Effect of Alkaline Activator Ratio to Mechanical Properties of Geopolymer Concrete with Trass as Filler

2015 ◽  
Vol 754-755 ◽  
pp. 406-412 ◽  
Author(s):  
Puput Risdanareni ◽  
Januarti Jaya Ekaputri ◽  
Mohd Mustafa Al Bakri Abdullah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Sodium Silicate ◽  
Setting Time ◽  
Geopolymer Concrete ◽  
Closed Porosity ◽  
Split Tensile Strength ◽  
Alkaline Activator ◽  
Test Result

This paper describes the effect of alkaline activator ratio (Na2SiO3/NaOH) to mechanical properties of geopolymer concrete. The mechanical properties of geopolymer concrete were assessed by setting time, split tensile strength and porosity. Fly ash was used as a cement substitute, and trass used as filler. While, Natrium hydroxide (NaOH) and Sodium Silicate (Na2SiO3) was applied as alkaline activator. In this study, NaOH concentration eight and ten molar with an alkaline activator ratio Na2SiO3/ NaOH by mass: 0.5, 1, 1.5, 2 and 2.5 were used. The test result showed that setting time, porosity and split tensile strength of geopolymer concrete were hardly influenced by NaOH concentration and the alkaline activator ratio. The alkaline activator ratio of Na2SiO3/NaOH has an optimum value at 2 and 2.5. Test result showed that the fastest setting time was 25 minute, the highest amount of closed porosity was 9.035 % and the highest split tensile strength was 2.86 MPa.

Physical Properties of Volcanic Ash Based Geopolymer Concrete

2016 ◽  
Vol 841 ◽  
pp. 1-6 ◽  
Author(s):  
Puput Risdanareni ◽  
Adjib Karjanto ◽  
Febriano Khakim
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Volcanic Ash ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Ash Content ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Time Test

This paper describes the result of investigating volcanic ash of Mount Kelud as fly ash substitute material to produce geopolymer concrete. The test was held on geopolymer concrete blended with 0%, 25%, 50% and 100% fly ash replacement with volcanic ash. Natrium Hidroxide (NaOH) with concentration of 12 molar and Natrium Silicate (Na2SiO3) were used as alkaline activator. While alkali-activator ratio of 2 was used in this research. The physical properties was tested by porosity and setting time test, while split tensile strength presented to measure brittle caracteristic of geopolymer concrete. The result shown that increasing volcanic ash content in the mixture will increase setting time of geopolymer paste. On the other hand increasing volcanic ash content will reduce split tensile strength and porosity of geopolymer concrete. After all replacing fly ash with volcanic ash was suitable from 25% to 50% due to its optimum physical and mechanical properties.

Properties of slag geopolymer concrete modified with fly ash and silica fume

2021 ◽  
Author(s):  
Hafez Elsayed Elyamany ◽  
Abd Elmoaty Mohamed Abd Elmoaty ◽  
Abdul Rahman Ahmed Diab
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Setting Time ◽  
Splitting Tensile Strength ◽  
Geopolymer Concrete ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Additional Water

This research focused on the role of fly ash and silica fume on slag geopolymer concrete through investigating workability (slump, and slump loss), initial setting time, final setting time, and mechanical properties of slag geopolymer concrete, S-GPC, (compressive strength, splitting tensile strength, modulus of elasticity) in addition to SEM (Scanning electron microscope), and X-Ray analysis. The considered variables included, fly ash (FA) content as a replacement of ground granulated blast furnace slag (GS) (0, 10, 20, 30, and 40 %), presence of silica fume (SF) as a replacement of slag, concentration of sodium hydroxide, NaOH, (molarity: 10M, 16M, and 18M), additional water content (7.5,11,14, and 20 %), and curing type (thermal, air, and water curing). S-GPC yielded rapid stiffening and high slump loss with high mechanical properties. The use of silica fume or fly ash or a mix of them enhanced workability, decreased rate of slump loss, and delayed setting time. ACI 318 equation over estimates splitting tensile strength of FS-GPC.

scholarly journals Geopolymer Concrete under Ambient Curing

2021 ◽  
Author(s):  
M. Indhumathi Anbarasan ◽  
S.R. Sanjaiyan ◽  
S. Nagan Soundarapandiyan
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Setting Time ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Carbon Footprints ◽  
Curing Conditions ◽  
Ambient Curing

