scholarly journals A Numerical Method for Computing Recovery of Oil By Hot Water Injection in a Radial System

1965 ◽  
Vol 5 (02) ◽  
pp. 131-140 ◽  
Author(s):  
K.P. Fournier
Keyword(s):  
Thermal Expansion ◽  
Oil Recovery ◽  
Viscosity Ratio ◽  
Water Injection ◽  
Injection Rate ◽  
Heat Losses ◽  
Hot Water ◽  
Radial System ◽  
System Equation ◽  
Finite Difference Equations

Abstract This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of viscosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090–1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers.1–6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment.1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7,8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverett9 equation for a radial system:*Equation 1 This can be written in the formEquation 2 This is sometimes referred to as the Lagrangian form of the displacement equation.

The Research and Evaluation of Finely Layered Water Injection Standard in Low-Permeability Reservoirs - A Case from Block A in one Low-Permeability Reservoir

2014 ◽  
Vol 1073-1076 ◽  
pp. 2310-2315 ◽  
Author(s):  
Ming Xian Wang ◽  
Wan Jing Luo ◽  
Jie Ding
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Low Permeability ◽  
Reservoir Permeability ◽  
Engineering Parameters ◽  
The Common ◽  
Common Problems ◽  
Low Permeability Reservoirs

Due to the common problems of waterflood in low-permeability reservoirs, the reasearch of finely layered water injection is carried out. This paper established the finely layered water injection standard in low-permeability reservoirs and analysed the sensitivity of engineering parameters as well as evaluated the effect of the finely layered water injection standard in Block A with the semi-quantitative to quantitative method. The results show that: according to the finely layered water injection standard, it can be divided into three types: layered water injection between the layers, layered water injection in inner layer, layered water injection between fracture segment and no-fracture segment. Under the guidance of the standard, it sloved the problem of uneven absorption profile in Block A in some degree and could improve the oil recovery by 3.5%. The sensitivity analysis shows that good performance of finely layered water injection in Block A requires the reservoir permeability ratio should be less than 10, the perforation thickness should not exceed 10 m, the amount of layered injection layers should be less than 3, the surface injection pressure should be below 14 MPa and the injection rate shuold be controlled at about 35 m3/d.

Software Tool for the Study, Analysis and Evaluation of Enhanced Oil Recovery Processes

2014 ◽  
Author(s):  
C. L. Delgadillo-Aya ◽  
M.L.. L. Trujillo-Portillo ◽  
J.M.. M. Palma-Bustamante ◽  
E.. Niz-Velasquez ◽  
C. L. Rodríguez ◽  
...  
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Water Injection ◽  
Software Tool ◽  
Steam Injection ◽  
Hot Water ◽  
Assessment Process ◽  
Analytical Models ◽  
Financial Assessment ◽  
Recovery Processes

Abstract Software tools are becoming an important ally in making decisions on the development or implementation of an enhanced oil recovery processes from the technical, financial or risk point of view. This work, can be manually developed in some cases, but becomes more efficient and precise with the help of these tools. In Ecopetrol was developed a tool to make technical and economic evaluation of enhanced oil recovery processes such as air injection, both cyclic and continuous steam injection, and steam assisted gravity drainage (SAGD) and hot water injection. This evaluation is performed using different types of analysis as binary screening, analogies, benchmarking, and prediction using analytical models and financial and risk analysis. All these evaluations are supported by a comprehensive review that has allowed initially find favorable conditions for different recovery methods evaluated, and get a probability of success based on this review. Subsequently, according to the method can be used different prediction methods, given an idea of the process behavior for a given period. Based on the prediction results, it is possible to feed the software to generate a financial assessment process, in line with cash flow previously developed that incorporates all the elements to be considered during the implementation of a project. This allows for greater support to the choice or not the application of a method. Finally the tool to evaluate the levels of risks that outlines the development of the project based on the existing internal methodology in the company, identifying the main and level of criticality and define actions for prevention, mitigation and risk elimination.

