Mechanical Properties and Wear Resistance of High Moment thin Film Head Materials

1994 ◽  
Vol 356 ◽  
Author(s):  
H. Deng ◽  
V. R. Inturi ◽  
J. A. Barnard
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Wear Resistance ◽  
Magnetic Thin Films ◽  
Mechanical And Tribological Properties ◽  
Sputtered Films ◽  
Recording Heads ◽  
High Density Recording ◽  
Worn Surface

AbstractMechanical and tribological properties of soft magnetic thin films with high permeability and low coercivity are very important for the application of these films in high-density recording heads. This paper reports our experimental observations on these important properties of FeTaN thin film head materials. Hardness(H) and Young’s modulus(E) for FeTaN sputtered films were determined by nanoindentation. Wear resistance of these films against commercial magnetic tapes was measured with a sphere-on-flat wear tester. The experimental results indicate that the FeTa films can be hardened when nitrogen is introduced. It was found in this study that the thermal stability of the mechanical properties such as hardness of thin films containing nitrogen is better than that of the film without nitrogen. However, our experiments also revealed that the wear resistance of FeTaN films decreases when the concentration of nitrogen increases and the hardness of the worn surface at a wear scar is lower than that of the unworn surface.

Performance characteristics of steel 1.2842 after nitridation

2021 ◽  
Vol 16 (1) ◽  
pp. 43-48
Author(s):  
Michal Krbaťa ◽  
◽  
Jana Escherová ◽  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Wear Resistance ◽  
Chemical Composition ◽  
Plasma Nitriding ◽  
Cutting Tools ◽  
Operating Costs ◽  
Mechanical And Tribological Properties ◽  
Structure Thickness ◽  
Pin On Disc

The paper deals with the change in mechanical properties and wear of 1.2842 universal tool steel after plasma nitriding, which is widely used to produce cutting tools with good durability and low operating costs. Plasma nitriding was performed at a temperature of 500 °C for 10-hour period in a standard N2 /H2 atmosphere with 1:3 gases ratio. Microstructure, phase structure, thickness of a nitriding layer and surface roughness of samples were measured with optical microscopes and a profilometer. Verification of a chemical composition was carried out on the BAS TASMAN Q4 device. Wear resistance was measured on a universal TRIBOLAB UTM 3 tribometer, through a, “pin on disc“ method. The results of experiments have shown that plasma nitriding process, significantly improves the mechanical and tribological properties of selected materials.

Mechanical deflection of cantilever microbeams: A new technique for testing the mechanical properties of thin films

1988 ◽  
Vol 3 (5) ◽  
pp. 931-942 ◽  
Author(s):  
T. P. Weihs ◽  
S. Hong ◽  
J. C. Bravman ◽  
W. D. Nix
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Single Layer ◽  
Beam Theory ◽  
New Technique ◽  
Young’S Moduli ◽  
Silicon Micromachining ◽  
A New Technique

The mechanical deflection of cantilever microbeams is presented as a new technique for testing the mechanical properties of thin films. Single-layer microbeams of Au and SiO2 have been fabricated using conventional silicon micromachining techniques. Typical thickness, width, and length dimensions of the beams are 1.0,20, and 30 μm, respectively. The beams are mechanically deflected by a Nanoindenter, a submicron indentation instrument that continuously monitors load and deflection. Using simple beam theory and the load-deflection data, the Young's moduli and the yield strengths of thin-film materials that comprise the beams are determined. The measured mechanical properties are compared to those obtained by indenting similar thin films supported by their substrate.

Mechanical and Tribological Properties of W(100-x)%Cx% Coatings Deposited by DC Magnetron Sputtering

2015 ◽  
Vol 642 ◽  
pp. 184-189
Author(s):  
Yan Liang Su ◽  
Yueh Feng Lin
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Magnetron Sputtering ◽  
X Ray Diffraction ◽  
Mechanical And Tribological Properties ◽  
Unbalanced Magnetron Sputtering ◽  
Unbalanced Magnetron ◽  
Pin On Disc ◽  
Dry Conditions ◽  
Coating Microstructure

W(100-x)%Cx% coatings with different tungsten and carbon contents were deposited by unbalanced magnetron sputtering. The microstructures and mechanical properties of the W(100-x)%C x% coatings was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), nanoindentation and adhesion testing techniques. The tribological performance of the coatings was investigated using a pin-on-disc trobometer under dry conditions. Experimental results indicated that coating microstructure, mechanical properties and wear resistance varied according to the tungsten and carbon contents of the coatings. The W72%C28% coating had the highest hardness/elastic modulus (H/E) ratio. In the ball-on-disc wear tests, it was found that the W72%C28% coating exhibited the best wear resistance.

