scholarly journals Oblique penetration mechanism of hybrid composite laminates

2021 ◽  
Vol 28 (1) ◽  
pp. 568-578
Author(s):  
Meng Han ◽  
Chuwei Zhou ◽  
Vadim V. Silberschmidt ◽  
Xindong Ma ◽  
Mao Liu ◽  
...  
Keyword(s):  
Composite Laminates ◽  
Hybrid Composites ◽  
High Strength ◽  
Oblique Impact ◽  
Contact Forces ◽  
Dissipation Energy ◽  
Penetration Mechanism ◽  
Oblique Impacts ◽  
Viscoelastic Constitutive Model ◽  
Short Time

Abstract Hybrid fiber composites are widely used to improve the anti-penetration performance. Carbon/Kevlar hybrid composites are used in aircrafts and safety devices, thanks to the strong toughness of Kevlar fibers and high strength of carbon fibers. In the present work, the contact force of hybrid composites under oblique impact is derived. The viscoelastic constitutive model of Kevlar layer is investigated and the dissipation energies of composites for different high velocity oblique impacts are simulated. The results show that hybrid composites have good bullet-proof performance, the contact forces are fluctuant in short time and the frictional dissipation energy allows us to prevent penetration.

scholarly journals Study on Burr Formation and Tool Wear in Drilling CFRP and Its Hybrid Composites

2021 ◽  
Vol 11 (1) ◽  
pp. 384
Author(s):  
Jeong Hwan Lee ◽  
Jun Cong Ge ◽  
Jun Hee Song
Keyword(s):  
Tool Wear ◽  
Composite Laminates ◽  
Hybrid Composites ◽  
Weight Ratio ◽  
High Strength ◽  
Operating Conditions ◽  
Fiber Reinforced Polymer ◽  
Burr Formation ◽  
Fiber Reinforced ◽  
Reinforced Polymer

As contemporary emerging materials, fiber-reinforced plastics/polymers (FRP) are widely used in aerospace automotive industries and in other fields due to their high strength-to-weight ratio, high stiffness-to-weight ratio, high corrosion resistance, low thermal expansion and other properties. Drilling is the most frequently used process in industrial operation for polymer composite laminates, owing to the need for joining structures. However, it is a great challenge for operators to drill holes in FRP materials, due to the non-homogenous and anisotropic properties of fibers. Various damages, such as delamination, hole shrinkage, and burr and tool wear, occur due to the heterogeneous and anisotropic nature of composite laminates. Therefore, in this study, carbon fiber reinforced polymer (CFRP)/aramid fiber reinforced polymer (AFRP) hybrid composites (C-AFRP) were successfully synthesized, and their drilling characteristics, including burr generation and tool wear, were also mainly investigated. The drilling characteristics of CFRP and C-AFRP were compared and analyzed for the first time under the same operating conditions (cutting tool, spindle speed, feed rate). The experimental results demonstrated that C-AFRP had higher tensile strength and good drilling characteristics (low thrust and less tool wear) compared with CFRP. As a lightweight and high-strength structural material, C-AFRP hybrid composites have great potential applications in the automobile and aerospace industries after the slight processing of burrs generated during drilling.

JESSOP JS17Cr-4Ni

Alloy Digest ◽  
1982 ◽  
Vol 31 (7) ◽  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Food Processing ◽  
Precipitation Hardening ◽  
High Strength ◽  
Heat Treating ◽  
Steel Company ◽  
Lower Strength ◽  
Nickel Copper ◽  
Short Time

Abstract JESSOP JS17Cr-4Ni is a martensitic, precipitation-hardening chromium-nickel-copper stainless steel. It provides an excellent combination of high strength and hardness, short-time low-temperature precipitation hardening and good mechanical properties at temperatures up to 600 F (316 C). Its corrosion resistance is quite good but inferior to lower strength grades produced for corrosion-resistance applications. JS17Cr-4Ni is used widely for critical applications in the aerospace, chemical, food processing and other industries. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-412. Producer or source: Jessop Steel Company.

scholarly journals Experimental Investigation on the Influence of Fiber Path Curvature on the Mechanical Properties of Composites

