Evaluation of Infection Resistance of Biological Implants through CMP based Micro-Patterning

2012 ◽  
Vol 1464 ◽  
Author(s):  
G. Bahar Basim ◽  
Zeynep Ozdemir ◽  
Ayse Karagoz
Keyword(s):  
Surface Roughness ◽  
Dental Implants ◽  
Growth Response ◽  
Semiconductor Industry ◽  
Cardiac Pacemakers ◽  
Bacteria Growth ◽  
Micro Patterning ◽  
Biological Implants ◽  
Infection Resistance ◽  
Materials Used

ABSTRACTBiomaterials are widely used for dental implants, orthopedic devices, cardiac pacemakers and catheters. One of the main concerns on using bio-implants is the risk of infection on the materials used. In this study, our aim is to quantify the effect of controlled surface roughness on the infection resistance of the titanium based bio-materials which are commonly used for orthopedic devices and dental implants. To modify the surface roughness of the surfaces in a controlled manner, Chemical Mechanical Polishing (CMP) technique, which is extensively used in semiconductor industry for the planarization of the interlayer dielectrics and metals, is utilized. To determine the infection resistance of the created films with varying surface roughness, bacteria growth response was studied on titanium plates after CMP.

Effect of Surface Roughness on Slip Resistance of Rubber

2011 ◽  
Vol 189-193 ◽  
pp. 1538-1542
Author(s):  
Li Xiao Jia ◽  
Yong Zhen Zhang ◽  
Yong Ping Niu ◽  
San Ming Du ◽  
Jian Li
Keyword(s):  
Surface Roughness ◽  
Correlation Coefficient ◽  
Correlation Coefficients ◽  
Roughness Parameters ◽  
Test Conditions ◽  
Slip Resistance ◽  
Materials Used ◽  
Almost All ◽  
Effect Of Surface

In order to decrease accidents of slips and falls, COFs of rubber samples with different surface roughness were measured by Brungraber Mark II. And the correlation coefficients between roughness parameters and COF were calculated. The rusults have shown that the COF increases with surface roughness and the correlation coefficient between Sq and COF is highest. In general, almost all the roughness parameters used in the study have high correlation with COF. Parameters had the highest correlation with COF depends on the materials used and test conditions.

Possible Causes in Breaking of Dental Implants Research

2017 ◽  
Vol 907 ◽  
pp. 104-118
Author(s):  
Maria Stoicănescu ◽  
Eliza Buzamet ◽  
Dragos Vladimir Budei ◽  
Valentin Craciun ◽  
Roxana Budei ◽  
...  
Keyword(s):  
Dental Implants ◽  
Dental Implant ◽  
Scientific Literature ◽  
Surface Characteristics ◽  
Raw Material ◽  
New Materials ◽  
Materials Used ◽  
Type Of Failure ◽  
First Time ◽  
Consequent Increase

Dental implants are becoming increasingly used in current dental practice. This increased demand has motivated manufacturers to develop varieties of product through design, but also looking for new materials used to improve surface characteristics in order to obtain a better osseointegration. But the increase in the use of implants goes to a consequent increase in the number of failures. These failures are caused either by treatment complications (peri-implantitis), by fatigue breakage under mechanical over-stress, by defective raw material, or due to errors during the insertion procedures. Although they are rare, these complications are serious in dentistry. Before to market a dental implant to clinical practitioners, the product is validated among other determinations in number of biocompatibility research. Raw material issues, details about its structure and properties are less published by the scientific literature, but all this are subject of a carefully analysis of the producers. Breaking of dental implants during surgical procedures, during the prosthetic procedures or during use (chewing, bruxism, accidents, etc.), is the second most common cause of loss of an implant after consecutive peri-implantitis rejection. Although the frequency of this type of failure for a dental implant is much smaller than those caused by the peri-implantitis, a detailed study of broken implants can explain possible causes. The use of scanning electron microscopy (SEM) in the study of the cleave areas explain the production mechanism of cleavages, starting from micro-fissures in the alloy used for the production of dental implants. These micro-fissures in weak areas of the implant (anti-rotational corners of the polygons, etc.) could generate a serious risk of cleavage first time when a higher force is applied.

