scholarly journals Evaluation of the drinking water treatment system (STAP) San Fernando –Los Patios urbanization, Colombia. Efficiency and quality

2020 ◽  
Vol 19 (4) ◽  
pp. 149-156
Author(s):  
Yusbely Cecilia Castrillón-Jaimes ◽  
Carlos Humberto Acevedo-Peñaloza ◽  
Jhan Piero Rojas-Suárez

The quality of water for human consumption in the municipality of Los Patios in Colombia, depends 60% of the treatment systems for drinking water (STAP) independent, these are adapted according to the population that conforms in 2014 and own resources. Urbanization San Fernando carries out the treatment in an efficient way guaranteeing the quality of water for human consumption, therefore, the field study is based on a quantitative approach and a method that describes the results of the analysis of the samples taken at the entrance and exit of the STAP, to evaluate the efficiency and quality of the system the sample is characterized from the analysis of the physical-chemical and microbiological parameters at the entrance and exit of the system in the Water Laboratory of the Universidad Francisco de Paula de Santander. The physical and microbiological results identify the efficiency of the system and the operator, indicating the quality of the water by the values in the parameters measured according to Decree 1575 of 2007 and 1525 of 2007 by the Ministry of Social Protection in Colombia. The chemical analyses detected a high percentage of calcium hardness in the sample at the system outlet, which is reportedto the directors of the urbanization. In accordance with this, the relevant controls and monitoring are carried out in the process for the purification and consumption of water, without neglecting the habits of water storage by the community in each home.

2019 ◽  
Vol 4 (1) ◽  
pp. 65
Author(s):  
Sandna Larissa Freitas Santos ◽  
Leandro Lima de Vasconcelos ◽  
Rogério Nunes dos Santos

Os intensos períodos de estiagem e pela concentração que a água adquire quando os níveis dos reservatórios estão baixos torna-se evidente a ausência da qualidade da água consumida pela população. O estudo teve como objetivo avaliar os parâmetros físico-químicos e microbiológicos da água para consumo no município de Itapiúna-CE. Estudo do tipo experimental, prospectivo, transversal e com abordagem do tipo qualitativo e quantitativo. Foram analisadas 4 amostras de 500 mL cada, uma do Açude Castro e de três locais escolhidos nas residências de pontos estratégicos de distribuição pela concepcionária, da água usada para consumo no município de Itapiúna-CE no mês de outubro de 2016. Para seleção das amostras foram adotados os critérios de inclusão: água do açude castro (Amostra A), e três amostras de residências, consideradas a água retirada diretamente do registro da Cagece, escolhidas aleatoriamente dos bairros do município. As amostras apresentaram cloretos alterados quando comparadas às quantidades estabelecidas pela Portaria 2914/2011 do Ministério da Saúde (MS). A respeito aos parâmetros como Sólidos Totais, Condutividade, Cloreto e Dureza, os valores também encontrou-se valores superiores. A amostra A (Açude Castro) obteve pH de 8.81 e apresentou alcalinidade devido a carbonatos (80 mgCO3/L) e a bicarbonatos (150mg CaCO3/L). Verificou-se que 50% das amostras apresentaram presença de coliformes totais e coliformes fecais, evidenciando contaminação da maioria das amostras analisadas. Contudo, de acordo com as análises realizadas, as amostras não obedecem ao padrão de potabilidade, tornando á água imprópria para o consumo humano. PHYSICAL-CHEMICAL AND MICROBIOLOGICAL QUALITY OF WATER FOR CONSUMPTION IN RESIDENCES OF A TOWN IN THE SERTÃO CENTRAL ABSTRACT Factors such as long periods of drought and the physical and chemical characteristics of water influence in the quality of water consumed by the population, leading to health problems. This study aimed at evaluating the physical-chemical and microbiological parameters of water for consumption in the town of Itapiúna-CE. Four samples of 500 mL each were analyzed, one from Açude Castro and three from chosen places in the residences of strategic sites of distribution by the water company for consumption in the town of Itapiúna-CE in October 2016. For sample selection it was adopted the inclusion criteria: water from Açude Castro (sample A), and three samples of residences, considered the water withdrawn directly from Cagece register, randomly chosen from neighborhoods of the town. The samples present altered chlorides compared to the established quantities by the Consolidation Ordinance No. 5 of September 28, 2017 of the Ministry of Health (MS). Regarding the parameters such as total solids, conductivity, chloride and hardness, were also found higher values. Sample A (Açude Castro) obtained pH of 8.81 and presented alkalinity due to carbonates (80 mgCO3 / L) and bicarbonates (150 mg CaCO3 / L). It was verified that 50% of the samples presented total coliforms and fecal coliforms, evidencing contamination of most of the samples analyzed. So, according to the analysis carried out, the samples did not obey the standard of potable water, making the water unfit for human consumption.