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2602
Author(s):  
Huaqiao Wang ◽  
Jihong Chen ◽  
Zhichao Fan ◽  
Jun Xiao ◽  
Xianfeng Wang
Keyword(s):  
Tensile Strength ◽  
Path Planning ◽  
Composite Laminates ◽  
Bending Strength ◽  
High Strength ◽  
Bending Test ◽  
Fiber Placement ◽  
Automated Fiber Placement ◽  
Fiber Path ◽  
Path Curvature

Automated fiber placement (AFP) has been widely used as an advanced manufacturing technology for large and complex composite parts and the trajectory planning of the laying path is the primary task of AFP technology. Proposed in this paper is an experimental study on the effect of several different path planning placements on the mechanical behavior of laminated materials. The prepreg selected for the experiment was high-strength toughened epoxy resin T300 carbon fiber prepreg UH3033-150. The composite laminates with variable angles were prepared by an eight-tow seven-axis linkage laying machine. After the curing process, the composite laminates were conducted by tensile and bending test separately. The test results show that there exists an optimal planning path among these for which the tensile strength of the laminated specimens decreases slightly by only 3.889%, while the bending strength increases greatly by 16.68%. It can be found that for the specific planning path placement, the bending strength of the composite laminates is significantly improved regardless of the little difference in tensile strength, which shows the importance of path planning and this may be used as a guideline for future AFP process.

scholarly journals Enhanced Water Resistance of Recycled Newspaper/High Density Polyethylene Composite Laminates via Hydrophobic Modification of Newspaper Laminas

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 421
Author(s):  
Binwei Zheng ◽  
Weiwei Zhang ◽  
Litao Guan ◽  
Jin Gu ◽  
Dengyun Tu ◽  
...  
Keyword(s):  
Stearic Acid ◽  
Photoelectron Spectroscopy ◽  
Composite Laminates ◽  
High Density Polyethylene ◽  
Water Resistance ◽  
Laminated Composite ◽  
High Strength ◽  
High Water ◽  
High Density ◽  
X Ray

A high strength recycled newspaper (NP)/high density polyethylene (HDPE) laminated composite was developed using NP laminas as reinforcement and HDPE film as matrix. Herein, NP fiber was modified with stearic acid (SA) to enhance the water resistance of the NP laminas and NP/HDPE composite. The effects of heat treatment and SA concentration on the water resistance and tensile property of NP and composite samples were investigated. The chemical structure of the NP was characterized with X-ray diffractometer, X-ray photoelectron spectroscopy and attenuated total reflectance Fourier transform infrared spectra techniques. The surface and microstructure of the NP sheets were observed by scanning electron microscopy. An expected high-water resistance of NP sheets was achieved due to a chemical bonding that low surface energy SA were grafted onto the modified NP fibers. Results showed that the hydrophobicity of NP increased with increasing the stearic acid concentration. The water resistance of the composite laminates was depended on the hydrophobicity of the NP sheets. The lowest value of 2 h water absorption rate (3.3% ± 0.3%) and thickness swelling rate (2.2% ± 0.4%) of composite were obtained when the SA concentration was 0.15 M. In addition, the introduction of SA can not only enhance the water resistance of the composite laminates, but also reduce the loss of tensile strength in wet conditions, which shows potential in outdoor applications.

Effect of Reinforcement and Tribological Behaviour of AA 7068 Hybrid Composites Manufactured through Powder Metallurgy Techniques

2017 ◽  
Vol 867 ◽  
pp. 19-28 ◽  
Author(s):  
J. Lakshmipathy ◽  
Subburaj Rajesh Kannan ◽  
K. Manisekar ◽  
S. Vinoth Kumar
Keyword(s):  
Sintering Temperature ◽  
Hybrid Composites ◽  
High Strength ◽  
Phase Changes ◽  
Wear Loss ◽  
X Ray Diffraction ◽  
Tribological Behaviour ◽  
Different Temperatures ◽  
Pin On Disc ◽  
Sliding Distance

