and the best adsorption pH is 5, the most suitable temperature is 35°C, and rising the temperature is conducive to the fibers adsorption. The materials before and after the CS/CA blended yarn adsorbed copper ions were characterized by XRD, DSC, FT-IR, and the adsorption mechanism was analyzed. In the orthogonal experiment, the copper ions concentration has the most obvious effect on the adsorption capacity, and the temperature has the most obvious effect on the adsorption efficiency. The optimal adsorption combination is that the mixing ratio of chitosan fiber/cellulose acetate (CS/CA) is 80:20, the pH is 5, the temperature is 35°C, and the copper ion concentration is 100 mg L−1. Comparing the adsorption performance of fibers with different mixing ratios, the adsorption performance of CS/CA ratio of 90:10 is the best. The filtration efficiency of the filter material, made of fibers with different mixing ratios, to copper ions is tested, and the filtration performance with a mixing ratio of 90:10 is the best, and the filtration efficiency is 64.33%.

2015 ◽  
Vol 804 ◽  
pp. 239-242
Author(s):  
Duongruitai Nicomrat ◽  
Jirasak Tharajak

Copper ions are commonly contaminated in the effluents from many electronic factory. In copper filtration, most filter types are usually expensive and causes toxic residues and creates another health and environmental problem. Therefore, this research has been developed a copper filtration approach based on homemade non-hazardous residues of banana peels, unmeshed sand, and charcoal. The results showed that baked, minced banana peels media could absorb synthetic water having copper ion at 50 ppm with filtration efficiency of 70% within 2 hr. Baked minced banana peels in combination with sand and charcoal could adsorb Copper (II) at 50 mg/ mL more than 80%. However, the swollen structure of banana peels during copper (II) filtration caused limit filtration efficiency to 4-5 hour extraction period. The tentative wastewater treatment application is, therefore, the use of bio-adsorbent for effective adsorption of toxic heavy metals from effluents open discarded from agricultural wastes in the environment.


2021 ◽  
Vol 2080 (1) ◽  
pp. 012032
Author(s):  
Hazreen Nadihah Husni ◽  
Norsuria Mahmed ◽  
Yanling Ge ◽  
Mohd Natashah Norizan ◽  
Dewi Suriyani Che Halin ◽  
...  

Abstract The magnetite (Fe3O4) and maghemite (γFe2O3) nanopartides, magnetite-silica-silver chloride (Fe3O4-SiO2-AgCl) and maghemite-silica-silver chloride (γFe2O3-SiO2-AgCl) coreshell structures have successfully been synthesized by using a simple wet chemistry method. The efficiency of these particles as the adsorbents for the removal of copper ion, Cu2+ in aqueous solution under UV light was investigated. Two different parameters were studied, namely the adsorbents contact time (60, 120, 180, 240 and 300s) and the solution-stirring rate (100, 200 and 300 rpm). From the results, the removal percentage of the copper ions from the solution were above 90% after 5 hours of adsorption process at 300 rpm by using Fe3O4 (94%) and γFe2O3 (92%) nanoparticles. The maximum removal of copper ions was nearly 100% when yFe2O3-SiO2-AgCl & Fe3O4-SiO2-AgCl coreshell particles were used. The samples that were prepared without magnetic core such as AgCl-SiO2, AgCl and SiO2 particles, showed lower percentage of the copper ions removal (78%, 60% and 20%, respectively). This situation shows that the magnetic nanoparticles plays and important role during the adsorption process due to their large active sites for the adsorption to occur.