2015 ◽  
Vol 9 (08) ◽  
pp. 844-848 ◽  
Author(s):  
Sita Malhotra ◽  
Shailpreet K Sidhu ◽  
Pushpa Devi

Introduction: Safe water is a precondition for health and development and is a basic human right, yet it is still denied to hundreds of millions of people throughout the developing world. Water-related diseases caused by insufficient safe water supplies, coupled with poor sanitation and hygiene, cause 3.4 million deaths a year, mostly in children. Methodology: The present study was conducted on 1,317 drinking water samples from various water sources in Amritsar district in northern India. All the samples were analyzed to assess bacteriological quality of water for presumptive coliform count by the multiple tube test. Results: A total of 42.9% (565/1,317) samples from various sources were found to be unfit for human consumption. Of the total 565 unsatisfactory samples, 253 were from submersible pumps, 197 were from taps of piped supply (domestic/public), 79 were from hand pumps, and 36 were from various other sources A significantly high level of contamination was observed in samples collected from submersible pumps (47.6%) and water tanks (47.3%), as these sources of water are more exposed and liable to contamination. Conclusions: Despite continuous efforts by the government, civil society, and the international community, over a billion people still do not have access to improved water resources. Bacteriological assessment of all sources of drinking should be planned and conducted on regular basis to prevent waterborne dissemination of diseases.


Ciencia Unemi ◽  
2016 ◽  
Vol 9 (20) ◽  
pp. 109 ◽  
Author(s):  
Renato Baque Mite ◽  
Luis Simba Ochoa ◽  
Betty Gonzalez Osorio ◽  
Pedro Suatunce ◽  
Eduardo Diaz Ocampo ◽  
...  

El estudio evaluó la calidad del agua destinada al consumo humano en el cantón Quevedo, provincia de Los Ríos, Ecuador. Se evaluaron parámetros físicos, químicos y microbiológicos del agua en nueve estaciones de bombeo del EPMAPAQ, en épocas lluviosa y seca. Se compararon los resultados obtenidos con los valores de referencia establecidos en las normativas (Acuerdo ministerial Nº 097 Norma INEN 1108, TULSMA, EPA y OMS), bajo el criterio de calidad para aguas destinadas al consumo humano y uso doméstico. Se determinó el Índice de Calidad de Agua (ICA) y la correlación estadística entre los parámetros, usando la prueba de “t” de Student, con una significancia estadística de p = 0,05 entre las dos épocas. Los parámetros: nitritos, nitratos, turbidez, sólidos disueltos totales, pH, dureza total, color y hierro, se encuentran en el rango de aceptabilidad de calidad ambiental. Los valores, manganeso y oxígeno disuelto sobrepasan los límites máximos permisibles por el TULSMA, al igual que los coliformes fecales, en época lluviosa. La mayoría de los parámetros presentaron diferencias significativas (“t” al 5%) entre las dos épocas. El agua del cantón Quevedo está levemente contaminada y requiere tratamiento de potabilización previo a su consumo. ABSTRACTThe study evaluated the quality of water intended for human consumption in the canton Quevedo, province of Los Rios, Ecuador. Physical, chemical and microbiological parameters of water in nine EPMAPAQ pumping stations were evaluated, in rainy and dry seasons. The results obtained with the reference values set out in the regulations (Ministerial Agreement No. 097 Standard INEN 1108, TULSMA, EPA and WHO) under the quality criterion for water intended for human consumption and domestic use was compared. The Water Quality Index (ICA) and the statistical correlation between parameters were determined using the test "t" of Student, with a statistical significance of p = 0.05 between the two periods. Parameters: nitrites, nitrates, turbidity, total dissolved solids, pH, total hardness, color and iron are in the range of acceptability environmental quality. Values, manganese, dissolved oxygen exceed the maximum permissible limits for the TULSMA, like fecal coliform in the rainy season. Most parameters showed significant differences ("t" 5%) between the two periods. Quevedo Canton water is slightly contaminated and requires purification treatment before consumption.


