Effect of liquid butadiene rubber on mechanical properties of polyamide 11/polyamide 12 blends

2015 ◽  
Vol 35 (4) ◽  
pp. 349-357 ◽  
Author(s):  
Jan Simek ◽  
Veronika Dockalova ◽  
Zdenek Hrdlicka ◽  
Vratislav Duchacek
Keyword(s):  
Impact Strength ◽  
Molar Mass ◽  
Mechanical Analysis ◽  
Butadiene Rubber ◽  
Scanning Calorimetry ◽  
Polyamide 11 ◽  
Polyamide 12 ◽  
End Groups ◽  
The Impact ◽  
Ubbelohde Viscometer

Abstract Polyamide 11 (PA 11)/polyamide 12 (PA 12) blends with and without liquid polybutadiene (LB) containing isocyanate end groups (LBD) were prepared in the Brabender plastograph. The rubber was added in order to increase the impact strength of the polyamides. Tensile strength and elongation at the upper yield point and hardness were also measured. Thermal properties were determined by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Fourier transform infrared (FTIR) spectroscopy was used to determine functional groups of polyamides and to reveal possible reactions between the polyamides and LBD. Intrinsic viscosity, measured by an Ubbelohde viscometer, was used to calculate molar mass. The LB has been found as a useful modifier of impact strength.

Mechanical and thermal properties of polybutylene terephthalate/ethylene-vinyl acetate blends using vane extruder

e-Polymers ◽  
2018 ◽  
Vol 18 (1) ◽  
pp. 67-73 ◽  
Author(s):  
Cong Meng ◽  
Jin-ping Qu
Keyword(s):  
Impact Strength ◽  
Vinyl Acetate ◽  
Loss Modulus ◽  
Weight Fraction ◽  
Ethylene Vinyl Acetate ◽  
Mechanical Analysis ◽  
Mechanical And Thermal Properties ◽  
Polybutylene Terephthalate ◽  
Scanning Calorimetry ◽  
The Impact

AbstractThe poly(butylene terephthalate) (PBT)/ethylene-vinyl acetate copolymer (EVA) blends with different contents of EVA were prepared by an vane extruder. From the observation of morphologies, impact strength and dynamic mechanical analysis (DMA), the EVA particles were well dispersed in the PBT matrix and improved the impact strength of PBT. Differential scanning calorimetry measurements demonstrate that there is little diversification in the crystal structure and type. Thermogravimetric analysis reveals that as the weight fraction of EVA increases, the thermal stability of composite is enhanced. The rheological analyses indicate that the PBT/EVA blends follow a non-Newtonian behavior and viscosities of the blends are drastically lower than that of pure PBT at higher frequencies. The storage modulus (G′) and loss modulus (G″) of the blends monotonously increase as the frequency rises. This work provides a novel method to develop blends with excellent performance.

Mechanical properties and morphologies of polypropylene composites synergistically reinforced-toughened by styrene–butadiene rubber and graphene oxide nanosheets

2019 ◽  
Vol 33 (3) ◽  
pp. 413-431
Author(s):  
Zhengjun Wang ◽  
Yi Guo ◽  
Lei Yan ◽  
Jun Bian ◽  
Hongcai Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Impact Strength ◽  
Mechanical Analysis ◽  
Styrene Butadiene Rubber ◽  
Differential Scanning Calorimetric ◽  
Butadiene Rubber ◽  
Β Phase ◽  
Styrene Butadiene ◽  
The Impact

Chemically reduced graphene (C- rGO) nanosheets were first prepared from graphene oxide (GO), and then the polypropylene (PP) composites synergistically reinforced–toughened by styrene–butadiene rubber (SBR), and C- rGO nanosheets were fabricated via melt blending. The mechanical properties of PP can be considerably improved by synergistically filling with C- rGO nanosheets and SBR, especially for the notched Izod impact strength (IS). The results from the X-ray diffraction, polarizing optical micrographs, scanning electron microscope, differential scanning calorimetric, dynamic mechanical analysis, and thermogravimetric analysis measurements reveal that: (1) the β-phase crystal structure of the PP is formed when the C- rGO and SBR are synergistically filled with PP and its formation plays a role for the enhancement of the impact strength for PP/SBR/C- rGO composites; (2) the dispersion of the C- rGO and SBR in the PP/SBR/C- rGO composites is homogeneous, indicating that synergistic incorporating method decreases the aggregation of nanosheets and thus increases the sites for dissipation of shock for impact energy in the PP/SBR/C- rGO composites; and (3) the thermal analysis shows high thermal stability for the PP/SBR/C- rGO composites.