Evaluation of the nanodebris produced by in vitro degradation of titanium-based dental implants in the presence of bacteria using single particle and single cell inductively coupled plasma mass spectrometry.

2021 ◽  
Author(s):  
Marzia Cosmi ◽  
Nathaly Gonzalez-Quiñonez ◽  
Pablo Tejerina Díaz ◽  
Ángel Manteca ◽  
Elisa Blanco González ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Dental Implants ◽  
Inductively Coupled Plasma ◽  
Metallic Materials ◽  
In Vitro Degradation ◽  
Inductively Coupled ◽  
Oral Environment ◽  
Plasma Mass Spectrometry ◽  
Materials Used

The bio-tribocorrosion of metallic materials used for dental implants (Ti and alloys) in the oral environment involves the production of metallic debris in the ionic, but also in the nanoparticulated...

Functional Behaviour of Human Periodontal Ligament Cells around Various Dental Implants

2007 ◽  
Vol 361-363 ◽  
pp. 837-840 ◽  
Author(s):  
Xiao Ting Luo ◽  
Zhen Gao ◽  
Shi Gui Yan ◽  
Wei Deng ◽  
Wen Shu Zhang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Dental Implants ◽  
Periodontal Ligament ◽  
Cell Counting ◽  
Immunofluorescent Staining ◽  
Periodontal Ligament Cells ◽  
Human Periodontal Ligament Cells ◽  
Proliferation And Differentiation ◽  
In Vitro Systems

In the present investigation, four titanium (Ti) surfaces of dental implants were compared through in vitro systems. The surface roughness of Ti was measured by TR240 mobile surface roughmeter. The Ti implants were seeded with human periodontal ligament cells (hPLDCs) and maintained for a period of 0-7 days. The adhesion, proliferation, and differentiation of hPLDCs were observed by using Cell morphology, cell counting and Osteocalcin (OC) immunofluorescent staining. Results suggest that surface roughness of titanium favors hPDLCs behavior and improves cell adhesion, proliferation, and differentiation.

scholarly journals Prosthetics of dental implants- surface roughness and P. gingivalis growth in vitro

2018 ◽  
Vol 29 ◽  
pp. 356-356
Author(s):  
Julius Maminskas ◽  
Monika Zaleckyte ◽  
Jurgis Pilipavicius ◽  
Aivaras Kareiva ◽  
Gediminas Zekonis ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Dental Implants

scholarly journals Experimental Investigation into the Effect of Surface Roughness and Mechanical Properties of 3D-Printed Titanium Ti-64 ELI after Heat Treatment

2021 ◽  
Author(s):  
Lebogang Lebea ◽  
Harry M Ngwangwa ◽  
Dawood Desai ◽  
Fuluphelo Nemavhola
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Dental Implants ◽  
Dental Implant ◽  
Complex Geometry ◽  
Poor Performance ◽  
Vital Role ◽  
Ultimate Tensile Stress ◽  
3D Printed ◽  
Effect Of Surface

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Comparison of Sputtered Titanium Nitride on Silicon Dioxide and Aluminum-Alloy Thin Films

1997 ◽  
Vol 3 (S2) ◽  
pp. 469-470
Author(s):  
J.L. Drown ◽  
S.M. Merchant ◽  
M.E. Gross ◽  
D. Eaglesham ◽  
L.A. Giannuzzi ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Titanium Nitride ◽  
Physical Vapor Deposition ◽  
Semiconductor Industry ◽  
Microstructural Characterization ◽  
Growth Conditions ◽  
Alloy Film ◽  
Al Alloy ◽  
Orientation Relationships ◽  
Materials Used

