scholarly journals Size effect on the methodology with cylinder specimens for FRP-to-concrete debonding analysis

2021 ◽  
Vol 14 (3) ◽  
Author(s):  
Luana Ferreira Borges ◽  
Antonio Carlos dos Santos
Keyword(s):  
Size Effect ◽  
Failure Modes ◽  
Tensile Force ◽  
Size Variation ◽  
Concrete Specimen ◽  
Three Dimensions ◽  
Tensile Failure ◽  
Interface Failure ◽  
Reinforced Polymer ◽  
Direct Tensile

Abstract This is a study about the size effect on the methodology with concrete cylinder specimens for analysis of the debonding phenomenon at the interface between concrete and carbon fiber reinforced polymer (FRP). The influence of the concrete specimen size variation is analyzed by maintaining the same geometry in adhered FRP. Direct tensile experiments were performed with three dimensions of cylindrical concrete specimens (diameter × height) for analysis of size effect: 50 mm × 100 mm, 100 mm × 200 mm, and 150 mm × 300 mm. Ten different geometries of the composite material were tested. Two failure modes were observed in the experiments: debonding between the two materials and tensile failure in concrete specimens. In experiments with interface failure, the size of concrete specimens has no significant influence on maximum force, shear stress to peak, and stiffness in debonding between concrete and FRP. However, the use of smaller specimens for analysis of interface collapse is limited because the concrete reaches its normal stress capacity with a lower tensile force, and therefore, the failure often occurs in the concrete.

Tensile behaviors of co-woven-knitted fabric reinforced composites under various strain rates

2011 ◽  
Vol 45 (24) ◽  
pp. 2495-2506 ◽  
Author(s):  
Pibo Ma ◽  
Hong Hu ◽  
Lvtao Zhu ◽  
Baozhong Sun ◽  
Bohong Gu
Keyword(s):  
Strain Rate ◽  
Failure Modes ◽  
Shear Failure ◽  
High Strain ◽  
Tensile Failure ◽  
Knitted Fabric ◽  
Strain Rates ◽  
High Strain Rates ◽  
Textile Composite ◽  
Interface Failure

This article reports the tensile behaviors of a novel kind of 3D textile composite, named as co-woven-knitted fabric (CWKF) reinforced composite, under quasi-static and high strain rates. The tensile tests were conducted along the warp direction (0°), bias direction (45°), and weft direction (90°) at quasi-static strain rate of 0.001/s and high strain rates ranging from 1589/s to 2586/s. The results indicate that the tensile strength, failure strain, tensile stiffness, energy absorption, and resilient energy are strain rate sensitive along all the three directions. The relationships between the mechanical parameters and the strain rate were also analyzed. The fractograph of the CWKF composite demonstrate that the tensile failure modes are matrix shear failure and fibers breakage under the quasi-static testing condition while interface failure and fibers pullout are at high strain rates.

Mesoscopic finite element analysis on dynamic direct tensile failure of lightweight aggregate concrete and corresponding size effect

2021 ◽  
pp. 105678952110441
Author(s):  
Wenxuan Yu ◽  
Liu Jin ◽  
Xi Liu ◽  
Xiuli Du
Keyword(s):  
Tensile Strength ◽  
Size Effect ◽  
Strain Rate ◽  
Lightweight Aggregate ◽  
Tensile Failure ◽  
Lightweight Aggregate Concrete ◽  
Element Analysis ◽  
Aggregate Concrete ◽  
Direct Tensile ◽  
Direct Tensile Strength

A comprehensive finite element analysis at the mesoscopic level has been conducted into the complex topic of size effect coupling dynamic strain-rates. Taking the lightweight aggregate concrete (LWAC) dumbbell-shaped samples as the object of numerical investigation, the influence of strain-rate (with the range of 10−5/s ∼ 100/s) on direct-tensile failure of LWAC (including different lightweight aggregate volume fractions [Formula: see text] = 40%, 30% and 20%) was discussed. Subsequently, the structure size of LWAC samples was further expanded (width W = 100, 200 and 300 mm) and the dynamic size effect on direct-tensile strength was investigated. Numerical results show that both the direct-tensile strength and its corresponding size effect of LWAC exhibit a strain-rate dependent behaviour. The increasing strain-rate can gradually weaken the size effect of LWAC and direct-tensile strength would be independent to the structure size as the strain-rate reaches the critical strain-rate. The increasing lightweight aggregate volume fraction can reduce direct-tensile strength. Furthermore, a dynamic size effect model establishing the direct link between the strain-rate effect and size effect was proposed, which can quantitatively predict the dynamic direct-tensile strength of LWAC.

scholarly journals Experimental Study of Coal Sample Damage in Acidic Water Environments

2021 ◽  
Author(s):  
Qiangling Yao ◽  
Chuanjin Tang ◽  
Ze Xia ◽  
Qiang Xu ◽  
Weinan Wang ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Failure Modes ◽  
Average Energy ◽  
Tensile Failure ◽  
Acidic Water ◽  
Unstable Crack ◽  
Physical Tests ◽  
Direct Tensile ◽  
Physical And Chemical ◽  
Sample Damage