2019 ◽  
Vol 9 (4) ◽  
pp. 317-325 ◽  
Author(s):  
Misagh Ghamari ◽  
Amin Imani ◽  
James F. Williams ◽  
Mahdi Ghasemifard

Abstract A novel polymethyl methacrylate/boehmite nanocomposite with remarkably enhanced adsorption performance of Cu(II) was synthesized from $${\text{Al}}({\text{NO}}_{3} )_{3} \cdot 9{\text{H}}_{2} {\text{O}}$$Al(NO3)3·9H2O using a facile sol–gel method. The effects of boehmite content, contact time and morphology of hybrid (pH of synthesis) as the main parameters on removal efficiency and removal capability of hybrid on copper ions have been explored. Composites contained between 0.7 and 5wt% boehmite content and those with dissimilar morphology prepared with different pH values showed different adsorption behavior. Batch adsorption experiments show that the adsorption performance of the hybrids was enhanced with increased boehmite and contact time. The highest removal efficiency and adsorption capability were achieved when the hybrid was prepared at pH 8 with associated increased catalytic activity. Graphic abstract


2021 ◽  
Vol 13 (10) ◽  
pp. 1877
Author(s):  
Ukkyo Jeong ◽  
Hyunkee Hong

Since April 2018, the TROPOspheric Monitoring Instrument (TROPOMI) has provided data on tropospheric NO2 column concentrations (CTROPOMI) with unprecedented spatial resolution. This study aims to assess the capability of TROPOMI to acquire high spatial resolution data regarding surface NO2 mixing ratios. In general, the instrument effectively detected major and moderate sources of NO2 over South Korea with a clear weekday–weekend distinction. We compared the CTROPOMI with surface NO2 mixing ratio measurements from an extensive ground-based network over South Korea operated by the Korean Ministry of Environment (SKME; more than 570 sites), for 2019. Spatiotemporally collocated CTROPOMI and SKME showed a moderate correlation (correlation coefficient, r = 0.67), whereas their annual mean values at each site showed a higher correlation (r = 0.84). The CTROPOMI and SKME were well correlated around the Seoul metropolitan area, where significant amounts of NO2 prevailed throughout the year, whereas they showed lower correlation at rural sites. We converted the tropospheric NO2 from TROPOMI to the surface mixing ratio (STROPOMI) using the EAC4 (ECMWF Atmospheric Composition Reanalysis 4) profile shape, for quantitative comparison with the SKME. The estimated STROPOMI generally underestimated the in-situ value obtained, SKME (slope = 0.64), as reported in previous studies.


Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1099
Author(s):  
Sheng-Chun Hung ◽  
Chih-Cheng Lu ◽  
Yu-Ting Wu

The optical characteristics of copper ion detection, such as the photometric absorbance of specific wavelengths, exhibit significant intensity change upon incident light into the aqueous solutions with different concentrations of metal ions due to the electron transition in the orbit. In this study, we developed a low-cost, small-size and fast-response photoelectric sensing prototype as an optic sensor for copper (Cu) ions detection by utilizing the principle of optical absorption. We quantified the change of optical absorbance from infra-red (IR) light emitting diodes (LEDs) upon different concentrations of copper ions and the transmitted optical signals were transferred to the corresponding output voltage through a phototransistor and circuit integrated in the photoelectric sensing system. The optic sensor for copper (Cu) ions demonstrated not only excellent specificity with other metal ions such as cadmium (Cd), nickel (Ni), iron (Fe) and chloride (Cl) ions in the same aqueous solution but also satisfactory linearity and reproducibility. The sensitivity of the preliminary sensing system for copper ions was 29 mV/ppm from 0 to 1000 ppm. In addition, significant ion-selective characteristics and anti-interference capability were also observed in the experiments by the proposed approach.


2019 ◽  
Vol 32 (1) ◽  
pp. 73-78
Author(s):  
P. Janaki ◽  
R. Sudha ◽  
T.S. Sribharathi ◽  
P. Anitha ◽  
K. Poornima ◽  
...  