Titanium nitride (TiN) films are used as anti-reflection coatings (ARC) on aluminum (Al) films to facilitate lithography processes during multilevel metallization for the manufacture of integrated circuits on silicon-based (Si) semiconductor devices. It is generally accepted in the literature that the microstructure of multilevel metal stacks is influenced by the texture of the substrate. For the case of interconnect materials used in the semiconductor industry, a typical metal stack is as follows: Titanium/Titanium Nitride/Al-alloy/ARC-Titanium Nitride. The Ti/TiN layer underneath the Al-alloy film is used as a barrier stack to prevent junction spiking. The Ti/TiN underlayer also determines the growth conditions (crystallography and orientation relationships) of the subsequent Al-alloy film.This study focuses on the microstructural characterization of the ARC-TiN layer on Si-oxide and Ti/TiN/Al-alloy substrates that are fabricated under similar conditions using conventional physical vapor deposition (PVD - sputtering) techniques. The ARC-TiN microstructure was investigated by transmission electron microscopy (TEM) using a Philips EM430 operating at 300 kV.

scholarly journals Laser Surface Texturing and Electropolishing of CoCr and Ti6Al4V-ELI Alloys for Biomedical Applications

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5203
Author(s):  
Jesús A. Sandoval-Robles ◽  
Ciro A. Rodríguez ◽  
Erika García-López
Keyword(s):  
Surface Roughness ◽  
Unit Length ◽  
Surface Texturing ◽  
Orthopedic Implants ◽  
Laser Surface Texturing ◽  
Material Surface ◽  
Roughness Parameters ◽  
X Ray ◽  
Surface Roughness Parameters ◽  
Materials Used

The interplay between a prosthetic and tissue represents an important factor for the fixation of orthopedic implants. Laser texturing tests and electropolishing were performed on two materials used in the fabrication of medical devices, i.e., CoCr and Ti6Al4V-ELI alloys. The material surface was textured with a diode-pumped solid state (DPSS) laser and its effect on the surface quality and material modification, under different combinations of laser power and marking speed, were investigated. Our results indicate that an increment of energy per unit length causes an incremental trend in surface roughness parameters. Additionally, phase transformation on the surface of both alloys was achieved. Chemical analysis by energy dispersive X-ray spectrometer (EDX) shows the formation of (Co(Cr,Mo)) phase and the M23C6 precipitate on the CoCr surface; while quantitative analysis of the X-ray diffractometer (XRD) results demonstrates the oxidation of the Ti alloy with the formation of Ti2O and Ti6O from the reduction of the α-Ti phase. The behaviors were both related with an increase of the energy per unit length. Control of the final surface roughness was achieved by an electropolishing post-treatment, minimizing the as-treated values. After polishing, a reduction of surface roughness parameters was obtained in a range between 3% and 44%, while no changes in chemical composition or present phases were observed.

scholarly journals Morphological and Chemical Characterization of Titanium and Zirconia Dental Implants with Different Macro- and Micro-Structure

2020 ◽  
Vol 10 (21) ◽  
pp. 7520
Author(s):  
Maria Menini ◽  
Francesco Pera ◽  
Francesco Bagnasco ◽  
Francesca Delucchi ◽  
Elisa Morganti ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Dental Implants ◽  
Chemical Characterization ◽  
Sample Surface ◽  
Titanium Implants ◽  
Good Care ◽  
Micro Structure ◽  
Chemical Residues ◽  
Micro Structures

Background: The aim of this study was to evaluate the macro- and micro-structure and the chemical composition of the surface of 5 different commercially available dental implants. Roughness values were also calculated. Materials and Methods: 1 zirconia implant (NobelPearl of Nobel Biocare) and 4 titanium implants, Syra (Sweden&Martina), Prama (Sweden&Martina), T3 (Biomet 3i), and Shard (Mech&Human), were analyzed through SEM-EDX analysis and quantitative evaluation of surface roughness (1 sample), and XPS chemical analysis (1 sample). Surface roughness was quantitatively assessed using the stereo-SEM method (SSEM). The following area roughness parameters were calculated, according to ISO25178: Sa, Sz, and Sdr. Results: From the SEM observations, all the implants analyzed presented modern well-developed micro-structures as the result of the specific process of double acid etching alone or combined with other additional treatments. Roughness values were generally greater at the level of the implant body and lower at the collar. The chemical characterization of the implant surfaces exhibited excellent results for all of the implants and indicated good care in the production processes. Conclusions: All the samples were well-conceived in terms of topography and surface roughness, and clean in terms of chemical residues.

Sign in / Sign up

Export Citation Format

Share Document