AbstractWe investigated the effects of acidic and circumneutral water on coal samples by uniaxial compression, acoustic emission, and a series of physical tests. In acidic water, the coal samples were damaged, and their ultrasonic velocities decreased, as minerals such as kaolinite and calcite underwent dissolution. When the pH was < 7, the uniaxial compressive strength and elastic modulus decreased, while the duration of the residual strength stage tended to increase. The reactions were stronger at higher H+ concentrations and the number of large pores increased; there was a significant increase in the accumulated acoustic emission counts and maximum average energy near the unstable crack growth stage. The post-peak stage of the coal samples was characterized in the different acidic waters and the failure modes were identified by spectrum analysis. Acidic water damaged the weak areas of coal samples by complex physical and chemical reactions, which made direct tensile failure more likely when the coal samples were loaded.

scholarly journals Numerical Analysis of the Mechanical Behavior and Failure Mode of Jointed Rock under Uniaxial Tensile Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Yang Zhao ◽  
Yongning Wu ◽  
Qing Xu ◽  
Lishuai Jiang ◽  
Wanpeng Huang ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Failure Mode ◽  
Failure Modes ◽  
Tensile Tests ◽  
Jointed Rock ◽  
Rock Joints ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Direct Tensile ◽  
Rock Specimens

In the field of rock engineering, tensile failure is one of the most significant failure modes due to the presence of joints/fractures. However, due to the limitations of current laboratory testing, it is difficult to carry out direct tensile tests on jointed rock specimens in the laboratory. To study the effect of joints on the mechanical behavior and failure mode of jointed rock specimens, a three-point modeling method that can consider arbitrarily arranged rock joints is deduced and applied to discrete element simulation. The effects of different joint angles (the inclination angle α, rotation angle β, and superimposed angle γ of α and β, where γ is the angle between the joint and horizontal plane), the density (n), and the rate of cutting area (RCA) of the specimen loading surface (LSS) on the tensile strength (σt), elastic modulus in tension (Et), and failure mode of the specimens were analyzed. The results show that the joint angle (considering α, β, and γ) and RCA have a significant effect on the resulting σt and failure mode, while n has a significant effect on Et. The failure mode of the specimen changes from tensile failure along the joint to direct tensile failure of the specimen as γ increases, and the mechanical behavior transitions from unstable to stable. In addition, the main influence of γ on the mechanical behavior of specimens is revealed, and the change process of the failure mode after the cutting of the LSS is analyzed. The present research can be utilized for multiple purposes, including the joint development of surrounding rock and failure dominated by tensile failure in underground engineering, especially for tunnels, roadways, chambers, and so forth.

scholarly journals Experimental Study on the Mechanical Properties and Compression Size Effect of Recycled Aggregate Concrete

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2323
Author(s):  
Yubing Du ◽  
Zhiqing Zhao ◽  
Qiang Xiao ◽  
Feiting Shi ◽  
Jianming Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Size Effect ◽  
Compressive Stress ◽  
Failure Modes ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Substitution Ratio ◽  
The Impact

To explore the basic mechanical properties and size effects of recycled aggregate concrete (RAC) with different substitution ratios of coarse recycled concrete aggregates (CRCAs) to replace natural coarse aggregates (NCA), the failure modes and mechanical parameters of RAC under different loading conditions including compression, splitting tensile resistance and direct shear were compared and analyzed. The conclusions drawn are as follows: the failure mechanisms of concrete with different substitution ratios of CRCAs are similar; with the increase in substitution ratio, the peak compressive stress and peak tensile stress of RAC decrease gradually, the splitting limit displacement decreases, and the splitting tensile modulus slightly increases; with the increase in the concrete cube’s side length, the peak compressive stress of RAC declines gradually, but the integrity after compression is gradually improved; and the increase in the substitution ratio of the recycled aggregate reduces the impact of the size effect on the peak compressive stress of RAC. Furthermore, an influence equation of the coupling effect of the substitution ratio and size effect on the peak compressive stress of RAC was quantitatively established. The research results are of great significance for the engineering application of RAC and the strength selection of RAC structure design.

scholarly journals Stress–strain relationship model of glulam bamboo under axial loading

2020 ◽  
Vol 29 ◽  
pp. 2633366X2095872
Author(s):  
Yang Wei ◽  
Mengqian Zhou ◽  
Kunpeng Zhao ◽  
Kang Zhao ◽  
Guofen Li
Keyword(s):  
Tensile Stress ◽  
Compressive Stress ◽  
Failure Modes ◽  
Axial Loading ◽  
Tensile Failure ◽  
Stress Strain ◽  
Laminated Bamboo ◽  
Bamboo Scrimber ◽  
Strain Relationship ◽  
Strain Model

Glulam bamboo has been preliminarily explored for use as a structural building material, and its stress–strain model under axial loading has a fundamental role in the analysis of bamboo components. To study the tension and compression behaviour of glulam bamboo, the bamboo scrimber and laminated bamboo as two kinds of typical glulam bamboo materials were tested under axial loading. Their mechanical behaviour and failure modes were investigated. The results showed that the bamboo scrimber and laminated bamboo have similar failure modes. For tensile failure, bamboo fibres were ruptured with sawtooth failure surfaces shown as brittle failure; for compression failure, the two modes of compression are buckling and compression shear failure. The stress–strain relationship curves of the bamboo scrimber and laminated bamboo are also similar. The tensile stress–strain curves showed a linear relationship, and the compressive stress–strain curves can be divided into three stages: elastic, elastoplastic and post-yield. Based on the test results, the stress–strain model was proposed for glulam bamboo, in which a linear equation was used to describe the tensile stress–strain relationship and the Richard–Abbott model was employed to model the compressive stress–strain relationship. A comparison with the experimental results shows that the predicted results are in good agreement with the experimental curves.