In this article, an attempt was made to study the mechanical behaviour of AA7068 - 6 vol. % of MoS2 - X vol. % of WC (X = 0, 5, 10 and 15) hybrid aluminium composites produced by blend–press–sinter methodology. Compacted Powders (700MPa) were sintered at different temperatures (450 0c, 500 0c and 550 0c ) in order to find the influence of sintering temperature on mechanical properties and tribological behavior of AA7068 hybrid composites.The sintered samples have been characterized by x-ray diffraction (XRD) method for identification of phases and also to investigate the phase changes. The change in density, hardness and porosity values of composites were reported. The composite with 15 vol. % of tungsten carbide and 6 vol. % of MoS2 showed the highest hardness and density at the sintering temperature range of 550 0c. Pin-on-disc type apparatus was used for determining the wear loss occurring at different conditions. The hybridization of the two reinforcements enhanced the wear resistance of the composites, especially under high applied load, sliding distance and sliding speeds. Due to this, the hybrid aluminium composites can be considered as an outstanding material where high strength and wear-resistant components are of major importance, predominantly in the aerospace and automotive engineering sectors. The morphology of the wear debris and the worn out surfaces were analyzed to understand the wear mechanisms.

Flexural Response of Inorganic Hybrid Composites With E-Glass and Carbon Fibers

2010 ◽  
Vol 132 (2) ◽  
Author(s):  
James W. Giancaspro ◽  
Christos G. Papakonstantinou ◽  
P. N. Balaguru
Keyword(s):  
Carbon Fibers ◽  
Hybrid Composite ◽  
Composite Laminates ◽  
Hybrid Composites ◽  
Glass Fibers ◽  
Composite Plates ◽  
Carbon Composite ◽  
Primary Objective ◽  
Flexural Capacity ◽  
Compression Failure

By far, carbon and glass fibers are the most popular fiber reinforcements for composites. Traditional carbon composites are relatively expensive since the manufacturing process requires significant heat and pressure, while the carbon fibers themselves are inherently expensive to produce. In addition, they are often flammable and their use is restricted when fire is a critical design parameter. Glass fabrics are approximately one order of magnitude less expensive than similar carbon fabrics. However, they lack the stiffness and the durability needed for many high performance applications. By combining these two types of fibers, hybrid composites can be fabricated that are strong, yet relatively inexpensive to produce. The primary objective of this study was to experimentally investigate the effects of bonding high strength carbon fibers to E-glass composite cores using a high temperature, inorganic matrix known as geopolymer. Carbon fibers were bonded to E-glass cores (i) on only the tension face, (ii) on both the tension and compression faces, or (iii) dispersed throughout the core in alternating layers to obtain a strong, yet economical, hybrid composite laminate. For each response measured (flexural capacity, stiffness, and ductility), at least one hybrid configuration displayed mechanical properties comparable to all carbon composite laminates. The results indicate that hybrid composite plates manufactured using 3k unidirectional carbon tape exhibit increases in flexural capacity of approximately 700% over those manufactured using E-glass fibers alone. In general, as the relative amount of carbon fibers increased, the likelihood of precipitating a compression failure also increased. For 92% of the specimens tested, the threshold for obtaining a compression failure was utilizing 30% carbon fibers. The results presented herein can dictate future studies to optimize hybrid performance and to achieve economical configurations for a given set of design requirements.

Cutting Characteristics of Titanium Graphite Composite by Wire Electrical Discharge Machining

2012 ◽  
Vol 630 ◽  
pp. 114-120 ◽  
Author(s):  
Mamidala Ramulu ◽  
Mathew Spaulding ◽  
P. Laxminarayana
Keyword(s):  
Composite Laminates ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Hybrid Composites ◽  
Removal Rate ◽  
Wire Electrical Discharge Machining ◽  
Metal Composite ◽  
Workpiece Material ◽  
Graphite Composite ◽  
Wedm Process

To improve strength to weight ratios, the fiber reinforced polymer composite materials are often used in conjunction with another material, like metals, to form hybrid structure. This paper reports the feasibility of using wire electrical discharge machining (WEDM) for cutting Titanium/Graphite Hybrid Composites (TiGr). Slit and slot cuts with WEDM process has been performed. Cutting times and process parameters were recorded, and cut surface characteristics were evaluated both with an optical and scanning electron microscopy (SEM). The results in terms of cutting time, workpiece material removal rate, and damage were presented and discussed. It was found that use of WEDM is possible for machining advanced hybrid metal composite laminates with appropriate machine settings.

Oblique Impact Simulations of High Strength Agglomerates

2008 ◽  
pp. 243-253
Author(s):  
M. Khanal ◽  
W. Schubert ◽  
J. Tomas
Keyword(s):  
High Strength ◽  
Oblique Impact ◽  
Impact Simulations
Sign in / Sign up

Export Citation Format

Share Document