scholarly journals Factors and mass ratio analyses for Reactive Blue 19 dye decolorization using ozone: an experimental and analytical modelling approach

2019 ◽  
Vol 24 (3) ◽  
pp. 431-438
Author(s):  
Mayara Sakamoto Lopes ◽  
Rodrigo Braga Moruzzi ◽  
Fabiano Tomazini Conceição ◽  
Mariana Scicia Gabriel Silva ◽  
Maria Lucia Pereira Antunes
Keyword(s):  
Kinetic Studies ◽  
Dye Decolorization ◽  
Analytical Modelling ◽  
Mass Ratio ◽  
Pseudo First Order Reaction ◽  
Bulk Fluid ◽  
Reactive Blue 19 ◽  
Initial Ph ◽  
Power Law Equation ◽  
Modelling Approach

ABSTRACT Dyes highly reduce sunlight penetration into the stream, and consequently affect photosynthesis and oxygen transfer into water bodies. An experimental and analytical modelling approach to Reactive Blue 19 (RB19) removal using ozone was carried out. For this purpose, factors and mass ratio analyses were assessed based on batch assays experiments. Removal efficiency increased from 64 to 94% when the dosage increased from 38.4 to 153.6 mg O3.L-1. Results showed that RB19 is more efficiently removed when initial pH is 7. The rate of RB19 removal decreased as the initial dye concentration increased. Kinetic studies showed that the ozonation of RB19 was a pseudo first-order reaction with respect to the dye, and the apparent rate constant declined logarithmically with the initial dye concentration. Mass ratio studies showed that, for the empirical analysis, the power law equation was adequate to describe mass ratio over time and the analytical analysis suggests that the process is influenced by mass transfer in the liquid film as well as in the bulk fluid.

Chitosan-based Magnetic Composites - Efficient Adsorbents for Removal of Pb(II) and Cu(II) from Aqueous Mono and Bicomponent Solutions

2018 ◽  
Vol 69 (9) ◽  
pp. 2323-2330 ◽  
Author(s):  
Daniela C. Culita ◽  
Claudia Maria Simonescu ◽  
Rodica Elena Patescu ◽  
Nicolae Stanica
Keyword(s):  
Aqueous Solutions ◽  
Metal Ions ◽  
Chemical Properties ◽  
Order Kinetic ◽  
Mass Ratio ◽  
Magnetic Adsorbent ◽  
Magnetic Composites ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Physical And Chemical

A series of three chitosan-based magnetic composites was prepared through a simple coprecipitation method. It was investigated the influence of mass ratio between chitosan and magnetite on the physical and chemical properties of the composites in order to establish the optimum conditions for obtaining a composite with good adsorption capacity for Pb(II) and Cu(II) from mono and bicomponent aqueous solutions. It was found that the microspheres prepared using mass ratio chitosan / magnetite 1.25/1, having a saturation magnetization of 15 emu g--1, are the best to be used as adsorbent for the metal ions. The influence of different parameters such as initial pH values, contact time, initial concentration of metal ions, on the adsorption of Pb(II) and Cu(II) onto the chitosan-based magnetic adsorbent was investigated in details. The adsorption process fits the pseudo-second-order kinetic model in both mono and bicomponent systems, and the maximum adsorption capacities calculated on the basis of the Langmuir model were 79.4 mg g--1 for Pb(II) and 48.5 mg g--1 for Cu(II) in monocomponent systems, while in bicomponent systems were 88.3 and 49.5 mg g--1, respectively. The results revealed that the as prepared chitosan-based magnetic adsorbent can be an effective and promising adsorbent for Pb(II) and Cu(II) from mono and bicomponent aqueous solutions.

scholarly journals Reuse of Newspaper As An Adsorbent For Cu (II) Removal By Citric Acid Modification

2018 ◽  
Vol 156 ◽  
pp. 02012 ◽  
Author(s):  
Mardiah ◽  
Rif’an Fathoni ◽  
Pratiwi Pudyaningtyas ◽  
Hamdania Gamu ◽  
Rinaldy
Keyword(s):  
Citric Acid ◽  
Adsorption Process ◽  
Kinetic Studies ◽  
Order Reaction ◽  
Acid Modification ◽  
Pseudo First Order Reaction ◽  
First Order ◽  
Pseudo Second Order ◽  
Heavy Metal Adsorbent ◽  
The Impact

