scholarly journals Pineapple leaf fibers as a reinforcement of biocomposites - an overview

Polimery ◽  
2021 ◽  
Vol 66 (11-12) ◽  
Author(s):  
Rahmah Mohamed ◽  
Norsuriati Muhmad Hapizi ◽  
Mohd Nurazzi Norizan ◽  
Nur Khairunnisa
Keyword(s):  
Mechanical Properties ◽  
Literature Review ◽  
Fiber Length ◽  
Filler Content ◽  
Natural Fibers ◽  
Polymer Fiber ◽  
Factors Influencing ◽  
Potential Applications

Based on 87 references, a literature review was presented on PLA reinforced with pineapple leaf fibers (PALF). The properties of PALF were compared with those of other natural fibers. Mechanical properties of PLA composites and factors influencing them, such as filler content, adhesion at the interface between polymer fiber and matrix, as well as fiber length and their modification were discussed. Potential applications of PLA/PALF composites were also presented.

Experimental study on effect of fiber length and fiber content on tensile and flexural properties of bamboo fiber/epoxy composite

2019 ◽  
Vol 15 (5) ◽  
pp. 947-957 ◽  
Author(s):  
Giridharan R. ◽  
Raatan V.S. ◽  
Jenarthanan M.P.
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Epoxy Composite ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Fiber Content ◽  
Bamboo Fiber ◽  
Flexural Properties ◽  
Fiber Reinforced ◽  
Content Type

Purpose The purpose of this paper is to study the effects of fiber length and content on properties of E-glass and bamboo fiber reinforced epoxy resin matrices. Experiments are carried out as per ASTM standards to find the mechanical properties. Further, fractured surface of the specimen is subjected to morphological study. Design/methodology/approach Composite samples were prepared according to ASTM standards and were subjected to tensile and flexural loads. The fractured surfaces of the specimens were examined directly under scanning electron microscope. Findings From the experiment, it was found that the main factors that influence the properties of composite are fiber length and content. The optimum fiber length and weight ratio are 15 mm and 16 percent, respectively, for bamboo fiber/epoxy composite. Hence, the prediction of optimum fiber length and content becomes important, so that composite can be prepared with best mechanical properties. The investigation revealed the suitability of bamboo fiber as an effective reinforcement in epoxy matrix. Practical implications As bamboo fibers are biodegradable, recyclable, light weight and so on, their applications are numerous. They are widely used in automotive components, aerospace parts, sporting goods and building industry. With this scenario, the obtained result of bamboo fiber reinforced composites is not ignorable and could be of potential use, since it leads to harnessing of available natural fibers and their composites rather than synthetic fibers. Originality/value This work enlists the effect of fiber length and fiber content on tensile and flexural properties of bamboo fiber/epoxy composite, which has not been attempted so far.

Preparing of SMC Artificial Marble and its Mechanical Properties

2011 ◽  
Vol 55-57 ◽  
pp. 447-450 ◽  
Author(s):  
Jian Li ◽  
Zheng Qun Huang ◽  
Yan Qin
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fiber Length ◽  
Filler Content ◽  
Fiber Content ◽  
Molding Temperature ◽  
Overall Performance ◽  
The Impact

In this article, a kind of SMC artificial marble was prepared. In order to enhance the mechanical properties and prolong the using life of SMC artificial marble, some effects such as fiber content, filler content and molding temperature etc. on the mechanical properties were carefully studied, too. Results showed that the increase of fiber content could improve the impact strength of SMC artificial marble when the fiber length was 10mm and the increase of filler content would decrease the flexural strength of SMC artificial marble. And the molding temperature at the range of 130°C ~ 160°C had little influence on the mechanical properties of SMC artificial marble. Comparing with natural marble and casting marble, SMC artificial marble owed superior overall performance and it was much more suitable for industry production.

scholarly journals Mechanical Behavior of Coir Fiber Reinforced Epoxy Composites with Variable Fiber Lengths

2019 ◽  
Vol 8 (10) ◽  
pp. 3006-3011
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Mechanical Characteristics ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Industrial Applications ◽  
Coir Fiber ◽  
Reinforced Composites ◽  
Element Analysis ◽  
Fiber Treatment

Most studies on the application of natural fibers as reinforcement in polymer composites are growing as a result of the changes in characteristics that fibers can provide for the product. This can be achieved by manufacturing of composites using Hand Layup process. The 2% NaOH fiber treatment was performed to improve fiber-matrix interfaces making spathefibre-reinforced composites better mechanical characteristics. Filler loadings as 5% by volume of coir fiber are selected as reinforcement in composites. The varying lengths of fiber chosen as 5mm, 10mm & 15mm and resin-hardner ratio are maintained as 10:0.8. A total 3 numbers of plates with volume as 300 х 300 х 4 mm3 were produced and specimens as per the various ASTM standard were tested to determine the ultimate various Mechanical properties for different configuration. The strength of epoxy resin / coir fiber composites was noticed at a maximum 15 mm (15.27 N / mm2 ) fiber length. The maximum impact strength of the charpy was also 15 mm fiber length (9.87 kJ / m2 ).The Experimental results were validated using a numerical method technique in FEA software. The obtained results by experimentation and Finite Element Analysis are very much closer to each other. The results show good mechanical properties and hint us as a replacement for conventional materials in industrial applications.

