Strength and Ductility of Ni3Al Alloyed with Boron and Substitutional Elements

1994 ◽  
Vol 364 ◽  
Author(s):  
K. Ishikawa ◽  
K. Aoki ◽  
T. Masumoto
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Tensile Test ◽  
Fracture Strength ◽  
Room Temperature ◽  
The Other ◽  
Other Hand ◽  
Strength And Ductility

AbstractThe effect of simultaneous alloying of boron (B) and the substitutional elements M on mechanical properties of Ni3Al was investigated by the tensile test at room temperature. The yield strength of Ni3Al+B increases by alloying with M except for Fe and Ga. In particular, it increases by alloying with Hf, Nb, W, Ta, Pd and Si. The fracture strength of Ni3Al+B increases by alloying with Pd, Ga, Si and Hf, but decreases with the other elements. Elongation of Ni3Al+B increases by alloying with Ga, Fe and Pd, but decreases with other elements. Hf and Pd is the effective element for the increase of the yield strength and the fracture strength of Ni3Al+B, respectively. Alloying with Hf leads to the increases of the yield strength and the fracture strength of Ni3Al+B, but to the lowering of elongation. On the other hand, alloying with Pd improves all mechanical properties, i.e. the yield strength, the fracture strength and elongation. On the contrary, alloying with Ti, V and Co leads to the lowering of mechanical properties of Ni3Al+B. The reason why ductility of Ni3Al+B is reduced by alloying with some elements M is discussed.

Effects of Zn on Mechanical Properties of MZK60 Wrought Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 391-394
Author(s):  
Ding Fei Zhang ◽  
Li Ping Ren ◽  
Hong Ju Zhang ◽  
Wei Yuang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Yield Strength ◽  
Tensile Test ◽  
Optical Microscopy ◽  
Magnesium Alloys ◽  
Room Temperature ◽  
Zn Addition ◽  
Zn Content

Developing new alloys and techniques is important for the applications of magnesium alloy products. The greatest challenge in the area is to exploit new wrought magnesium alloys[1]. In this paper, the effects of Zn addition on the microstructures and mechanical properties of the MZK60 wrought alloy which is modified from ZK60 have been investigated. The microstructures of these alloys at various states were evaluated by optical microscopy. The mechanical properties at room temperature of these alloys were studied systematically by tensile test. Experimental results indicated that increasing Zn content to 7~10%wt is able to get not only higher tensile strength and yield strength, but also higher elongation.

scholarly journals Kekuatan Tarik Paduan Al 2024-T3 Dan Al 2524-T3 Yang Telah Mengalami Proses Stretching, Chemical Milling Dan Shot Peening

2020 ◽  
Vol 5 (2) ◽  
pp. 129-133
Author(s):  
Yovial Mahyoedin ◽  
Jamasri Jamasri ◽  
Wenny Marthiana ◽  
Duskiardi Duskiardi ◽  
Rizky Arman
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Yield Stress ◽  
Shot Peening ◽  
Milling Process ◽  
The Other ◽  
Other Hand ◽  
Chemical Milling ◽  
Stretching Process ◽  
Al 2024

AbstrakPenelitian ini bertujuan untuk mengetahui perilaku uji tarik produk Al 2524-T3 dan Al 2024-T3 yang mengalami proses peregangan, chemical milling dan shot peening. Paduan ini diregangkan melebihi tegangan yeildnya masing-masing 1%, 3% dan 5%, kemudian dilakukan proses chemical milling satu sisi. Etsa yang digunakan dalam proses milling kimia adalah larutan NaOH + Na2S + H2O dengan konsentrasi tertentu. Pada permukaan dilakukan proses shot peening dengan variasi intensitas masing-masing 0,03 A, 0,05 A dan 0,07 A. Material tersebut kemudian diuji sifat mekaniknya dengan uji tarik. Hasil penelitian menunjukkan bahwa tegangan ultimate dan tegangan yield material meningkat dengan meningkatnya persentase regangan. Namun, perpanjangan juga meningkat yang menunjukkan bahwa proses peregangan justru meningkatkan keuletan. Di sisi lain, proses shot peening menurunkan elongasi yang mengindikasikan bahwa proses shot peening menyebabkan penurunan keuletan material. Kata kunci: pengujian tarik, chemical milling, shot peening, stretchingAbstractThis study aims to investigate the tensile test behaviour of Al 2524-T3 and Al 2024-T3 product, which undergoes stretching, chemical milling and shot peening processes. These alloys were stretched beyond yield stress, namely 1%, 3% and 5% of each, and then performed chemical milling process of one side. The etching used in chemical milling process were NaOH+Na2S+H2O solutions with certain concentration. The surface was performed shot peening process with varying intensity of 0.03 A, 0.05 A and 0.07 A respectively. The material then tested its mechanical properties by tensile test. The results show that ultimate and yield stress of material increases with the increase of stretching percentage. However, the elongation has also increased which indicates that stretching process actually increases the ductility. On the other hand, the shot peening process decreases the elongation which indicates that the shot peening process causes a reduction in the ductility of the material.  Keywords: tensile tes, chemical milling, shot peening, stretching

