Identifying the limitation of Oliver and Pharr method in characterizing the viscoelastic-plastic materials with respect to indenter geometry

2008 ◽  
Vol 1137 ◽  
Author(s):  
Keerthika Balasundaram ◽  
Yanping Cao ◽  
Dierk Raabe
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Polymeric Materials ◽  
Analysis Method ◽  
Correct Evaluation ◽  
Nano Scale ◽  
Plastic Materials ◽  
Indenter Geometry

AbstractNanoindentation tests are widely used in recent years to characterize the mechanical properties of viscoelastic-plastic materials like polymers and biomaterials at the micro or nano-scale using the analysis method proposed by Oliver & Pharr (OP). However, recent studies revealed that the mechanical properties of viscoelastic-plastic (polymeric) materials determined using the OP method does not lead to a correct evaluation of Young's modulus. A systematic experimental study is performed with different indenter geometries like spherical and Berkovich geometries using various polymers in order to identify the limitations of the OP method.

Influence of the Porous Volume in the Structure of Resin Bond Composite Abrasives by its Mechanical Performance

2020 ◽  
Author(s):  
Matheus de Mendonça Chitan ◽  
Katia Cristiane Gandolpho Candioto
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Low Cost ◽  
Polymeric Materials ◽  
Porous Volume ◽  
The Impact

Abstract Abrasive tools consist of abrasive grains, binder and pores. Binders are the matrix of the material and may be of the metallic, vitrified or resin type. The wide use of polymeric materials (resinoid) is due to their low cost and excellent mechanical properties. The grain has the function of roughing the material, the binder, on the other hand, has the characteristics of ensuring grain adhesion and the pores in the structure are responsible for cooling the abrasive tool. In this work, we report the preparation and evaluation of the mechanical characteristics of resin bond composite abrasives with different structures based on the porous concentration. The composite abrasives were made with phenolic resin and alumina grains. Four different structures were studied from 10 to 30% of porous volume fraction with 50% of grain volume fraction. The concentration of porous and bond in the structure composition were employed to compare the mechanical performance of the prepared composite abrasive. To evaluate the mechanical properties of composites, Impact strength, Young’s Modulus by impulse excitation and flexural strength were realized. It was observed that as the porosity is higher, the impact resistance (absorbed energy) is lower, which confirms the lower resistance produced by the surface area contact (grain/binder) and a greater accumulation of tension in the binder material, the higher porosity value, higher the flexural strength value until 20% of porosity. Samples with higher volumes level of porosity presented lower Young’s Modulus but the presence of pores produced by volatiles by-products (mainly water) should act as stress concentrators, thus favoring lower mechanical properties at the resin-grain interface.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

scholarly journals First principles computation of composition dependent elastic constants of omega in titanium alloys: implications on mechanical behavior

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
R. Salloom ◽  
S. A. Mantri ◽  
R. Banerjee ◽  
S. G. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
First Principles ◽  
Young's Modulus ◽  
Group Vi ◽  
Group V ◽  
Β Phase ◽  
Ti Alloys ◽  
Ω Phase ◽  
Stabilizer Concentration

AbstractFor decades the poor mechanical properties of Ti alloys were attributed to the intrinsic brittleness of the hexagonal ω-phase that has fewer than 5-independent slip systems. We contradict this conventional wisdom by coupling first-principles and cluster expansion calculations with experiments. We show that the elastic properties of the ω-phase can be systematically varied as a function of its composition to enhance both the ductility and strength of the Ti-alloy. Studies with five prototypical β-stabilizer solutes (Nb, Ta, V, Mo, and W) show that increasing β-stabilizer concentration destabilizes the ω-phase, in agreement with experiments. The Young’s modulus of ω-phase also decreased at larger concentration of β-stabilizers. Within the region of ω-phase stability, addition of Nb, Ta, and V (Group-V elements) decreased Young’s modulus more steeply compared to Mo and W (Group-VI elements) additions. The higher values of Young’s modulus of Ti–W and Ti–Mo binaries is related to the stronger stabilization of ω-phase due to the higher number of valence electrons. Density of states (DOS) calculations also revealed a stronger covalent bonding in the ω-phase compared to a metallic bonding in β-phase, and indicate that alloying is a promising route to enhance the ω-phase’s ductility. Overall, the mechanical properties of ω-phase predicted by our calculations agree well with the available experiments. Importantly, our study reveals that ω precipitates are not intrinsically embrittling and detrimental, and that we can create Ti-alloys with both good ductility and strength by tailoring ω precipitates' composition instead of completely eliminating them.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

scholarly journals Phase Formation, Microstructure and Mechanical Properties of Mg67Ag33 as Potential Biomaterial

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 461
Author(s):  
Konrad Kosiba ◽  
Konda Gokuldoss Prashanth ◽  
Sergio Scudino
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Equilibrium Phase ◽  
Antibacterial Properties ◽  
Equilibrium Phase Diagram ◽  
Compressive Yield Strength ◽  
X Ray ◽  
Fine Grained ◽  
Equilibrium Phases

