Using of Sukary and Khlass Date Pits as a Bio-adsorbents for Adsorption of Lead and Copper Ions from Waste Water

2021 ◽  
Vol 37 (2) ◽  
pp. 302-307
Author(s):  
Abdulrahman G. Alhamzan

In this study date pits of two types of date-palm trees (Phoenix Dactylifera L.), in Saudi Arabia were used as bio-sorbents for heavy metals (e.g. lead and copper) from aqueous solutions. Investigation of equilibrium time and the effect of different concentrations of metals were performed. Adsorption capacity of bio-sorbents increased when increasing concentration of metal ions. Maximum adsorption capacity at room temperature of Sukary date pits was 17.53 mg g-1 and 9.86 mg g-1 for lead and copper ions, respectively. Whereas, Khlass date pits showed maximum adsorption capacity at 14.1 mg g-1 and 7.91 mg g-1 for lead and copper ions, respectively at room temperature. Equilibrium isotherm models, (Langmuir and Freundlich models), were used for analysis of equilibrium experimental results. these models describe the experimental data well.

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 63
Author(s):  
Maria Harja ◽  
Gabriela Buema ◽  
Nicoleta Lupu ◽  
Horia Chiriac ◽  
Dumitru Daniel Herea ◽  
...  

Fly ash/magnetite material was used for the adsorption of copper ions from synthetic wastewater. The obtained material was characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET) surface area, and vibrating sample magnetometer (VSM). Batch adsorption experiments were employed in order to investigate the effects of adsorbent dose, initial Cu (II) concentration and contact time over adsorption efficiency. The experimental isotherms were modeled using Langmuir (four types of its linearization), Freundlich, Temkin, and Harkins–Jura isotherm models. The fits of the results are estimated according to the Langmuir isotherm, with a maximum adsorption capacity of 17.39 mg/g. The pseudo-second-order model was able to describe kinetic results. The data obtained throughout the study prove that this novel material represents a potential low-cost adsorbent for copper adsorption with improved adsorption capacity and magnetic separation capability compared with raw fly ash.


Molecules ◽  
2019 ◽  
Vol 24 (18) ◽  
pp. 3377 ◽  
Author(s):  
Mohamed A. Farag ◽  
Asmaa M. Otify ◽  
Aly M. El-Sayed ◽  
Camilia G. Michel ◽  
Shaimaa A. ElShebiney ◽  
...  

Interest in developing coffee substitutes is on the rise, to minimizing its health side effects. In the Middle East, date palm (Phoenix dactylifera L.) pits are often used as a coffee substitute post roasting. In this study, commercially-roasted date pit products, along with unroasted and home-prepared roasted date pits, were subjected to analyses for their metabolite composition, and neuropharmacological evaluation in mice. Headspace SPME-GCMS and GCMS post silylation were employed for characterizing its volatile and non-volatile metabolite profile. For comparison to roasted coffee, coffee product was also included. There is evidence that some commercial date pit products appear to contain undeclared additives. SPME headspace analysis revealed the abundance of furans, pyrans, terpenoids and sulfur compounds in roasted date pits, whereas pyrroles and caffeine were absent. GCMS-post silylation employed for primary metabolite profiling revealed fatty acids’ enrichment in roasted pits versus sugars’ abundance in coffee. Biological investigations affirmed that date pit showed safer margin than coffee from its LD50, albeit it exhibits no CNS stimulant properties. This study provides the first insight into the roasting impact on the date pit through its metabolome and its neuropharmacological aspects to rationalize its use as a coffee substitute.


Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3718
Author(s):  
Mohammad Azam ◽  
Saikh Mohammad Wabaidur ◽  
Mohammad Rizwan Khan ◽  
Saud I. Al-Resayes ◽  
Mohammad Shahidul Islam

The aim of the research was to prepare low-cost adsorbents, including raw date pits and chemically treated date pits, and to apply these materials to investigate the adsorption behavior of Cr(III) and Cd(II) ions from wastewater. The prepared materials were characterized using SEM, FT-IR and BET surface analysis techniques for investigating the surface morphology, particle size, pore size and surface functionalities of the materials. A series of adsorption processes was conducted in a batch system and optimized by investigating various parameters such as solution pH, contact time, initial metal concentrations and adsorbent dosage. The optimum pH for achieving maximum adsorption capacity was found to be approximately 7.8. The determination of metal ions was conducted using atomic adsorption spectrometry. The experimental results were fitted using isotherm Langmuir and Freundlich equations, and maximum monolayer adsorption capacities for Cr(III) and Cd(II) at 323 K were 1428.5 and 1302.0 mg/g (treated majdool date pits adsorbent) and 1228.5 and 1182.0 mg/g (treated sagai date pits adsorbent), respectively. It was found that the adsorption capacity of H2O2-treated date pits was higher than that of untreated DP. Recovery studies showed maximal metal elution with 0.1 M HCl for all the adsorbents. An 83.3–88.2% and 81.8–86.8% drop in Cr(III) and Cd(II) adsorption, respectively, were found after the five regeneration cycles. The results showed that the Langmuir model gave slightly better results than the Freundlich model for the untreated and treated date pits. Hence, the results demonstrated that the prepared materials could be a low-cost and eco-friendly choice for the remediation of Cr(III) and Cd(II) contaminants from an aqueous solution.


2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.


2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dhiraj Dutta ◽  
Jyoti Prasad Borah ◽  
Amrit Puzari

Results of investigation on adsorption of Mn2+ from aqueous solution by manganese oxide-coated hollow polymethylmethacrylate microspheres (MHPM) are reported here. This is the first report on Mn-coated hollow polymer as a substitute for widely used materials like green sand or MN-coated sand. Hollow polymethylmethacrylate (HPM) was prepared by using a literature procedure. Manganese oxide (MnO) was coated on the surface of HPM (MHPM) by using the electroless plating technique. The HPM and MHPM were characterized by using optical microscopy (OM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Optical and scanning micrographs were used to monitor the surface properties of the coated layer which revealed the presence of MnO on the surface of HPM. TGA showed the presence of 4-5% of MnO in MHPM. Adsorption isotherm studies were carried out as a function of pH, initial ion concentration, and contact time, to determine the adsorption efficiency for removal of Mn2+ from contaminated water by the synthesized MHPM. The isotherm results showed that the maximum adsorption capacity of MnO-coated HPM to remove manganese contaminants from water is 8.373 mg/g. The obtained R 2 values of Langmuir isotherm and Freundlich isotherm models were 1 and 0.87, respectively. Therefore, R 2 magnitude confirmed that the Langmuir model is best suited for Mn2+ adsorption by a monolayer of MHPM adsorbent. The material developed shows higher adsorption capacity even at a higher concentration of solute ions, which is not usually observed with similar materials of this kind. Overall findings indicate that MHPM is a very potential lightweight adsorbent for removal of Mn2+ from the aqueous solution because of its low density and high surface area.


2020 ◽  
Vol 10 (5) ◽  
pp. 1738
Author(s):  
Kay Thwe Aung ◽  
Seung-Hee Hong ◽  
Seong-Jik Park ◽  
Chang-Gu Lee

Polyacrylonitrile (PAN) fibers were prepared via electrospinning and were modified with diethylenetriamine (DETA) to fabricate surface-modified PAN fibers. The surface-modified PAN fibers were used to evaluate their adsorption capacity for the removal of Cu(II) from aqueous solutions. Batch adsorption experiments were performed to examine the effects of the modification process, initial concentration, initial pH, and adsorbent dose on the adsorption of Cu(II). Kinetic analysis revealed that the experimental data fitted the pseudo-second-order kinetic model better than the pseudo-first-order model. Adsorption equilibrium studies were conducted using the Freundlich and Langmuir isotherm models, and the findings indicated that the PAN fibers modified with 85% DETA presented the highest adsorption capacity for Cu(II) of all analyzed samples. Moreover, the results revealed that the Freundlich model was more appropriate than the Langmuir one for describing the adsorption of Cu(II) onto the modified fibers at various initial Cu(II) concentrations. The maximum adsorption capacity was determined to be 87.77 mg/g at pH 4, and the percent removal of Cu(II) increased as the amount of adsorbent increased. Furthermore, the surface-modified PAN fibers could be easily regenerated using NaOH solution. Therefore, surface-modified PAN fibers could be used as adsorbents for the removal of Cu(II) from aqueous solutions.