2017 ◽  
Vol 2 (6) ◽  
pp. 42
Author(s):  
Abdulkadir A. Gidado ◽  
Ibrahim Halliru ◽  
Christiana Anawuese Kendeson ◽  
Yusuf Abdullahi

In a bid to ascertain the quality of water for human consumption in Kashere Metropolis, essential physico-chemical parameters were evaluated on samples of drinking water obtained from boreholes, pond and wells located at densely populated areas, labelled as: Kashere cattle market Pond, KP; Kashere cottage Hospital Borehole, HB; Kashere Market Borehole, MB; Federal University, Kashere (FUK) campus Borehole, CB; Kashere cottage Hospital Well, HW; Kashere Market Well, MW and FUK campus Well, CW. Standard procedure for the determination of chemical and physical characteristics of the water samples were used. The results of the investigated parameters in the samples were as follows: ρH 6.61‒7.96, Turbidity 0.0‒2568 FTU, Electrical Conductivity 60.5‒1151 Mhocm-1, Total Dissolved Solids (TDS) 25.9‒518.0 mgL-1, Ca 0.0033‒0.5446 ppm, Mg 0.0793‒1.2215 ppm, Cd 0.0010‒0.0030 ppm, Zn 0.0024‒0.l054 ppm, Pb 0.0002‒0.0026 ppm and Fe 0.0044‒0.5649 ppm. Except for the concentration of Fe (in CB; 0.5649 ppm), all the analyzed minor and major cations in the water samples were in very low concentration and below the permissible limits of WHO standard guidelines values for drinking water.  It is recommended that, water from the pond should be properly treated before consumption due to its high turbidity.  Also periodic assessment of the quality of drinking water from these water sources should be conducted, to ascertain that they are not contaminated by either or both organic and inorganic pollutants.


1998 ◽  
Vol 37 (2) ◽  
pp. 333-341
Author(s):  
Gerhard Bjørnsen ◽  
Rolf Gimbel ◽  
Hans-Dieter Spangenberg

To guarantee drinking water of high quality not only the drinking water treatment must be of high standards but also the quality of water resources should be the best possible. Therefore, pollution control and pollution risk management in the catchment areas of water resources are important parts of an overall water management concept. This includes the assessment of physical and chemical parameters as well as bacteriological parameters, especially hygienic parameters. A concept for an integrative consideration of drinking water treatment and quality management of water resources is presented.


2018 ◽  
Vol 5 (13) ◽  
pp. 55 ◽  
Author(s):  
Karim Musalem-Castillejos ◽  
Rafael Laino-Guanes ◽  
Ricardo Bello-Mendoza ◽  
Mario González-Espinoza ◽  
Neptalí Ramírez-Marcial

The objective was to characterize water quality for a section of the Grijalva River and its tributaries, for rainy and dry season in the border of the States of Chiapas and Tabasco. 23 physical, chemical, and microbiological parameters as well as contaminants were determined and compared with the Mexican norm NOM-127-SSA1-1994 which establishes water quality maximum permissible limits for use and human consumption and with the water quality classi cation scale proposed by the Comisión Nacional del Agua. Water quality of the Grijalva River in the studied section and tributaries, also locally named Almandros river, decreases as it descends to more populated areas of Tabasco. Water turbidity and high levels of coliforms and Escherichia are the main problems associated with the rivers of the studied area, even in water sources destined for human consumption. Other studied parameters have acceptable water quality mainly during the dry season, except for Mercury, which showed higher levels than the recommended by the norm in all sampling sites. The need to further study presence of Mercury in the Grijalva River basin is suggested. 


Author(s):  
María Socorro Espino-Valdés ◽  
Cristina Hernández-Herrera ◽  
Adán Pinales-Munguía ◽  
María de Lourdes Ballinas-Casarrubias

Arsenic and fluorine occur naturally in groundwater, especially in desert and semi-desert areas. Chronic exposure through drinking water to these substances causes adverse health effect, which are limited in water intended for human consumption. Objective: This work was carried out with the aim of improving the quality of water from wells with high contents of arsenic and fluorine, achieving compliance with the limits established in the Mexican regulations for drinking water. Methodology: A system of two-panel solar distillation was used for treatment of water from three wells characterized by high levels of arsenic and fluoride, which are intended for human consumption. Contribution: The solar distillation system used improved the quality of the groundwater through the removal of arsenic (99%), fluoride (96%) and dissolved solids (98%). The proven system is a viable alternative for water treatment in small communities that do not have access to demineralization water plants that operate with high costs, thus eliminating health risks associated to the chronic intake of these elements.


