scholarly journals Numerical analysis of RC columns under cyclic uniaxial and biaxial lateral load

2021 ◽  
Vol 73 (10) ◽  
pp. 979-994
Keyword(s):  
Numerical Analysis ◽  
Lateral Displacement ◽  
Reinforcement Ratio ◽  
Shear Load ◽  
Longitudinal Reinforcement ◽  
Initial Stiffness ◽  
Structural Behaviour ◽  
Cross Sectional ◽  
Rc Columns ◽  
Cyclic Shear

A numerical finite element study is conducted in this paper to examine structural behaviour of high strength RC columns exposed to biaxial and uniaxial lateral displacement histories with constant axial load. The numerical analysis of 24 models was made using ABAQUS / CAE. The comparison between numerical analysis and experimental results shows good agreement through validations. The considered parametric study involves determination of the longitudinal reinforcement ratio, total cross-sectional area of confinement steel (Ash), and uniaxial and biaxial cyclic shear load. Numerical analysis results show that an increase of longitudinal reinforcement for a uniaxial and biaxial lateral historic load will significantly increase maximum and ultimate load of columns, corresponding deflections, number of cycles at maximum and ultimate loads, and initial stiffness Ki, while the effect of transverse reinforcement is less pronounced. The columns load and deformation capacity decreases significantly with application of biaxial cyclic shear load, compared with uniaxial load. Also, this effect reduces with an increase in longitudinal reinforcement ratio (%ρl) and Ash.

scholarly journals Flexural Behavior of the Innovative CA-UHPC Slabs with High and Low Reinforcement Ratios

2019 ◽  
Vol 2019 ◽  
pp. 1-14 ◽  
Author(s):  
Yu Feng ◽  
Jianan Qi ◽  
Jingquan Wang ◽  
Jiaping Liu ◽  
Jianzhong Liu
Keyword(s):  
Ductile Failure ◽  
Aggregate Size ◽  
Load Resistance ◽  
Reinforcement Ratio ◽  
Flexural Behavior ◽  
Maximum Aggregate Size ◽  
Longitudinal Reinforcement ◽  
Test Results ◽  
Initial Stiffness ◽  
Large Expansion

This paper presents an experimental study on the flexural behavior of an innovative CA-UHPC (ultrahigh-performance concrete containing coarse aggregate) slab with high and low reinforcement ratios. A total of eighteen CA-UHPC slabs were tested to failure under the parameters of longitudinal reinforcement ratio, curing method, and maximum aggregate size. Test results indicated that sufficient longitudinal reinforcement should be embedded to prevent the brittle failure and disastrous damage. High ductile failure mode was observed for specimens with high reinforcement ratio compared with specimens with low reinforcement ratio. Instead of extensively crushing as normal strength concrete, delamination failure appeared in the compression zone of the CA-UHPC slabs owing to the fibers’ bridging effect, the yielding of longitudinal reinforcement, and the large expansion of flexural cracks which led to the final failure. The reinforced CA-UHPC slabs demonstrated excellent deformability, and ultimate ratio of deflection to span increased from 1/281 to 1/12 when the reinforcement ratio raised from 0% to 3.45%. Stiffness of the reinforced specimens at the flexural cracking state was about 88% and only approximately 6% at the ultimate state, but nearly 50% of the initial stiffness remained when the longitudinal reinforcements yielded, which indicated superior load resistance ability and excellent postcracking deformability. A new ductility index was proposed to evaluate the postcracking ductility of the CA-UHPC specimens. Finally, test results were compared with the flexural strength predictions of CECS 38-2004, ACI 544.4R, and BS EN 1992.

scholarly journals Investigation on the Influence of Type of Steel Fibers on Shear Failure of HPFRCC Beams

2018 ◽  
Vol 203 ◽  
pp. 06018
Author(s):  
Ehsan Nikbakht ◽  
Hugo Aureliano da Costa Gaspar ◽  
Rakan Mousa Jaradah ◽  
Muslich Hartadi Sutanto
Keyword(s):  
High Performance ◽  
Shear Failure ◽  
Steel Fiber ◽  
Load Capacity ◽  
Reinforcement Ratio ◽  
Beam Specimen ◽  
Shear Load ◽  
Longitudinal Reinforcement ◽  
Ultimate Load Capacity ◽  
High Performance Fiber