Deposition energy dependence in cluster-assembled thin film densities

2005 ◽  
Vol 908 ◽  
Author(s):  
Kristoffer Meinander ◽  
Tina Clauss ◽  
Kai Nordlund
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Molecular Dynamics ◽  
Energy Dependence ◽  
Computer Simulations ◽  
Cluster Atom ◽  
Cu Nanoclusters ◽  
Deposition Energy

AbstractMechanical properties of thin films grown by nanocluster deposition are highly dependent on the energy at which the clusters are deposited. Using molecular dynamics computer simulations we have quantitatively studied variations in the properties of copper thin films grown by deposition of Cu nanoclusters, at energies ranging from 5 meV to 10 eV per cluster atom, on a Cu (100) substrate.

Thermal, mechanical, and tribological properties of short carbon fibers/PEEK composites

2017 ◽  
Vol 30 (6) ◽  
pp. 657-666 ◽  
Author(s):  
Fangfang Li ◽  
Ying Hu ◽  
Xiaochen Hou ◽  
Xiyu Hu ◽  
Dong Jiang
Keyword(s):  
Mechanical Properties ◽  
Carbon Fibers ◽  
Tribological Properties ◽  
Mechanical And Tribological Properties ◽  
Lower Viscosity ◽  
Ether Ether Ketone ◽  
Poly Ether Ether Ketone ◽  
The Coefficient Of Friction ◽  
Worn Surface ◽  
Short Carbon

In this work, the effect of thermal, mechanical, and tribological properties of the blending system of different contents of short carbon fibers (SCFs) on different-viscosity poly-ether-ether-ketone (PEEK) was reported. The composites were manufactured using injection molding technique. Mechanical and tribological properties were measured by the tensile strength, the flexural strength, the coefficient of friction, and the wear rate. The results showed that the wear resistance and mechanical properties of the PEEK with the lower viscosity appeared on a more outstanding level, and experimental results showed that PEEK composites with added 10 wt% SCFs were optimal about the tribological behaviors and mechanical properties of the composites. Furthermore, based on scanning electron microscope inspections, the situation of the friction and worn surface of the material was explained.

Characterization of Mechanical Properties of Thin Films by Nanoindentation Technique and Finite Element Simulation

2002 ◽  
Author(s):  
Zhaohui Shan ◽  
Suresh K. Sitaraman
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Finite Element ◽  
Strain Hardening Exponent ◽  
Plastic Properties ◽  
Titanium Thin Film ◽  
Nanoindentation Technique ◽  
Element Simulation ◽  
Titanium Thin Films

Titanium thin films have been widely used in microelectronics due to their good adhesion to substrates, such as Silicon wafer and Quartz. However, mechanical behavior of Titanium thin films has not been well characterized. This paper presents a methodology that combines the nanoindentation technique and finite element modeling to characterize the mechanical (elastic and plastic) properties of thin film with its application on Titanium thin film deposited on silicon substrate. The results show that the elastic properties (Young’s modulus) of the Titanium thin film does not change much from the bulk Titanium, and the plastic properties (yield stress and strain hardening exponent) of the Titanium thin film are higher than those of bulk Titanium. This method is also applicable for the study of mechanical properties of other thin films and small volume materials.

Analysis of the accuracy of the bulge test in determining the mechanical properties of thin films

1992 ◽  
Vol 7 (6) ◽  
pp. 1553-1563 ◽  
Author(s):  
Martha K. Small ◽  
W.D. Nix
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Finite Element ◽  
Material Properties ◽  
Deformation Behavior ◽  
Initial Conditions ◽  
Standard Technique ◽  
Bulge Test ◽  
The Finite Element Method

Since its first application to thin films in the 1950's the bulge test has become a standard technique for measuring thin film mechanical properties. While the apparatus required for the test is simple, interpretation of the data is not. Failure to recognize this fact has led to inconsistencies in the reported values of properties obtained using the bulge test. For this reason we have used the finite element method to model the deformation behavior of a thin film in a bulge test for a variety of initial conditions and material properties. In this paper we will review several of the existing models for describing the deformation behavior of a circular thin film in a bulge test, and then analyze these models in light of the finite element results. The product of this work is a set of equations and procedures for analyzing bulge test data that will improve the accuracy and reliability of this technique.

