scholarly journals Enhancement of the mechanical properties of HDPE mineral nanocomposites by filler particles modulation of the matrix plastic/elastic behavior

2022 ◽  
Vol 11 (1) ◽  
pp. 312-320
Author(s):  
Yousef Murtaja ◽  
Lubomír Lapčík ◽  
Harun Sepetcioglu ◽  
Jakub Vlček ◽  
Barbora Lapčíková ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Performance ◽  
Plant Production ◽  
Elastic Behavior ◽  
Indentation Modulus ◽  
Transmission Electron ◽  
The Matrix ◽  
Poly Ethylene ◽  
Mineral Fillers

Abstract Two different nanosized mineral fillers (nano calcium carbonate and nanoclay) were used in the high density poly(ethylene) (HDPE) composites pilot plant production. Structural and mechanical properties of the prepared composites were examined in this study. The homogenous filler distribution was confirmed in the tested samples by scanning electron microscopy, transmission electron microscopy, and energy dispersive spectroscopy analyses. The fillers’ fortifying effect on polymer composites’ mechanical performance was confirmed as indicated by the increased elastic modulus and indentation modulus. Additionally, the possible modulation of the plastic-elastic mechanical behavior was confirmed by the type of the filler as well as its concentration used in the final composites testing articles.

scholarly journals TEM observation of precipitates and their role to mechanical properties in Ti-5553 alloy heated to some temperatures up to 923 K

2020 ◽  
Vol 321 ◽  
pp. 11035
Author(s):  
E. Sukedai ◽  
E. Aeby-Gautier ◽  
M. Dehmas
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Hardening Mechanism ◽  
Transmission Electron ◽  
The Matrix ◽  
Higher Temperature ◽  
Shearing Mechanism ◽  
Hardness Values ◽  
Measured Hardness

A Ti-5553 specimen was continuously heated to 923 K and simultaneously in-situ HEXRD profiles were taken. In addition, specimens heated at the same rate to several temperatures up to 923 K and further quenched were observed by transmission electron microscopy. Based on both results obtained, transformation sequence was clarified, precipitations of ω-, α”iso- and α-phases were confirmed, and size and density of these precipitates were measured. Hardness values of those specimens were also measured. The hardening mechanism was considered as shearing-mechanism for specimens aged at lower temperatures and by-pass one for specimens aged at higher temperature. An attempt of distinction between α”iso - and α-precipitates was also tried. Both precipitates were in needle-like shape and a possibility was suggested by measuring angles between two needle-shape precipitates on {110} of the matrix and comparing with each other.

scholarly journals Effect of Two-Stage Homogenization Heat Treatment on Microstructure and Mechanical Properties of AA2060 Alloy

Crystals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 40
Author(s):  
Chaoyang Chaoyang ◽  
Guangjie Guangjie ◽  
Lingfei Lingfei ◽  
Fei Fei ◽  
Lin Lin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Cast Alloy ◽  
Hardness Test ◽  
Test Methods ◽  
Al Alloy ◽  
Two Stage ◽  
Homogenization Treatment ◽  
Transmission Electron ◽  
The Matrix

The microstructure evolution of AA2060 Al alloy containing Li during two-stage homogenization treatment was investigated by optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), differential scanning calorimeter (DSC), transmission electron microscopy (TEM), mechanical properties and Vickers micro-hardness test methods. The results demonstrate that severe precipitation of θ(Al2Cu) and S(Al2CuMg) phase existed in the as-cast alloy, especially in the center position. Cu elements were concentrated at grain boundary and gradually decreased from the boundary to the interior. Numerous eutectic phases of θ(Al2Cu) and S (Al2CuMg) containing Zn and Ag elements were segregated at grain boundaries. The overheating temperature of the as-cast alloy is 497 °C. After two-stage homogenization treatment, the θ(Al2Cu) and S (Al2CuMg) in the surface, middle and center positions were completely dissolved into the matrix, thus achieved uniform homogenization effect. Moreover, water cooling could prevent the precipitation after homogenization, which provided good performance of the studied alloy. The optimum two-stage homogenization treatment of AA2060 alloy was 460 °C/4 h + 490 °C/2 4 h. The homogenization kinetic analysis was discussed as well.

scholarly journals Enhancement of Mechanical and Thermal Properties of Polylactic Acid/Polycaprolactone Blends by Hydrophilic Nanoclay

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Chern Chiet Eng ◽  
Nor Azowa Ibrahim ◽  
Norhazlin Zainuddin ◽  
Hidayah Ariffin ◽  
Wan Md. Zin Wan Yunus ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Polylactic Acid ◽  
Mechanical Analysis ◽  
Basal Spacing ◽  
Mechanical And Thermal Properties ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
The Matrix ◽  
Thermal Stability Of