This paper investigates the influence of different types of steel fiber on the mechanical properties of High Performance Fiber Reinforced Cementitious Composite (HPFRCC) as well as the shear failure mode of steel reinforced HPFRCC beams. Moreover, the influence of parameters such as span to effective depths (a/d) ratio of beams and longitudinal reinforcement ratio on shear strength of HPFRCC beams are examined. In reference to the results, despite the same tensile strength of both straight and hooked fibers utilized, the performance of straight steel fiber is superior to the hooked steel fiber due to its physiognomies. However, the beam specimens with straight steel fiber exhibit considerably lower deflection and ultimate load capacity when subjected to shear load. Also, the results show that the influence of type of steel fiber is more significant than the influence of longitudinal reinforcement ratio, i.e. the beam specimen with hooked steel fiber and 0.94% reinforcement ratio displayed higher deflection and ultimate shear load capacity compared to the specimen with straight steel fiber and 1.88% longitudinal reinforcement ratio.

Parametric study of multi-story, perforated, partially grouted masonry walls subjected to in-plane cyclic actions

2020 ◽  
Author(s):  
Klaus Medeiros ◽  
Kyle Chavez ◽  
Fernando S. Fonseca ◽  
Guilherme Parsekian ◽  
Nigel G. Shrive
Keyword(s):  
Experimental Data ◽  
Shear Strength ◽  
Aspect Ratio ◽  
Load Capacity ◽  
Axial Stress ◽  
Reinforcement Ratio ◽  
Masonry Walls ◽  
Finite Element Models ◽  
Initial Stiffness ◽  
Vertical Reinforcement

Finite element models were developed to assess the influence of several parameters on the load capacity, deflection, and initial stiffness of multi-story, partially grouted masonry walls with openings. The base model was validated with experimental data from three walls. The analyses indicated that the load capacity of masonry walls was considerably sensitive to the ungrouted and grouted masonry strengths and mortar shear strength; moderately sensitive to the vertical reinforcement ratio and aspect ratio; slightly sensitive to the axial stress; and almost insensitive to the opening size, reinforcement spacing, and horizontal reinforcement ratio. The deflection of the walls had well-defined correlations with the masonry strength, vertical reinforcement, axial stress and aspect ratio. The initial stiffness was especially sensitive to the axial stress and the aspect ratio, but weakly correlated with the opening size, and the spacing and size of the reinforcement.

Numerical analysis of the shear strength of circular reinforced concrete columns subjected to cyclic lateral loads using linear genetic programming

2020 ◽  
Vol 37 (7) ◽  
pp. 2517-2537
Author(s):  
Mostafa Rezvani Sharif ◽  
Seyed Mohammad Reza Sadri Tabaei Zavareh
Keyword(s):  
Numerical Modeling ◽  
Shear Strength ◽  
Reinforced Concrete ◽  
Numerical Analysis ◽  
Genetic Programming ◽  
Linear Genetic Programming ◽  
Rc Columns ◽  
Content Type ◽  
Alternative Approach ◽  
Engineering Problems

