Dependence of Annealing Temperature on the Conductivity Changes of ZnO and MgZnO Nanoparticle Thin Films from Annealing in a Hydrogen Atmosphere at Mild Temperatures

2012 ◽  
Vol 1394 ◽  
Author(s):  
Christine Berven ◽  
Lorena Sanchez ◽  
Sirisha Chava ◽  
Hannah Marie Young ◽  
Joseph Dick ◽  
...  

ABSTRACTWe report apparent robust doping of ZnO and MgxZn1-xO (x ∼20%) nanoparticle films by annealing in hydrogen gas. The annealing was done at sequentially higher temperatures from about 20 °C to 140 °C. The effect of the annealing was determined by comparing current-voltage measurements of the samples at room-temperature and in vacuum after each annealing cycle.The nanoparticles were grown using an aqueous solution and heating process that created thinfilms of ZnO or MgZnO nanoparticles with diameters of about 30 nm. When exposed to hydrogen gas at room-temperature or after annealing at temperatures up to about 100 °C, no measureable changes to the room-temperature vacuum conductivity of the films was observed. However, when the samples were annealed at temperatures above 100 °C, an appreciable robust increase in the room-temperature conductance in vacuum occurred. Annealing at the maximum temperature (∼135-140 °C) resulted in about a factor of about twenty increase in the conductivity. Furthermore, the ratio of the conductance of the ZnO and MgZnO nanoparticle films while being annealed to their conductance at room-temperature were found to increase and then decrease for increasing annealing temperatures. Maximum changes of about five-fold and seven-fold for the MgZnO and ZnO samples, respectively, were found to occur at temperatures just below the annealing temperature threshold for the onset of the robust hydrogen gas doping. Comparisons of these results to other work on bulk ZnO and MgZnO films and reasons for this behavior will be discussed.

2006 ◽  
Vol 527-529 ◽  
pp. 819-822
Author(s):  
Fabio Bergamini ◽  
Shailaja P. Rao ◽  
Antonella Poggi ◽  
Fabrizio Tamarri ◽  
Stephen E. Saddow ◽  
...  

This work reports the realization and characterization of 4H-SiC p+/n diodes with the p+ anodes made by Al+ ion implantation at 400°C and post-implantation annealing in silane ambient in a cold-wall low-pressure CVD reactor. The Al depth profile was almost box shaped with a height of 6×1019 cm-3 and a depth of 160 nm. Implant anneals were performed in the temperature range from 1600°C to 1700°C. As the annealing temperature was increased, the silane flow rate was also increased. This annealing process yields a smooth surface with a roughness of the implanted area of 1.7 - 5.3 nm with increasing annealing temperature. The resistivity of the implanted layer, measured at room temperature, decreased for increasing annealing temperatures with a minimum value of 1.4 0-cm measured for the sample annealed at 1700°C. Considering only the current-voltage characteristic of a diode that could be modeled as an abrupt p/n junction within the frame of the Shockley theory, the diode process yield and the diode leakage current decreased, respectively, from 93% to 47% and from 2×10-7 Acm-2 to 1×10-8 Acm-2 at 100 V reverse bias, for increasing post implantation annealing temperature.


2021 ◽  
Author(s):  
Mayyada Muttar Fdhala ◽  
◽  
Ayser A. Hemed ◽  
Ramiz A. Al-Ansari ◽  
Raad M. Al-Haddad ◽  
...  