2021 ◽  
Vol 10 (11) ◽  
pp. e198101119357
Author(s):  
Thander Jacson Nunes Calente ◽  
Grazieli Nunes Calente Santos ◽  
Wesclen Vilar Nogueira

The study analyzed the physical-chemical and microbiological parameters carried out by the Autonomous Water and Sewage Service (AWSS) of the Municipality of Alvorada D’Oeste, Rondônia, Brazil. The parameters analyzed were: pH, turbidity, free residual chlorine, total coliforms (TC), thermotolerant coliforms (TTC) and heterotrophic bacteria. The values of hydrogen potential (pH) were obtained with a digital pH meter. The analyzes were carried out the 2013 to 2019. The turbidity and free residual chlorine values were obtained according to the method of the Practical Manual of Water Analysis of the National Health Foundation (FUNASA). To determine the microbiological parameters, PetrifilmTM plates (3MTM do Brasil Ltda) were used, following the manufacturer's guidelines. The analyzed values were compared with reference values described in Consolidation Ordinance nº. 5, of September 28, 2017, of the Ministry of Health (MS) which sets the standards for potability of water intended for human consumption. The results varied for all parameters evaluated: pH (3.11 to 8.24), turbidez (0.02 to 3,01), TC (0 to 100%), TTC (0 to 100%) and heterotrophic bacteria (85 to 100%). The values obtained for free residual chlorine were the only parameter to follow the reference values. The highest contamination for TC and heterotrophic bacteria were reported in 2019, higher the limits established in Brazilian legislation. Thus, the water was characterized as unfit for consumption and requires severe control for TC and heterotrophic bacteria.  


2019 ◽  
Author(s):  
Wenfa Ng

Quality of produced water is usually the criterion for selecting between different desalination technologies for turning seawater into drinking water. However, contemporary trend in drinking water treatment sees a convergence between different technologies for the same water quality. Hence, how do different desalination technologies differentiate amongst each other? Awareness of climate change impact as well as price of produced water, energy use per unit of treated water is an oft-used criterion for assessing the effectiveness and efficiency of different desalination technologies. Specifically, comparing multi-effect flash evaporation and reverse osmosis, the latter enjoys a significant energy use advantage given the lack of the need for converting water into the vapor phase as in multi-effect flash evaporation. Thus, energy used in producing drinking water is significantly higher in multi-effect flash evaporation compared to the high pressure process of reverse osmosis. From the operation perspective, reverse osmosis also benefits from its ability to scale linearly in increasing water production capacity through addition of extra membrane modules, which is not the case for multi-effect flash evaporation where a new distillation column is required for significant increase in production capacity. Collectively, with the same quality of water produced by different desalination technologies, comparison between different technologies increasingly relies on the energy use per unit of produced water. Using this criterion, reverse osmosis membrane desalination has a significant advantage relative to multi-effect flash evaporation in energy cost, which translates to a lower price of produced water.


2017 ◽  
Vol 13 (12) ◽  
pp. 231
Author(s):  
Mohamed Achmit ◽  
Ghita Sbai ◽  
Abdelouahad Aouniti ◽  
Mohammed Loukili

In Morocco, the quality of water gathered in dams is deteriorating considerably due to different sources of pollution. One of the consequences of this situation is the presence of nutrients , particularly phosphorus and nitrogen, in the water. This, however, indicates an advanced state of eutrophisation of waters. This phenomenon causes an imbalance in the ecosystem with an anarchic development of seaweeds and an intense consumption of oxygen at the bottom of lakes. The present study aims to present the results of the optimization of the choice of the pumping area of the waters of the BAB LOUTA dam in TAZA region, Morocco. This dam is the dam that provides the city of TAZA with drinking water. The results of physico-chemical analyses (dissolved Oxygen, Turbidity, Manganese, pH, and the temperature) were taken according to a vertical deep profile for a duration that spreads from March 2016 to March 2017.


Sign in / Sign up

Export Citation Format

Share Document