Fabrication and Characterization of TiNi/AL Smart Composites

2003 ◽  
Vol 785 ◽  
Author(s):  
Gyu Chang Lee ◽  
Jun Hee. Lee ◽  
Young Chul Park
Keyword(s):  
Composite Material ◽  
Shape Memory ◽  
Yield Stress ◽  
Room Temperature ◽  
Volume Fraction ◽  
Matrix Material ◽  
Al Alloy ◽  
Alloy Matrix ◽  
Strain Behavior ◽  
The Matrix

ABSTRACTAn attempt was made to fabricate composite material of an Al alloy matrix reinforced by TiNi shape memory fiber using a hot-press method and to investigate its microstructures and mechanical properties. The analysis of SEM and EDS showed that the composite material had good interface bonding. The stress-strain behavior of the composite material was evaluated at room temperature and 363 K as a function of pre-strain, and it showed that the yield stress at 363 K is higher than that at room temperature. It is also found that the yield stress of the composite material increased with increasing the amount of pre-strain and depended on the volume fraction of the fiber and heat treatment. The smartness of the composite could be given due to the shape memory effect of the TiNi fiber, which generated compressive residual stress in the matrix material when heated after being pre-strained. Microstructural observation revealed that interfacial reactions occurred between the matrix and fiber, creating two intermetallic layers.

Characristics of Shape Memory Composites Combined with Shape Memory Alloy and Shape Memory Polymer

2013 ◽  
Vol 705 ◽  
pp. 169-172
Author(s):  
Xue Feng ◽  
Li Min Zhao ◽  
Xu Jun Mi
Keyword(s):  
Shape Memory ◽  
Room Temperature ◽  
Shape Recovery ◽  
Volume Fraction ◽  
Shape Memory Polymer ◽  
Young Modulus ◽  
Thermomechanical Properties ◽  
The Matrix ◽  
Shape Memory Composites ◽  
Shape Fixity

In order to develop high functionality of shape memory materials, the shape memory composites combined with TiNi wire and shape memory epoxy were prepared, and the mechanical and thermomechanical properties were studied. The results showed the addition of TiNi wire increased the Young modulus and breaking strength both at room temperature and at elevated temperature. The composites maintained the rates of shape fixity and shape recovery close to 100%. The maximum recovery stress increased with increasing TiNi wire volume fraction, and obtained almost 3 times of the matrix by adding 1vol% TiNi wire.

Microstructures and Mechanical Properties of 6061 Al Matrix Smart Composite Containing TiNi Shape Memory Fiber

1996 ◽  
Vol 459 ◽  
Author(s):  
J. H. Lee ◽  
K. Hamada ◽  
K. Miziuuchia ◽  
M. Taya ◽  
K. Inoue
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Elevated Temperatures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Matrix Alloy ◽  
Flow Strength ◽  
The Matrix ◽  
Shape Memory Fiber ◽  
Al Matrix

ABSTRACT6061 Al-matrix composite with TiNi shape memory fiber as reinforcement has been fabricated by vacuum hot pressing to investigate the microstructure and mechanical properties. The yield stress of this composite increases with increasing amount of prestrain, and it also depends on the volume fraction of fiber and heat treatment. The smartness of the composite is given due to the shape memory effect of the TiNi fiber which generates compressive residual stresses in the matrix material when heated after being prestrained. Microstructual observations have revealed that interfacial reactions occur between the matrix and fiber, creating two intermetallic layers. The flow strength of the composite at elevated temperatures is significantly higher than that of the matrix alloy without TiNi fiber.

Constitutive Modeling of Near-Equiatomic NiTi Shape Memory Alloys Considering Composition and Heat Treatment

2016 ◽  
Vol 856 ◽  
pp. 78-84
Author(s):  
Austin Cox ◽  
Theocharis Baxevanis ◽  
Dimitris C. Lagoudas
Keyword(s):  
Heat Treatment ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Volume Fraction ◽  
Lattice Mismatch ◽  
Memory Performance ◽  
Matrix Material ◽  
Precipitate Growth ◽  
The Matrix ◽  
Niti Shape Memory Alloys

A predictive microscale-informed model that takes into account the precipitate–shape memory performance relations and allows for the evaluation of the effective thermomechanical response of precipitated Ni-rich NiTi shape memory alloys on the basis of composition and heat treatment is presented. The model considers the structural effect of the precipitates (coherency stresses due to the lattice mismatch between the precipitates and the matrix material and precipitate volume fraction), as well as the effect of the Ni-concentration gradient in the matrix, resulting from Ni-depletion during precipitate growth. The predictive capability of the model is tested against experimental data obtained fromNi50.7Ti (at. %) that has been heat treated under different conditions and good agreement is shown.