Geopolymer concrete (GPC) has significant potential as a more sustainable alternative for ordinary Portland cement concrete. GPC had been introduced to reduce carbon footprints and thereby safeguarding environment. This emerging eco friendly construction product finds majority of its application in precast and prefabricated structures due to the special curing conditions required. Sustained research efforts are being taken to make the product suitable for in situ applications. The developed technology will certainly address the issues of huge energy consumption as well reduce water use which is becoming scarce nowadays. Ground Granulated Blast Furnace Slag (GGBS) a by-product of iron industries in combination with fly ash has proved to give enhanced strength, durability as well reduced setting time. This study investigates the effect of GGBS as partial replacement of fly ash in the manufacture of GPC. Cube and cylindrical specimens were cast and subjected to ambient curing as well to alternate wetting-drying cycles. The 28 day compressive strength, split tensile strength, flexural strength and density of GPC specimens were found. The study revealed increase in compressive strength, split tensile strength, density as well flexural strength up to 40 percent replacement of fly ash by GGBS.

scholarly journals An Experimental Study on Fibre Reinforced Geopolymer Concrete Composites- Glass Fibre, Copper Slag

2018 ◽  
Vol 7 (3.34) ◽  
pp. 433
Author(s):  
J Asanammal Saral ◽  
S Gayathri ◽  
M Tamilselvi ◽  
B Raghul Raj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Thermal Power ◽  
Copper Slag ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Split Tensile Strength

The major problem of the world is facing today is environmental pollution. It is well known that for the production of 1-ton of cement consumes more energy and exhibit 0.8-ton of CO2 .On the other hand Fly ash is a residue from the combustion of pulverized coal from the flue gases of thermal power plant. Recently, the fly ash is not effectively used and a large part of it is disposed in landfill. Due to this problem the various researchers have sort for a new binder to minimize the consumption of OPC. This study evaluates the strength of geopolymer concrete having fly ash as the major binding material and the sand a fine aggregate was replaced with copper slag of 40%  and glass fiber to enhance the mechanical properties have been presented. This paper analyses on the mechanical properties of eopolymer concrete composites such as compressive strength, split tensile strength and water absorption in heat curing at 60˚C for 24 hrs in hot air oven. Glass fibers were added in the mix in the volume fraction of 0.5%, 1.0%, 1.5% and 2.0% volume of the concrete. The influence of fiber content in terms of volume fraction on the compressive, split tensile strength of geopolymer concrete is presented. The result shows the elevated performance of the properties exhibited by the geopolymeric concrete with and without fibres.

Effect of Quantity of Industrial Waste on Eco-Friendly Geopolymer Concrete

2021 ◽  
Vol 1019 ◽  
pp. 102-109
Author(s):  
Endow Mazumder ◽  
L.V. Prasad M.
Keyword(s):  
Tensile Strength ◽  
Polymerization Process ◽  
Strength Increase ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Granulated Blast Furnace Slag ◽  
Activating Agent ◽  
Alkaline Activator ◽  
Binder Material ◽  
Tensile Strength Increase

The primary goal of this work is to report the results of the experimental outcome of Geopolymer concrete (GEO-C) which is prepared and cured at room temperature. GEO-C is prepared using a blend of ground granulated blast furnace slag (GGSG) and F Class Fly Ash, and the replacement is ranged from 0% to 100% of binder material, to find the optimum dosage of binder material. Sodium Hydroxide (NaOH) and Sodium Silicate (Na2SiO3) which are alkaline in nature, used primarily as an activating agent for the polymerization process of geopolymer. Experiments were conducted on samples by fixing the NaOH concentration as 14M for optimum strength and the alkaline activator ratio is fixed as one. Mechanical properties of GEO-C like compressive strength, rupture modulus (i.e. flexural strength), and split tensile strength were evaluated at the ages 7, 14, 28 days. From the results, it is observed that with the addition of GGSG in the blend the compressive, flexural, and tensile strength increase but there is a drastic reduction in the workability of the mixture.

scholarly journals Developing Geopolymer Concrete Properties by Using Nanomaterials and Steel Fibers

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
E. Rabiaa ◽  
R. A. S. Mohamed ◽  
W. H. Sofi ◽  
Taher A. Tawfik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Sodium Hydroxide ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Hardened Concrete ◽  
Geopolymer Concrete ◽  
Alkaline Activator ◽  
The Impact