A novel recycled polyethylene terephthalate/polyamide 11 (rPET/PA11) thermoplastic blend

2021 ◽  
pp. 147776062110010
Author(s):  
Zahid Iqbal Khan ◽  
Zurina Binti Mohamad ◽  
Abdul Razak Bin Rahmat ◽  
Unsia Habib ◽  
Nur Amira Sahirah Binti Abdullah
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Practical Implication ◽  
Polyamide 11 ◽  
Recycled Polyethylene ◽  
Twin Screw ◽  
Electron Microscopy Analysis ◽  
The Impact

This work explores a novel blend of recycled polyethylene terephthalate/polyamide 11 (rPET/PA11). The blend of rPET/PA11 was introduced to enhance the mechanical properties of rPET at various ratios. The work’s main advantage was to utilize rPET in thermoplastic form for various applications. Three different ratios, i.e. 10, 20 and 30 wt.% of PA11 blend samples, were prepared using a twin-screw extruder and injection moulding machine. The mechanical properties were examined in terms of tensile, flexural and impact strength. The tensile strength of rPET was improved more than 50%, while the increase in tensile strain was observed 42.5% with the addition of 20 wt.% of PA11. The improved properties of the blend were also confirmed by the flexural strength of the blends. The flexural strength was increased from 27.9 MPa to 48 MPa with the addition of 30 wt.% PA11. The flexural strain of rPET was found to be 1.1%. However, with the addition of 10, 20 and 30 wt.% of PA11, the flexural strain was noticed as 1.7, 2.1, and 3.9% respectively. The impact strength of rPET/PA11 at 20 wt.% PA11 was upsurged from 110.53 to 147.12 J/m. Scanning electron microscopy analysis revealed a dispersed PA11 domain in a continuous rPET matrix morphology of the blends. This work practical implication would lead to utilization of rPET in automobile, packaging, and various industries.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

scholarly journals The Impact of Artificial Marble Wastes on Heat Deflection Temperature, Crystallization, and Impact Properties of Polybutylene Terephthalate

Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4242
Author(s):  
Tianliang Feng ◽  
Yangzhou Li ◽  
Liang Fang ◽  
Zhenming Chen
Keyword(s):  
Impact Strength ◽  
Resource Utilization ◽  
Melt Blending ◽  
X Ray Diffraction ◽  
Polybutylene Terephthalate ◽  
Scanning Calorimetry ◽  
Electron Microscope Analysis ◽  
Heat Deflection Temperature ◽  
The Impact ◽  
Temperature Crystallization

As artificial marble is abundant and widely used in residential and commercial fields, the resource utilization of artificial marble wastes (AMWs) has become extremely important in order to protect the environment. In this paper, polybutylene terephthalate/artificial marble wastes (PBT/AMWs) composites were prepared by melt blending to maximize resource utilization and increase PBT performance. The research results showed that the filling of AMWs was beneficial to the improvement of PBT-related performance. X-ray diffraction analysis results indicated that after filling AMWs into the PBT matrix, the crystal structure of PBT was not changed. Heat deflection temperature (HDT) analysis results indicated that the HDT of PBT composites with 20 wt% AMWs reached 66.68 °C, which was 9.12 °C higher than that of neat PBT. Differential scanning calorimetry analysis results showed that heterogeneous nucleation could be well achieved when the filling content was 15 wt%; impact and scanning electron microscope analysis results showed that due to the partial core-shell structure of the AMWs, the impact strength of PBT was significantly improved after filling. When the filling amount was 20 wt%, the impact strength of the PBT composites reached 23.20 kJ/m2, which was 17.94 kJ/m2 higher than that of neat PBT. This research will not only provide new insights into the efficient and high-value utilization of AMWs, but also provide a good reference for improved applications of other polymers.