Schottky Diode (SD) Al/a-Se/Au as a solar cell (SC) was prepared by thermal evaporation technique (TET) on glass thin slide as a substrate under vacuum (10!" mbar). The Schottky Barrier (SB) have been prepared with different thicknesses (300, 500 and 700) nm in room temperature and (343) K annealing temperature. The current-voltage (IV) physical properties of the SB have got rectification properties and approved as a SC. This cell is developed with increased annealing temperatures and thickness of layers of SD. Experience under lighting shows good efficiency (η), which increased linearly with both thickness and annealing temperatures from (0.0318% to 4.064%) and from (0.0318% to 0.4778%). This is for three values of lighting power density (160, 230, 400) 𝑚𝑊/𝑐𝑚# in which the behave is similar. The best efficiency obtained in this work was (15.286)% at a power density of 400 𝑚𝑊/𝑐𝑚# , with thickness 700nm and 343K annealing temperature. Also (12.407)% at 230 𝑚𝑊/𝑐𝑚#, with thickness 500nm for the same annealing temperature.


2011 ◽  
Vol 110-116 ◽  
pp. 1094-1098
Author(s):  
Haleh Kangarlou ◽  
Mehdi Bahrami Gharahasanloo ◽  
Akbar Abdi Saray ◽  
Reza Mohammadi Gharabagh

Ti films of same thickness, and near normal deposition angle, and same deposition rate were deposited on glass substrates, at room temperature, under UHV conditions. Different annealing temperatures as 393K, 493K and 593K with uniform 8 cm3/sec, oxygen flow, were used for producing titanium oxide layers. Their nanostructures were determined by AFM and XRD methods. Roughness of the films changed due to annealing process. The gettering property of Ti and annealing temperature can play an important role in the nanostructure of the films.


2018 ◽  
Vol 924 ◽  
pp. 333-338 ◽  
Author(s):  
Roberta Nipoti ◽  
Alberto Carnera ◽  
Giovanni Alfieri ◽  
Lukas Kranz

The electrical activation of 1×1020cm-3implanted Al in 4H-SiC has been studied in the temperature range 1500 - 1950 °C by the analysis of the sheet resistance of the Al implanted layers, as measured at room temperature. The minimum annealing time for reaching stationary electrical at fixed annealing temperature has been found. The samples with stationary electrical activation have been used to estimate the thermal activation energy for the electrical activation of the implanted Al.


2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
H. Abdullah ◽  
S. Habibi

CuInSe2(CIS) thin films are successfully prepared by electron beam evaporation. Pure Cu, In, and Se powders were mixed and ground in a grinder and made into a pellet. The pallets were deposited via electron beam evaporation on FTO substrates and were varied by varying the annealing temperatures, at room temperature, 250°C, 300°C, and 350°C. Samples were analysed by X-ray diffractometry (XRD) for crystallinity and field-emission scanning electron microscopy (FESEM) for grain size and thickness. I-V measurements were used to measure the efficiency of the CuInSe2/ZnS solar cells. XRD results show that the crystallinity of the films improved as the temperature was increased. The temperature dependence of crystallinity indicates polycrystalline behaviour in the CuInSe2films with (1 1 1), (2 2 0)/(2 0 4), and (3 1 2)/(1 1 6) planes at 27°, 45°, and 53°, respectively. FESEM images show the homogeneity of the CuInSe2formed. I-V measurements indicated that higher annealing temperatures increase the efficiency of CuInSe2solar cells from approximately 0.99% for the as-deposited films to 1.12% for the annealed films. Hence, we can conclude that the overall cell performance is strongly dependent on the annealing temperature.


2012 ◽  
Vol 184 ◽  
pp. 307-312 ◽  
Author(s):  
A. Kazakewitsch ◽  
Werner Riehemann

Aluminum-matrix-nanoparticle-composites were produced by ball milling of micro scale aluminum powder in air atmosphere with subsequent consolidation by hot extrusion and also additional hot swaging. They were investigated in this condition after step by step isochronal annealing with successive increasing annealing temperature and quenching into water to room temperature. The material was investigated by amplitude dependent damping, hardness and density measurements, all at room temperature. For all measured amplitude dependent internal friction (ADIF) curves the damping increases with increasing strain amplitude. After some annealing treatments a knee occurs in the medium strain amplitude region of these curves. Moreover between annealing temperatures from 360°C to 480°C the strain dependent damping becomes a maximum, i.e. a peak in the ADIF curves occurs. Other ADIF curves of quenched and fatigued material show characteristic peaks that can be attributed to individual single cracks. It is shown that all these effects are due to the formation, opening and compression of cracks present in the sample or created by thermally exerted stresses.


