scholarly journals An Analytic Study of the Effect of a Vane on the Hydraulic Field around a Cylinder

2021 ◽  
Vol 13 (3) ◽  
pp. 123-139
Author(s):  
Rafi M. QASIM ◽  
Tahseen Ali JABBAR
Keyword(s):  
Flow Velocity ◽  
Flow Pattern ◽  
Pressure Coefficient ◽  
Vital Role ◽  
Navier Stokes ◽  
Ansys Fluent ◽  
Turbulent Dissipation ◽  
Cylinder Diameter ◽  
Flow Velocity Profile ◽  
Hydraulic Variables

The flow pattern around the cylinder body is a very serious problem and this problem may become more serious and sensitive, when we place a vane neighboring to the cylinder. The present paper deals with the vane impact on the flow pattern around the cylinder. To investigate this problem the ANSYS fluent software is employed in order to achieve the two dimensional numerical analysis. Here, Reynolds Average Navier Stokes model is adopted. The investigation comprises the following hydraulic variables, like eddy viscosity, turbulent intensity, turbulent kinetic energy, turbulent dissipation rate, flow velocity profile, static pressure and pressure coefficient. The constant flow velocity, cylinder diameter and vane dimension are adopted in this analysis, while the different certain distance between the vane and the cylinder is considered. The used vane has a rectangular shape. In this analysis, it is clear that the vane plays a sensitive vital role in the hydraulic behavior of the flow pattern around the cylinder. The study has taken up four distances between the vane and the cylinder, these distances is a function of the cylinder diameter, in addition to the direct touch that happens between the vane and the cylinder. The analysis also shows that when the cylinder has direct touch with the vane, the dramatic reduction will occur in hydraulic variables.

scholarly journals A comparative study of URANS, DDES and DES simulations of Jetstream 31 aircraft near the compressibility limit

2021 ◽  
Vol 16 (2) ◽  
pp. 159-172
Author(s):  
Hrishabh Chaudhary ◽  
Nicolas Ledos ◽  
László Könözsy
Keyword(s):  
Comparative Study ◽  
Turbulence Modeling ◽  
Pressure Coefficient ◽  
Turbulence Models ◽  
Flight Test ◽  
Scale Model ◽  
Navier Stokes ◽  
Ansys Fluent ◽  
Fluent Software ◽  
Lift And Drag

This work presents a comparative study of Unsteady Reynolds–Averaged Navier–Stokes (URANS), Detached Eddy Simulations (DES) and Delayed Detached Eddy Simulations (DDES) turbulence modeling approaches by performing numerical investigation with the ANSYS-FLUENT software package on a full-scale model of the Jetstream 31 aircraft. The lift and drag coefficients obtained from different models are compared with flight test data, wind tunnel data and theoretical estimates. The different turbulence models are also compared with each other on the basis of pressure coefficient distributions and velocity fluctuations along various lines and sections of the aircraft. For the mesh and the conditions presented in this study, the DDES Spalart–Allmaras model gives the best overall results.

Investigation of the influence of the flow structure on the accuracy of flow measurement before a hydrometric structure in an open channel

2020 ◽  
pp. 41-44
Author(s):  
Anatoly Kusher
Keyword(s):  
Velocity Profile ◽  
Flow Velocity ◽  
Water Flow ◽  
Flow Measurement ◽  
Water Discharge ◽  
Critical Depth ◽  
Flow Measurements ◽  
Study Results ◽  
Flow Velocity Profile ◽  
Upstream Flow

The reliability of water flow measurement in irrigational canals depends on the measurement method and design features of the flow-measuring structure and the upstream flow velocity profile. The flow velocity profile is a function of the channel geometry and wall roughness. The article presents the study results of the influence of the upstream flow velocity profile on the discharge measurement accuracy. For this, the physical and numerical modeling of two structures was carried out: a critical depth flume and a hydrometric overfall in a rectangular channel. According to the data of numerical simulation of the critical depth flume with a uniform and parabolic (1/7) velocity profile in the upstream channel, the values of water discharge differ very little from the experimental values in the laboratory model with a similar geometry (δ < 2 %). In contrast to the critical depth flume, a change in the velocity profile only due to an increase in the height of the bottom roughness by 3 mm causes a decrease of the overfall discharge coefficient by 4…5 %. According to the results of the numerical and physical modeling, it was found that an increase of backwater by hydrometric structure reduces the influence of the upstream flow velocity profile and increases the reliability of water flow measurements.