The phase and microstructure formation as well as mechanical properties of the rapidly solidified Mg67Ag33 (at. %) alloy were investigated. Owing to kinetic constraints effective during rapid cooling, the formation of equilibrium phases is suppressed. Instead, the microstructure is mainly composed of oversaturated hexagonal closest packed Mg-based dendrites surrounded by a mixture of phases, as probed by X-ray diffraction, electron microscopy and energy dispersive X-ray spectroscopy. A possible non-equilibrium phase diagram is suggested. Mainly because of the fine-grained dendritic and interdendritic microstructure, the material shows appreciable mechanical properties, such as a compressive yield strength and Young’s modulus of 245 ± 5 MPa and 63 ± 2 GPa, respectively. Due to this low Young’s modulus, the Mg67Ag33 alloy has potential for usage as biomaterial and challenges ahead, such as biomechanical compatibility, biodegradability and antibacterial properties are outlined.

scholarly journals Effect of Nanopores on Mechanical Properties of the Shape Memory Alloy

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 529
Author(s):  
Chunzhi Du ◽  
Zhifan Li ◽  
Bingfei Liu
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Shape Memory ◽  
Young’S Modulus ◽  
Residual Strain ◽  
Surface Effect ◽  
Young's Modulus ◽  
Strain Curve ◽  
Stress Strain ◽  
Strength Limit

Nanoporous Shape Memory Alloys (SMA) are widely used in aerospace, military industry, medical and health and other fields. More and more attention has been paid to its mechanical properties. In particular, when the size of the pores is reduced to the nanometer level, the effect of the surface effect of the nanoporous material on the mechanical properties of the SMA will increase sharply, and the residual strain of the SMA material will change with the nanoporosity. In this work, the expression of Young’s modulus of nanopore SMA considering surface effects is first derived, which is a function of nanoporosity and nanopore size. Based on the obtained Young’s modulus, a constitutive model of nanoporous SMA considering residual strain is established. Then, the stress–strain curve of dense SMA based on the new constitutive model is drawn by numerical method. The results are in good agreement with the simulation results in the published literature. Finally, the stress-strain curves of SMA with different nanoporosities are drawn, and it is concluded that the Young’s modulus and strength limit decrease with the increase of nanoporosity.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Mechanical Properties of Pyrolytic "SiOCN" Thin Coatings

1993 ◽  
Vol 308 ◽  
Author(s):  
Sandrine Bec ◽  
André Tonck ◽  
Jean-Luc Loubet
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Coatings ◽  
Optical Observation ◽  
Thin Coatings ◽  
Polymer Precursors ◽  
Polymeric State

ABSTRACTPyrolysis of polymer precursors (polysilazane) is a technologically and economically interesting way to produce thin ceramic coatings. However, many cracks appear and decohesion occurs during pyrolysis when the ceramic coatings (SiOCN) are thicker than 0.5 micrometers. In order to understand these cracking phenomena, the coatings are mechanically characterized by nanoindentation at different stages of the pyrolysis heat treatment.During pyrolysis, the cracking temperature is detected by in-situ optical observation. The thickness of the coatings varies during pyrolysis from 3 micrometers at the polymeric state to 1 micrometer at the ceramic state. The coatings' properties, hardness and Young's modulus are evaluated after heat treatment, taking into account the substrate's influence. A large variation of these properties occurs at the cracking temperature. Both the hardness and the Young's modulus are multiplied by a factor of 10. By analysing these results, we show that cracking is correlated with the evolution of the coatings' mechanical properties during the transformation.

scholarly journals Atomic Simulations of Packing Structures, Local Stress and Mechanical Properties for One Silicon Lattice with Single Vacancy on Heating

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3127
Author(s):  
Feng Dai ◽  
Dandan Zhao ◽  
Lin Zhang
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Silicon Crystal ◽  
Local Stress ◽  
Uniaxial Tensile ◽  
Single Vacancy ◽  
Vacancy Defects ◽  
Silicon Lattice ◽  
Atomic Simulations

The effect of vacancy defects on the structure and mechanical properties of semiconductor silicon materials is of great significance to the development of novel microelectronic materials and the processes of semiconductor sensors. In this paper, molecular dynamics is used to simulate the atomic packing structure, local stress evolution and mechanical properties of a perfect lattice and silicon crystal with a single vacancy defect on heating. In addition, their influences on the change in Young’s modulus are also analyzed. The atomic simulations show that in the lower temperature range, the existence of vacancy defects reduces the Young’s modulus of the silicon lattice. With the increase in temperature, the local stress distribution of the atoms in the lattice changes due to the migration of the vacancy. At high temperatures, the Young’s modulus of the silicon lattice changes in anisotropic patterns. For the lattice with the vacancy, when the temperature is higher than 1500 K, the number and degree of distortion in the lattice increase significantly, the obvious single vacancy and its adjacent atoms contracting inward structure disappears and the defects in the lattice present complex patterns. By applying uniaxial tensile force, it can be found that the temperature has a significant effect on the elasticity–plasticity behaviors of the Si lattice with the vacancy.

Sign in / Sign up

Export Citation Format

Share Document