The adsorption performance of sulphuric acid treated low cost adsorbent synthesized by using Citrus limettioides peel as an effective raw material for the removal of cadmium(II) from water. The batch adsorption method was carried out to optimize some parameters like contact time, pH and adsorbent dose. The nonlinear isotherm equations were used to calculate the different isotherm constant of five isotherm models namely Freundlich, Langmuir, Dubinin-Radushkevich, Redlich-Peterson and Sips. The Langmuir monolayer adsorption capacity of chemically modified Citrus limettioides peel was found to be 287.60 mg g-1. The negative values of ΔGº and ΔHº showed that the adsorption process is spontaneous and exothermic.


Atmosphere ◽  
2019 ◽  
Vol 10 (4) ◽  
pp. 201 ◽  
Author(s):  
Yu Zou ◽  
Xue Jiao Deng ◽  
Tao Deng ◽  
Chang Qin Yin ◽  
Fei Li

Isoprene has a potentially large effect on ozone (O3) formation in the subtropical, highly polluted city of Guangzhou. Online measurements of isoprene in Guangzhou city are scarce; thus, isoprene levels were monitored for one year at the Guangzhou Panyu Atmospheric Composition Station (GPACS), a suburban site in Guangzhou, using an online gas chromatography-flame ionization detector (GC–FID) system to investigate the characterization and reactivity of isoprene and its effect on the O3 peak profile in different seasons. The results showed that the daily average mixing ratios of isoprene at GPACS were 0.40, 2.20, 1.40, and 0.13 mixing ratio by volume (ppbv) in spring, summer, autumn, and winter, respectively. These values were considerably higher than the mixing ratios of isoprene in the numerous other subtropical and temperate cities around the world. Furthermore, isoprene ranked first with regard to O3 formation potential (OFP) and propylene-equivalent mixing ratio among 56 measured non–methane hydrocarbons (NMHCs). The ratios of isoprene to cis-2-butene, an exhaust tracer, were determined to estimate the fractions of biogenic and anthropogenic emissions. The results revealed a much greater contribution from biogenic than anthropogenic factors during the daytime in all four seasons. In addition, night-time isoprene emissions were mostly associated with vehicles in winter, and the residual isoprene that remained after photochemical loss during the daytime also persisted into the night. The high levels of isoprene in summer and autumn may cause the strong and broad peaks of the O3 profile because of its association with the most favorable meteorological conditions (e.g., high temperature and intense solar radiation) and the highest OH mixing ratio, which could affect human health by exposing people to a high O3 mixing ratio for prolonged periods. The lower mixing ratios of isoprene resulted in a weak and sharp peak in the O3 profile in both spring and winter. The high level of isoprene in the subtropical zone could accentuate its large impact on atmospheric oxidant capacity and air quality in Guangzhou city.


2014 ◽  
Vol 809-810 ◽  
pp. 297-301
Author(s):  
Ping Rui Meng ◽  
Liang Bo Li

In order to selectively separate luteolin from its crude solution, we synthesized luteolin molecular imprinted polymers (LMIP) with high recognition specificity for luteolin, using an imprinting technique. Luteolin was used as template, methanol as solvent, and N,N’-methylenebisacrylamide (MBAA) as the cross-linking. Then prepared LMIP were characterized and evaluated by scanning electron microscope (SEM) and equilibrium absorption experiments. The results showed that the cavities matching with the template molecules in size and structure were present in the LMIP. Adsorption dynamics analysis suggested that, when the adsorption time reached 4 h, the adsorption process had reached balance and the adsorption capacity was at steady state. The selective adsorption amount reached at 35.65 umol/g for the LMIP, while a lower value of 11.68 umol/g for the blank polymer (i.e. nontemplated). Relative to the corresponding blank polymer, LMIP had an excellent recognition to luteolin in methanol solution. Keywords: Molecular imprinting, Molecular recognition, Adsorbent, Luteolin


2017 ◽  
Author(s):  
Khadak Singh Mahata ◽  
Maheswar Rupakheti ◽  
Arnico Kumar Panday ◽  
Piyush Bhardwaj ◽  
Manish Naja ◽  
...  