scholarly journals Effects of Substitution of Y with Yb and Ce on the Microstructures and Mechanical Properties of Mg88.5Zn5Y6.5

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 31
Author(s):  
Hongxin Liao ◽  
Taekyung Lee ◽  
Jiangfeng Song ◽  
Jonghyun Kim ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Creep Resistance ◽  
Room Temperature ◽  
High Thermal Stability ◽  
Long Period ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg88.5Zn5Y6.5-XREX (RE = Yb and Ce, X = 0, 1.5, 3.0, and 4.5) (wt.%) alloys were investigated in the present study. Mg88.5Zn5Y6.5 is composed of three phases, namely, α-Mg, long-period stacking ordered (LPSO) phases, and intermetallic compounds. The content of the LPSO phases decreased with the addition of Ce and Yb, and no LPSO phases were detected in Mg88.5Zn5Y2.0Yb4.5. The alloys containing the LPSO phases possessed a stratified microstructure and exhibited excellent mechanical properties. Mg88.5Zn5Y5.0Ce1.5 exhibited the highest creep resistance and mechanical strength at both room temperature and 200 °C, owing to its suitable microstructure and high thermal stability. The yield strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature was 358 MPa. The ultimate tensile strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature and 200 °C was 453 MPa and 360 MPa, respectively.

Effect of Small Iron, Chromium and Boron Additions as Alloying Elements on Microstructure and Mechanical Properties of Ni3Al

2007 ◽  
Vol 23 ◽  
pp. 123-126
Author(s):  
Radu L. Orban ◽  
Mariana Lucaci
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Alloying Elements ◽  
Alloyed Powder ◽  
Mechanically Alloyed ◽  
Powder Mixtures ◽  
B Additions ◽  
Strength And Ductility ◽  
Iron Chromium

This paper investigates the effect of Fe, Cr and B additions, in small proportions, as alloying elements in Ni3Al with the purpose to reduce its intrinsic fragility and extrinsic embrittlement and to enhance, in the same time, its mechanical properties. It represents a development of some previous research works of the authors, proving that Ni3Al-Fe-Cr-B alloys obtained by reactive synthesis (SHS) starting from Mechanically Alloyed powder mixtures have superior both room temperature tensile strength and ductility, and compression ones at temperatures up to 800 °C, than pure Ni3Al. These create premises for their using as superalloys substitutes.

Effect of Minor Additives on First Stage Graphitisation in White Cast Iron

1984 ◽  
Vol 34 ◽  
Author(s):  
P. L. Roy ◽  
A. K. Chakrabart ◽  
P. Banerjee
Keyword(s):  
Mechanical Properties ◽  
Cast Iron ◽  
Sodium Chloride ◽  
Yield Strength ◽  
White Cast Iron ◽  
Elemental Sulphur ◽  
Optimum Dose ◽  
White Iron ◽  
Kinetics Of ◽  
Strength And Ductility

ABSTRACTMinor additions (0.05-0.2 wt.%) of sodium chloride, hexachloroethane and elemental sulphur to commercial white iron melts have been found to enhance the kinetics of first stage graphitisation during subsequent annealing of white iron samples. The optimum dose of sodium chloride and hexachloroethane addition is around 0.1%. Yield strength and ductility of annealed test bars treated with NaCl or C2Cl6 compare favourably with those of untreated test bars. Sulphur treatment causes slight deterioration in mechanical properties. Fully grown nodules in both treated and untreated samples appear porous under SEM. Possible mechanisms of acceleration of graphitisation in the treated samples have been suggested.