Purpose The shear strength of reinforced concrete (RC) columns under cyclic lateral loading is a crucial concern, particularly, in the seismic design of RC structures. Considering the costly procedure of testing methods for measuring the real value of the shear strength factor and the existence of several parameters impacting the system behavior, numerical modeling techniques have been very much appreciated by engineers and researchers. This study aims to propose a new model for estimation of the shear strength of cyclically loaded circular RC columns through a robust computational intelligence approach, namely, linear genetic programming (LGP). Design/methodology/approach LGP is a data-driven self-adaptive algorithm recently used for classification, pattern recognition and numerical modeling of engineering problems. A reliable database consisting of 64 experimental data is collected for the development of shear strength LGP models here. The obtained models are evaluated from both engineering and accuracy perspectives by means of several indicators and supplementary studies and the optimal model is presented for further purposes. Additionally, the capability of LGP is examined to be used as an alternative approach for the numerical analysis of engineering problems. Findings A new predictive model is proposed for the estimation of the shear strength of cyclically loaded circular RC columns using the LGP approach. To demonstrate the capability of the proposed model, the analysis results are compared to those obtained by some well-known models recommended in the existing literature. The results confirm the potential of the LGP approach for numerical analysis of engineering problems in addition to the fact that the obtained LGP model outperforms existing models in estimation and predictability. Originality/value This paper mainly represents the capability of the LGP approach as a robust alternative approach among existing analytical and numerical methods for modeling and analysis of relevant engineering approximation and estimation problems. The authors are confident that the shear strength model proposed can be used for design and pre-design aims. The authors also declare that they have no conflict of interest.

scholarly journals A case study of university student networks and the COVID-19 pandemic using a social network analysis approach in halls of residence

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
José Alberto Benítez-Andrades ◽  
Tania Fernández-Villa ◽  
Carmen Benavides ◽  
Andrea Gayubo-Serrenes ◽  
Vicente Martín ◽  
...  
Keyword(s):  
Social Network ◽  
Social Network Analysis ◽  
Network Analysis ◽  
University Students ◽  
Methodological Approach ◽  
Centrality Measures ◽  
Structural Behaviour ◽  
Cross Sectional ◽  
Depth Analysis ◽  
The University

AbstractThe COVID-19 pandemic has meant that young university students have had to adapt their learning and have a reduced relational context. Adversity contexts build models of human behaviour based on relationships. However, there is a lack of studies that analyse the behaviour of university students based on their social structure in the context of a pandemic. This information could be useful in making decisions on how to plan collective responses to adversities. The Social Network Analysis (SNA) method has been chosen to address this structural perspective. The aim of our research is to describe the structural behaviour of students in university residences during the COVID-19 pandemic with a more in-depth analysis of student leaders. A descriptive cross-sectional study was carried out at one Spanish Public University, León, from 23th October 2020 to 20th November 2020. The participation was of 93 students, from four halls of residence. The data were collected from a database created specifically at the university to "track" contacts in the COVID-19 pandemic, SiVeUle. We applied the SNA for the analysis of the data. The leadership on the university residence was measured using centrality measures. The top leaders were analyzed using the Egonetwork and an assessment of the key players. Students with higher social reputations experience higher levels of pandemic contagion in relation to COVID-19 infection. The results were statistically significant between the centrality in the network and the results of the COVID-19 infection. The most leading students showed a high degree of Betweenness, and three students had the key player structure in the network. Networking behaviour of university students in halls of residence could be related to contagion in the COVID-19 pandemic. This could be described on the basis of aspects of similarities between students, and even leaders connecting the cohabitation sub-networks. In this context, Social Network Analysis could be considered as a methodological approach for future network studies in health emergency contexts.

Experimental study on the axial compression performance of GFRP-reinforced concrete square columns

2018 ◽  
Vol 22 (7) ◽  
pp. 1554-1565 ◽  
Author(s):  
Jianwei Tu ◽  
Kui Gao ◽  
Lang He ◽  
Xinping Li
Keyword(s):  
Carrying Capacity ◽  
Ultimate Load ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Longitudinal Reinforcement ◽  
Rc Columns ◽  
Compression Performance ◽  
Reinforced Polymer ◽  
Load Carrying ◽  
Ultimate Load Carrying Capacity