scholarly journals Mechanical Behavior of Natural Fiber Composite Material

2021 ◽  
Author(s):  
Vikas Ghanwat ◽  
Jivan Mule ◽  
Saurabh Telore ◽  
Vijay Bhosale ◽  
Sudarshan Patale
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Composite Laminates ◽  
Fiber Length ◽  
Strain Energy ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Natural Fibers ◽  
Industrial Applications ◽  
Coir Fiber

The use of natural fibers as reinforcement in polymeric composites is increasing thanks to the improvements in properties that fibers can provide to the merchandise. Composites materials were prepared by compression molding technique with hand layup process. Treatment of fiber with 2% NaOH was carried out in order to improve the interfacial bonds between fiber and matrix leading to better mechanical properties of the spathe-fiber-reinforced composite laminates. Filler loading as 5% by volume of coir fiber or epoxy resin composites have been formulated. The fiber length was chosen as 5mm, 10mm & 15mm and the ratio of epoxy resin: hardener was maintained as 10:0.8. A total three plates with dimension as 300 mm х 300 mm х 4 mm were produced and specimens as per the varied ASTM standard were tested to determine the ultimate tensile strength, strain energy, flexural strength, strain energy and micro hardness value for different configuration. It was observed that the lastingness of epoxy resin/ coir fiber composites was maximum at 15mm fiber length (16.27 N/mm2). The charpy notch impact strength was also maximum at 15mm fiber length (10.87 kJ/m2). The results show good mechanical properties and hint us as a replacement for conventional materials in industrial applications.

Grey relational optimization for factors influencing tensile, flexural, and impact properties of hybrid sisal banana fiber epoxy composites

2020 ◽  
pp. 152808372092850
Author(s):  
KR Sumesh ◽  
K Kanthavel
Keyword(s):  
Mechanical Properties ◽  
Mechanical Stability ◽  
Signal To Noise Ratio ◽  
Matrix Material ◽  
Natural Fibers ◽  
Taguchi Optimization ◽  
Banana Fiber ◽  
Factors Influencing ◽  
The Matrix ◽  
Grey Relational

This research investigates factors contributing mechanical stability of epoxy based composites using Taguchi optimization based grey relational approach. Natural fibers of sisal, banana reinforcement along with epoxy was used as the matrix material for this compression molding technique. The grey relational results observed 7th and 14th trials were having first and second position in mechanical properties: 10% sisal, 15% banana, 8% NaOH, 10 MPa pressure, and 100°C temperature composites; 20% sisal, 10% banana, 5% NaOH, 10 MPa pressure, and 120°C temperature were the combinations. The signal to noise ratio showed the optimized data as 20% sisal, 15% banana, 5% NaOH, 10 MPa pressure, and 100°C temperature. The relation between experimental and predicted grey relational grade using artificial neural network showed good correlation stating the network topology of 5-5-1 with good predictability for analyzing factors influencing mechanical properties. SEM analysis observed pullouts of fiber, breakage in the matrix, and these two causing voids in the single reinforcement substitution using sisal and banana. Hybridization using both the fiber reduces the surface abnormalities and adds to the properties.

Mechanical properties and fracture behaviour of agave fibers bio-based epoxy laminates reinforced with zinc oxide

2020 ◽  
pp. 152808372096568
Author(s):  
Mauricio Torres ◽  
Victoria Renteria Rodriguez ◽  
Perla Itzel Alcantara ◽  
Edgar Franco-Urquiza
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Fracture Behavior ◽  
Filler Content ◽  
Fracture Behaviour ◽  
Natural Fibers ◽  
Mode I ◽  
Resin Infusion ◽  
Impregnation Process ◽  
Low Concentrations

Biolaminates of Ixtle and Henequen natural fibers reinforced bio-based epoxy resin were prepared using Vacuum Assisted Resin Infusion process. ZnO nanoparticles were added to the bio-based epoxy resin at 1, 2 and 3 wt. % content before impregnation process. The viscoelastic and mechanical properties, as well as the fracture behavior, were evaluated and related to the nature of the fibers and filler content. The viscoelastic results indicated the ZnO particles are effective fillers just at low concentrations, and induce different reinforcement mechanisms attributed to the interaction between the nature of fibers and nanoparticles. The mechanical properties of the Ixtle biolaminates decreased at higher filler concentrations, while Henequen biolaminates showed better mechanical properties just above the 2 wt. % of ZnO. The fracture behavior in mode I registered moderate changes in toughness, related to the ZnO fraction, which promoted different behaviors on the interlaminar adherence of the layers. The results point to the need to continue evaluating the potential application of these green composites for their use in construction and automotive industries.

