scholarly journals IMPACT OF USING PHOTOVOLTAIC PANELS IN PIGGERY ON GREENHOUSE GASES EMISSION

Author(s):  
Wojciech RZEŹNIK ◽  
Ilona RZEŹNIK ◽  
Paulina MIELCAREK

Farm buildings have a large number of unused roofs, where photovoltaic panels may be installed without limiting the agricultural land. In piggeries the largest demand for electricity has the ventilation system. The daily distribution of electricity demand is correlated to the diurnal variation of solar radiation. This allows immediate use the energy produced by photovoltaic panels. The aim of the study was to determine the energy demand of the ventilation system, to design a photovoltaic system for its operation and to determine the CO2 emission reduction. The research was carried out for the deep-litter piggery located in Poland. The demand for electricity was determined on the basis of three-year measurements of electricity consumption in the studied piggery. The photovoltaic system was designed to power the ventilation system. Mean annual demand was 26046 kWh. The designed PV system has power of 27 kWp (23984 kWh yr-1). Energy deficits (4591 kWh·yr-1) were noted for 8 months, and energy surpluses (2528 kWh·yr-1) for 4 months in a year. The reduction of CO2 emissions resulting from the use of a photovoltaic system to supply the ventilation system is 19.1 Mg CO2·yr-1 and represents 3% of the total greenhouse gases emissions from the piggery, expressed in CO2 equivalent. It may increase to 8.6% in case of installing the maximum number of PV panels system (maximum power of 78 kWp; total energy production 68526 kWh yr-1) on the southern part of the roof, but it requires the financial support for renewable energy by the government.

2018 ◽  
Vol 49 ◽  
pp. 00013 ◽  
Author(s):  
Bartosz Chwieduk ◽  
Michał Chwieduk

The paper presents the results of calculations of energy consumption and economic analysis of the operation of micro photovoltaic installations. Calculations have been made for a single-family house with an energy demand based on real electricity consumption. Two cases have been considered. In the first one, the photovoltaic system contains only PV modules and an inverter. Energy produced is sent to the power grid. In the second case, the PV system also contains batteries. Because of existing regulation conditions, it is better to accumulate produced energy than to sell it to the grid. Costs of construction of the PV systems and money savings during operation of the PV systems have been compared. Conclusions of profitability of analyzed systems have been presented.


2018 ◽  
Vol 19 (4) ◽  
pp. 790-816 ◽  
Author(s):  
Paula Fonseca ◽  
Pedro Moura ◽  
Humberto Jorge ◽  
Aníbal de Almeida

Purpose The purpose of this study was to design a renovation plan for a university campus building (Department of Electrical and Computer Engineering) with the aim to achieve nearly zero energy performance, ensuring a low specific demand (lower than 44 kWh/m2) and a high level of on-site renewable generation (equivalent to more than 20 per cent of the energy demand). Design/methodology/approach The baseline demand was characterized based on energy audits, on smart metering data and on the existing building management system data, showing a recent reduction of the electricity demand owing to some implemented measures. The renovation plan was then designed with two main measures, the total replacement of the actual lighting by LEDs and the installation of a photovoltaic system (PV) with 78.8 kWp coupled with an energy storage system with 100 kWh of lithium-ion batteries. Findings The designed renovation achieved energy savings of 20 per cent, with 27.5 per cent of the consumed energy supplied by the PV system. This will ensure a reduction of the specific energy of the building to only 30 kWh/m2, with 42.4 per cent savings on the net-energy demand. Practical implications The designed renovation proves that it is possible to achieve nearly zero energy goals with cost-effective solutions, presenting the lighting renovation and the solar PV generation system a payback of 2.3 and 6.9 years, respectively. Originality/value This study innovated by defining ambitious goals to achieve nearly zero energy levels and presenting a design based on a comprehensive lighting retrofit and PV generation, whereas other studies are mostly based on envelope refurbishment and behaviour changes.


