A Numerical Study of Stress Controlled Surface Diffusion During Epitaxial Film Growth

1994 ◽  
Vol 356 ◽  
Author(s):  
Cheng-Hsin Chiu ◽  
Huajian Gao
Keyword(s):  
Surface Diffusion ◽  
Film Growth ◽  
Numerical Study ◽  
Morphological Evolution ◽  
Film Surface ◽  
Numerical Results ◽  
Simultaneous Action ◽  
Surface Evolution ◽  
Growth Modes ◽  
Film Substrate

AbstractA two-dimensional numerical simulation is performed to model the morphological evolution of a strained film growing heteroepitaxially on a substrate under simultaneous action of vapor deposition and surface diffusion. To facilitate numerical implementation, a continuum boundary layer model is proposed to account for the influence of film/substrate interface on the film growth pattern. Discussions are focused on the Stranski-Krastanow growth mode, although our model is capable of explaining Frank-van der Merwe and Volmer-Weber growth modes as well. Both first-order perturbation and numerical results are developed to demonstrate that the film surface tends to remain flat during the initial stage of growth and that surface roughening occurs once the film thickness exceeds a critical value, in consistency with experimentally observed patterns of S-K growth. Numerical results further show that, depending on the deposition rate, the surface evolution could lead to a steady state morphology, unstable cusp formation, or growing islands with flattened valleys.

Modeling the sloshing problem in a rectangular tank with submerged incomplete baffles

2016 ◽  
Vol 26 (3/4) ◽  
pp. 722-744 ◽  
Author(s):  
Marcela A. Cruchaga ◽  
Carlos Ferrada ◽  
Nicolás Márquez ◽  
Sebastián Osses ◽  
Mario Storti ◽  
...  
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Wave Height ◽  
Numerical Study ◽  
Free Surface Flows ◽  
Numerical Results ◽  
Surface Evolution ◽  
Content Type ◽  
Near Resonance ◽  
Wave Heights

Purpose – The present work is an experimental and numerical study of a sloshing problem including baffle effects. The purpose of this paper is to assess the numerical behavior of a Lagrangian technique to track free surface flows by comparison with experiments, to report experimental data for sloshing at different conditions and to evaluate the effectiveness of baffles in limiting the wave height and the wave propagation. Design/methodology/approach – Finite element simulations performed with a fixed mesh technique able to describe the free surface evolution are contrasted with experimental data. The experiments consist of an acrylic tank of rectangular section designed to attach baffles of different sizes at different distance from the bottom. The tank is filled with water and mounted on a shake table able to move under controlled horizontal motion. The free surface evolution is measured with ultrasonic sensors. The numerical results computed for different sloshing conditions are compared with the experimental data. Findings – The reported numerical results are in general in good agreement with the experiments. In particular, wave heights and frequencies response satisfactorily compared with the experimental data for the several cases analyzed during steady state forced sloshing and free sloshing. The effectiveness of the baffles increases near resonance conditions. From the set of experiments studied, the major reduction of the wave height was obtained when larger baffles were positioned closer to the water level at rest. Practical implications – Model validation: evaluation of the effectiveness of non-massive immersed baffles during sloshing. Originality/value – The value of the present work encompass the numerical and experimental study of the effect of immersed baffles during sloshing under different imposed conditions and the comparison of numerical results with the experimental data. Also, the results shown in the present work are a contribution to the understanding of the role in the analysis of the proposed problem of some specific aspects of the geometry and the imposed motion.

Numerical Simulation of Diffusion Controlled Surface Evolution

1993 ◽  
Vol 317 ◽  
Author(s):  
Cheng-Hsin Chiu ◽  
Huajian Gao
Keyword(s):  
Numerical Simulation ◽  
Numerical Methods ◽  
Diffusion Process ◽  
Surface Diffusion ◽  
Morphological Evolution ◽  
Two Dimensional ◽  
Lateral Direction ◽  
Surface Evolution ◽  
Diffusion Controlled ◽  
Heteroepitaxial Layers

ABSTRACTAs a model for Stranski-Krastanow island formation in strained heteroepitaxial layers, this paper investigates the surface-diffusion controlled morphological evolution of a two dimensional semi-infinite solid loaded in the lateral direction. Numerical Methods are developed to simulate the surface diffusion process, and examples are presented to demonstrate three distinct evolution patterns which are characterized by two critical wavelengths. The results show that, according to the wavelength, a slightly wavy surface can evolve into a cusped, a smoothly undulating, or a flat configuration. The diffusion wavelength and cusp-formation time compare favorably with recent experimental observations.