Author(s):  
Kailong Hu ◽  
Samuel Jeong ◽  
Mitsuru Wakisaka ◽  
Jun-ichi Fujita ◽  
Yoshikazu Ito

Bottom-up synthesis of porous NiMo alloy reduced by NiMoO4 nanofibers was systematically investigated to fabricate non-noble metal porous electrodes for hydrogen production. The different annealing temperatures of NiMoO4 nanofibers under hydrogen atmosphere reveal that the 950 °C annealing temperature is a key to produce bicontinuous and monorhinic porous NiMo alloy without oxide phases. The porous NiMo alloy as cathodes in electrical water splitting demonstrates not only almost identical catalytic activity with commercial Pt/C, but also superb stability for 12 days.


Author(s):  
Kailong Hu ◽  
Samuel Jeong ◽  
Mitsuru Wakisaka ◽  
Jun-ichi Fujita ◽  
Yoshikazu Ito

Bottom-up synthesis of porous NiMo alloy reduced by NiMoO4 nanofibers was systematically investigated to fabricate non-noble metal porous electrodes for hydrogen production. The different annealing temperatures of NiMoO4 nanofibers under hydrogen atmosphere reveal that the 950 °C annealing temperature is a key to produce bicontinuous porous NiMo alloy without oxide phases. The porous NiMo alloy as cathodes in electrical water splitting demonstrates not only almost identical catalytic activity with commercial Pt/C in 1.0 M KOH solution, but also superb stability for 12 days at an electrode potential of −200 mV (v.s. RHE).


2009 ◽  
Vol 609 ◽  
pp. 261-264 ◽  
Author(s):  
N. Zouadi ◽  
N. Gabouze ◽  
D. Bradai ◽  
D. Dahmane

The hydrogen-sensing property of new type field-effect gas sensor device was studied. The device had an FET structure based on porous silicon. Adsorption of molecules into the porous silicon strongly changes the electrical properties of the transistor structure. Interestingly, the current variation induced by Hydrogen gas vapour that is the sensitivity of the sensor can be electrically tuned by changing polarization voltage. It has been shown that the device exhibited excellent hydrogen-sensing characteristic at room temperature. The results show that current-voltage characteristics are modified by the gas reactivity on the PS surface. In conclusion, the FET gas sensor based on porous silicon shows a rapid response to low concentration of the hydrogen gas at room temperature.


Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 470
Author(s):  
Xiaolu Yuan ◽  
Jiangwei Liu ◽  
Jinlong Liu ◽  
Junjun Wei ◽  
Bo Da ◽  
...  

Ohmic contact with high thermal stability is essential to promote hydrogen-terminated diamond (H-diamond) electronic devices for high-temperature applications. Here, the ohmic contact characteristics of Ni/H-diamond at annealing temperatures up to 900 °C are investigated. The measured current–voltage curves and deduced specific contact resistance (ρC) are used to evaluate the quality of the contact properties. Schottky contacts are formed for the as-received and 300 °C-annealed Ni/H-diamonds. When the annealing temperature is increased to 500 °C, the ohmic contact properties are formed with the ρC of 1.5 × 10−3 Ω·cm2 for the Ni/H-diamond. As the annealing temperature rises to 900 °C, the ρC is determined to be as low as 6.0 × 10−5 Ω·cm2. It is believed that the formation of Ni-related carbides at the Ni/H-diamond interface promotes the decrease in ρC. The Ni metal is extremely promising to be used as the ohmic contact electrode for the H-diamond-based electronic devices at temperature up to 900 °C.


Sign in / Sign up

Export Citation Format

Share Document