Experimental and Numerical Analysis of a Motorcycle Air Intake System Aerodynamics and Performance

2020 ◽  
Vol 17 (1) ◽  
Author(s):  
M. A. Abd Halim ◽  
N. A. R. Nik Mohd ◽  
M. N. Mohd Nasir ◽  
M. N. Dahalan
Keyword(s):  
Combustion Process ◽  
Three Dimensional ◽  
Engine Performance ◽  
Internal Flow ◽  
Rapid Expansion ◽  
Navier Stokes ◽  
Turbulent Fluctuation ◽  
Ansys Fluent ◽  
Induction System ◽  
Acceleration And Deceleration

Induction system or also known as the breathing system is a sub-component of the internal combustion system that supplies clean air for the combustion process. A good design of the induction system would be able to supply the air with adequate pressure, temperature and density for the combustion process to optimizing the engine performance. The induction system has an internal flow problem with a geometry that has rapid expansion or diverging and converging sections that may lead to sudden acceleration and deceleration of flow, flow separation and cause excessive turbulent fluctuation in the system. The aerodynamic performance of these induction systems influences the pressure drop effect and thus the engine performance. Therefore, in this work, the aerodynamics of motorcycle induction systems is to be investigated for a range of Cubic Feet per Minute (CFM). A three-dimensional simulation of the flow inside a generic 4-stroke motorcycle airbox were done using Reynolds-Averaged Navier Stokes (RANS) Computational Fluid Dynamics (CFD) solver in ANSYS Fluent version 11. The simulation results are validated by an experimental study performed using a flow bench. The study shows that the difference of the validation is 1.54% in average at the total pressure outlet. A potential improvement to the system have been observed and can be done to suit motorsports applications.

The inlet flow structure of a conceptual open-nose supersonic drone

2021 ◽  
pp. 095441002098304
Author(s):  
Eiman B Saheby ◽  
Xing Shen ◽  
Anthony P Hays ◽  
Zhang Jun
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Computational Fluid Dynamic Simulation ◽  
Navier Stokes ◽  
Ansys Fluent ◽  
Navier Stokes Equations ◽  
Aerodynamic Efficiency ◽  
Performance Effects

This study describes the aerodynamic efficiency of a forebody–inlet configuration and computational investigation of a drone system, capable of sustainable supersonic cruising at Mach 1.60. Because the whole drone configuration is formed around the induction system and the design is highly interrelated to the flow structure of forebody and inlet efficiency, analysis of this section and understanding its flow pattern is necessary before any progress in design phases. The compression surface is designed analytically using oblique shock patterns, which results in a low drag forebody. To study the concept, two inlet–forebody geometries are considered for Computational Fluid Dynamic simulation using ANSYS Fluent code. The supersonic and subsonic performance, effects of angle of attack, sideslip, and duct geometries on the propulsive efficiency of the concept are studied by solving the three-dimensional Navier–Stokes equations in structured cell domains. Comparing the results with the available data from other sources indicates that the aerodynamic efficiency of the concept is acceptable at supersonic and transonic regimes.

Numerical study of the aerodynamic and power characteristics of the cycloidal rotor, under incoming flow

2019 ◽  
pp. 25-34
Author(s):  
Александр Анатольевич Дектерев ◽  
Артем Александрович Дектерев ◽  
Юрий Николаевич Горюнов
Keyword(s):  
Flow Velocity ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Incoming Flow ◽  
Ansys Fluent ◽  
Energy Characteristics ◽  
Power Characteristics ◽  
Calculation Results