Parallel Glide: A Fundamentally Different Type of Dislocation Motion in Ultrathin Metal Films

2003 ◽  
Vol 779 ◽  
Author(s):  
T. John Balk ◽  
Gerhard Dehm ◽  
Eduard Arzt
Keyword(s):  
Thermal Cycling ◽  
Grain Boundaries ◽  
Film Surface ◽  
Metal Films ◽  
Geometric Constraints ◽  
Film Stress ◽  
Diffusional Creep ◽  
Creep Model ◽  
Substrate Interface ◽  
Film Substrate

AbstractWhen confronted by severe geometric constraints, dislocations may respond in unforeseen ways. One example of such unexpected behavior is parallel glide in unpassivated, ultrathin (200 nm and thinner) metal films. This involves the glide of dislocations parallel to and very near the film/substrate interface, following their emission from grain boundaries. In situ transmission electron microscopy reveals that this mechanism dominates the thermomechanical behavior of ultrathin, unpassivated copper films. However, according to Schmid's law, the biaxial film stress that evolves during thermal cycling does not generate a resolved shear stress parallel to the film/substrate interface and therefore should not drive such motion. Instead, it is proposed that the observed dislocations are generated as a result of atomic diffusion into the grain boundaries. This provides experimental support for the constrained diffusional creep model of Gao et al.[1], in which they described the diffusional exchange of atoms between the unpassivated film surface and grain boundaries at high temperatures, a process that can locally relax the film stress near those boundaries. In the grains where it is observed, parallel glide can account for the plastic strain generated within a film during thermal cycling. One feature of this mechanism at the nanoscale is that, as grain size decreases, eventually a single dislocation suffices to mediate plasticity in an entire grain during thermal cycling. Parallel glide is a new example of the interactions between dislocations and the surface/interface, which are likely to increase in importance during the persistent miniaturization of thin film geometries.

Using Ansys for Design and Numerical Study of a Specific Fixed Wing UAV

2018 ◽  
Vol 55 (4) ◽  
pp. 652-657 ◽  
Author(s):  
Gabriel Murariu ◽  
Razvan Adrian Mahu ◽  
Adrian Gabriel Murariu ◽  
Mihai Daniel Dragu ◽  
Lucian P. Georgescu ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Unmanned Aerial Vehicle ◽  
Numerical Study ◽  
Flight Time ◽  
Cluster System ◽  
Numerical Results ◽  
Operational Performance ◽  
Gliding Flight ◽  
Aerial Vehicle ◽  
Constant Altitude

This article presents the design of a specific unmanned aerial vehicle UAV prototype own building. Our UAV is a flying wing type and is able to take off with a little boost. This system happily combines some major advantages taken from planes namely the ability to fly horizontal, at a constant altitude and of course, the great advantage of a long flight-time. The aerodynamic models presented in this paper are optimized to improve the operational performance of this aerial vehicle, especially in terms of stability and the possibility of a long gliding flight-time. Both aspects are very important for the increasing of the goals� efficiency and for the getting work jobs. The presented simulations were obtained using ANSYS 13 installed on our university� cluster system. In a next step the numerical results will be compared with those during experimental flights. This paper presents the main results obtained from numerical simulations and the obtained magnitudes of the main flight coefficients.

Atomic Layer Deposition of Chalcogenides for Next-Generation Phase Change Memory

2021 ◽  
Author(s):  
Yoon Kyeung Lee ◽  
Chanyoung Yoo ◽  
Woohyun Kim ◽  
Jeongwoo Jeon ◽  
Cheol Seong Hwang
Keyword(s):  
Thin Film ◽  
Atomic Layer Deposition ◽  
Film Growth ◽  
Phase Change Memory ◽  
Film Surface ◽  
Atomic Layer ◽  
Thin Film Growth ◽  
Growth Technique ◽  
Layer Deposition ◽  
Change Memory

Atomic layer deposition (ALD) is a thin film growth technique that uses self-limiting, sequential reactions localized at the growing film surface. It guarantees exceptional conformality on high-aspect-ratio structures and controllability...