High Consumption of paper, bring the impact of the waste paper itself. And the utilization of the paper is limited to recycled products and crafts, whereas paper such as newspaper still contains cellulose that can be potential to be used as a heavy metal adsorbent. In this study, newspaper was dissolved in sodium bicarbonate to reduce various impurities and then was reacted with citric acid (CA). The modified adsorbent was characterized by FTIR and was tested for adsorb Cu(II) in artificial solution. After adsorption process, the solution was filtered and analysed using Atomic Absorption Spectrophotometer (AAS). The adsorption experimental data was fitted to Langmuir, Freundlich, Tempkin, and Dubinin-Radushkevich for equilibrium model and was fitted to pseudo first order reaction and pseudo second order reaction for kinetic studies. The result showed that CA-modification newspaper able to remove heavy metals Cu(II) in solution.

scholarly journals Degradation of Diallyl Phthalate (DAP) by Fenton Oxidation: Mechanistic and Kinetic Studies

2018 ◽  
Vol 9 (1) ◽  
pp. 23
Author(s):  
Sondos Dbira ◽  
Nasr Bensalah ◽  
Moustafa Zagho ◽  
Ahmed Bedoui
Keyword(s):  
High Performance ◽  
Hplc Analysis ◽  
Degradation Mechanism ◽  
Kinetic Studies ◽  
Cost Effective ◽  
Fenton Oxidation ◽  
Fenton’S Reaction ◽  
Toc Removal ◽  
Initial Ph ◽  
Diallyl Phthalate

In this work, the degradation and mineralization of Diallyl Phthalate (DAP) in water by Fenton oxidation was investigated. The effects of different experimental parameters including the initial pH, the hydrogen peroxide (H2O2) dose, the catalyst (Fe2+) dose, the iron source, and the DAP concentration on the rate and the yield of DAP degradation by Fenton oxidation were evaluated. DAP and its intermediates were quantified by high performance liquid chromatography (HPLC) analysis and the measurement of total organic carbon (TOC) during Fenton oxidation. The results obtained confirmed that hydroxyl radicals (HO•) generated from Fenton’s reaction were capable of completely eliminating DAP from water. Fenton oxidation of 100 mg/L DAP aqueous solution at pH = 3.2 required 1000 mg/L H2O2 and 50 mg/L Fe2+. Under these conditions, more than TOC removal exceeded 95% after 300 min Fenton oxidation. The competition kinetics method was used to determine an absolute rate constant of 7.26.109 M−1 s−1 for the reaction between DAP and HO• radicals. HPLC analysis showed that phthalic acid, 1,2-dihydroxybenzene, 1,2,4-trihydroxybenzene, maleic acid, formic acid and oxalic acid were the main intermediates formed during DAP degradation. Accordingly, a simple DAP degradation mechanism by the Fenton reaction was proposed. These promising results proved the potential of Fenton oxidation as a cost-effective method for the decontamination of wastewaters containing phthalates.

Synergetic Degradation of Zidovudine Wastewater by Ultrasonic and Iron-Carbon Micro-Electrolysis

2011 ◽  
Vol 347-353 ◽  
pp. 1949-1952 ◽  
Author(s):  
Liang Li ◽  
Bing Zhe Xu ◽  
Chang Yu Lin ◽  
Xiao Min Hu
Keyword(s):  
Reaction Time ◽  
Degradation Rate ◽  
Removal Rate ◽  
Cod Removal ◽  
Mass Ratio ◽  
Initial Ph ◽  
Cod Removal Rate

Zidovudine wastewater is difficult to biodegradation due to high COD and toxicity. The synergetic treatment of Zidovudine wastewater by Ultrasonic and iron-carbon micro-electrolysis technology was studied. The influence of initial pH, reaction time, mass ratio of iron and carbon and mass ratio of iron and water on degradation rate of COD was researched. The result showed that the COD removal rate was only about 54.3% and the degradation speed is very slow when iron-carbon micro-electrolysis treated Zidovudine wastewater　separately. However, when ultrasonic synergy micro-electrolysis to treat Zidovudine wastewater, the COD removal rate could was up to 85% and the reaction time was also decreased. Moreover, the BOD5 / COD rose from 0.15 to 0.35, which meant the wastewater became easily biodegradable.