Failure Analysis of Composite Structures Using Multiscale Technique

2020 ◽  
Vol 995 ◽  
pp. 209-213
Author(s):  
Young W. Kwon
Keyword(s):  
Composite Structures ◽  
Failure Modes ◽  
Cell Model ◽  
Fibrous Composite ◽  
Failure Criteria ◽  
Multiscale Approach ◽  
Interface Failure ◽  
Fiber Failure ◽  
Strain Rate Effects ◽  
Constituent Material

Failure analyses of laminated fibrous composite structures were conducted using the failure criteria based on a multiscale approach. The failure criteria used the stresses and strains in the fiber and matrix materials, respectively, rather than those smeared values at the lamina level. The failure modes and their respective failure criteria consist of fiber failure, matrix failure and their interface failure explicitly. In order to determine the stresses and strains at the constituent material level (i.e. fiber and matrix materials), analytical expressions were derived using a unit-cell model. This model was used for the multiscale approach for both upscaling and downscaling processes. The failure criteria are applicable to both quasi-static loading as well as dynamic loading with strain rate effects.

scholarly journals Tensile Behaviour of FRCM Composites for Strengthening of Masonry Structures—An Experimental Investigation

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3626
Author(s):  
Łukasz Hojdys ◽  
Piotr Krajewski
Keyword(s):  
Tensile Stress ◽  
Strain Curve ◽  
Tensile Tests ◽  
Tensile Failure ◽  
Tensile Behaviour ◽  
Masonry Structures ◽  
Stress Strain ◽  
Flexural Tensile Strength ◽  
Cracking Pattern ◽  
Direct Tensile

This paper presents the results of direct tensile tests performed on six different FRCM (fabric reinforced cementitious matrix) strengthening systems used for masonry structures. The emphasis was placed on the determination of the mechanical parameters of each tested system and a comparison of their tensile behaviour in terms of first crack stress, ultimate stress, ultimate strain, cracking pattern, failure mode and idealised tensile stress-strain curve. In addition to the basic mechanical tensile parameters, accidental load eccentricities, matrix tensile strengths, and matrix modules of elasticity were estimated. The results of the tests showed that the tensile behaviour of FRCM composites strongly depends on the parameters of the constituent materials (matrix and fabric). In the tests, tensile failure of reinforcement and fibre slippage within the matrix were observed. The presented research showed that the accidental eccentricities did not substantially affect the obtained results and that the more slender the specimen used, the more consistent the obtained results. The analysis based on a rule of mixtures showed that the direct tensile to flexural tensile strength ratio of the matrixes used in the test was 0.2 to 0.4. Finally, the tensile stress–strain relationship for the tested FRCMs was idealised by a bi- or tri-linear curve.

Durability of coral-reef-sand concrete beams reinforced with basalt fibre-reinforced polymer bars in seawater

2021 ◽  
pp. 136943322098166
Author(s):  
Wang Xin ◽  
Shi Jianzhe ◽  
Ding Lining ◽  
Jin Yundong ◽  
Wu Zhishen
Keyword(s):  
Coral Reef ◽  
Marine Environment ◽  
Failure Modes ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Initial Stiffness ◽  
Basalt Fibre ◽  
Rc Structures ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer

A combination of coral reef sand (CRS) concrete and fibre-reinforced polymer (FRP) bars provides an effective solution to the durability deficiency in conventional RC structures. This study experimentally investigates the durability of CRS concrete beams reinforced with basalt FRP (BFRP) bars in a simulated marine environment. Flexural tests are conducted on a total of fourteen CRS concrete beams aged in a cyclic wet-dry saline solution at temperatures of 25, 40 and 55°C. The variables comprise the types of reinforcement (steel and BFRP), the aging duration and the temperature. The failure modes, capacities, deflections and crack development of the beams are analysed and discussed. The results indicate that the ultimate load of the beams exhibits no degradation after aging, whereas the failure mode of the BFRP-CRS concrete beams transition from flexure to shear, which is caused by the degradation in the mechanical properties of the stirrups. The aged BFRP-CRS concrete beams show a substantial increase of over 70% in their initial stiffness compared with the control beams (beams without aging) and a substantial decrease in their crack width after aging due to the prolonged maturation of the concrete. Furthermore, a formula for calculating the shear capacity in the existing code is modified by a partial factor equal to 2, which can predict the capacity of a CRS concrete beam reinforced with BFRP bars in a marine environment.

Sign in / Sign up

Export Citation Format

Share Document