This research investigates the simultaneous impact of two different types of steel fibers, nanometakaolin, and nanosilica on the mechanical properties of geopolymer concrete (GPC) mixes. To achieve this aim, different geopolymer concrete mixes were prepared. Firstly, with and without nanomaterials (nanosilica and nanometakaolin) of 0, 2%, 4%, 6%, and 8% from ground granulated blast furnace slag (GGBFS) were used. Secondly, steel fiber (hooked end and crimped) content of (0, 0.5%, 1, and 1.5%) was used. Thirdly, optimum values of nanomaterials with the optimum values of steel fiber were used. Crimped and hooked-end steel fibers were utilized with an aspect ratio of 60 and a length of 30 mm. Geopolymer mixes were manufactured by using a constant percentage of alkaline activator to binder proportion equal to 0.45 with GGBFS cured at ambient conditions. For alkaline activator, sodium hydroxide molar (NaOH) and sodium hydroxide solution (NaOH) were used according to a proportion (Na2SiO3/NaOH) of 2.33. The hardened concrete tests were performed through the usage of splitting tensile strength, flexural, and compressive experiments to determine the impact of steel fibers, nanometakaolin, and nanosilica individually and combined on performance of GPC specimens. The results illustrated that using a mix composed of the optimum steel fibers (1% content) accompanied by an optimum percentage of 6% nanometakaolin or 4% nanosilica demonstrated a significant enhancement in the mechanical properties of GPC specimens compared to all other mixtures. Besides, the impact of using nanomaterials individually was found to be predominant on compressive strength on GPC specimens especially with the usage of the optimum values. However, using nanomaterials individually compared to using the steel fibers individually was found to have approximately the same splitting tensile strength and flexural performance.

scholarly journals Effect of Carboxylic Acid (Benzene Crystallable) in Cement Concrete and Geopolymer Concrete

2020 ◽  
Vol 9 (7) ◽  
pp. 472-475
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Carboxylic Acid ◽  
Geopolymer Concrete ◽  
Cement Concrete ◽  
Split Tensile Strength ◽  
Sealing Capacity ◽  
Time Period

The present study appraises the recitals of carboxylic acid- based admixture to increase concrete water tightness and self-sealing capacity of the cement and geopolymer concrete. Outcomes of the previous studies in particular, adding 1% by cement mass of the carboxylic polymer reasons for reduction in the water dispersion under pressure of 7-day wet cured concrete by 50% associated to that of the conforming reference concrete. At 7 days, M4 mix compressive strength is about 43.5% less than M3 mix. The compressive strength of M4 increases and is about 37.6% less than M3 mix at 28 days of curing. At 7 days, M4 mix split tensile strength is about 17.5% less than M3 mix (cement concrete with 0.45 w/c ratio). The split tensile strength of M4 declines and is about 42.3% less than M3 mix at 28 days of curing. The strength of the geopolymer concrete tends to increase as the time period increases due to the presence of fly ash in it. So it is expected that geopolymer concrete will give more strength than cement concrete in long term with the presence of carboxylic acid

scholarly journals Use of waste paper ash or wood ash as substitution to fly ash in production of geopolymer concrete

2021 ◽  
Vol 30 (3) ◽  
pp. 464-476
Author(s):  
Haider Owaid ◽  
Haider Al-Baghdadi ◽  
Muna Al-Rubaye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Wood Ash ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Geopolymer Concrete

Large quantities of paper and wood waste are generated every day, the disposal of these waste products is a problem because it requires huge space for their disposal. The possibility of using these wastes can mitigate the environmental problems related to them. This study presents an investigation on the feasibility of inclusion of waste paper ash (WPA) or wood ash (WA) as replacement materials for fly ash (FA) class F in preparation geopolymer concrete (GC). The developed geopolymer concretes for this study were prepared at replacement ratios of FA by WPA or WA of 25, 50, 75 and 100% in addition to a control mix containing 100% of FA. Sodium hydroxide (NaOH) solutions and sodium silicate (Na2SiO3) are used as alkaline activators with 1M and 10M of sodium hydroxide solution.The geopolymer concretes have been evaluated with respect to the workability, the compressive strength, splitting tensile strength and flexural strength. The results indicated that there were no significant differences in the workability of the control GC mix and the developed GC mixes incorporating WPA or WA. Also, the results showed that, by incorporating of 25–50% PWA or 25% WA, the mechanical properties (compressive strength, splitting tensile strength and flexural strength) of GC mixes slightly decreased. While replacement with 75–100% WPA or with 50–100% WA has reduced these mechanical properties of GC mixes. As a result, there is a feasibility of partial replacement of FA by up to 50% WPA or 25% WA in preparation of the geopolymer concrete.