scholarly journals PENGARUH PELARUT (ETIL BENZENA), PERBANDINGAN STYRENE BUTADIENE RUBBER (SBR) TERHADAP STIREN, DAN JUMLAH INISIATOR (BPO) PADA PEMBUATAN HIGH IMPACT POLYSTYRENE (HIPS)

2010 ◽  
Vol 2 (2) ◽  
Author(s):  
Dwi Wahyuni
Keyword(s):  
Impact Strength ◽  
High Heat ◽  
High Impact ◽  
Styrene Butadiene Rubber ◽  
Ethyl Benzene ◽  
Butadiene Rubber ◽  
High Impact Polystyrene ◽  
Aerospace Material ◽  
Styrene Butadiene ◽  
The Impact

High impact polystyrene (HIPS) is the widely used material now, and also for the aerospace material as a communication instrument system and an electrical insulation. In order to produce HIPS, there are a view method which can be executed. In this case, the research is executed by the copolymerization processes of styrene butadiene rubber (SBR) solution in styrene. Variables which influence to the result properties (HIPS) are the SBR to styrene ratio, the solvent (ethyl benzene), the benzoyl peroxide initiator (BPO). The properties of the product are tensile strength, impact strength, softening point, melting point and the hardness. The result showed that the properties of the HIPS product was near of the HIPS high heat. The optimal processes condition was the solvent to the styrene monomer ratio was 0.05492, the SBR to the styrene ratio was 0.1236 and the BPO to the styrene ratio was 0,0003. The properties of the HIPS product were: the impact strength was (519-1215) N per cm, the tensil strength not more than was 106 N per cm, the elongation was (36-54) percent and the hardness was (65-69) shore A. This properties achieved at the mixing polymerization processes 4 scale in 11-12 hours, the early mixing at 4 scale 1 hours, the cutting chain 2 drops.

Renewable resources-based PTT [poly(trimethylene terephthalate)]/switchgrass fiber composites: The effect of compatibilization

2012 ◽  
Vol 85 (3) ◽  
pp. 521-532 ◽  
Author(s):  
Jeevan Prasad Reddy ◽  
Manjusri Misra ◽  
Amar Mohanty
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Renewable Resources ◽  
Melt Flow Index ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Flow Index ◽  
Methylene Diphenyl Diisocyanate ◽  
Trimethylene Terephthalate ◽  
The Impact

In this research, switchgrass (SG) fiber-reinforced poly(trimethylene terephthalate) (PTT) biocomposites were prepared by extrusion followed by injection molding machine. The methylene-diphenyl-diisocyanate-polybutadiene (MDIPB) prepolymer was used to enhance the impact strength of the biocomposites. In addition, the polymeric methylene-diphenyl-diisocyanate (PMDI) compatibilizer was used to enhance the mechanical properties of the composites. The effect of compatibilizer on mechanical, crystallization melting, thermomechanical, melt flow index (MFI), morphological, and thermal stability properties of the composites was studied. Thermomechanical properties of the biocomposites were studied by dynamic mechanical analysis (DMA). Scanning electron microscopy (SEM) was used to observe the interfacial adhesion between the fiber and matrix. The results showed that MDIPB and PMDI have a significant effect on the mechanical properties of the composites. The impact strength of MDIPB- and PMDI-compatibilized composites was increased by 87 % when compared to the uncompatibilized composite.

scholarly journals The Effect of Crystallinity on the Toughness of Cast Polyamide 6 Rods with Different Diameters

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 293
Author(s):  
Miklós Odrobina ◽  
Tamás Deák ◽  
László Székely ◽  
Tamás Mankovits ◽  
Róbert Zsolt Keresztes ◽  
...  
Keyword(s):  
Impact Strength ◽  
Impact Test ◽  
Charpy Impact ◽  
Polyamide 6 ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Tensile Impact ◽  
Different Diameters ◽  
The Impact ◽  
The Degree Of Crystallinity

