Effect of particle size on mechanical properties and tribological behaviour of aluminium/fly ash composites

2012 ◽  
Vol 19 (3) ◽  
pp. 247-253 ◽  
Author(s):  
Krishnan Ravi Kumar ◽  
Kothavady Mylsamy Mohanasundaram ◽  
Ganesan Arumaikkannu ◽  
Ramanathan Subramanian
Keyword(s):  
Tensile Strength ◽  
Wear Resistance ◽  
Fly Ash ◽  
Ultimate Tensile Strength ◽  
Coefficient Of Friction ◽  
Fine Particles ◽  
Dry Sliding Wear ◽  
Tribological Behaviour ◽  
Weight Percentage ◽  
Pin On Disc

AbstractIn the present study, aluminium alloy (A380) composites containing 3, 6, 9 and 12 weight percentage of fly ash particles were fabricated by liquid metallurgy technique. Three different size ranges of fly ash particles (50–75 μm, 75–103 μm and 103–150 μm) were used. The composites were evaluated for hardness, tensile strength, density, dry sliding wear and frictional behaviour. Pin-on disc apparatus was used to conduct wear tests at loads of 20, 30 and 40 N at a sliding speed of 3 m/s for a constant period of 10 min. Results showed that hardness, ultimate tensile strength, wear resistance and coefficient of friction were superior in composites reinforced with coarse fly ash particles (103–150 μm) compared to composites with fine particles. The hardness, ultimate tensile strength and wear resistance increased, whereas the coefficient of friction and density decreased with the increase in weight percentage of fly ash. Wear resistance and coefficient of friction decreased with increase in applied load. Scanning electron microscope investigations of worn-out samples were carried out to study the progress of wear.

scholarly journals Wear Behaviour of Eutectic Al-Si Alloy-Graphite Composites Fabricated by Combined Modified Two-Stage Stir Casting and Squeeze Casting Methods

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
P. Shanmughasundaram ◽  
R. Subramanian
Keyword(s):  
Wear Resistance ◽  
Wear Test ◽  
Stir Casting ◽  
Constant Load ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Sliding Velocity ◽  
Weight Percentage ◽  
Pin On Disc ◽  
Graphite Composites

Dry sliding wear behaviour of eutectic Al-Si alloy-graphite composites was investigated employing a pin-on-disc wear test rig. Results revealed that the wear and friction coefficients decreased linearly with increasing weight percentage of graphite particles. Wear resistance of the composite increased considerably with increasing sliding velocity at constant load. In contrast, the friction coefficient of Al-7.5 wt.% Gr composite increased when the sliding velocity was increased from 1 m/s to 2 m/s at 49 N. Worn-out surfaces of wear specimens after the test were examined by scanning electron microscopy to study the morphology of worn surfaces. EDS analysis was carried out to investigate the influence of mechanically mixed layer (MML) which comprises oxides and iron, and this acted as an effective tribolayer in enhancing the wear resistance at higher sliding velocity.

TOUGHMET 2CX

Alloy Digest ◽  
2013 ◽  
Vol 62 (6) ◽  
Keyword(s):  
Tensile Strength ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Coefficient Of Friction ◽  
Loading Conditions ◽  
Severe Loading

Abstract ToughMet 2 CX is a Cu-9Ni-6Sn alloy that combines low coefficient of friction with wear resistance. ToughMet alloys are a line of spinodal hardened Cu-Ni antigalling alloys for bearings capable of performing with a variety of shafting materials and lubricants. The alloys combine a high lubricity with wear resistance in these severe loading conditions. ToughMet 2CX in the cast and spinodally hardened (CX) condition exhibits tensile strength in excess of 724 MPa (105 ksi) and hardness exceeding HRC 27 with excellent machinability. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming. Filing Code: Cu-819. Producer or source: Materion Brush Performance Alloys.

Improving Wear Resistance of AISI 316LN Austenitic Stainless Steel Using Friction Stir Processing

2015 ◽  
Vol 787 ◽  
pp. 421-425
Author(s):  
A. Vignesh ◽  
V.G. Vijay Prakaash ◽  
A.K. Lakshminarayanan
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Austenitic Stainless Steel ◽  
Friction Stir Processing ◽  
Sliding Wear ◽  
Dry Sliding Wear ◽  
Friction Stir ◽  
Pin On Disc ◽  
Metal Microstructure ◽  
Equiaxed Grains

An attempt is made to modify the surface metallurgically and enhance the wear resistance of AISI 316LN austenitic stainless steel using friction stir processing. Friction stir welding tools made up of tungsten based alloy with pin and pinless configuration was used. Fine equiaxed grains were observed in the friction stir processed zone irrespective of tool configuration used. Dry sliding wear resistance was evaluated using pin-on-disc wear tester and it is found that, the friction stir processed zone showed superior wear resistance compared to the base metal. Microstructure, micro hardness, and worn surfaces were used to correlate the results obtained.