Fabrication of WS2-Dispersed Al Composite Material by Compression Shearing Method at Room Temperature

2014 ◽  
Vol 622-623 ◽  
pp. 1066-1074 ◽  
Author(s):  
Noboru Nakayama ◽  
Shota Sakagami ◽  
Masaomi Horita ◽  
Hiroyuki Miki ◽  
Ayaka Takahashi ◽  
...  
Keyword(s):  
Composite Material ◽  
Friction Coefficient ◽  
Room Temperature ◽  
Matrix Material ◽  
Aluminum Composite ◽  
Density Measurements ◽  
Al Composite ◽  
The Matrix ◽  
Free Material ◽  
Dispersed Aluminum

In this study, WS2-dispersed Al composite material was fabricated by Compression Shearing Method at Room Temperature, using various WS2content ratios. The mechanical and friction properties of the WS2-dispersed Al composites were measured. As a result, the density measurements showed that the compacted WS2-dispersed aluminum composite had a relative density of 95 to 99%. Tensile strength of WS2-dispersed Al has 200 MPa. The friction coefficient of Al/0.5vol.%WS2was 0.14, a reduction of 83%, in comparison with the 1.0 friction coefficient of the pure Al matrix material. The addition of WS2to the matrix systems used reduced the friction coefficient. Therefore, WS2-dispersed Al composite material is useful for maintenance-free material of slide member.

The Estimation of Thermal Conductivity for Alumina-Epoxy Composite Material with High Filling Volume Fraction

2014 ◽  
Vol 918 ◽  
pp. 21-26
Author(s):  
Chen Kang Huang ◽  
Yun Ching Leong
Keyword(s):  
Thermal Conductivity ◽  
Composite Material ◽  
Composite Materials ◽  
Physical Model ◽  
Electron Scattering ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
The Matrix ◽  
Transport Theorem ◽  
Good Agreement

In this study, the transport theorem of phonons and electrons is utilized to create a model to predict the thermal conductivity of composite materials. By observing or assuming the dopant displacement in the matrix, a physical model between dopant and matrix can be built, and the composite material can be divided into several regions. In each region, the phonon or electron scattering caused by boundaries, impurities, or U-processes was taken into account to calculate the thermal conductivity. The model is then used to predict the composite thermal conductivity for several composite materials. It shows a pretty good agreement with previous studies in literatures. Based on the model, some discussions about dopant size and volume fraction are also made.

Determination of fiber volume fraction in a cured laminate

2021 ◽  
pp. 002199832110112
Author(s):  
Qing Yang Steve Wu ◽  
Nan Zhang ◽  
Weng Heng Liew ◽  
Vincent Lim ◽  
Xiping Ni ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Volume Fraction ◽  
Evaluation Method ◽  
Volume Fraction ◽  
Matrix Material ◽  
Volume Ratio ◽  
Gravimetric Analysis ◽  
Fiber Volume ◽  
Laser Ultrasonic ◽  
The Matrix

Propagation of ultrasonic wave in Carbon Fiber Reinforced Polymer (CFRP) is greatly influenced by the material’s matrix, resins and fiber volume ratio. Laser ultrasonic broadband spectral technique has been demonstrated for porosity and fiber volume ratio extraction on unidirection aligned CFRP laminates. Porosity in the matrix materials can be calculated by longitudinal wave attenuation and accurate fiber volume ratio can be derived by combined velocity through the high strength carbon fiber and the matrix material with further consideration of porosity effects. The results have been benchmarked by pulse-echo ultrasonic tests, gas pycnometer and thermal gravimetric analysis (TGA). The potentials and advantages of the laser ultrasonic technique as a non-destructive evaluation method for CFRP carbon fiber volume fraction evaluation were demonstrated.

scholarly journals Particularities of structure formation of aluminum-copper composite materials manufactured by casting technology

2020 ◽  
pp. 116-121
Author(s):  
V. A. Kalinichenko ◽  
A. S. Kalinichenko ◽  
S. V. Grigoriev
Keyword(s):  
Composite Material ◽  
Composite Materials ◽  
Structure Formation ◽  
Matrix Material ◽  
Matrix Alloy ◽  
Alloying Elements ◽  
Casting Technology ◽  
The Matrix ◽  
Reinforcing Material ◽  
Copper Composite

To create friction pairs operating in severe working conditions, composite materials are now increasingly used. Composite materials obtained with the use of casting technologies are of interest due to the possibility to manufacture wide range of compositions at low price compared to powder metallurgy. Despite the fact that many composite materials have been sufficiently studied, it is of interest to develop new areas of application and give them the properties required by the consumer. In the present work the composite materials on the basis of silumin reinforced with copper granules were considered. Attention was paid to the interaction between the matrix alloy and the reinforcing phase material as determining the properties of the composite material. The analysis of distribution of the basic alloying elements in volume of composite material and also in zones of the interphases interaction is carried out. The analysis of the possibility of obtaining a strong interphase zone of contact between the reinforcing component and the matrix material without significant dissolution of the reinforcing material is carried out.