The present paper concentrates on the toughness and the degree of crystallinity of the magnesium-catalyzed polyamide 6 rods cast in different diametres, which are commonly used for gear manufacturing. Its toughness cannot be regarded as a constant feature due to the casting technology. The mechanical properties of the semi-finished products are sensitive to the manufactured dimension, e.g., cast diameter, which are investigated by the Charpy impact test and tensile impact test. It is generally accepted that the impact strength and tensile-impact strength correlate with the degree of crystallinity beside many other material’s feature. Crystallinity is evaluated by Differential Scanning Calorimetry. The aim of this study is to determine the relationship between toughness and crystallinity of the magnesium-catalyzed cast PA6 rods with different diameters. For the research cast rods between 40 and 300 mm diameter were selected in seven-dimensional steps. Based on the results, it was found that the toughness depends strongly on the diameter size. Furthermore, it is proved that the crystallinity explains 62.3% of the variation of the Charpy’s impact strengths, while the tensile impact method was not suitable to detect the difference between the test samples.

Structure-property relationship of biodegradable poly(butylene succinate)/polycaprolactone coated inorganic particle composites

2013 ◽  
Vol 33 (2) ◽  
pp. 111-119
Author(s):  
Yiming Liu ◽  
Qing Liu ◽  
Bing Meng ◽  
Zhihua Wu
Keyword(s):  
Impact Strength ◽  
High Speed ◽  
Complex Viscosity ◽  
Structure Property ◽  
Scanning Calorimetry ◽  
Butylene Succinate ◽  
Elongation At Break ◽  
Inorganic Particle ◽  
Biodegradable Poly ◽  
The Impact

Abstract Polycaprolactone (PCL)-coated micro kaolin and nano-titania were prepared by high-speed hybrid mechanical coating. Poly(butylene succinate) (PBS)-coated inorganic particle composites were prepared by the melt-blending process. The influence of coated kaolin microparticles on the dynamic rheological behavior, non-isothermal crystallization behavior, micromorphology, and mechanical behavior were investigated. The effect of coated nano-titania on the mechanical properties of PBS-coated kaolin composites was also studied. A dynamic rheological property indicates that the complex viscosity of PBS-coated kaolin microcomposites is higher than neat PBS. Differential scanning calorimetry (DSC) implies that the micrometric size of kaolin particles restrains the crystallization of PBS. Scanning electronic microscopy (SEM) reveals a well dispersed state of coated kaolin in the polymer matrix. The impact strength of PBS-coated kaolin microcomposites is improved, while the tensile strength and elongation at break is decreased, but still appreciable. The introduction of coated nano-titania improves the impact strength dramatically, and the elongation at break of composites is considerable.

HIGH-IMPACT PP NANOCOMPOSITES: INFLUENCE OF CLAY CONTENT ON MECHANICAL AND THERMAL PROPERTIES

2013 ◽  
Vol 12 (06) ◽  
pp. 1350039
Author(s):  
L. G. FURLAN ◽  
RICARDO V. B. OLIVEIRA ◽  
ANDRÉIA C. E. MELLO ◽  
SUSANA A. LIBERMAN ◽  
MAURO A. S. OVIEDO ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Clay Content ◽  
Mechanical Analysis ◽  
High Impact ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Izod Impact

The preparation of high-impact polypropylene nanocomposites with different organo-montmorillonite (O-MMT) contents by means of meltprocessing was investigated. The nanocomposite properties were evaluated by transmission electron microscopy (TEM), flexural modulus, izod impact strength, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was noticed that the PP/O-MMT nanocomposites properties were affected by clay content. Exceptional improvements in impact strength were obtained (maximum of 185%) by the use of low O-MMT content. The results showed that higher enhancement on mechanical/thermal properties was obtained by 3 wt.% of O-MMT instead of higher quantities.

Sign in / Sign up

Export Citation Format

Share Document