The effects of hydrophilic nanoclay, Nanomer PGV, on mechanical properties of Polylactic Acid (PLA)/Polycaprolactone (PCL) blends were investigated and compared with hydrophobic clay, Montmorillonite K10. The PLA/PCL/clay composites were prepared by melt intercalation technique and the composites were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). FTIR spectra indicated that formation of hydrogen bond between hydrophilic clay with the matrix. XRD results show that shifting of basal spacing when clay incorporated into polymer matrix. TEM micrographs reveal the formation of agglomerate in the composites. Based on mechanical properties results, addition of clay Nanomer PGV significantly enhances the flexibility of PLA/PCL blends about 136.26%. TGA showed that the presence of clay improve thermal stability of blends. DMA show the addition of clay increase storage modulus and the presence of clay Nanomer PGV slightly shift two Tg of blends become closer suggest that the presence of clay slightly compatibilizer the PLA/PCL blends. SEM micrographs revealed that presence of Nanomer PGV in blends influence the miscibility of the blends. The PLA/PCL blends become more homogeneous and consist of single phase morphology.

Electron Microscopy of Irradiated and Mechanically Tested Tungsten

1967 ◽  
Vol 25 ◽  
pp. 314-315
Author(s):  
Robert C. Rau ◽  
Robert L. Ladd ◽  
John Moteff
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Threshold Region ◽  
Body Centered Cubic ◽  
Defect Clusters ◽  
Neutron Fluences ◽  
Transmission Electron ◽  
Abrupt Changes ◽  
The Matrix

As part of a program investigating the effects of neutron irradiation on the physical and mechanical properties of body centered cubic refractory metals, transmission electron microscopy has been carried out on irradiated tungsten after tensile and creep-rupture testing. These observations have shown the existence of a fluence threshold region between 5.9 × 1018 and 3.8 × 1019 nvt (E < 1 MeV) over which both microstructure and mechanical properties undergo abrupt changes.A series of specimens irradiated at pile ambient temperature (∼ 70°C) to various fast neutron fluences and subsequently tensile tested at 400°C showed dramatic evidence of the build-up of defect clusters with increasing exposure. The starting microstructure present in undeformed button heads of unirradiated control specimens consisted of large tungsten grains divided into many small subgrains by hexagonal dislocation networks, as shown in Figure 1. Irradiation to neutron fluences of 4.0 and 5.9 × 1018 nvt produced tiny dot clusters in the matrix, as shown in Figure 2.

Microstructural and Mechanical Properties of Polyester/Nanoclay Nanocomposites: Microstructure-Mixing Strategy Correlation

2011 ◽  
Vol 1312 ◽  
Author(s):  
Hamid Dalir ◽  
Rouhollah D. Farahani ◽  
Vireya Nhim ◽  
Benjamin Samson ◽  
Martin Lévesque ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Strain ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Roll Mill ◽  
The Matrix ◽  
Polyester Matrix ◽  
Excellent Improvement

ABSTRACTDifferent nanoclay mixing strategies using a three-roll mill and ultrasonication is proposed to obtain the desired polyester/nanoclay dispersion, intercalation, and exfoliation. The dispersion states of the modified nanoclay in polymer with 2, 4 and 6 wt% loading were characterized with X-ray diffraction, scanning electron microscopy (SEM), and low and high magnification transmission electron microscopy (TEM). The mechanical properties of the clay-reinforced polyester nanocomposites were a function of the nature and the content of the clay in the matrix. The nanocomposite containing 4 wt% modified Cloisite® 15A exhibits excellent improvement in modulus (by ~51%) and tensile strength (by ~12%) with a decrease in fracture strain (by ~26%) and fracture energy (by ~17%). These mechanical characteristic changes can be attributed to the dispersion, intercalation, and exfoliation of the nanoclays inside the polyester matrix.

scholarly journals Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 950
Author(s):  
Hongtao Cao ◽  
Beijun Liu ◽  
Yiwen Ye ◽  
Yunfang Liu ◽  
Peng Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
The Self ◽  
Reinforced Composites ◽  
Two Phase ◽  
Reinforced Composite ◽  
Transmission Electron ◽  
The Matrix ◽  
Ft Ir ◽  
The Cross

Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40–60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

scholarly journals The Influence of Heat Input on the Microstructure and Properties of Wire-Arc-Additive-Manufactured Al-Cu-Sn Alloy Deposits

