Effects of Ultrasonic Treatment on Microstructure and Properties of Al-Based Composites Reinforced by In Situ Al2O3 Nanoparticles

2016 ◽  
Vol 35 (2) ◽  
pp. 169-175
Author(s):  
Cunguang Chen ◽  
Zhimeng Guo ◽  
Ji Luo ◽  
Wenwen Wang ◽  
Junjie Hao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultrasonic Treatment ◽  
Tensile Tests ◽  
Al2o3 Nanoparticles ◽  
Displacement Reaction ◽  
Slight Improvement ◽  
Intermetallic Particles ◽  
Microstructural Effects

AbstractAn investigation on the microstructure of as-cast Al-Mg-Cu composites reinforced by in situ nano-sized Al2O3 dispersoids with ultrasonic treatment showed that ultrasonic treatment of the melt prior to casting had a significant effect on the size and sphericity of α-Al dendrites as well as on the size, continuity and sphericity of intermetallic particles (Al2CuMg) formed during cooling and solidification of the composite. More importantly, Al2O3 nanoparticles were uniformly distributed inside the grains, which were in situ produced by the displacement reaction between Al and CuO in the melt under ultrasonic treatment. The microstructural effects were mainly attributed to the cavitation and streaming phenomena which took place during ultrasonic treatment in the melt. The mechanical properties were investigated by tensile tests and hardness measurements. Ultrasonic treatment caused a significant increase in the yield strength (~43%), ultimate tensile strength (~32%) and hardness (~13%), and simultaneously slight improvement in the ductility.

The Research of Poly Propylene Carbonate /Nano-SiO2 Composites

2014 ◽  
Vol 904 ◽  
pp. 74-77 ◽  
Author(s):  
Qu Li ◽  
Heng Wu ◽  
Si Yuan Xie ◽  
Jiao Sun ◽  
Xing Hai Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Glass Transition ◽  
Transition Temperature ◽  
Propylene Carbonate ◽  
Tensile Tests ◽  
Slight Improvement ◽  
Biodegradable Poly ◽  
Poly Propylene

Biodegradable poly (propylene carbonate) (PPC) composite with a slight improvement in the thermal stability and tensile strength was successfully prepared by incorporating a low content of nano-SiO2. Tensile tests demonstrate the better mechanical properties of the composites prepared in this study. The obtained composites increases sharply from 1.57Mpa to 12.04Mpa by incorporating 5wt% nano-SiO2. Furthermore, the composites show approximately 8°C higher glass transition temperature (Tg) than that of neat PPC.The Tdmax of composite with 5wt% of nano-SiO2 was about 40°C higher than that of neat PPC.

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

scholarly journals Mimicking the Mechanical Properties of Aortic Tissue with Pattern-Embedded 3D Printing for a Realistic Phantom

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5042
Author(s):  
Jaeyoung Kwon ◽  
Junhyeok Ock ◽  
Namkug Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Aortic Wall ◽  
Tensile Tests ◽  
Human Aorta ◽  
Aortic Tissue ◽  
Medical Field ◽  
Base Materials

3D printing technology has been extensively applied in the medical field, but the ability to replicate tissues that experience significant loads and undergo substantial deformation, such as the aorta, remains elusive. Therefore, this study proposed a method to imitate the mechanical characteristics of the aortic wall by 3D printing embedded patterns and combining two materials with different physical properties. First, we determined the mechanical properties of the selected base materials (Agilus and Dragonskin 30) and pattern materials (VeroCyan and TPU 95A) and performed tensile testing. Three patterns were designed and embedded in printed Agilus–VeroCyan and Dragonskin 30–TPU 95A specimens. Tensile tests were then performed on the printed specimens, and the stress-strain curves were evaluated. The samples with one of the two tested orthotropic patterns exceeded the tensile strength and strain properties of a human aorta. Specifically, a tensile strength of 2.15 ± 0.15 MPa and strain at breaking of 3.18 ± 0.05 mm/mm were measured in the study; the human aorta is considered to have tensile strength and strain at breaking of 2.0–3.0 MPa and 2.0–2.3 mm/mm, respectively. These findings indicate the potential for developing more representative aortic phantoms based on the approach in this study.

Test Methods for Mechanical Properties of Structural Adhesives

2010 ◽  
Vol 97-101 ◽  
pp. 814-817 ◽  
Author(s):  
Jun Deng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Butt Joint ◽  
Test Methods ◽  
Joint Specimen ◽  
Lap Shear ◽  
Better Than

One of the greatest drawbacks to predicting the behaviour of bonded joints has been the lack of reliable data on the mechanical properties of adhesives. In this study, methods for determining mechanical properties of structural adhesive were discussed. The Young’s modulus, Poisson’s ratio and tensile strength of the adhesive were tested by dogbone specimens (bulk form) and butt joint specimens (in situ form). The shear modulus and shear strength were test by V-notched specimens (bulk form) and thick adherend lap-shear (TALS) joint specimens (in situ form). The test results show that the elastic modulus provided by the manufacturer is too low, the dogbone specimen is better than the butt joint specimen to test the tensile strength and elastic modulus and the TALS joint specimen is better than the V-notched specimen to test the shear strength.

