scholarly journals Factors influencing the adsorption and photocatalysis of direct red 80 in the presence of a TiO2: Equilibrium and kinetics modeling

2021 ◽  
pp. 174751982198996
Author(s):  
Moussa Abbas
Keyword(s):  
Elimination Rate ◽  
Threshold Value ◽  
Heterogeneous Photocatalysis ◽  
Order Kinetic ◽  
Batch Mode ◽  
Adsorption Capacities ◽  
Initial Ph ◽  
Equilibrium And Kinetics ◽  
Order Kinetic Model ◽  
Charge Point

Among the different photocatalysts, TiO2 ( Eg = 3.1 eV, zero charge point (pHpzc = 6.3), and surface = 55 m2/g) is currently the most efficient and the most studied semiconductor due to its strong photocatalytic activity, non-toxicity, and chemical stability. The elimination of DR-80 on TiO2 is studied by adsorption in batch mode and by application of heterogeneous photocatalysis onto TiO2 under UV irradiation. The effects of contact time (0–60 min), initial pH (3–11), dose of the adsorbent (0.5–3 g L−1), and DR-80 concentration (40–60 mg L−1) on the adsorption of DR-80 by TiO2 are studied for optimization of these parameters. The kinetic parameters, rate constants, and equilibrium adsorption capacities are calculated and discussed for each applied theoretical model. The adsorption of DR-80 is well described by the pseudo-first-order kinetic model. The fitting of the adsorption isotherms shows that the models of Langmuir and Temkin offering a better fit and an adsorption 64.102 mg/g at 25 °C of DR-80 are eliminated. The results showed that the photocatalytic efficiency strongly depends on the pH while the initial rate of photodegradation is proportional to the catalyst dose, and becomes almost constant above a threshold value. It was found that the photodegradation is favored at low DR-80 concentrations in accordance with the Langmuir–Hinshelwood model with the constants Kad = 6.5274 L/mg and KL–H = 0.17818 mg L−1 min. However, the adsorption is improved for high DR-80 concentrations. It is found that the degradation depends on both the temperature and the pH with a high elimination rate at high temperature. The photocatalyst TiO2 has a better activity for the degradation of DR-80, compared to some commercial catalysts that have been described in the literature.

Biosorption of hexavalent chromium from aqueous solution by polyethyleneimine-modified ultrasonic-assisted acid hydrochar from Sargassum horneri

2020 ◽  
Vol 81 (6) ◽  
pp. 1114-1129 ◽  
Author(s):  
Jun Wang ◽  
Qinglong Xie ◽  
Ao Li ◽  
Xuejun Liu ◽  
Fengwen Yu ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Batch Adsorption ◽  
Crosslinking Reaction ◽  
Order Kinetic ◽  
Adsorption Capacities ◽  
Initial Ph ◽  
Ultrasonic Assisted ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Abstract In this study, an efficient route to synthesizing polyethyleneimine-modified ultrasonic-assisted acid hydrochar (PEI-USAH) is developed and reported. Ultrasonic irradiation technique was used as surface modification method to shorten the crosslinking reaction for hydrochar and polyethyleneimine (PEI). The PEI-USAH showed an excellent adsorption capacity for Cr(VI) from aqueous solution. The physicochemical properties of this PEI-modified adsorbent were comparatively characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller analysis and CNHS analysis. The effects of contact time, initial pH, and biosorbent dose on adsorption capacities were investigated. The batch adsorption experiments showed that PEI-USAH possessed the maximum adsorption capacities of 94.38 mg/g and 330.84 mg/g for initial Cr(VI) concentration of 100 mg/L and 500 mg/L, respectively. Furthermore, this adsorption process could be fitted to Langmuir adsorption and described by the pseudo second order kinetic model. Based on the above findings, PEI-USAH could be used as a potential adsorbent for removal of Cr(VI) from wastewater.

scholarly journals Comparative Studies of the Adsorption of Direct Dye on Activated Carbon and Conducting Polymer Composite

2012 ◽  
Vol 9 (3) ◽  
pp. 1122-1134 ◽  
Author(s):  
J. Raffiea Baseri ◽  
P. N. Palanisamy ◽  
P. Sivakumar
Keyword(s):  
Activated Carbon ◽  
Polymer Composite ◽  
Order Kinetic ◽  
Batch Mode ◽  
Adsorption Capacities ◽  
Direct Blue ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Direct Dye ◽  
Adsorptive Properties

