Solid-phase epitaxy of Ti-implanted LiNbO3

1989 ◽  
Vol 4 (2) ◽  
pp. 412-416 ◽  
Author(s):  
D. B. Poker ◽  
D. K. Thomas
Keyword(s):  
Optical Waveguides ◽  
Solid Phase ◽  
Complete Removal ◽  
Amorphous Region ◽  
Liquid Nitrogen Temperature ◽  
High Dose ◽  
Solid Phase Epitaxy ◽  
Complete Recrystallization ◽  
Water Saturated ◽  
Saturated Oxygen

The solid-phase epitaxy of LiNbO3 following ion implantation of Ti dopant for the purpose of producing optical waveguides has been studied. Implanting 360-keV Ti at liquid nitrogen temperature produces a highly damaged region extending to a depth of about 400 nm. This essentially amorphous region can be recrystallized epitaxially by annealing in a water-saturated oxygen atmosphere at temperatures near 400 °C. though complete removal of all irradiation-induced damage requires temperatures in excess of 600 °C. The activation energy of the regrowth is 2.0 eV for implanted fluences below 3 ⊠ 1016 Ti/cm2. At higher fluences the regrowth proceeds more slowly, and Ti dopant segregates at the regrowth interface. Complete recrystallization following high-dose implantation requires annealing temperatures in excess of 800 °C.

Solid-Phase Epitaxy of Ti-Implanted LiNbO3

1987 ◽  
Vol 93 ◽  
Author(s):  
D. B. Poker
Keyword(s):  
Activation Energy ◽  
Optical Waveguides ◽  
Solid Phase ◽  
Complete Removal ◽  
Liquid Nitrogen Temperature ◽  
Index Of Refraction ◽  
Optical Index ◽  
Epitaxial Regrowth ◽  
Residual Damage ◽  
Water Saturated

ABSTRACTThe implantation of Ti into LiNbO3 has been studied as a means of altering the optical index of refraction to produce optical waveguides. Implanting 2 × 1017 atoms/cm2 of 360-keV Ti at liquid nitrogen temperature produces a highly damaged region extending to a depth of about 4000 Å. Solid-phase epitaxial regrowth of the LiNbO3 can be achieved by annealing in a water-saturated oxygen atmosphere at 400°C, though complete removal of the residual damage usually requires temperatures in excess of 800°C. The solid-phase epitaxial regrowth rate exhibits an activation energy of 2 eV at doses below 3 × 1016 Ti/cm2, but both the regrowth rate and activation energy decrease at higher doses. At doses above 1 × 1017 Ti/cm2, the solid-phase epitaxial regrowth occurs only at temperatures above 800°C.

Optical Waveguide Formation by Ion Implantation of Ti or Ag

1988 ◽  
Vol 100 ◽  
Author(s):  
D. B. Poker ◽  
D. K. Thomas
Keyword(s):  
Ion Implantation ◽  
Concentration Profile ◽  
Optical Waveguides ◽  
Annealing Temperature ◽  
Solid Phase ◽  
Effective Means ◽  
Complete Removal ◽  
Solid Phase Epitaxy ◽  
Annealing Temperatures ◽  
Residual Damage

ABSTRACTIon implantation of Ti into LINbO3 has been shown to be an effective means of producing optical waveguides, while maintaining better control over the resulting concentration profile of the dopant than can be achieved by in-diffusion. While undoped, amorphous LiNbO3 can be regrown by solid-phase epitaxy at 400°C with a regrowth velocity of 250 Å/min, the higher concentrations of Ti required to form a waveguide (∼10%) slow the regrowth considerably, so that temperatures approaching 800°C are used. Complete removal of residual damage requires annealing temperatures of 1000°C, not significantly lower than those used with in-diffusion. Solid phase epitaxy of Agimplanted LiNbO3, however, occurs at much lower temperatures. The regrowth is completed at 400°C, and annealing of all residual damage occurs at or below 800°C. Furthermore, the regrowth rate is independent of Ag concentration up to the highest dose implanted to date, 1 × 1017 Ag/cm2. The usefulness of Ag implantation for the formation of optical waveguides is limited, however, by the higher mobility of Ag at the annealing temperature, compared to Ti.