Исследование направлено на разработку и апробацию методики численного моделирования аэродинамических и энергетических характеристик циклоидального ротора. За основу взята конфигурация ротора IAT21 L3. Для нее с использованием CFD-пакета ANSYS Fluent построена математическая модель и выполнен расчет. Проанализировано влияние скорости набегающего потока воздуха на движущийся ротор. Математическая модель и полученные результаты исследования могут быть использованы при создании летательных аппаратов с движителями роторного типа. This article addresses the study of the aerodynamic and energy characteristics of a cycloidal rotor subject to the influence of the incoming flow. Cycloidal rotor is one of the perspective devices that provide movement of aircrafts. Despite the fact that the concept of a cycloidal rotor arose in the early twentieth century, the model of a full-scale aircraft has not been yet realized. Foreign scientists have developed models of aircraft ranging in weight from 0.06 to 100 kg. The method of numerical calculation of the cycloidal rotor from the article [1] is considered and realized in this study. The purpose of study was the development and testing of a numerical simulation method for the cycloidal rotor and study aerodynamic and energy characteristics of the rotor in the hovering mode and under the influence of the oncoming flow. The aerodynamic and energy characteristics of the cycloidal rotor, rotating at a speed of 1000 rpm with incoming flow on it with velocities of 20-80 km/h, were calculated. The calculation results showed a directly proportional increase of thrust with an increase of the incoming on the rotor flow velocity, but the power consumed by the rotor was also increased. Increase of the incoming flow velocity leads to the proportional increasing of the lift coefficient and the coefficient of drag. Up to a speed of 80 km/h, an increase in thrust and power is observed; at higher speeds, there is a predominance of nonstationary effects and difficulties in estimating the aerodynamic characteristics of the rotor. In the future, it is planned to consider the 3D formulation of the problem combined with possibility of the flow coming from other sides.

Numerical Study on Control of Sunroof Buffeting

2021 ◽  
Vol 13 (2) ◽  
Author(s):  
K. Vijaykumar ◽  
S. Poonkodi ◽  
A.T. Sriram
Keyword(s):  
Numerical Study ◽  
Leading Edge ◽  
Dominant Frequency ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Ansys Fluent ◽  
Flow Modification ◽  
Numerical Result ◽  
Modification Technique ◽  
Commercial Solver

Sunroof has become one of the essential features of a luxury car, and it provides natural air circulation and good illumination into the car. But the primary problem associated with it is the buffeting noise which causes discomfort to the passengers. Though adequate studies were carried out on sunroof buffeting, efficient control techniques are needed to be developed from fundamental mechanism. To reduce the buffeting noise, flow modifications at the entrance of the sunroof is considered in this study. The internal portion of the car with sunroof is simplified into a shear driven open cavity, and two-dimensional numerical simulations are carried out using commercial solver, ANSYS Fluent. Reynolds averaged Navier-Stokes equation is used with the realizable k-? turbulence model. The unsteady numerical result obtained in this study is validated with the available experimental results for the dominant frequency. The prediction is good agreement with experiment. Flow modification technique is proposed to control the sunroof buffeting by implementing geometric modifications. A hump has been placed near the leading edge of the cavity which resulted in significant reduction of pressure oscillations. Parametric studies have been performed by varying the height of hump and the distance of hump from the leading edge. There is no prominent difference when the height of the hump is varied. As the distance of the hump from the leading edge is reduced, the sound pressure level decreases.

Conjugate Free Convection Heat Transfer and Thermodynamic Analysis of Infrared Suppression Device with Cylindrical Funnels

2022 ◽  
Author(s):  
Vikrant Chandrakar ◽  
Arnab Mukherjee ◽  
Jnana Ranjan Senapati ◽  
Ashok Kumar Barik
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Convection Heat Transfer ◽  
Navier Stokes ◽  
Bejan Number ◽  
Navier Stokes Equation ◽  
Ansys Fluent ◽  
Geometric Ratio ◽  
Flow Rate Increase ◽  
Free Convection Heat

Abstract A convection system can be designed as an energy-efficient one by making a considerable reduction in exergy losses. In this context, entropy generation analysis is performed on the infrared suppression system numerically. In addition, results due to heat transfer are also shown. The numerical solution of the Navier-stokes equation, energy equation, and turbulence equation is executed using ANSYS Fluent 15.0. To perform the numerical analysis, different parameters such as the number of funnels, Rayleigh number (Ra), inner surface temperature, and geometric ratio are varied in the practical range. Results are shown in terms of heat transfer, entropy generation, irreversibility (due to heat transfer and fluid friction), and Bejan number with some relevant parameters. Streamlines and temperature contours are also provided for better visualization of temperature and flow field around the device. Results show that heat transfer and mass flow rate increase with the increase in Ra. Entropy generation and the irreversibility rise with an increase in the number of funnels and geometric ratio. Also, the Bejan number decreases with an increase in Ra and the number of funnels. A cooling time is also obtained using the lumped capacitance method.