Abstract. Residents of the Kathmandu Valley experience severe particulate and gaseous air pollution throughout most of the year, even during much of the rainy season. The knowledge base for understanding the air pollution in the Kathmandu Valley was previously very limited, but is improving rapidly due to several field measurement studies conducted in the last few years. Thus far, most analyses of observations in the Kathmandu Valley have been limited to short periods of time at single locations. This study extends on the past studies by examining the spatial and temporal characteristics of two important gaseous air pollutant (CO and O3) based on simultaneous observations over a longer period at five locations within the valley and on its rim, including a supersite (at Bode in the valley center, 1345 m above sea level) and four satellite sites (at Paknajol, 1380 m asl in the Kathmandu city center, at Bhimdhunga (1522 m asl), a mountain pass on the valley's western rim, at Nagarkot (1901 m asl), another mountain pass on the eastern rim, and Naikhandi, near the valley's only river outlet). CO and O3 mixing ratios were monitored from January to July 2013, along with other gases and aerosol particles by instruments deployed at the Bode supersite during the international air pollution measurement campaign SusKat-ABC (Sustainable Atmosphere for the Kathmandu Valley – endorsed by the Atmospheric Brown Clouds program of UNEP). The O3 monitoring at Bode, Paknajol and Nagarkot as well as the CO monitoring at Bode were extended beyond July 2013 to investigate their variability over a complete annual cycle. Higher CO mixing ratios were found at Bode than at the outskirt sites (Bhimdhunga, Naikhandi and Nagarkot), and all sites except Nagarkot showed distinct diurnal cycles of CO mixing ratio with morning peaks and daytime lows. Seasonally, CO was higher during the pre-monsoon and winter seasons, especially due to the emissions from brick kiln industries, which only operate during this period, as well as increased domestic heating during winter, and regional forest fires and agro-residue burning. It was lower during the monsoon due to rainfall, which reduces open burning activities within the valley and in the surrounding regions, and thus reduces the sources of CO. The meteorology of the valley also played a key role in determining the CO mixing ratios. Furthermore, there was evidence of some influence of pollution from the greater region around the valley. A top-down estimate of the CO emission flux was made by using the CO mixing ratio and mixing layer height (MLH) measured at Bode. The estimated annual CO flux at Bode was 4.92 μg m−2 s−1, which is 2–14 times higher than that in widely used emission inventory databases (EDGAR HTAP, REAS and INTEX-B). This difference in CO flux between Bode and other emission databases likely arises from large uncertainties in both the top-down and bottom-up approaches to estimating the emission flux. The O3 mixing ratio was found to be highest during the pre-monsoon season at all sites, while the timing of the seasonal minimum varied across the sites. The daily maximum 8 hour average O3 exceeded the WHO recommended guideline of 50 ppb on more days at the hilltop station of Nagarkot (159/357 days) than at the urban valley bottom sites of Paknajol (132/354 days) and Bode (102/353 days), presumably due to the influence of free-tropospheric air at the high-altitude site, as well as to titration of O3 by fresh NOx emissions near the urban sites. More than 78 % of the exceedance days were during the pre-monsoon period at all sites. This was due to both favorable meteorological conditions as well as contributions of precursors from regional sources such as forest fires and agro-residue burning. The high O3 mixing ratio observed during the pre-monsoon period is of a high concern for human health and ecosystems, including agroecosystems in the Kathmandu Valley and surrounding regions.


2016 ◽  
Vol 45 (18) ◽  
pp. 7665-7671 ◽  
Author(s):  
Shanshan Guo ◽  
Shousi Lu ◽  
Pingxiang Xu ◽  
Yi Ma ◽  
Liang Zhao ◽  
...  

We report a biomimetic method to synthesize needle-like calcium phosphate (CaP) using carbon dots (CDs) and sodium carboxymethylcellulose as dual templates. The CaP/CDs were capable of cell labeling and selective detection of copper ions in drinking water.


Sign in / Sign up

Export Citation Format

Share Document