scholarly journals Synthesis of spiro[dihydropyridine-oxindoles] via three-component reaction of arylamine, isatin and cyclopentane-1,3-dione

2013 ◽  
Vol 9 ◽  
pp. 8-14 ◽  
Author(s):  
Yan Sun ◽  
Jing Sun ◽  
Chao-Guo Yan
Keyword(s):  
Acetic Acid ◽  
Reaction Mechanism ◽  
Room Temperature ◽  
The Other ◽  
Other Hand ◽  
Three Component Reaction ◽  
High Yields

A fast and convenient protocol for the synthesis of novel spiro[dihydropyridine-oxindole] derivatives in satisfactory yields was developed by the three-component reactions of arylamine, isatin and cyclopentane-1,3-dione in acetic acid at room temperature. On the other hand the condensation of isatin with two equivalents of cyclopentane-1,3-dione gave 3,3-bis(2-hydroxy-5-oxo-cyclopent-1-enyl)oxindole in high yields. The reaction mechanism and substrate scope of this novel reaction is briefly discussed.

Diversification of α–Ketoamides via Transamidation Reactions with Alkyl and Benzyl Amines at Room Temperature

2021 ◽  
Author(s):  
Shweta Singh ◽  
Sureshbabu Popuri ◽  
Qazi Mohammad Junaid ◽  
Sabiah Shahul Hameed ◽  
Jeyakumar Kandasamy
Keyword(s):  
Room Temperature ◽  
The Other ◽  
Alkyl Amines ◽  
Other Hand ◽  
Wide Range

A wide range of N-tosyl α–ketoamides underwent transamidation with various alkyl amines in the absence of catalyst, base, or additives. On the other hand, transamidation in N-Boc α–ketoamides is achieved...

Mechanical And Superconducting Properties Of Cu-Nb3Sn In Situ Produced Composite Wires

1981 ◽  
Vol 12 ◽  
Author(s):  
A. Kolb-Telieps ◽  
B.L. Mordike ◽  
M. Mrowiec
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Wide Temperature Range ◽  
Volume Fraction ◽  
Superconducting Properties ◽  
Temperature Range ◽  
Composite Wires ◽  
Strength And Ductility

ABSTRACTCu-Nb composite wires were produced from powder, electrolytically coated with tin and annealed to convert the Nb fibres to Nb 3Sn. The content was varied between 10 wt % and 40 wt %. The superconducting properties of the wires were determined. The mechanical properties, tensile strength, yield strength and ductility were measured as a function of volume fraction and deformation over a wide temperature range. The results are compared with those for wires produced by different techniques.

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

Morphology and mechanical properties of transcrystalline isotactic polypropylene

e-Polymers ◽  
2003 ◽  
Vol 3 (1) ◽  
Author(s):  
Koh-hei Nitta ◽  
Yoshikazu Yamamoto
Keyword(s):  
Mechanical Properties ◽  
Isotactic Polypropylene ◽  
Mechanical Energy ◽  
Supermolecular Structure ◽  
The Other ◽  
Morphological Properties ◽  
Spherulitic Morphology ◽  
Other Hand ◽  
Morphology And Mechanical Properties ◽  
Yielding Process

Abstract We examined mechanical and morphological properties of fully transcrystalline polypropylene grown from the surface of poly(tetrafluoroethylene) sheets. Comparison of mechanical properties between transcrystalline and spherulitic polypropylenes demonstrated that Young’s modulus is dependent on the crystallinity and independent of the supermolecular structure. On the other hand, the mechanical yielding process was predominantly affected by the supermolecular structure, and the mechanical energy required for yielding of transcrystalline sheets was greater than that of the spherulitic morphology. In addition, it was found that mechanical necking is required for the alignment of lamellae in the stretching direction. This means that the unfolding process of lamellae orienting in the stretching direction is associated with necking and ductility.

Sign in / Sign up

Export Citation Format

Share Document