Research Note: Average Friction Coefficients in Gears

1975 ◽  
Vol 17 (6) ◽  
pp. 360-362 ◽  
Author(s):  
A. C. Rao

Variation in sliding velocity—both in magnitude and direction—during a meshing cycle, the load distribution among the pairs of teeth, and the accuracy with which teeth are cut are some of the factors that make the mathematical analysis of friction in gear teeth extremely difficult. Of these, sliding velocity, which is responsible for the formation of an oil film between the teeth, plays an important role, and any attempt to determine the friction coefficients must take account of changes in sliding velocity. In this note an expression has been developed, considering the variation in sliding velocity, for power loss in terms of the coefficient of friction and gear parameters. The experimental results are compared with those obtained by other methods.

1981 ◽  
Vol 103 (1) ◽  
pp. 73-82 ◽  
Author(s):  
H. Winter ◽  
H. Wilkesmann

The formulae of classical hydrodynamics are not suitable for the calculation of load capacity and power loss of worm gear drives. Thus a theoretical basis had to be developed for the comparison of different tooth profiles, materials of worm and worm wheel and lubricants. The data obtained were compared with test results. It proved that the coefficient of friction is an important influence factor.


2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Myeong-Woo Ha ◽  
Kwang-Hee Lee ◽  
Chul-Hee Lee ◽  
Jong-Myung Choi ◽  
Jun-Wook An

The dispenser ejects the ceramic filler and phosphor-containing liquid for making various products. When the particle-containing liquid is ejected under high-velocity conditions, however, the ejection reliability decreases because of the wear of the contact surface between the rod and nozzle even though these components are made of hard materials. It is therefore necessary to characterize the friction and wear properties of the hard materials, tungsten carbide (WC) and zirconium (Zr), with the high-viscosity liquid-containing nitride or yttrium aluminum garnet (YAG) particles under reciprocating conditions. Particle contents of 15 wt.% and 30 wt.% are added to the liquid. A reciprocating test was implemented to this end, and WC and Zr specimens were used. The liquid used in the experiment contains nitride and YAG. The experimental results show that the particles inside the liquid are worn out, leading to particle lubrication and the decrease in the coefficient of friction. Also, it is confirmed that the more the particles are, the less the coefficient of friction is due to particle lubrication. For each experimental condition, the coefficient of friction is measured and compared. Moreover, the contact surface of the specimen is analyzed using an electron microscope, and a profilometer is used to measure the surface roughness of the specimen before and after the test. The reciprocation friction and wear characteristics of WC and Zr with phosphor-containing liquid are evaluated by analyzing the experimental results.


2013 ◽  
Vol 10 (80) ◽  
pp. 20120467 ◽  
Author(s):  
Michael J. Adams ◽  
Simon A. Johnson ◽  
Philippe Lefèvre ◽  
Vincent Lévesque ◽  
Vincent Hayward ◽  
...  

Many aspects of both grip function and tactile perception depend on complex frictional interactions occurring in the contact zone of the finger pad, which is the subject of the current review. While it is well established that friction plays a crucial role in grip function, its exact contribution for discriminatory touch involving the sliding of a finger pad is more elusive. For texture discrimination, it is clear that vibrotaction plays an important role in the discriminatory mechanisms. Among other factors, friction impacts the nature of the vibrations generated by the relative movement of the fingertip skin against a probed object. Friction also has a major influence on the perceived tactile pleasantness of a surface. The contact mechanics of a finger pad is governed by the fingerprint ridges and the sweat that is exuded from pores located on these ridges. Counterintuitively, the coefficient of friction can increase by an order of magnitude in a period of tens of seconds when in contact with an impermeably smooth surface, such as glass. In contrast, the value will decrease for a porous surface, such as paper. The increase in friction is attributed to an occlusion mechanism and can be described by first-order kinetics. Surprisingly, the sensitivity of the coefficient of friction to the normal load and sliding velocity is comparatively of second order, yet these dependencies provide the main basis of theoretical models which, to-date, largely ignore the time evolution of the frictional dynamics. One well-known effect on taction is the possibility of inducing stick–slip if the friction decreases with increasing sliding velocity. Moreover, the initial slip of a finger pad occurs by the propagation of an annulus of failure from the perimeter of the contact zone and this phenomenon could be important in tactile perception and grip function.


1961 ◽  
Vol 83 (4) ◽  
pp. 523-529 ◽  
Author(s):  
C. T. Yang

Split-die technique was adopted to find the coefficient of friction in wire drawing directly from experiment. Simple dynamometers with wire resistance strain gages were used for measuring separating force and drawing force instead of cumbersome equipment used by former researchers. Reasonably good results were obtained. The effect of the land or parallel portion in the die on the coefficient of friction was indicated in the results. Its importance was emphasized. A theoretical equation of the drawing stress with the effect of land considered was derived. Using the coefficient of friction obtained by the split-die method, drawing stresses were calculated from the derived equation. A comparison of the theoretical and experimental drawing stresses was made. Results were tabulated and plotted. It was concluded that including the land in the analysis of wire drawing is important and further research in analyzing the shear deformation must be pursued in order to get a close agreement between theoretical analysis and experimental results.