scholarly journals The comparison of efficiency of Fenton and photo-Fenton treatment of stabilised landfill leachate / Porównanie efektywności oczyszczania odcieków z ustabilizowanego składowiska odpadów komunalnych w procesie Fentona i foto-Fentona

2015 ◽  
Vol 26 (3) ◽  
pp. 49-53 ◽  
Author(s):  
Anna Kwarciak-Kozłowska ◽  
Aleksandra Krzywicka
Keyword(s):  
Landfill Leachate ◽  
Fenton Reaction ◽  
Ferrous Sulphate ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Ammonia Removal ◽  
Mass Ratio ◽  
Leachate Treatment ◽  
Initial Ph ◽  
Removal Efficiencies

Abstract The goal of this article was to compare the efficiency of Fenton and photo-Fenton reaction used for stabilised landfill leachate treatment. The mass ratio of COD:H2O2 was fixed to 1:2 for every stages. The dose of reagents (ferrous sulphate/hydrogen peroxide) was different and ranged from 0.1 to 0.5. To determine the efficiency of treatment, the BOD (biochemical oxygen demand COD (chemical oxygen demand), TOC (total organic carbon) , ammonia nitrogen and BOD/COD ratio was measured. The experiment was carried out under the following conditions: temperature was 25ºC, the initial pH was adjusted to 3.0. Every processes were lasting 60 minutes. The most appropriate dose of reagents was 0.25 (Fe2+/H2O2). It was found that the application of UV contributed to increase of COD, TOC and ammonia removal efficiencies by an average of 14%.

scholarly journals Preparation of Chitosan Coated Magnetic Hydroxyapatite Nanoparticles and Application for Adsorption of Reactive Blue 19 and Ni2+Ions

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Van Cuong Nguyen ◽  
Quoc Hue Pho
Keyword(s):  
Removal Efficiency ◽  
Weight Percent ◽  
Textile Dye ◽  
Gravimetric Analysis ◽  
Hydroxyapatite Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Reactive Blue 19 ◽  
Adsorption Capacities ◽  
Initial Ph

An adsorbent called chitosan coated magnetic hydroxyapatite nanoparticles (CS-MHAP) was prepared with the purpose of improvement for the removal of Ni2+ions and textile dye by coprecipitation. Structure and properties of CS-MHAP were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometer (VSM). Weight percent of chitosan was investigated by thermal gravimetric analysis (TGA). The prepared CS-MHAP presents a significant improvement on the removal efficiency of Ni2+ions and reactive blue 19 dye (RB19) in comparison with chitosan and magnetic hydroxyapatite nanoparticles. Moreover, the adsorption capacities were affected by several parameters such as contact time, initial concentration, adsorbent dosage, and initial pH. Interestingly, the prepared adsorbent could be easily recycled from an aqueous solution by an external magnet and reused for adsorption with high removal efficiency.

Adsorptive removal of PPCPs by biomorphic HAP templated from cotton

2016 ◽  
Vol 74 (1) ◽  
pp. 276-286 ◽  
Author(s):  
Bin Huang ◽  
Dan Xiong ◽  
Tingting Zhao ◽  
Huan He ◽  
Xuejun Pan
Keyword(s):  
Adsorption Mechanism ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Precipitation Method ◽  
Adsorptive Removal ◽  
Transmission Electron ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Co Precipitation

Biomorphic nano-hydroxyapatite (HAP) was fabricated by a co-precipitation method using cotton as bio-templates and employed in adsorptive removal of ofloxacin (OFL) and triclosan (TCS) that are two representative pharmaceuticals and personal care products (PPCPs). The surface area and porosity, crystal phase, functional group, morphology and micro-structure of the synthesized HAP were characterized by Brunauer–Emmett–Teller isotherm, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron macroscopic and transmission electron microscopy. The effects of initial pH, ionic strength, initial concentration, contact time and temperature on the removal of PPCPs were studied in a batch experiment. The adsorption of OFL and TCS was rapid and almost accomplished within 50 min. Kinetic studies indicated that the adsorption process of OFL and TCS followed the pseudo-first-order and pseudo-second-order models, respectively. The Freundlich isotherm described the OFL adsorption process well but the adsorption of TCS fitted the Langmuir isotherm better. Thermodynamics and isotherm parameters suggested that both OFL and TCS adsorption were feasible and spontaneous. Hydrogen bond and Lewis acid–base reaction may be the dominating adsorption mechanism of OFL and TCS, respectively. Compared to other adsorbents, biomorphic HAP is environmentally friendly and has the advantages of high adsorption capacity, exhibiting potential application for PPCPs removal.