This study analyses the feasibility of removing Direct Blue 71 from aqueous solution by different adsorbents such as activated carbon (TPAC) and Poly pyrrole polymer composite (PPC) prepared fromThevetia Peruviana. Batch mode adsorption was performed to investigate the adsorption capacities of these adsorbents by varying initial dye concentration, temperature, agitation time and pH. The performance of TPAC was compared with PPC. Among the adsorbents, PPC had more adsorption capacity (88.24%) than TPAC (58.82%) at an initial concentration of 50 mg/L and at 30°C. The experimental data best fitted with pseudo second order kinetic model. The adsorption data fitted well for Langmuir adsorption isotherm. Thermodynamic parameters for the adsorbents were also evaluated. The carbon embedded in conducting polymers matrix show better adsorptive properties than activated carbon.

scholarly journals Thermally activated persulfate treatment and mineralization of a recalcitrant high TDS petrochemical wastewater

2017 ◽  
Vol 19 (2) ◽  
pp. 72-77 ◽  
Author(s):  
Sahand Jorfi ◽  
Sudabeh Pourfadakari ◽  
Mehdi Ahmadi ◽  
Hamideh Akbari
Keyword(s):  
Ph Value ◽  
Cod Removal ◽  
Order Kinetic ◽  
Operational Parameters ◽  
Batch Mode ◽  
Thermally Activated ◽  
Toc Removal ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Activated Persulfate

Abstract Thermally activated persulfate efficiency for the treatment of a recalcitrant high TDS wastewater was investigated. The specific character of studied wastewater was high TDS content of around 23820 mg/L and BOD5/COD ratio of 0.07. Effective operational parameters including initial pH values of 3–9, reaction temperature of 40–80°C and persulfate concentrations of 0.5–5 g/L for COD removal were investigated in batch mode experiments. Removal efficiency was pH and temperature dependent. The COD and TOC removal of 94.3% and 82.8% were obtained at persulfate concentration of 4 g/L, initial pH value of 5 and temperature of 70°C after 180 min for initial COD concentration of 1410 mg/L. The pseudo first-order kinetic model was best fitted with COD removal (R2 = 0.94).

Chitosan-based Magnetic Composites - Efficient Adsorbents for Removal of Pb(II) and Cu(II) from Aqueous Mono and Bicomponent Solutions

2018 ◽  
Vol 69 (9) ◽  
pp. 2323-2330 ◽  
Author(s):  
Daniela C. Culita ◽  
Claudia Maria Simonescu ◽  
Rodica Elena Patescu ◽  
Nicolae Stanica
Keyword(s):  
Aqueous Solutions ◽  
Metal Ions ◽  
Chemical Properties ◽  
Order Kinetic ◽  
Mass Ratio ◽  
Magnetic Adsorbent ◽  
Magnetic Composites ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Physical And Chemical

A series of three chitosan-based magnetic composites was prepared through a simple coprecipitation method. It was investigated the influence of mass ratio between chitosan and magnetite on the physical and chemical properties of the composites in order to establish the optimum conditions for obtaining a composite with good adsorption capacity for Pb(II) and Cu(II) from mono and bicomponent aqueous solutions. It was found that the microspheres prepared using mass ratio chitosan / magnetite 1.25/1, having a saturation magnetization of 15 emu g--1, are the best to be used as adsorbent for the metal ions. The influence of different parameters such as initial pH values, contact time, initial concentration of metal ions, on the adsorption of Pb(II) and Cu(II) onto the chitosan-based magnetic adsorbent was investigated in details. The adsorption process fits the pseudo-second-order kinetic model in both mono and bicomponent systems, and the maximum adsorption capacities calculated on the basis of the Langmuir model were 79.4 mg g--1 for Pb(II) and 48.5 mg g--1 for Cu(II) in monocomponent systems, while in bicomponent systems were 88.3 and 49.5 mg g--1, respectively. The results revealed that the as prepared chitosan-based magnetic adsorbent can be an effective and promising adsorbent for Pb(II) and Cu(II) from mono and bicomponent aqueous solutions.

scholarly journals The sorption of inorganic arsenic on modified sepiolite: Effect of hydrated iron(III)-oxide