2021 ◽  
Author(s):  
Joseba Cillaurren ◽  
Lander Galdos ◽  
Mario Sanchez ◽  
Alaitz Zabala ◽  
Eneko Saenz de Argandoña ◽  
...  

In the last few years many efforts have been carried out in order to better understand what the real contact between material and tools is. Based on the better understanding new friction models have been developed which have allowed process designers to improve numerical results in terms of component viability and geometrical accuracy. The new models define the coefficient of friction depending on different process parameters such as the contact pressure, the sliding velocity, the material strain, and the tool temperature. Many examples of the improvements achieved, both at laboratory scale and at industrial scale, can be found in the recent literature. However, in each of the examples found in the literature, different ranges of the variables affecting the coefficient of friction are covered depending on the component analysed and the material used to produce such component. The present work statistically analyses the contact pressure and sliding velocity ranges achieved during numerical simulation (FEM) of sheet metal forming processes. Nineteen different industrial components representing a high variety of shapes have been studied to cover a wide range of casuistic. The contact pressure and sliding velocity corresponding to typical areas of the tooling have been analysed though numerical simulation in each case. This study identifies the ranges of contact-pressure and sliding velocities occurring in sheet metal forming aimed to set the characterization range for future friction studies.


1985 ◽  
Vol 13 (1) ◽  
pp. 41-64
Author(s):  
W. R. Garrott ◽  
D. A. Guenther

Abstract An experimental study was made to compare the validities of methods currently used by accident reconstructionists to determine the coefficient of friction between the road and the vehicle tires at the time of an incident. This value could then be used in conjunction with skid mark length and vehicle weight to calculate the prebraking speed of the vehicle. Three automobiles and three trucks with a variety of tires and loadings were used on a variety of pavements. The accuracy and area of applicability of each of four methods for obtaining friction coefficients were determined by relating the prebraking speed calculated from each to the actual speed at the time of brake application. All four methods were satisfactory for automobiles and the pickup truck used, but only two were acceptable for heavy trucks. The most valid coefficients are obtained from skid mark lengths obtained under conditions duplicating those in an incident.


2010 ◽  
Vol 26-28 ◽  
pp. 320-325 ◽  
Author(s):  
Li Li Wang ◽  
Dong Sheng Li ◽  
Xiao Qiang Li ◽  
Liang Wang ◽  
Wei Jun Yang

Stretch forming process of aircraft skin over reconfigurable compliant tooling is a new technology in skin manufacturing. During this process, the coefficient of friction is important for modeling accurately the process of stretch forming. The objective of this research is to measure the coefficient of friction for aluminum alloy in contact with polyurethane rubber in reciprocal sliding. An orthogonal experimental design was used to reveal the impact of four factors on the coefficient of friction, including lubrication, normal load, aluminum alloy material and sliding velocity. It is shown that lubrication is a major factor, sliding velocity is a minor factor. The influence of normal pressure is less than sliding velocity and the influence of aluminum alloy material is not very obvious. Finally, based on the experiment results, the selections of lubricant and stretching velocity are discussed in order to improve the process of stretch forming.


1908 ◽  
Vol 28 ◽  
pp. 374-381 ◽  
Author(s):  
G. H. Gulliver

SUMMARY(a) On the assumptions that resistance to deformation is due to simple friction, and that the coefficient of friction is independent of the load, the ratio of the yield point in tension to the yield point in compression, for what is ordinarily known as mild steel, is calculated as 2·384 to 3·384, or as 0·705 to 1. Experimental results so far obtained do not agree well with these figures, the value for the tensile yield point being relatively high, and that for compression relatively low.(b) On the further assumption that a cohesive force acting between the metallic particles gives rise to a frictional resistance which may be added (algebraically) to that due to the effect of the external load, the value of this cohesive force is deduced as equal to 3·384 times the stress which corresponds with the tension yield point, or to 2·384 times that corresponding with the compression yield point. Experimental results from a large number of tests agree very fairly with the calculated figures for the case of tension.


1968 ◽  
Vol 90 (1) ◽  
pp. 65-71 ◽  
Author(s):  
E. F. Finkin

A mathematical analysis is offered showing the various consequences of spline friction in multiple disk systems. Included are equations for the load variation through a multiple disk pack, the effect of interfacial pressure distribution on this load variation, the torque variation through a pack, and the total torque carried by a pack. The relation between friction and velocity is taken into account. The coefficient of friction determined from the data of a multiple disk test apparatus, ignoring spline friction, is shown to be significantly in error and an equation is derived for calculating the true coefficients of friction. Examples of the load variation in a pack are derived and the results plotted.


1978 ◽  
Vol 100 (1) ◽  
pp. 25-30
Author(s):  
D. H. Offner ◽  
N. Tomita

A method and testing device for determining a coefficient of friction for rolling disks is described. The method equates the energy of rolling resistance to the change in potential energy of a moving system. The experimental results of applying this method to steel, aluminum, and plexiglass disks of 3.8, 2.5, and 1.7 cm radii and 1 cm width rolling on steel and aluminum bases are summarized. An empirical relationship between the coefficient of friction and energy of surface deformation is presented. Use of device for determining the static coefficient of friction for impending rolling and sliding of disks is discussed.


Sign in / Sign up

Export Citation Format

Share Document