scholarly journals Functional Application for the Corn Leaf Fibre to Make Reinforced Polymer Composites Sheet

2021 ◽  
Author(s):  
Ramratan Guru ◽  
Anupam Kumar ◽  
Rohit Kumar
Keyword(s):  
Volume Fraction ◽  
Agricultural Waste ◽  
Matrix Material ◽  
Research Work ◽  
Weight Fraction ◽  
Natural Fibre ◽  
Raw Material ◽  
Corn Husk ◽  
The Matrix ◽  
Composite Product

This research work has mainly utilized agricultural waste material to make a good-quality composite sheet product of the profitable, pollution free, economical better for farmer and industries. In this study, from corn leaf fibre to reinforced epoxy composite product has been utilized with minimum 35 to maximum range 55% but according to earlier studies, pulp composite material was used in minimum 10 to maximum 27%. Natural fibre-based composites are under intensive study due to their light weight, eco-friendly nature and unique properties. Due to the continuous supply, easy of handling, safety and biodegradability, natural fibre is considered as better alternative in replacing many structural and non-structural components. Corn leaf fibre pulp can be new source of raw material to the industries and can be potential replacement for the expensive and non-renewable synthetic fibre. Corn leaf fibre as the filler material and epoxy as the matrix material were used by changing reinforcement weight fraction. Composites were prepared using hand lay-up techniques by maintaining constant fibre and matrix volume fraction. The sample of the composites thus fabricated was subjected to tensile, impact test for finding the effect of corn husk in different concentrations.

Physical and Mechanical Properties of Composites with Aluminum Alloy Matrix Designed for Metal Forming

2013 ◽  
Vol 212 ◽  
pp. 59-62 ◽  
Author(s):  
Jerzy Myalski ◽  
Jakub Wieczorek ◽  
Adam Płachta
Keyword(s):  
Mechanical Properties ◽  
Metal Forming ◽  
Matrix Material ◽  
Physical And Mechanical Properties ◽  
Mechanical Mixing ◽  
Alloy Matrix ◽  
Segregation Process ◽  
The Matrix ◽  
Glass Carbon ◽  
Properties Of Composites

The change of matrix and usage of the aluminum alloys designed for the metal forming in making the composite suspension allows to extend the processing possibility of this type of materials. The possibility of the metal forming of the composites obtained by mechanical mixing will extend the range of composite materials usage. Applying of the metal forming e.g. matrix forging, embossing, pressing or rolling, will allow to remove the incoherence of the structure created while casting and removing casting failures. In order to avoid the appearance of the casting failures the homogenization conditions need to be changed. Inserting the particles into the matrix influences on the shortening of the composite solidification. The type of the applied particles influenced the sedimentation process and reinforcement agglomeration in the structure of the composite. Opposite to the composites reinforced with one-phase particles applying the fasess mixture (glassy carbon and silicon carbide) triggered significant limitation in the segregation process while casting solidification. Inserting the particles into the AW-AlCu2SiMn matrix lowers the mechanical properties tension and impact value strength. The most beneficial mechanical properties were gained in case of heterofasess composites reinforced with the particle mixture of SiC and glass carbon. The chemical composition of the matrix material (AW-AlCu2SiMn) allows to increase additionally mechanical characteristics by the precipitation hardening reached through heat casting forming.

Interply Behavior Exhibited in Compliant Filamentary Composite Laminates

1982 ◽  
Vol 55 (4) ◽  
pp. 1078-1094 ◽  
Author(s):  
J. L. Turner ◽  
J. L. Ford
Keyword(s):  
Shear Strain ◽  
Composite Laminates ◽  
Matrix Material ◽  
Matrix Composites ◽  
Efficient Manner ◽  
Strain Behavior ◽  
The Matrix ◽  
Order Of Magnitude ◽  
Extensional Strain ◽  
Interlaminar Shear

Abstract Cord-rubber composite systems allow a visualization of interply shear strain effects because of the compliant nature of the matrix material. A technique termed the pin test was developed to aid this visualization of interply shear strain. The pin test performed on both flat pads and radial tires shows that interlaminar shear strain behavior in both types of specimens is similar, most of the shear strain being confined to a region approximately 10 interly rubber thicknesses from the edge. The observed shear strain is approximately an order of magnitude greater than the applied extensional strain. A simplified mathematical model, called the Kelsey strip, for describing such behavior for a two-ply (±θ) cord-rubber strip has been formulated and demonstrated to be qualitatively correct. Furthermore, this model is capable of predicting trends in both compliant and rigid matrix composites and allows for simplified idealizations. A finite-element code for dealing with such interply effects in a simple but efficient manner predicts qualitatively correct results.

Sign in / Sign up

Export Citation Format

Share Document