Degradation of bromamine acid by nanoscale zero-valent iron (nZVI) supported on sepiolite

2012 ◽  
Vol 66 (12) ◽  
pp. 2539-2545 ◽  
Author(s):  
Xuening Fei ◽  
Lingyun Cao ◽  
Lifeng Zhou ◽  
Yingchun Gu ◽  
Xiaoyang Wang
Keyword(s):  
Ph Value ◽  
Energy Dispersive Spectrometer ◽  
Zero Valent Iron ◽  
Mass Ratio ◽  
Initial Concentration ◽  
Preparation Conditions ◽  
Transmission Electron ◽  
Nanoscale Zero Valent Iron ◽  
Initial Ph ◽  
Set Up

Sepiolite, a natural nano-material, was chosen as a carrier to prepare supported nanoscale zero-valent iron (nZVI). The effects of preparation conditions, including mass ratio of nZVI and activated sepiolite and preparation pH value, on properties of the supported nZVI were investigated. The results showed that the optimal mass ratio of nZVI and sepiolite was 1.12:1 and the optimal pH value was 7. The supported nZVI was characterized by X-ray diffraction (XRD), transmission electron microscope (TEM) and energy dispersive spectrometer (EDS), and furthermore an analogy model of the supported nZVI was set up. Compared with the nZVI itself, the supported nZVI was more stable in air and possessed better water dispersibility, which were beneficial for the degradation of bromamine acid aqueous solution. The degradation characteristics, such as effects of supported nZVI dosage, initial concentration and initial pH value of the solution on the decolorization efficiency were also investigated. The results showed that in an acidic environment the supported nZVI with a dosage of 2 g/L showed high activity in the degradation of bromamine acid with an initial concentration of 1,000 mg/L, and the degree of decolorization could reach up to 98%.

scholarly journals Decolorization of Malachite green dye from wastewater by Populus deltoides: three-level Box–Behnken design optimization, equilibrium, and kinetic studies

2015 ◽  
Vol 5 (3) ◽  
pp. 250-263 ◽  
Author(s):  
Afsaneh Shahbazi ◽  
Farnoosh Bagheri Zonoz
Keyword(s):  
Malachite Green ◽  
Populus Deltoides ◽  
Kinetic Studies ◽  
Second Order ◽  
Coefficient Of Determination ◽  
P Value ◽  
Box Behnken Design ◽  
Malachite Green Dye ◽  
Initial Ph ◽  
Adsorbent Dose

Decolorization of Malachite green in aqueous solution by adsorption onto Populus deltoides sawdust (PSD) was optimized through a four-factor, three-level Box–Behnken design in response surface methodology. The influences of four independent variables such as initial pH of solution (3–7), dye concentration (50–300 mg/L), adsorbent dose (0.2–2 g/L), and temperature (23–50 °C) were studied to optimize the condition of dye removal. A natural log transformation was suggested by the Box–Cox plot in order to enhance the model significance. Regression analysis showed good fit of the experimental data to the second-order polynomial model with high coefficient of determination values (R2 = 0.996; Radj.2 = 0.9913; Rpred.2 = 0.9769), F-value of 213.03, and p-value of <0.0001 (α = 0.05). Under optimum values of all the four variables, viz., pH of 6.02, initial dye concentration of 262.6 mg/L, adsorbent dose of 0.23 g/L and temperature of 30.3 °C, the maximum uptake (qe) was noted to be 920.9 mg/g. The experimental equilibrium adsorption data were fitted well to the Langmuir isotherm model (R2 = 0.9949). Kinetic studies revealed that adsorption followed pseudo-second order. It was found that PSD is suitable for reuse four times in successive adsorption-desorption cycles with loss of 25.2% in adsorption capacity.

Sign in / Sign up

Export Citation Format

Share Document