2018 ◽  
Vol 78 (7) ◽  
pp. 1615-1623 ◽  
Author(s):  
N. Priyantha ◽  
H. K. W. Sandamali ◽  
T. P. K. Kulasooriya

Abstract Although rice husk (RH) is a readily available, natural, heavy metal adsorbent, adsorption capacity in its natural form is insufficient for certain heavy metal ions. In this context, the study is based on enhancement of the adsorption capacity of RH for Cu(II). NaOH modified rice husk (SRH) shows higher extent of removal for Cu(II) ions than that of heated rice husk (HRH) and HNO3 modified rice husk (NRH). The extent of removal of SRH is increased with the concentration of NaOH, and the optimum NaOH concentration is 0.2 mol dm−3, used to modify rice husk for further studies. The surface area of SRH is 215 m2 g−1, which is twice as much as that of HRH according to previous studies. The sorption of Cu(II) on SRH obeys the Langmuir adsorption model, leading to the maximum adsorption capacity of 1.19 × 104 mg kg−1. Kinetics studies show that the interaction of Cu(II) with SRH obeys pseudo second order kinetics. The X-ray fluorescence spectroscopy confirms the adsorption of Cu(II) on SRH, while desorption studies confirm that Cu(II) adsorbed on SRH does not leach it back to water under normal conditions.


2015 ◽  
Vol 2015 ◽  
pp. 1-9
Author(s):  
Swarup Biswas ◽  
Umesh Mishra

Calcium pretreatedHevea brasiliensissawdust has been used as an effective and efficient adsorbent for the removal of copper ion from the contaminated water. Batch experiment was conducted to check the effect of pH, initial concentration, contact time, and adsorbent dose. The results conclude that adsorption capacity of adsorbent was influenced by operating parameters. Maximum adsorption capacity found from the batch adsorption process was 37.74 mg/g at pH of 5.6. Various isotherm models like Langmuir, Freundlich, and Temkin were used to compare the theoretical and experimental data, whereas the pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were applied to study the kinetics of the batch adsorption process. Dynamic studies were also conducted in packed-bed column using different bed depths and the maximum adsorption capacity of 34.29 was achieved. Characterizations of the adsorbent were done by Fourier transform infrared spectroscopy, scanning electron microscope, and energy dispersive X-ray spectroscopy.


2013 ◽  
Vol 68 (8) ◽  
pp. 1873-1879 ◽  
Author(s):  
Chongxia Wang ◽  
Qingping Song ◽  
Jiangang Gao

N-carboxymethyl chitosan (NCMC) was prepared by reacting chitosan (CTS) with chloroacetic acid and characterized by 13C-NMR spectroscopy to confirm that carboxymethylation occurred only in the amino groups. The adsorption properties of CTS, NCMC and O-carboxymethyl chitosan (OCMC) towards Pb(II) ions were evaluated and the order of the adsorption capacity was as follows: NCMC > OCMC > CTS. The effects of initial pH value (2.0–5.5) of the solutions and contact time (5–120 min) on adsorption of Pb(II) were investigated and the kinetic data were evaluated using the pseudo-first-order and pseudo-second-order models. Kinetics study showed that the adsorption process followed second-order kinetics rather than the first-order one. Furthermore, the experimental equilibrium data of Pb(II) on the NCMC were analyzed using the Langmuir and Freundlich isotherm models and the results indicated that the Langmuir model gave a better fit than the Freundlich equation and the maximum adsorption capacity obtained from the Langmuir model was 421.9 mg g−1.