An Experimental Investigation on Mechanical and Wear Properties of Al7075/SiCp Composites: Effect of SiC Content and Particle Size

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Thella Babu Rao
Keyword(s):  
Particle Size ◽  
Tensile Strength ◽  
Wear Resistance ◽  
Ultimate Tensile Strength ◽  
Matrix Material ◽  
Mechanical Tests ◽  
Experimental Investigations ◽  
Wear Properties ◽  
Sic Particles ◽  
Sic Particle

One of the major advantages of metal matrix composites (MMCs) is that their tailorable properties meet the specific requirements of a particular application. This paper deals with the experimental investigations done on the effects of the reinforcement particulate size and content on the Al7075/SiC composite. The composites were manufactured using stir casting technique. The effect of SiC particle size (25, 50, and 75 μm) and particulate content (5, 10, and 15 wt %) on the microstructural, mechanical properties, and wear rate of the composites was studied and the results were analyzed for varied conditions of reinforcement. Scanning electron microscope (SEM) examinations were used to assess the dispersion of SiC particles reinforced into the matrix alloy and was found with reasonably uniform with minimal particle agglomerations and with good interfacial bonding between the particles and matrix material. X-ray diffraction (XRD) analysis confirmed the presence of Al and SiC with the composite. The results of mechanical tests showed that the increasing SiC particle size and content considerably enhanced the ultimate tensile strength and hardness of the composites while the ductility at this condition was decreased. The highest ultimate tensile strength of 310 MPa and hardness of 126 BHN were observed for the composites containing 15 wt %. SiC at 75 μm. Lesser the wear resistance of the reference alloy while it was enhanced up to 40% with the composites. The wear resistance was increased up to 1200 m of sliding distance for all the composites, whereas for the composite containing 75 μm SiC particles, it was extended up to 1800 m.

scholarly journals Development of High Performance (Mechanical and Wear Properties) of AA 6061-Hybrid Nano Composites Via Liquid Metallurgy Route

2019 ◽  
Vol 22 (2) ◽  
pp. 143-150
Author(s):  
Hussain J. M. Al-Alkawi ◽  
Abduljabbar Owaid Hanfesh ◽  
Saja Mohammed Noori Mohammed Rauof
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Wear Rate ◽  
Yield Strength ◽  
Base Metal ◽  
Young Modulus ◽  
Nano Particles ◽  
Wear Properties ◽  
Constant Weight ◽  
Weight Percentage

This research is devoted to study the influence of different weight percent concerning to the additions of Ti and Cu on mechanical and tribological properties of AA6061. The composite materials consist of different weight percentage of Ti (0.2, 0.4, and 0.6) wt% and constant weight percentage of Cu (0.2) wt% which were fabricated by liquid metallurgy route technique. Microstructural characterization and phases have been examined by using SEM (scanning electron microscopic).SEM examination showed uniform distribution of nano Ti and Cu in AA6061. The consequences of mechanical tests demonstrated clear enhancement in mechanical properties, such as ultimate tensile strength, yield strength, young modulus, ductility% and hardness at additive percentage of 0.4% Ti+0.2%Cu nano particles incorporated into molten AA6061. Percentage of enhancement ultimate tensile strength is about 73.3%, yield strength about 82.7%, young modulus is about 21.2%, the  Vickers hardness about 42.6% and the decreasing in ductility was about 25.2% compared with the metal matrix (AA6061). The wear rate test was performed by using pin on disc rig for both hybrid nano composite and base metal (AA6061) under various loads (10,15and 20) N with sliding speed (1.282) m/sec at a (10) min’s time. The results showed a decrease in wear rate at 0.4%Ti+0.2%Cu compared with the base metal (AA6061). Improvement percentage of wear rate is about 105% at 20 N load.

Process optimization using grey relational analysis in dry sliding wear behavior on SiC/B4C/Talc reinforced Al 6061 hybrid metal matrix composite

2021 ◽  
Vol 118 (6) ◽  
pp. 614
Author(s):  
Chellamuthu Ramesh Kumar ◽  
Subramanian Baskar ◽  
Ganesan Ramesh ◽  
Pathinettampadian Gurusamy ◽  
Thirupathy Maridurai
Keyword(s):  
Wear Resistance ◽  
Metal Matrix ◽  
Wear Behavior ◽  
Base Alloy ◽  
Specific Weight ◽  
Dry Sliding Wear ◽  
Wear Properties ◽  
Weight Percentage ◽  
Casting Technique ◽  
Grey Relational