Author(s):  
Mohamad Kharseh ◽  
Holger Wallbaum

The current work investigates how adding a battery of optimal capacity to a grid-connected photovoltaic (PV) system can improve its economic feasibility. Also, the effect of different parameters on the feasibility of the PV system was evaluated. The OBC was determined for different saving targets of the annual electricity consumption of the chosen building. For this aim, real electricity consumption data of a residential building in Landskrona, Sweden, was used as energy consumption profile. Solar World SW325XL, which is a monocrystalline solar panel, was selected as PV panels. The calculations were performed under the metrological and economic conditions of southern Sweden. Different working parameters (WP)were considered (prices of the battery, feed-in tariffs, and saving targets). The performed calculations show that the optimal battery capacity (OBC), in which the payback time (PBT) of the system is maximized, strongly depends on the WP. The proper selection of the battery can considerably increase the economic feasibility of the PV system in southern Sweden. However, in some cases, using battery can have a negative impact on the PBT of the system. The results show that the electricity price, the module price, the inverter price, and the inverter lifetime have the highest effect on the PBT.


TECCIENCIA ◽  
2021 ◽  
Vol 16 (31) ◽  
pp. 15-28
Author(s):  
Asad A. Naqvi ◽  
Talha Bin Nadeem ◽  
Ahsan Ahmed ◽  
Asad Ali Zaidi

Off-grid Photovoltaic (PV) system along with battery storage is very effective solution for electrification in remote areas. However, battery capacity selection is the most challenging task in system designing. In this study, an off-grid PV system along with battery storage is designed for the remote area of Karachi, Pakistan. The system is designed by considering the maximum energy requirement in summer season. The battery storage is selected to fulfill the energy demand during the night and cloudy seasons. On the basis of load, a total of 6 kW system is required to fulfill the energy demand. For such system, 925 Ah of battery is required to meet the energy requirement for a day in absence of solar irradiation. A regression-based correlation between battery capacity and energy demand is prepared for suitable battery sizing using Minitab. An economic analysis of the project is also carried out from which a net present value and simple payback are determined as USD 10,348 and 3 years, respectively. The environmental benefits are also been determined. It is found that the system will reduce around 7.32 tons of CO2 per annum which corresponds to the 183.69 tons of CO2 not produced in the entire project life.


Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1118 ◽  
Author(s):  
Thomas Kemmler ◽  
Bernd Thomas

Heat pumps in combination with a photovoltaic system are a very promising option for the transformation of the energy system. By using such a system for coupling the electricity and heat sectors, buildings can be heated sustainably and with low greenhouse gas emissions. This paper reveals a method for dimensioning a suitable system of heat pump and photovoltaics (PV) for residential buildings in order to achieve a high level of (photovoltaic) PV self-consumption. This is accomplished by utilizing a thermal energy storage (TES) for shifting the operation of the heat pump to times of high PV power production by an intelligent control algorithm, which yields a high portion of PV power directly utilized by the heat pump. In order to cover the existing set of building infrastructure, 4 reference buildings with different years of construction are introduced for both single- and multi-family residential buildings. By this means, older buildings with radiator heating as well as new buildings with floor heating systems are included. The simulations for evaluating the performance of a heat pump/PV system controlled by the novel algorithm for each type of building were carried out in MATLAB-Simulink® 2017a. The results show that 25.3% up to 41.0% of the buildings’ electricity consumption including the heat pump can be covered directly from the PV-installation per year. Evidently, the characteristics of the heating system significantly influence the results: new buildings with floor heating and low supply temperatures yield a higher level of PV self-consumption due to a higher efficiency of the heat pump compared to buildings with radiator heating and higher supply temperatures. In addition, the effect of adding a battery to the system was studied for two building types. It will be shown that the degree of PV self-consumption increases in case a battery is present. However, due to the high investment costs of batteries, they do not pay off within a reasonable period.


Electronics ◽  
2019 ◽  
Vol 8 (2) ◽  
pp. 149 ◽  
Author(s):  
Henrik Zsiborács ◽  
Nóra Hegedűsné Baranyai ◽  
Szilvia Csányi ◽  
András Vincze ◽  
Gábor Pintér

The energy demand of mankind is constantly growing, thus the utilization of various renewable energy sources, which also reduces negative environmental effects, is becoming more and more important. Because of the achievement of climate protection targets, photovoltaic (PV) energy has an increasing role in the global energy mix. This paper presents the technical and economic aspects of different photovoltaic system configurations designed to suit the Hungarian renewable energy regulations. In this study, five alternative PV configurations were examined for systems with a capacity from 50 kW to 500 kW, related to low- and medium-voltage installations. This article also introduces and explains the Hungarian economic PV and Feed-in-Tariff (FiT) regulations, where three different investment alternatives are analyzed with the help of economic indicators. This study could help stakeholders in the market (e.g., the Hungarian industry sector and local governments) understand the possible directions of technical and economic PV development. According to the results, the payback periods in all the studied economic-technical cases were below 10 years. The experimental results show that each investment option may be a good decision from an economic and technical point of view under the Hungarian regulations in force in 2019.