Cycling Times of Thin-Film NiTi on Si

1991 ◽  
Vol 246 ◽  
Author(s):  
A. Peter Jardine
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Response Times ◽  
Bulk Material ◽  
Fast Response ◽  
Promising Candidate ◽  
Strain Measurements ◽  
Micro Actuator ◽  
Acoustic Velocities

AbstractThe thermo-mechanical properties of NiTi are well known for bulk material although its deposition and utilization as a thin film are still in their earliest stages. The deposition of thin-films of Shape Memory Effect NiTi onto Si(100) wafers offers several advantages over bulk NiTi, including fast response times and comparitively large transformation forces, and so is a promising candidate as a micro-actuator for MicroElectroMechanical (MEMS) systems as well as in strain measurements. The response time for a variety of NiTi layers were modelled under different boundary conditions and show response times similar to the acoustic velocities for one micron thick NiTi.

scholarly journals A Direct Comparison of Three Buckling-Based Methods to Measure the Elastic Modulus of Nanobiocomposite Thin Films

2020 ◽  
Author(s):  
Taylor C. Stimpson ◽  
Daniel A. Osorio ◽  
Emily D. Cranston ◽  
Jose Moran-Mirabal
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Mechanical Properties ◽  
Elastic Modulus ◽  
Elastic Moduli ◽  
Input Parameter ◽  
Layer By Layer ◽  
Free Standing ◽  
Film Composition ◽  
Parameter Values

<p>To engineer tunable thin film materials, accurate measurement of their mechanical properties is crucial. However, characterizing the elastic modulus with current methods is particularly challenging for sub-micrometer thick films and hygroscopic materials because they are highly sensitive to environmental conditions and most methods require free-standing films which are difficult to prepare. In this work, we directly compared three buckling-based methods to determine the elastic moduli of supported thin films: 1) biaxial thermal shrinking, 2) uniaxial thermal shrinking, and 3) the mechanically compressed, strain-induced elastic buckling instability for mechanical measurements (SIEBIMM) method. Nanobiocomposite model films composed of cellulose nanocrystals (CNCs) and polyethyleneimine (PEI) were assembled using layer-by-layer deposition to control composition and thickness. The three buckling-based methods yielded the same trends and comparable values for the elastic moduli of each CNC-PEI film composition (ranging from 15 – 44 GPa, depending on film composition). This suggests that the methods are similarly effective for the quantification of thin film mechanical properties. Increasing the CNC content in the films statistically increased the modulus, however, increasing the PEI content did not lead to significant changes. The standard deviation of elastic moduli determined from SIEBIMM was 2-4 times larger than for thermal shrinking, likely due to extensive cracking and partial film delamination. In light of these results, biaxial thermal shrinking is recommended as the method of choice because it affords the simplest implementation and analysis and is the least sensitive to small deviations in the input parameter values, such as film thickness or substrate modulus.</p>

scholarly journals PHYSICAL AND MECHANICAL PROPERTIES OF MULTI-ELEMENT COATINGS

2021 ◽  
Vol 7 (2(38)) ◽  
pp. 31-32
Author(s):  
G. A. Zharmagambetova ◽  
I. A. Kudusova ◽  
V. Ch. Laurinas
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Wear Resistance ◽  
Friction And Wear ◽  
Physical And Mechanical Properties ◽  
Magnetron Deposition ◽  
Nickel Chromium ◽  
High Microhardness

A number of experiments were conducted to measure the physical and mechanical properties of multielement coatings. To apply CrNiTiFeCu coatings on a nickel-chromium substrate, the technology of magnetron deposition in an atmosphere of argon or nitrogen was used. The results of measurements of the microhardness as well as the coefficients of friction and wear resistance of the applied CrNiTiFeCu thin films are presented. The findings indicate that the studied samples show a high microhardness and wear resistance. Consequently, there is a possibility to extend the lifespan of mechanisms and machines parts.

Sign in / Sign up

Export Citation Format

Share Document