scholarly journals Propulsion Performance of the Full-Active Flapping Foil in Time-Varying Freestream

2020 ◽  
Vol 10 (18) ◽  
pp. 6226
Author(s):  
Zhanfeng Qi ◽  
Lishuang Jia ◽  
Yufeng Qin ◽  
Jian Shi ◽  
Jingsheng Zhai
Keyword(s):  
Flow Velocity ◽  
Steady Flow ◽  
Navier Stokes ◽  
Time Varying ◽  
Flapping Foil ◽  
Propulsion Performance ◽  
Reduced Frequency ◽  
Motion Parameters ◽  
Volume Method ◽  
The Impact

A numerical investigation of the propulsion performance and hydrodynamic characters of the full-active flapping foil under time-varying freestream is conducted. The finite volume method is used to calculate the unsteady Reynolds averaged Navier–Stokes by commercial Computational Fluid Dynamics (CFD) software Fluent. A mesh of two-dimensional (2D) NACA0012 foil with the Reynolds number Re = 42,000 is used in all simulations. We first investigate the propulsion performance of the flapping foil in the parameter space of reduced frequency and pitching amplitude at a uniform flow velocity. We define the time-varying freestream as a superposition of steady flow and sinusoidal pulsating flow. Then, we study the influence of time-varying flow velocity on the propulsion performance of flapping foil and note that the influence of the time-varying flow is time dependent. For one period, we find that the oscillating amplitude and the oscillating frequency coefficient of the time-varying flow have a significant influence on the propulsion performance of the flapping foil. The influence of the time-varying flow is related to the motion parameters (reduced frequency and pitching amplitude) of the flapping foil. The larger the motion parameters, the more significant the impact of propulsion performance of the flapping foil. For multiple periods, we note that the time-varying freestream has little effect on the propulsion performance of the full-active flapping foil at different pitching amplitudes and reduced frequency. In summary, we conclude that the time-varying incoming flow has little effect on the flapping propulsion performance for multiple periods. We can simplify the time-varying flow to a steady flow field to a certain extent for numerical simulation.

Arriving at the Optimum Overlap Ratio for an Elliptical-Bladed Savonius Rotor

2017 ◽  
Author(s):  
Nur Alom ◽  
Ujjwal K. Saha
Keyword(s):  
Numerical Study ◽  
Superior Performance ◽  
Navier Stokes ◽  
Speed Ratio ◽  
Small Scale ◽  
Efficient Manner ◽  
Ansys Fluent ◽  
Savonius Rotor ◽  
Velocity Magnitude ◽  
Overlap Ratio

The Savonius rotor appears to be particularly promising for the small-scale applications because of its design simplicity, good starting ability, and insensitivity to wind directions. There has been a growing interest in recent times to harness wind energy in an efficient manner by developing newer blade profiles of Savonius rotor. The overlap ratio (OR), one of the important geometric parameters, plays a crucial role in the turbine performance. In a recent study, an elliptical blade profile with a sectional cut angle (θ) of 47.5° has demonstrated its superior performance when set at an OR = 0.20. However, this value of OR is ideal for a semicircular profile, and therefore, requires further investigation to arrive at the optimum overlap ratio for the elliptical profile. In view of this, the present study attempts to make a systemic numerical study to arrive at the optimum OR of the elliptical profile having sectional cut angle, θ = 47.5°. The 2D unsteady simulation is carried out around the elliptical profile considering various overlap ratios in the range of 0.0 to 0.30. The continuity, unsteady Reynolds Averaged Navier-Stokes (URANS) equations and two equation eddy viscosity SST (Shear Stress transport) k-ω model are solved by using the commercial finite volume method (FVM) based solver ANSYS Fluent. The torque and power coefficients are calculated as a function of tip speed ratio (TSR) and at rotating conditions. The total pressure, velocity magnitude and turbulence intensity contours are obtained and analyzed to arrive at the intended objective. The numerical simulation demonstrates an improved performance of the elliptical profile at an OR = 0.15.

Sign in / Sign up

Export Citation Format

Share Document