At present, extensive studies have been conducted relative to the topic of fiber-reinforced polymer(FRP)- reinforced concrete (RC) flexural members, and many design methods have also been introduced. There have, however, been few studies conducted on the topic of FRP-RC compression members. In light of this, eight glass-fiber-reinforced polymer (GFRP)-RC square columns (200×200×600 mm) were tested in order to investigate their axial compression performance. These columns were reinforced with GFRP longitudinal reinforcement and confined GFRP stirrup. These experiments investigated the effects of the longitudinal reinforcement ratio, stirrup configuration (spirals versus hoops) and spacing on the load-carrying capacity and failure modes of GFRP-RC rectangular columns. The test results indicate that the load-carrying capacity of longitudinal GFRP bars accounted for 3%-7% of the ultimate load-carrying capacity of the columns. The ultimate load-carrying capacity of RC columns confined with GFRP spirals increased by 0.8%-1.6% with higher ductility, compared to GFRP hoops. Reducing the stirrup spacing may prevent the buckling failure of the longitudinal bars and increase the ductility and load-carrying capacity of the GFRP-RC columns. It has been found that setting the GFRP compressive strength to 35% of the GFRP maximum tensile strength yields a reasonable estimate of ultimate load-carrying capacity of GFRP-RC columns.

scholarly journals Experimental analysis of steel fiber reinforced concrete beams in shear

2022 ◽  
Vol 15 (3) ◽  
Author(s):  
Aaron Kadima Lukanu Lwa Nzambi ◽  
Dênio Ramam Carvalho de Oliveira ◽  
Marcus Vinicius dos Santos Monteiro ◽  
Luiz Felipe Albuquerque da Silva
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Experimental Program ◽  
Longitudinal Reinforcement ◽  
Fiber Addition

Abstract Some normative recommendations are conservative in relation to the shear strength of reinforced concrete beams, not directly considering the longitudinal reinforcement rate. An experimental program containing 8 beams of (100 x 250) mm2 and a length of 1,200 mm was carried out. The concrete compression strength was 20 MPa with and without 1.00% of steel fiber addition, without stirrups and varying the longitudinal reinforcement ratio. Comparisons between experimental failure loads and main design codes estimates were assessed. The results showed that the increase of the longitudinal reinforcement ratio from 0.87% to 2.14% in beams without steel fiber led to an improvement of 59% in shear strength caused by the dowel effect, while the corresponding improvement was of only 22% in fibered concrete beams. A maximum gain of 109% in shear strength was observed with the addition of 1% of steel fibers comparing beams with the same longitudinal reinforcement ratio (1.2%). A significant amount of shear strength was provided by the inclusion of the steel fibers and allowed controlling the propagation of cracks by the effect of stress transfer bridges, transforming the brittle shear mechanism into a ductile flexural one. From this, it is clear the shear benefit of the steel fiber addition when associated to the longitudinal reinforcement and optimal values for this relationship would improve results.

scholarly journals Lateral shear strength of rectangular RC columns subjected to combined P-V-M monotonic loading

2020 ◽  
Vol 53 (4) ◽  
pp. 227-241
Author(s):  
Aysha M Zaneeb ◽  
Rupen Goswami ◽  
C V R Murty
Keyword(s):  
Shear Strength ◽  
Test Data ◽  
Rectangular Cross Section ◽  
Resistance Mechanism ◽  
Bending Moment ◽  
Shear Resistance ◽  
Shear Capacity ◽  
Longitudinal Reinforcement ◽  
Lateral Shear ◽  
Rc Columns

An analytical method is presented to estimate lateral shear strength (and identify likely mode and location of failure) in reinforced concrete (RC) cantilever columns of rectangular cross-section under combined axial force, shear force and bending moment. Change in shear capacity of concrete with flexural demand at a section is captured explicitly and the shear resistance offered by concrete estimated; this is combined with shear resistance offered by transverse and longitudinal reinforcement bars to estimate the overall shear capacity of RC columns. Shear–moment (V-M) interaction capacity diagram of an RC column, viewed alongside the demand diagram, identifies the lateral shear strength and failure mode. These analytical estimates compare well with test data of 107 RC columns published in literature; the test data corresponds to different axial loads, transverse reinforcement ratios, longitudinal reinforcement ratios, shear span to depth ratios, and loading conditions. Also, the analytical estimates are compared with those obtained using other analytical methods reported in literature; in all cases, the proposed method gives reasonable accuracy when estimating shear capacity of RC columns.  In addition, the method provides insights into the shear resistance mechanism in RC columns under the combined action of P-V-M, and it is simple to use.

Sign in / Sign up

Export Citation Format

Share Document