2014 ◽  
Vol 79 (7) ◽  
pp. 815-828 ◽  
Author(s):  
Nikola Ilic ◽  
Slavica Lazarevic ◽  
Vladana Rajakovic-Ognjanovic ◽  
Ljubinka Rajakovic ◽  
Djordje Janackovic ◽  
...  
Keyword(s):  
Sorption Capacity ◽  
Arsenic Removal ◽  
Ph Value ◽  
Inorganic Arsenic ◽  
Arsenic Species ◽  
Deionized Water ◽  
Order Kinetic ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The sorption of inorganic arsenic species, As(III) and As(V), from water by sepiolite modified with hydrated iron(III) oxide was investigated at 25 ?C through batch studies. The influence of the initial pH value, the initial As concentrations, the contact time and types of water on the sorption capacity was investigated. Two types of water were used, deionized and groundwater. The maximal sorption capacity for As(III) from deionized water was observed at initial and final pH value 7.0, while the bonding of As(V) was observed to be almost pH independent for pH value in the range from 2.0 to 7.0, and the significant decrease in the sorption capacity was observed at pH values above 7.0. The sorption capacity at initial pH 7.0 was about 10 mg g?1 for As(III) and 4.2 mg g?1 for As(V) in deionized water. The capacity in groundwater was decreased by 40 % for As(III) and by 20 % for As(V). The Langmuir model and pseudo-second order kinetic model revealed good agreement with the experimental results. The results show that Fe(III)-modified sepiolite exhibits significant affinity for arsenic removal and it has a potential for the application in water purification processes.

Adsorption of Chromium (VI) from Aqueous Solution by Agricultural Waste Derived Activated Carbon

2013 ◽  
Vol 726-731 ◽  
pp. 2100-2106 ◽  
Author(s):  
Hua Zhang ◽  
Xue Hong Zhang ◽  
Yi Nian Zhu ◽  
Shou Rui Yuan
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Agricultural Waste ◽  
Order Kinetic ◽  
Chromium Vi ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Grapefruit Peel ◽  
Pseudo Second Order ◽  
C 30

Activated carbon prepared from grapefruit peel, an agricultural solid waste by-product, has been used for the adsorption of Cr(VI) from aqueous solution. The effects of adsorbent dosage, pH and temperature on adsorption of Cr(VI) were investigated. The maximum adsorption yield was obtained at the initial pH of 3. The dynamical data fit very well with the pseudo-second-order kinetic model and the calculated adsorption capacities (23.98, 24.33 and 24.81 mg/g) were in good agreement with experiment results at 20°C, 30°C and 40 °C for the 100 mg/L Cr(VI) solution. The Freundlich model (R2 values were 0.9198-0.9871) fitted adsorption data better than the Langmuir model. The calculated parameters confirmed the favorable adsorption of Cr(VI) on the activated carbon prepared from grapefruit peel.

scholarly journals Simultaneous removal of cationic and anionic dyes from aqueous solution by double functional groups modified bagasse

2020 ◽  
Vol 82 (10) ◽  
pp. 2159-2167
Author(s):  
Ru-yi Zhou ◽  
Jun-xia Yu ◽  
Ru-an Chi
Keyword(s):  
Aqueous Solution ◽  
Functional Groups ◽  
Order Kinetic ◽  
Anionic Dyes ◽  
Adsorption Capacities ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Amine Groups ◽  
Modified Adsorbents ◽  
Zeta Potential Analysis

Abstract Double functional groups modified bagasse (DFMBs), a series of new zwitterionic groups of carboxyl and amine modified adsorbents, were prepared through grafting tetraethylenepentamine (TEPA) onto the pyromellitic dianhydride (PMDA) modified bagasse using the DCC/DMAP method. DFMBs' ability to simultaneously remove basic magenta (BM, cationic dye) and Congo red (CR, anionic dye) from aqueous solution in single and binary dye systems was investigated. FTIR spectra and Zeta potential analysis results showed that PMDA and TEPA were successfully grafted onto the surface of bagasse, and the ratio of the amount of carboxyl groups and amine groups was controlled by the addition of a dosage of TEPA. Adsorption results showed that adsorption capacities of DFMBs for BM decreased while that for CR increased with the increase of the amount of TEPA in both single and binary dye systems, and BM or CR was absorbed on the modified biosorbents was mainly through electrostatic attraction and hydrogen bond. The adsorption for BM and CR could reach equilibrium within 300 min, both processes were fitted well by the pseudo-second-order kinetic model. The cationic and anionic dyes removal experiment in the binary system showed that DMFBs could be chosen as adsorbents to treat wastewater containing different ratios of cationic and anionic dyes.