2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Timothy King Avordeh ◽  
Samuel Gyamfi ◽  
Alex Akwasi Opoku

Purpose The purpose of this paper is to investigate the impact of temperature on residential electricity demand in the city of Greater Accra, Ghana. It is believed that the increasing trend of temperatures may significantly affect people’s lives and demand for electricity from the national grid. Given the recurrent electricity crisis in Ghana, this study will investigate both the current and future residential energy demands in the light of temperature fluctuations. This will inform future power generation using renewable energy resources mix to find a sustainable solution to the recurrent energy demand challenges in Ghana. This study will help the Government of Ghana to better understand the temperature dependence of residential energy demand, which in turn will help in developing behavioral modification programs aimed at reducing energy consumption. Monthly data for the temperature and residential electricity consumption for Greater Accra Region from January 2007 to December 2018 obtained from the Ghana Meteorological Service (GMS) and Ghana Grid Company (Gridco), respectively, are used for the analysis. Design/methodology/approach This study used monthly time series data from 2007 to 2018. Data on monthly electricity demand and temperature are obtained from the Ghana Grid Company and GMS. The theoretical framework for residential electricity consumption, the log-linear demand equation and time series regression approaches was used for this study. To demonstrate certain desirable properties and to produce good estimators in this study, an analysis technique of ordinary least squares measurement was also applied. Findings This study showed an impact on residential electricity requirements in the selected regions of Greater Accra owing to temperature change. The analysis suggests a substantial positive response to an increase in temperature demand for residential electricity and thus indicates a growth of the region’s demand for electricity in the future because of temperature changes. As this analysis projects, the growth in the electricity demand seems too small for concern, perhaps because of the incoherence of the mechanisms used to regulate the temperature by the residents. However, two points should be considered when drawing any conclusions even in the case of Greater Accra alone. First, the growth in the demand for electricity shown in the present study is the growth of demand due only to increasing temperatures that do not consider changes in all the other factors driving the growth of demand. The electricity demand will in the future increase beyond what is induced by temperature, due to increasing demand, population and mechanization and other socioeconomic factors. Second, power consumption understated genuine electricity demand, owing to the massive shedding of loads (Dumsor) which occurred in Ghana from 2012 to 2015 in the analysis period that also applies in the Greater Accra region. Given both of these factors, the growth in demand for electricity is set to increase in response to climate change, which draws on the authorities to prepare more critically on capacity building which loads balancing. The results also revealed that monthly total residential electricity consumption, particularly the monthly peak electricity consumption in the city of Accra is highly sensitive to temperature. Therefore, the rise in temperature under different climate change scenarios would have a high impact on residential electricity consumption. This study reveals that the monthly total residential electricity demand in Greater Accra will increase by up to 3.1%. Research limitations/implications The research data was largely restricted to only one region in Ghana because of the inconsistencies in the data from the other regions. The only climate variable use was temperature because it was proven in the literature that it was the most dominant variable that affects electricity demand, so it was not out of place to use only this variable. The research, however, can be extended to capture the entire regions of the country if sponsorship and accurate data can be obtained. Practical implications The government as the policy and law-making authority has to play the most influential role to ensure adaptation at all levels toward the impact of climate change for residential consumers. It is the main responsibility of the government to arrange enough supports to help residential consumers adapt to climate change and try to make consumers self-sufficient by modification of certain behaviors rather than supply dependent. Government bodies need to carefully define their climate adaptation supports and incentive programs to influence residential-level consumption practices and demand management. Here, energy policies and investments need to be more strategic. The most critical problem is to identify the appropriate adaptation policies that favor the most vulnerable sectors such as the residential sector. Social implications To evaluate both mitigation and adaptation policies, it is important to estimate the effect of climate change on energy usage around the world. Existing empirical figures, however, are concentrated in Western nations, especially the USA. To predict how electricity usage will shift in the city of Greater Accra, Ghana, the authors used regular household electricity consumption data. Originality/value The motivation for this paper and in particular the empirical analysis for Ghana is originality for the literature. This paper demonstrates an adequate understanding of the relevant literature in modern times.