scholarly journals Mechanical properties of concrete composed of sintered fly ash lightweight aggregate

2018 ◽  
Vol 195 ◽  
pp. 01008
Author(s):  
Puput Risdanareni ◽  
Januarti Jaya Ekaputri ◽  
Ike Maulidiyawati ◽  
Poppy Puspitasari
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Lightweight Aggregate ◽  
Effective Solution ◽  
Binding Agent ◽  
Split Tensile Strength ◽  
Bonded Method

This paper investigates the effect of sintered fly ash lightweight aggregate as coarse aggregate substitution on the mechanical properties of concrete. The lightweight aggregate (LWA) was produced using the cold bonded method and then sintered at a temperature of 900°C. An alkaliactivated system was applied as a binding agent of the LWA. Fly ash was used as precursor while sodium hydroxide and sodium silicate were employed as alkali activators. Three variations of the LWA dosage were performed, which were 0%, 50%, and 100 % of the volume of coarse aggregate in the concrete mixture. The mechanical properties of the concrete investigated in this research are the compressive strength and split tensile strength. The result showed that the mechanical properties of the concrete slightly decrease along with the increased dosage of the LWA in the mixture. However, employing sintered fly ash the LWA is proven as an effective solution in reducing the concrete density without sacrificing its strength.

scholarly journals A Comprehensive Study on the Factors Affecting the Workability and Mechanical Properties of Ambient Cured Fly Ash and Slag Based Geopolymer Concrete

2021 ◽  
Vol 11 (18) ◽  
pp. 8722
Author(s):  
Rana Muhammad Waqas ◽  
Faheem Butt ◽  
Xulong Zhu ◽  
Tianshui Jiang ◽  
Rana Faisal Tufail
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Geopolymer Concrete ◽  
Factors Affecting ◽  
Naoh Solution ◽  
New Material ◽  
Comprehensive Study ◽  
Slag Content

Geopolymer concrete (GPC), also known as an earth friendly concrete, has been under continuous study due to its environmental benefits and potential as a sustainable alternative to conventional concrete construction. However, there is still a lack of comprehensive studies focusing on the influence of all the design mix variables on the fresh and strength properties of GPC. GPC is still a relatively new material in terms of field application and has yet to secure international acceptance as a construction material. Therefore, it is important that comprehensive studies be carried out to collect more reliable information to expand this relatively new material technology to field and site applications. This research work aims to provide a comprehensive study on the factors affecting the fresh and hardened properties of ambient cured fly ash and slag based geopolymer concrete (FS-GPC). Industrial by-products, fly ash from thermal power plants, and ground granulated blast furnace slag from steel industries were utilized to produce ambient cured FS-GPC. A series of experiments were conducted to study the effect of various parameters, i.e., slag content (10%, 20%, 30%, and 50%), amount of alkaline activator solution (AAS) (35% and 40%), sodium silicate (SS) to sodium hydroxide (SH) ratio (SS/SH = 2.0, 2.5 and 3.0), sodium hydroxide concentration (10 M, 12 M, and 14 M) and addition of extra water on fresh and mechanical properties of FS-GPC. The workability of the fresh FS-GPC mixes was measured by the slump cone test. The mechanical properties of the mixes were evaluated by compressive strength, split tensile strength, flexure strength, and static modulus tests. The results revealed that workability of FS-GPC is greatly reduced by increasing slag content, molarity of NaOH solution, and SS/SH ratio. The compressive strength was improved with an increase in the molarity of NaOH solution and slag content and a decrease in AAS content from 40% to 35%. However, the influence of SS/SH ratio on mechanical properties of FS-GPC has a varying effect. The addition of extra water to enhance the workability of GPC matrix caused a decrease in the compressive strength. The validity of the equations suggested by previous studies to estimate the tensile and flexural strength and elastic modulus of FS-GPC mixes were also evaluated. Based on the test results of this study, empirical equations are proposed to predict the splitting tensile strength, flexural strength, and elastic modulus of ambient cured FS-GPC. The optimal mixtures of FS-GPC in terms of workability and mechanical properties were also proposed for the field applications.

Sign in / Sign up

Export Citation Format

Share Document