Preparation of Large Area Cross-Sectional Tem Specimen of Semiconducting Heteroepitaxial Materials

1991 ◽  
Vol 254 ◽  
Author(s):  
M. Tamura ◽  
S. Aoki
Keyword(s):  
Sample Preparation ◽  
Film Growth ◽  
General Information ◽  
One Dimension ◽  
Main Principle ◽  
Large Area ◽  
Cross Sectional ◽  
Growth Modes ◽  
Present Technique ◽  
Grinding And Polishing

AbstractThe sample preparation procedures which enable us to observe large areas over a few tens of microns in one-dimension of semiconducting heteroepitaxial materials are described. The main principle involves the careful grinding and polishing of samples. In these procedures, another side thinning of the specimen after finishing initial side polishing is carried out using a sample platform by hand throughout all of the following steps. It is shown that for some typical examples of heteroepitaxial films general information concerning the film growth modes and structures, as well as the defect morphologies and natures introduced during growth can be effectively obtained by using the present technique.

Experimental and Numerical Study on Grinding Temperature during Surface Grinding with Different Cooling Methods

2009 ◽  
Vol 416 ◽  
pp. 514-518 ◽  
Author(s):  
Qing Long An ◽  
Yu Can Fu ◽  
Jiu Hua Xu
Keyword(s):  
Numerical Study ◽  
Specific Energy Consumption ◽  
Ground Surface ◽  
Numerical Results ◽  
Surface Grinding ◽  
Grinding Temperature ◽  
Air Jet ◽  
The Difference ◽  
High Specific Energy ◽  
Cooling Methods

Grinding, characterized by its high specific energy consumption, may generate high grinding zone temperature. These can cause thermal damage to the ground surface and poor surface integrity, especially in the grinding of difficult-to-machine materials. In this paper, experimental and fem study on grinding temperature during surface grinding of Ti-6Al-4V with different cooling methods. A comparison between the experimental and numerical results is made. It is indicated that the difference between experimental and numerical results is below 15% and the numerical results can be considered reliable. Grinding temperature can be more effectively reduced with CPMJ than that with cold air jet and flood cooling method.

Exotic Doping for Zno Thin Films: Possibility of Monolithic Optical Integrated Circuit

1999 ◽  
Vol 574 ◽  
Author(s):  
Norifumi Fujimura ◽  
Tamaki Shimura ◽  
Toshifumi Wakano ◽  
Atsushi Ashida ◽  
Taichiro Ito
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Nonlinear Optic ◽  
Integrated Circuit ◽  
Film Surface ◽  
Zno Thin Films ◽  
Process Window ◽  
Electro Optic ◽  
Film Substrate ◽  
Optical Integrated Circuit

AbstractWe propose the application of ZnO:X (X = Li, Mg, N, In, Al, Mn, Gd, Yb etc.) films for a monolithic Optical Integrated Circuit (OIC). Since ZnO exhibits excellent piezoelectric effect and has also electro-optic and nonlinear optic effects and the thin films are easily obtained, it has been studied as one of the important thin film wave guide materials especially for an acoustooptic device[1]. In terms of electro-optic and nonlinear optic effects, however, LiNbO3 or LiTaO3 is superior to ZnO. The most important issue of thin film waveguide using such ferroelectrics is optical losses at the film/substrate interface and the film surface, because the process window to control the surface morphology is very narrow due to their high deposition temperature. Since ZnO can be grown at extremely low temperature, the roughness at the surface and the interface is expected to be minimized. This is the absolute requirement especially for waveguide using a blue or ultraviolet laser. Recently, lasing at the wavelength of ultraviolet, ferroelectric and antiferromagnetic behaviors of ZnO doped with various exotic elements (exotic doping) have been reported. This paper discusses the OIC application of ZnO thin films doped with exotic elements.

Sign in / Sign up

Export Citation Format

Share Document