Equilibrium and Kinetic Studies for the Biosorption of Aqueous Nickel(II) Ions onto the Pseudomonas alcaligenes Biomass

2010 ◽  
Vol 171-172 ◽  
pp. 41-44
Author(s):  
Xiao Cun Xiao ◽  
Gai Xia Fang ◽  
Er Li Zhao ◽  
Lv Bin Zhai ◽  
Jun Shuai Shi
Keyword(s):  
Industrial Wastewater ◽  
Chemical Interaction ◽  
Kinetic Studies ◽  
Synthetic Wastewater ◽  
Order Kinetic ◽  
Adsorption Capacities ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Pseudomonas Alcaligenes ◽  
Batch Biosorption

The objective of this study is to assess the environmentaly friendly Ni(II) adsorption from synthetic wastewater using Pseudomonas alcaligenes biomass (PA-2). The ability of PA-2 to remove the Ni(II) ions was investigated by using batch biosorption procedure. The effects such as pH, dosage of biosorbent, Ni(II) initial concentration and sorbate–sorbent contact time and agitating speed on the adsorption capacities of PA-2 were studied. Biosorption equilibriums were rapidly established in about 60 min and the adsorption kinetics followed the pseudo-second order kinetic model. The maximum Ni(II) adsorption capacity determined from Langmuir isotherm were 82.23 mg/g PA-2 at pH 5.0, at 25±2°C and shaker speed 150 rpm, respectively. The carboxyl , hydroxyl and amino groups of the PA-2 were involved in chemical interaction with the Ni(II) ions depicted by Fourier transform infrared spectroscopic (FTIR) results. The study points to the potential of new use of Pseudomonas alcaligenes biomass as an effective biosorbent for the removal of Ni(II) and from environmental and industrial wastewater.

scholarly journals Adsorption of Cr(VI) ions onto goethite, activated carbon and their composite: kinetic and thermodynamic studies

2020 ◽  
Vol 10 (9) ◽  
Author(s):  
G. B. Adebayo ◽  
H. I. Adegoke ◽  
Sidiq Fauzeeyat
Keyword(s):  
Activated Carbon ◽  
Heavy Metal Contamination ◽  
Stem Bark ◽  
Order Kinetic ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Daniellia Oliveri ◽  
Kinetic And Thermodynamic Studies

Abstract Hexavalent chromium was adsorbed from aqueous solution with three prepared and characterized adsorbents, namely goethite (G), activated carbon (AC) and their composite (GAC). The goethite particle was synthesized using the precipitation methods, and activated carbon was prepared from the stem bark of Daniellia oliveri tree and composite in a ratio of 1:5 goethite–activated carbon. The adsorption capacities of G, AC and GAC for Cr(VI) are 6.627, 5.455 and 6.354 mg/g with 0.02 g adsorbent within contact time of 60, 180 and 30 min for G, AC and GAC, respectively, for Cr(VI) adsorption at optimum pH of 3. The isotherm studied was best explained by Langmuir adsorption isotherm and fitted with the pseudo-second-order kinetic model. Desorption studies showed that 1.0 M HNO3 was a better desorbing agent than 0.1 M HNO3, 0.1 M HCl and 1.0 M HCl. Chromium was most desorbed (94.60% in Cr//G using 1 M HNO3). The result obtained revealed that goethite and activated carbon produced are favourable adsorbents and the composite of the two adsorbents gives a more favourable, economical and affordable adsorbent for the clean-up of heavy metal contamination.

scholarly journals Adsorption characteristics of Pb(II) using biochar derived from spent mushroom substrate

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Qianlan Wu ◽  
Yang Xian ◽  
Zilin He ◽  
Qi Zhang ◽  
Jun Wu ◽  
...  
Keyword(s):  
Physicochemical Properties ◽  
Raw Materials ◽  
Edible Mushroom ◽  
Bet Surface Area ◽  
Order Kinetic ◽  
The Sustainable Development ◽  
Adsorption Capacities ◽  
Small Pore ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Abstract As a multifunctional material, biochar is considered a potential adsorbent for removing heavy metals from wastewater. Most biochars with high adsorption capacities have been modified, but this modification is uneconomical, and modifying biochar may cause secondary pollution. Thus, it is necessary to develop an efficient biochar without modification. In this study, spent P. ostreatus substrate and spent shiitake substrate were used as the raw materials to prepare biochar. Then, the physicochemical properties of the biochars and their removal efficiencies for Pb(II) were investigated. The results showed that the physicochemical properties (e.g., large BET surface area, small pore structure and abundant functional groups) contributed to the large adsorption capacity for Pb(II); the maximum adsorption capacities were 326 mg g−1 (spent P. ostreatus substrate-derived biochar) and 398 mg g−1 (spent shiitake substrate-derived biochar), which are 1.6–10 times larger than those of other modified biochars. The Pb(II) adsorption data could be well described by the pseudo-second-order kinetic model and the Langmuir model. This study provides a new method to comprehensively utilize spent mushroom substrates for the sustainable development of the edible mushroom industry.

Sign in / Sign up

Export Citation Format

Share Document