In this research, investigations were carried out on Al6061 base alloy with the changing weight percentage of silicon carbide (SiC) and boron carbide (B4C) with keeping the amount of talc constant. The main objective of this present study was to improve the wear resistance of aluminum alloy using SiC/B4C/talc ceramic particles using stir-casting technique and how the eco-friendly talc content influencing the solid lubricity during the abrasion process. The experiments were conducted via orthogonal array of L27 using Taguchi’s method. The optimum value along with the coefficient of friction was obtained on the basis of grey relational equations and ANOVA, which helped in analysis of most influential input parameters such as applied load, sliding speed, sliding distance and percentage of reinforcement. Conformation tests were performed for the purpose of validation of the experimental results. The specimens were analyzed using scanning electron microscope (SEM) with EDX for micro structural studies. The SiC, B4C and talc presence in the composite helped to improve the mechanical properties, according to the results. The presence of solid lubricant talc as reinforcement to the aluminum hybrid composite reduced the wear properties and decreased the co-efficient friction. These wear resistance improved aluminum metal matrix composites could be used in automobile, defense and domestic applications where high strength and wear resistance required with lesser specific weight.

Effect of abrasive particle size on tribological behavior of elastomers

2019 ◽  
Vol 234 (3) ◽  
pp. 373-385 ◽  
Author(s):  
F Hakami ◽  
A Pramanik ◽  
AK Basak ◽  
N Ridgway ◽  
MN Islam
Keyword(s):  
Particle Size ◽  
Tensile Strength ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Abrasive Particle ◽  
Tribological Behaviour ◽  
Elongation At Break ◽  
Tear Strength ◽  
Wear And Friction ◽  
Abrasive Size

Effect of abrasive particle size on tribological behaviour of different elastomers was investigated experimentally in this study. The size of abrasive particle size was varied from coarse (425 µm) to fine (82 µm). Wear rate and coefficient of friction were calculated and analyzed accordingly followed by the examination of worn surfaces by a scanning electron microscope to unravel the wear mechanism. Experimental results showed that abrasive size had a significant effect on wear and friction behaviour of the elastomers. As the abrasive particle size increased, wear rate and coefficient of friction also increased at different rates and exhibited different wear mechanisms that changed from friction to fatigue and roll formation. Mechanical properties of elastomers such as hardness, tensile strength, tear strength, and elongation at break also contributed to wear and friction. The effect of elongation at break and tensile strength on wear rate is more pronounced at lower abrasive particle size, whereas hardness and tear strength play a pivotal role at the higher abrasive size.

Improving the Wear Resistance of Aluminum Fly Ash Composites by Multipass Friction Stir Processing

2015 ◽  
Vol 642 ◽  
pp. 55-59 ◽  
Author(s):  
Shueiwan Henry Juang ◽  
Liang Jing Fan ◽  
Hsu Shuo Chang
Keyword(s):  
Wear Resistance ◽  
Fly Ash ◽  
Friction Stir Processing ◽  
Sliding Wear ◽  
Normal Load ◽  
Aluminum Matrix ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Rates ◽  
Friction Stir

In this study, the multi-pass friction stir processing (MP-FSP) technique was performed on ADC6 aluminum alloy + 5 wt% fly ash composite (A5FC) castings to increase their surface area. The dry sliding wear behaviors of the ADC6 alloy, A5FCs, and MP-FSPed A5FCs were evaluated. Dry sliding wear tests were performed using a ring-on-washer machine at a constant rotation speed of 100 rpm for 60 min, and the normal load was 10, 20, 30, and 40 N. The results showed that the MP-FSPed A5FCs had the lowest wear rates in the load range from 10 to 40 N, and adhesive wear was the major wear mechanism in these tests. The increased wear resistance was mainly due to grain refinement and elimination of casting defects after subjecting the ash composite to MP-FSP. The microstructure of the MP-FSPed A5FCs reveals that the sizes of the added raw fly ash particles decreased from micro-to nanoscale levels, and the nanoscale fly ash was uniformly dispersed in the aluminum matrix.

Tribological behaviour of A390/Grp metal—matrix composites fabricated using a combination of rheocasting and squeeze casting techniques

2008 ◽  
Vol 222 (2) ◽  
pp. 257-265 ◽  
Author(s):  
T S Mahmoud
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Squeeze Casting ◽  
Dry Sliding Wear ◽  
Matrix Composites ◽  
Tribological Behaviour ◽  
Wear Performance ◽  
The Coefficient Of Friction ◽  
Steel Disc ◽  
A390 Alloy

The dry sliding wear performance of hypereutectic A390 Al—Si alloy reinforced with graphite particulates (Grp) was investigated. Composites containing 4 and 8 wt% of Grp were produced by rheocasting technique followed by squeeze casting. Pins of the materials were rubbed against a 316 stainless steel disc using pin-on-ring type apparatus under various loads and speeds. It has been observed that both wear rate and the coefficient of friction of the composites decreased considerably with Grp additions. The A390/Grp composites exhibited higher wear resistance than those obtained for the monolithic A390 alloy. The formation of the hard tribo-layer on the surface of the composites assisted in increasing the wear resistance of these materials. It is believed that the reduction of the friction coefficient is attributed the presence of the graphite layers within the tribo-layer.

Sign in / Sign up

Export Citation Format

Share Document