2018 ◽  
Vol 49 ◽  
pp. 00014
Author(s):  
Bartosz Chwieduk ◽  
Adam Szelągowski

The paper presents results of analysis of possible cooperation of a photovoltaic system with the space cooling devices. The size of the photovoltaic system was determined on the basis of electricity demand of the selected single family house. The demand for the electricity use for cooling and air conditioning had not been taken into account while calculating the size of PV system. On the basis of the heat balance of the building, the demand for cooling in the following hours of a year was determined. The demand for cooling and heating is affected by the heat transfer through walls, windows, floor, roof, and air exchanged through ventilation. Also solar and internal gains were taken into account. Based on Next, a cooling unit was selected. A cooling device was selected to provide enough energy to maintain the thermal comfort of the building in summer. Taking into account parameters of the selected device, the demand for electricity was determined. Based on time and hours of operation of electrical appliances in the building, a chart of electricity demand was created. The demand for cooling was included. Calculated values of the energy demand required to power all devices in the building were compared with the energy gains from the photovoltaic system. In order to calculate the energy generated by the PV system (in following hours of a year) the isotropic model of solar irradiation was used. The input solar radiation data on horizontal surface were downloaded from the website of the Ministry of Investment and Economic Development. In the last paragraphs, savings obtained in result of using the energy generated by the PV system to drive the space cooling system were determined and conclusions from the calculations were presented.


Author(s):  
F. Slama ◽  
H. Radjeai ◽  
S. Mouassa ◽  
A. Chouder

Purpose. In last decade the problem of energy management system (EMS) for electric network has received special attention from academic researchers and electricity companies. In this paper, a new algorithm for EMS of a photovoltaic (PV) grid connected system, combined to an storage system is proposed for reducing the character of intermittence of PVs power which infect the stability of electric grid. In simulation model, the PV system and the energy storage system are connected to the same DC bus, whereas EMS controls the power flow from the PV generator to the grid based on the predetermined level of PV power. In the case where the PV power is less than the predefined threshold, energy is stored in the batteries banc which will be employed in the peak energy demand (PED) times. Otherwise, it continues to feed the principal grid. The novelty of the proposed work lies in a new algorithm (smart algorithm) able to determine the most suitable (optimal) hours to switching between battery, Solar PVs, and principal grid based on historical consumption data and also determine the optimal amount of storage energy that be injected during the peak demand. Methods. The solution of the problem was implemented in the Matlab R2010a Platform and the simulation conducted on Laptop with a 2.5 GHz processor and 4 GB RAM. Results. Simulation results show that the proposed model schedules the time ON/OFF of the switch in the most optimal way, resulting in absolute control of power electric path, i.e. precise adaptation at the peak without compromising consumers comfort. In addition, other useful results can be directly obtained from the developed scheme. Thus, the results confirm the superiority of the proposed strategy compared to other improved techniques.


Clean Energy ◽  
2021 ◽  
Vol 5 (2) ◽  
pp. 273-287
Author(s):  
Ahmad Mayyas ◽  
Assia A Chadly ◽  
Iman Khaleel ◽  
Maher Maalouf

Abstract Green buildings have become broadly adopted in commercial and residential sectors with the objective of minimizing environmental impacts through reductions in energy usage and water usage and, to a lesser extent, minimizing environmental disturbances from the building site. In this paper, we develop and discuss a techno-economic model for a green commercial building that is 100% powered by a photovoltaic (PV) system in stand-alone configuration. A medium-sized office building in El Paso, TX was modelled to rely on a photovoltaic system to supply all of its electricity needs either directly from the PV system or through an energy-storage system (ESS) using Li-ion batteries (LIBs) or reversible fuel cells (RFCs). Cost results show that a 400-kW PV system can generate electricity at a cost of 2.21 cents/kWh in El Paso, TX and the average levelized cost of energy storage (LCOS) using 450-kW RFC is ~31.3 cents/kWh, while this could reach as low as 25.5 cents/kWh using a small LIB ESS. While the RFC provides the flexibility required to meet building-energy demand, LIBs may not be able to meet building needs unless the storage size is increased substantially, which in turn incurs more energy-storage cost, making LIBs less favourable from an economic perspective. Sensitivity analysis revealed that capital cost, discount rate and expected system lifetime play key roles in shaping the LCOS in both systems.


Sign in / Sign up

Export Citation Format

Share Document