The Investigation on Aluminium Alloys Automobile Wheel with Low-Titanium Content Produced by Electrolysis

2005 ◽  
Vol 475-479 ◽  
pp. 317-320 ◽  
Author(s):  
Jing Pei Xie ◽  
Ji Wen Li ◽  
Zhong Xia Liu ◽  
Ai Qin Wang ◽  
Yong Gang Weng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloys ◽  
Solution Treatment ◽  
A356 Alloy ◽  
Aging Treatment ◽  
Titanium Content ◽  
The Matrix ◽  
Automobile Wheel

The in-situ Ti alloying of aluminium alloys was fulfilled by electrolysis, and the material was made into A356 alloy and used in automobile wheels. The results show that the grains of the A356 alloy was refined and the second dendrites arm was shortened due to the in-situ Ti alloying. Trough 3-hour solution treatment and 2-hour aging treatment for the A356 alloy, the microstructures were homogeneous, and Si particles were spheroid and distribute in the matrix fully. The outstanding mechanical properties with tensile strength (σb≥300Mpa) and elongation values (δ≥10%) have been obtained because the heat treatment was optimized. Compared with the traditional materials, tensile strength and elongation were increased by 7.6~14.1% and 7.4~44.3% respectively. The qualities of the automobile wheels were improved remarkably.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

Effect of Plastic Deformation on the Mechanical Properties and Microstructure of Homogenized AZ80 Magnesium Alloy

2010 ◽  
Vol 139-141 ◽  
pp. 180-184
Author(s):  
Yong Xue ◽  
Zhi Min Zhang ◽  
Li Hui Lang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Grain Boundaries ◽  
Gradual Increase ◽  
Tensile Tests ◽  
Extrusion Ratio ◽  
Extrusion Temperature ◽  
Second Phase ◽  
Strength And Plasticity ◽  
Az80 Alloy

In the present research, the influences of different extrusion ratios (15, 30, 45, 60, and 75) and extrusion temperatures (300°C, 330°C, 360°C, 390°C, 420°C) on the mechanical properties and microstructure of homogenized AZ80 alloy have been investigated through the tensile tests and via metallographic microscope observation. The results show that the alloy’s grain is small and small amounts of black hard and brittle second-phase β (Mg17Al12) are precipitated uniformly along the grain boundary causing the gradual increase of the alloy’s tensile strength at 330°C. When the extrusion temperature is up to 390°C, the grain size increases significantly, but the second phase precipitation along grain boundaries transforms into continuous and uniform-distribution precipitation within the grain. In this case, when the extrusion ratio is 60, the alloy’s tensile strength reaches its peak 390Mpa. As the extrusion temperature increases, inhomogeneous precipitation of the second-phase along grain boundaries increases, causing the decrease of the alloy’s strength. At the same temperature, the tensile strength increases firstly and then decreases as extrusion ratio increases. With the gradual increase of the refinement grain, the dispersed precipitates increase and the alloy’s tensile strength and plasticity reach their peaks when the extrusion temperature is 390°C. As the grain grows, the second phase becomes inhomogeneous distribution, and the alloy’s strength and plasticity gradually decrease.

Mechanical And Superconducting Properties Of Cu-Nb3Sn In Situ Produced Composite Wires

1981 ◽  
Vol 12 ◽  
Author(s):  
A. Kolb-Telieps ◽  
B.L. Mordike ◽  
M. Mrowiec
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Wide Temperature Range ◽  
Volume Fraction ◽  
Superconducting Properties ◽  
Temperature Range ◽  
Composite Wires ◽  
Strength And Ductility

ABSTRACTCu-Nb composite wires were produced from powder, electrolytically coated with tin and annealed to convert the Nb fibres to Nb 3Sn. The content was varied between 10 wt % and 40 wt %. The superconducting properties of the wires were determined. The mechanical properties, tensile strength, yield strength and ductility were measured as a function of volume fraction and deformation over a wide temperature range. The results are compared with those for wires produced by different techniques.

Forming Behaviour of Al-TiC In Situ Composites

2013 ◽  
Vol 765 ◽  
pp. 418-422 ◽  
Author(s):  
Ram Naresh Rai ◽  
A.K. Prasada Rao ◽  
G.L. Dutta ◽  
M. Chakraborty
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Uniform Distribution ◽  
Interface Bonding ◽  
Microstructure And Mechanical Properties ◽  
Micron Size ◽  
Forming Behaviour ◽  
Al Matrix

The forming behaviour of in-situ Al-TiC composites was investigated by comparing microstructure and mechanical properties of as-cast, forged and rolled specimens. The microstructures of forged and rolled specimens reveal uniform distribution of the TiC particles, which are responsible for the enhancement of the tensile strength of the composite. The formed samples were found to be crack free. This feature is very likely to be due to good interface bonding of uniformly dispersed sub-micron size TiC particles with the Al matrix.

scholarly journals MICROSTRUCTURE RESEARCH OF THE UNIDIRECTIONAL ORGANOPLASTIC BASED ON RUSAR-NT ARAMID FIBERS AND EPOXY-POLYSULFONE BINDER

2020 ◽  
pp. 19-26
Author(s):  
E.N. Kablov ◽  
◽  
G.S. Kulagina ◽  
G.F. Zhelezina ◽  
S.L. Lonskii ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Polymer Matrix ◽  
Packing Density ◽  
Tensile Tests ◽  
Polymer Composite Material ◽  
Aramid Fibers ◽  
Before And After ◽  
Binder Structure

This paper studies a polymer composite material - a unidirectional organoplastic based on Rusar-NT aramid fiber and a melt epoxy-polysulfone binder. Organoplastic has the following mechanical properties: tensile strength 2060 MPa, Young's modulus 101 GPa. The microstructure of the fiber and the polymer matrix in the organoplastic samples was studied before and after tensile tests. The features of the formation of the binder structure depending on the packing density of the fibers in organoplastics have been determined. The nature of the destruction of fibers and polymer matrix caused by the uniaxial tension has been studied.

Sign in / Sign up

Export Citation Format

Share Document