Plant Disease ◽  
2021 ◽  
Author(s):  
Kholoud Alananbeh ◽  
Monther M Tahat ◽  
Haitham Al-Taweel

Date palm (Phoenix dactylifera L.) is one of the world’s oldest cultivated fruit crops. In Jordan, date palm farming started in the 1990s. The major date palm planting areas are Jordan valley, Aqaba, and Azraq (Al Antary et al., 2015). ‘Medjool’ and ‘Barhi’ are the two major cultivars in Jordan. In early 2018, some 18- to 24- month old date palm trees (cv ‘Medjool’) showed light brownish discoloration and dryness symptoms on the leaves and branches of infected date palm trees at the Jordan University Agricultural Research Station (JUARS) at the Jordan Valley (GPS coordinates 32.086871, 35.597219) (Figure 1). All the leaf parts including leaf base, spines, and leaflets were wrinkled and malformed. The infection led to a loss of 1-2% out of 1100 total Medjool trees at the station. Similar symptoms were observed in many date palm farms in the Jordan Valley. Diseased samples from rachis tissue from the JUARS were collected, surface sterilized with 5% sodium hypochlorite for five minutes, rinsed with distilled water for three times, dried, and plated on potato dextrose agar (PDA) medium (HIMEDIA). The plates were incubated at 25°C for seven days. After that, different fungal colonies were purified using the hyphal tip method. Mycelium of a representative isolate (FpDP2018JO-01) was harvested, DNA extracted using the CTAB protocol (Doyle and Doyle, 1990), amplified with three primers: ITS1/4 (White et al., 1990), β-tubulin and the elongation factor 1-alpha (EF1) gene regions. Amplicons were sequenced at Macrogen Inc, South Korea. Sequences were edited via MEGA 7 software (Kumar et al., 2016) and Blastn at the National Center for Biotechnology Information (http://www.ncbi.nlm.nih.gov) which was used to search for similar accessions. The sequences were submitted to the GenBank and accession numbers were received for ITS1/2 (MK522076), β-tubulin (MK720958) and elongation factor 1 alpha (MW533146). The sequences were further used at the Fusarium MLST (https://fusarium.mycobank.org/) for identity confirmation. ITS1/4 and β-tubulin could not discriminate the species Fusarium proliferatum but EF1 – alpha could (Figure 2a-c; Supplement 1). For morphological identification, four representative F. proliferatum isolates (FpDP2018JO-01- FpDP2018JO-04) were used. Mycelium were white to dark purple in color, macroconidia (20.5 - 44.5 × 3.3 - 7.5 μm) were thin, slender, with 3-5 septa, and microconidia (4.3 – 12.1 × 2.5 – 4.3 μm) were thin and aseptate (Figure 3). Koch’s postulate was performed on one-year-old seedlings according to Abdalla et al., 2000 method using the same sequenced isolate (FpDP2018JO-01). Five plants were inoculated by injecting 2 mlof inoculum into the crown area using a hypodermic needle and syringe. The inoculum was prepared according to Abdalla et al. (2000). The control set of seedlings (n=5) were injected with sterile distilled water. The experiment was arranged in a CRD design. Symptoms were evaluated three months after inoculation. On seedlings, yellowing of leaflets, discoloration of spines and rachis, and dryness of leaves were observed. Control seedlings showed no symptoms. Re-isolation form the detached leaves and infected seedlings was conducted to satisfy Koch’s postulates. Fusarium sp. was confirmed to be F. proliferatum based on their microscopic characteristics. To our knowledge, this is the first record of F. proliferatum on date palm in Jordan. Date palm in Jordan especially ‘Medjool’ is an important cash crop. Fusarium spp. is an important pathogen that could cause huge losses on date palm and other crops. In Jordan, the pathogen has been isolated from samples from six farms so far, but detailed studies have not been conducted. It would be of importance to survey date palm farms for fungal diseases, test their pathogenicity using several isolates, and characterize them for proper management strategies. F. proliferatum was isolated from roots and leaves of declining date palm trees from many regions of Saudi Arabia and caused symptoms similar to those of F. oxysporum f. sp. albedinis, the causal agent of Bayoud (Abdalla et al. 2000; Saleh et al. 2016). Notonly that, but F. proliferatum was found to have the highest colonization abilities on date palm leaflets and is becoming serious pathogen on date palm (Saleh et al. 2016


Sign in / Sign up

Export Citation Format

Share Document