Metals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 79
Author(s):  
Shuai Wang ◽  
Huimin Gu ◽  
Wei Wang ◽  
Chengde Li ◽  
Lingling Ren ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Grain Boundary ◽  
Heat Input ◽  
Raw Material ◽  
Layer Height ◽  
Transmission Electron ◽  
The Matrix ◽  
Wire Arc Additive Manufacturing ◽  
Scanning Electron

In this experiment, Al-Cu-Sn alloy was used as raw material to form deposits with different heat input using the wire-arc additive manufacturing (WAAM) process. The effects of heat input on microstructure and mechanical properties of Al-Cu-Sn alloy deposits were investigated by metallography, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and transmission electron microscopy (TEM) and mechanical properties tests. The results show that with increased of heat input, the thickness of the deposits increased and the layer height of the deposits increased. The number and size of pores in the deposits also improved with the increased heat input. The grain size of the deposits in the as-deposited state gradually increased and changed from isometric crystals to columnar crystals, the precipitated θ phases gradually converged on the grain boundary from within the grains. After T6 heat treatment, with increased heat input, the number of unsolved θ phases on the grain boundary increased, and the number of θ phases precipitated out of the matrix decreased as the phase spacing increased. With the increased heat input, the mechanical properties of the deposits gradually decreased, and the fracture mode changed from ductile fracture to brittle fracture.

Microstructure and Mechanical Properties of SiC/zirconia-toughened Mullite Nanocomposites Prepared from Mixtures of Mullite Gel, 2Y-TZP, and SiC Nanopowders

2002 ◽  
Vol 17 (5) ◽  
pp. 1024-1029 ◽  
Author(s):  
X. H. Jin ◽  
L. Gao ◽  
L. H. Gui ◽  
J. K. Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Grain Boundaries ◽  
Low Energy ◽  
Liquid Interfaces ◽  
Sic Nanoparticles ◽  
Transmission Electron ◽  
The Matrix

SiC/ZTM (zirconia-toughened mullite) nanocomposites were prepared by hot pressing mixtures of mullite gel, 2Y-TZP, and SiC nanopowders. The intimate mixing of Al2O3 and SiO2 components in the starting powder prevented intermediate ZrSiO4 phase formation during sintering. Addition of nano-sized SiC significantly retarded the matrix grain growth, making the microstructure much finer and more uniform. Transmission electron microscopy and high-resolution transmission electron microscopy revealed that many SiC nanoparticles were found in mullite and ZrO2 grains, and low-energy grain boundaries and mullite–liquid interfaces parallel to the {110} planes of rodlike mullite grains were formed. It is deduced that the formation of rodlike mullite grains is the result of the preferential development of these low-energy grain boundaries and mullite–liquid interfaces. The mechanical properties of the SiC/ZTM nanocomposite showed significant improvement over those of ZTM, and further enhancement in the mechanical properties was achieved by combinative strengthening with nano- and micro-sized SiC.

Phase Transformations in Ti-7w/oMo-3w/oMe Alloy

1974 ◽  
Vol 32 ◽  
pp. 514-515
Author(s):  
S. Fujishiro
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Mechanical Processing ◽  
Ray Method ◽  
X Ray ◽  
Transmission Electron ◽  
Water Quench ◽  
Alpha Beta

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.

Dynamics of Nanoparticle Chain Aggregates of Carbon Under Tension

2003 ◽  
Vol 778 ◽  
Author(s):  
Rajdip Bandyopadhyaya ◽  
Weizhi Rong ◽  
Yong J. Suh ◽  
Sheldon K. Friedlander
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Polymer Film ◽  
Elastic Behavior ◽  
Small Strains ◽  
Transmission Electron ◽  
Chain Aggregates ◽  
Nanoparticle Chains ◽  
Reinforcing Filler

AbstractCarbon black in the form of nanoparticle chains is used as a reinforcing filler in elastomers. However, the dynamics of the filler particles under tension and their role in the improvement of the mechanical properties of rubber are not well understood. We have studied experimentally the dynamics of isolated nanoparticle chain aggregates (NCAs) of carbon made by laser ablation, and also that of carbon black embedded in a polymer film. In situ studies of stretching and contraction of such chains in the transmission electron microscope (TEM) were conducted under different maximum values of strain. Stretching causes initially folded NCA to reorganize into a straight, taut configuration. Further stretching leads to either plastic deformation and breakage (at 37.4% strain) or to a partial elastic behavior of the chain at small strains (e.g. 2.3% strain). For all cases the chains were very flexible under tension. Similar reorientation and stretching was observed for carbon black chains embedded in a polymer film. Such flexible and elastic nature of NCAs point towards a possible mechanism of reinforcement of rubber by carbon black fillers.

Sign in / Sign up

Export Citation Format

Share Document