Effect of Fiber Parameters on the Mechanical Properties of Banana-Glass Fiber Hybrid Composites

2014 ◽  
Vol 592-594 ◽  
pp. 202-205
Author(s):  
V. Santhanam ◽  
M. Chandrasekaran ◽  
N. Venkateshwaran
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Glass Fiber ◽  
Fiber Length ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Synthetic Fiber

Composite materials are widely used for their superior properties such as high strength to weight ratio, high tensile strength, low thermal expansion, low density etc. Due to environmental issues the eco-friendly composites are being explored. Natural fibers as reinforcement for polymer composites are widely studied. But natural fibers lack better mechanical properties when compared with synthetic fibers. Hence mixing the natural fiber with a synthetic fiber such as glass fiber will improve mechanical properties of the composites. In this study banana fiber is mixed with glass fiber, and the mixture is used as reinforcement in epoxy matrix. The composite specimens were prepared using hand layup technique, the fibers were randomly oriented. Further the fiber length was varied as 10, 15, 20 and 25mm and volume fraction as 10%, 15%, 20% and 25%. Experiments were conducted to find the effect of fiber length and volume fraction on tensile strength, flexural strength, water absorption properties of the composites. It is observed that a fiber length of 20mm and 20% fiber volume fraction gave better mechanical properties.

scholarly journals Mechanical Properties of Short Polymer Fiber-Reinforced Geopolymer Composites

2020 ◽  
Vol 4 (3) ◽  
pp. 128 ◽  
Author(s):  
Kinga Korniejenko ◽  
Wei-Ting Lin ◽  
Hana Šimonová
Keyword(s):  
Mechanical Properties ◽  
Construction Industry ◽  
Polymer Fiber ◽  
Short Fibers ◽  
Potential Applications ◽  
Fiber Reinforcements ◽  
New Material ◽  
Materials Used ◽  
Long Fibers ◽  
Geopolymer Composites

The article describes the state of the art in reinforced geopolymers, taking into consideration various types of polymer fiber reinforcements, such as polypropylene, polyethylene, or polylactic acid. The description is focused on the usage of polymer short fibers and the mechanical properties of the geopolymer composites. However, to show a wider research background, numerous references are discussed concerning the selected studies on reinforcing geopolymer composites with long fibers and fabrics. The research method applied in the article is the critical analysis of literature sources, including a comparison of new material with other materials used in similar applications. The results of the research are discussed in a comparative context and the properties of the composites are juxtaposed with the properties of the standard materials used in the construction industry. Potential applications in the construction industry are presented. Moreover, the contemporary research challenges for geopolymer materials reinforced with fibers are presented.

Current literature review on methods for measuring the stability of osseointegrable implants.

2020 ◽  
Vol 2 (4) ◽  
pp. 64-78
Author(s):  
Noha El-Wassefy ◽  
Lars Sennerby ◽  
Dhoom SIngh Mehta ◽  
Thiago De Santana Santos
Keyword(s):  
Literature Review ◽  
Current Literature ◽  
Implant Survival ◽  
Implant Stability ◽  
Implant Placement ◽  
Factors Influencing ◽  
Case Documentation ◽  
Bone To Implant Contact ◽  
The Stability

“Osseointegration” as formulated by Alberktson is crucial for implant survival and success. Osseointegration is a measure of implant stability. Measuring implant stability helps to arrive at decisions as to loading of an implant, allows choice of protocol on a patient to patient basis and provides better case documentation. A successful implant reflects good bone to implant contact and is determined by implant stability both primary and secondary. Implant stability is achieved at two different stages – primary (immediately after implant placement) and secondary (3-4 months after implant placement). Implant stability has been confirmed to affect the process of osseointegration and therefore is essential to understand the methods to measure implant stability and factors influencing. Various methods are developed to assess implant stability which suggests the prognosis of an implant.

scholarly journals Mechanical Properties of Mortars Reinforced with Amazon Rainforest Natural Fibers

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 155
Author(s):  
Régis Pamponet da Fonseca ◽  
Janaíde Cavalcante Rocha ◽  
Malik Cheriaf
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Natural Fibers ◽  
Construction Materials ◽  
Hot Water ◽  
Amazon Rainforest ◽  
Hot Water Treatment ◽  
Composite Binder ◽  
Naoh Solution ◽  
Reference Samples

The addition of natural fibers used as reinforcement has great appeal in the construction materials industry since natural fibers are cheaper, biodegradable, and easily available. In this work, we analyzed the feasibility of using the fibers of piassava, tucum palm, razor grass, and jute from the Amazon rainforest as reinforcement in mortars, exploiting the mechanical properties of compressive and flexural strength of samples with 1.5%, 3.0%, and 4.5% mass addition of the composite binder (50% Portland cement + 40% metakaolin + 10% fly ash). The mortars were reinforced with untreated (natural) and treated (hot water treatment, hornification, 8% NaOH solution, and hybridization) fibers, submitted to two types of curing (submerged in water, and inflated with CO2 in a pressurized autoclave) for 28 days. Mortars without fibers were used as a reference. For the durability study, the samples were submitted to 20 drying/wetting cycles. The fibers improved the flexural strength of the mortars and prevented the abrupt rupture of the samples, in contrast to the fragile behavior of the reference samples. The autoclave cure increased the compressive strength of the piassava and tucum palm samples with 4.5% of fibers.

Sign in / Sign up

Export Citation Format

Share Document