Ion Implantation of Ti INTO LiNbO3: Fabrication of Waveguides and Simple Modulators

1989 ◽  
Vol 152 ◽  
Author(s):  
C. W. White ◽  
D. K. Thomas ◽  
P. R. Ashley ◽  
W. S. C. Chang ◽  
C. Buchal
Keyword(s):  
Ion Implantation ◽  
Solid Phase ◽  
Surface Region ◽  
Amorphous Region ◽  
Index Of Refraction ◽  
Near Surface ◽  
Channel Waveguides ◽  
High Doses ◽  
Water Saturated ◽  
Saturated Oxygen

ABSTRACTIon implantation has been used to introduce Ti at very high doses (>3 × 1017 /cm2) into the near-surface region of LiNbO3 to change the index of refraction.’ In the as-implanted state, the near surface is amorphous. Thermal annealing in water-saturated oxygen 1000°C crystallizes the amorphous region and incorporates the Ti into substitutional sites in the lattice at concentrations that exceed 10 at.%. Recrystallization takes place by solid-phase epitaxy. Both planar and channel waveguides have been fabricated with optical attenuations of <1 dB/cm. Both Mach-Zehnder and Bragg modulators have been fabricated using Ti implantation of LiNbO3. The characteristics of these devices have been determined and will be reported. The higher Ti concentrations which can be achieved by implantation allows tighter mode confinement and smaller mode profiles than with Ti-diffused guides.

Solid-phase epitaxy of ion-implanted LiNbO3 for optical waveguide fabrication

1987 ◽  
Vol 2 (2) ◽  
pp. 222-230 ◽  
Author(s):  
Ch. Buchal ◽  
P. R. Ashley ◽  
B. R. Appleton
Keyword(s):  
Optical Waveguides ◽  
Solid Phase ◽  
Surface Region ◽  
Liquid Nitrogen Temperature ◽  
High Concentration ◽  
Near Surface ◽  
Crystalline Substrate ◽  
A New Technique ◽  
Waveguide Fabrication ◽  
Water Saturated

A new technique for successfully fabricating high-quality optical waveguides in LiNbO3 is reported. A high concentration of Ti is implanted with the substrate at liquid nitrogen temperature and an amorphous, Ti-rich, nonequilibrium phase is produced in the implanted, near-surface region. Subsequent thermal annealing in water-saturated oxygen atmosphere at up to 1000°C initiates solid-phase epitaxial regrowth onto the crystalline substrate. A highquality single crystalline layer results that is rich in Ti and has excellent waveguiding properties.

Microstructure of Ultra High Dose Self Implanted Silicon

1997 ◽  
Vol 504 ◽  
Author(s):  
X. F. Zhu ◽  
J. S. Williams ◽  
D. J. Llewellyn ◽  
J. C. McCallum
Keyword(s):  
Liquid Nitrogen ◽  
Elevated Temperatures ◽  
Solid Phase ◽  
Liquid Nitrogen Temperature ◽  
High Dose ◽  
Solid Phase Epitaxy ◽  
Amorphous Si ◽  
Strong Dynamic ◽  
High Dose Implantation ◽  
Amorphous Part

ABSTRACTThis study has investigated the microstructure of ultra high dose (∼ 1018 cm−2) self implantation into Si. Implants have been carried out into both (100) Si and pre-amorphised Si as a function of implant temperature between liquid nitrogen temperature and 350°C. Results show that high dose implantation into completely amorphous Si (a-Si) produces layers which regrow quite well during subsequent solid phase epitaxy. In contrast, implantation into crystalline Si (c-Si) or part amorphous/part crystalline Si can lead to rich and varied microstructures at elevated temperatures, even extending to porous-like structures in some cases. Strong dynamic annealing and agglomeration of points defects in c-Si is thought to be responsible for such behaviour.

scholarly journals Formation of Buried Epitaxial Si-Ge Alloy Layers in Si Crystal by High Dose Ge ION Implantation

1991 ◽  
Vol 235 ◽  
Author(s):  
Kin Man Yu ◽  
Ian G. Brown ◽  
Seongil Im
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Lattice Mismatch ◽  
Solid Phase ◽  
Metal Vapor ◽  
Ion Source ◽  
Vacuum Arc ◽  
High Dose ◽  
Solid Phase Epitaxy ◽  
Ion Channeling

ABSTRACTWe have synthesized single crystal Si1−xGex alloy layers in Si <100> crystals by high dose Ge ion implantation and solid phase epitaxy. The implantation was performed using the metal vapor vacuum arc (Mevva) ion source. Ge ions at mean energies of 70 and 100 keV and with doses ranging from 1×1016 to to 7×1016 ions/cm2 were implanted into Si <100> crystals at room temperature, resulting in the formation of Si1−xGex alloy layers with peak Ge concentrations of 4 to 13 atomic %. Epitaxial regrowth of the amorphous layers was initiated by thermal annealing at temperatures higher than 500°C. The solid phase epitaxy process, the crystal quality, microstructures, interface morphology and defect structures were characterized by ion channeling and transmission electron microscopy. Compositionally graded single crystal Si1−xGex layers with full width at half maximum ∼100nm were formed under a ∼30nm Si layer after annealing at 600°C for 15 min. A high density of defects was found in the layers as well as in the substrate Si just below the original amorphous/crystalline interface. The concentration of these defects was significantly reduced after annealing at 900°C. The kinetics of the regrowth process, the crystalline quality of the alloy layers, the annealing characteristics of the defects, and the strains due to the lattice mismatch between the alloy and the substrate are discussed.

Solid Phase Epitaxy of Implanted Si-Ge-C Alloys

1995 ◽  
Vol 388 ◽  
Author(s):  
Xiang Lu ◽  
Nathan W. Cheung
Keyword(s):  
Lattice Mismatch ◽  
Solid Phase ◽  
Metal Vapor ◽  
High Dose Rate ◽  
Ion Source ◽  
Vacuum Arc ◽  
High Dose ◽  
Solid Phase Epitaxy ◽  
Cross Sectional ◽  
Rutherford Back Scattering

AbstractSi1-x-yGexCy/Si heterostuctures were formed on Si (100) surface by Ge and C implantation with a high dose rate MEtal - Vapor Vacuum arc (MEVVA) ion source and subsequent Solid Phase Epitaxy (SPE). after thermal annealing in the temperature range from 600 °C to 1200 °C, the implanted layer was studied using Rutherford Back-scattering Spectrometry (RBS), cross-sectional High Resolution Transmission Electron Microscopy (HRTEM) and fourbounce X-ray Diffraction (XRD) measurement. Due to the small lattice constant and wide bandgap of SiC, the incorporation of C into Si-Ge can provide a complementary material to Si-Ge for bandgap engineering of Si-based heterojunction structure. Polycrystals are formed at temperature at and below 1000 °C thermal growth, while single crystal epitaxial layer is formed at 1100 °C and beyond. XRD measurements near Si (004) peak confirm the compensation of the Si1-x Gex lattice mismatch strain by substitutional C. C implantation is also found to suppress the End of Range (EOR) defect growth.

Solid Phase Epitaxy of Strained Si1−xGex Alloys Formed by Highdose Ion Implantation into Silicon

1990 ◽  
Vol 187 ◽  
Author(s):  
D. J. Howard ◽  
D. C. Paine ◽  
N. G. Stoffel
Keyword(s):  
Ion Implantation ◽  
Strain Energy ◽  
Critical Strain ◽  
Solid Phase ◽  
Stacking Faults ◽  
New Method ◽  
High Dose ◽  
Solid Phase Epitaxy ◽  
Cross Sectional ◽  
Si Wafer

AbstractIn this paper we propose a new method for the synthesis of Si1−xGex strained-layer alloys using high-dose ion implantation of 74Ge at 200 keV into a preamorphized <001> Si wafer followed by solid phase epitaxy (SPE). Cross-sectional TEM was performed on samples at various stages of regrowth which revealed the evolution of the amorphous/crystalline interface and the development of strain relieving defects during SPE. We report that stacking faults are kinetically favored during SPE of Si1−xGex but are energetically feasible only above a critical strain energy. We propose a model that is based on the well known Matthews and Blakeslee approach which predicts the onset of stacking faults during SPE of high-dose ion implant-synthesized Si1−xGex/Si.

Sign in / Sign up

Export Citation Format

Share Document