Optimizing Recovery for Waterflooding Under Dynamic Induced Fracturing Conditions

2009 ◽  
Vol 12 (05) ◽  
pp. 671-682 ◽  
Author(s):  
Paul J. van den Hoek ◽  
Rashid A. Al-Masfry ◽  
Dirk Zwarts ◽  
Jan-Dirk Jansen ◽  
Bernhard Hustedt ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Injection Rate ◽  
Reservoir Engineering ◽  
Spot Pattern ◽  
Engineering Parameters ◽  
Induced Fractures ◽  
Modeling Strategy ◽  
Reservoir Simulator ◽  
Fully Coupled

Summary It is well established within the industry that water injection mostly takes place under induced fracturing conditions. Particularly in low-mobility reservoirs, large fractures may be induced during the field life. This paper presents a new modeling strategy that combines fluid flow and fracture growth (fully coupled) within the framework of an existing "standard" reservoir simulator. We demonstrate the coupled simulator by applications to repeated five-spot pattern flood models, addressing various aspects that often play an important role in waterfloods: shortcut of injector and producer, fracture containment to the reservoir layer, and areal and vertical reservoir sweep. We also demonstrate how induced fracture dimensions (length, height) can be very sensitive to typical reservoir engineering parameters, such as fluid mobility, mobility ratio, 3D saturation distribution (in particular, shockfront position), 3D temperature distribution, positions of wells (producers, injectors), and geological details (e.g., layering and faulting). In particular, it is shown that lower overall (time-dependent) reservoir transmissibility will result in larger induced fractures. Finally, it is demonstrated how induced fractures can be taken into account to determine an optimum life-cycle injection rate strategy. The results presented in this paper are expected to also apply to (part of) enhanced-oil-recovery operations (e.g., polymer flooding).

scholarly journals Experimental Investigation on Oil Enhancement Mechanism of Hot Water Injection in tight reservoirs

Open Physics ◽  
2016 ◽  
Vol 14 (1) ◽  
pp. 703-713 ◽  
Author(s):  
Hao Yongmao ◽  
Lu Mingjing ◽  
Dong Chengshun ◽  
Jia Jianpeng ◽  
Su Yuliang ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Saturation ◽  
Water Injection ◽  
Hot Water ◽  
Water Flooding ◽  
Water Displacement ◽  
Pore Characteristics ◽  
Irreducible Water Saturation ◽  
Tight Reservoirs ◽  
Oil Water

AbstractAimed at enhancing the oil recovery of tight reservoirs, the mechanism of hot water flooding was studied in this paper. Experiments were conducted to investigate the influence of hot water injection on oil properties, and the interaction between rock and fluid, petrophysical property of the reservoirs. Results show that with the injected water temperature increasing, the oil/water viscosity ratio falls slightly in a tight reservoir which has little effect on oil recovery. Further it shows that the volume factor of oil increases significantly which can increase the formation energy and thus raise the formation pressure. At the same time, oil/water interfacial tension decreases slightly which has a positive effect on production though the reduction is not obvious. Meanwhile, the irreducible water saturation and the residual oil saturation are both reduced, the common percolation area of two phases is widened and the general shape of the curve improves. The threshold pressure gradient that crude oil starts to flow also decreases. It relates the power function to the temperature, which means it will be easier for oil production and water injection. Further the pore characteristics of reservoir rocks improves which leads to better water displacement. Based on the experimental results and influence of temperature on different aspects of hot water injection, the flow velocity expression of two-phase of oil and water after hot water injection in tight reservoirs is obtained.

scholarly journals Experimental Study on Enhanced Oil Recovery by Nitrogen-Water Alternative Injection in Reservoir with Natural Fractures

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiang Li ◽  
Yuan Cheng ◽  
Wulong Tao ◽  
Shalake Sarulicaoketi ◽  
Xuhui Ji ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Water Flooding ◽  
Orthogonal Experimental Design ◽  
Fractured Reservoir ◽  
Natural Fractures ◽  
Nitrogen Injection

The production of a low permeability reservoir decreases rapidly by depletion development, and it needs to supplement formation energy to obtain stable production. Common energy supplement methods include water injection and gas injection. Nitrogen injection is an economic and effective development method for specific reservoir types. In order to study the feasibility and reasonable injection parameters of nitrogen injection development of fractured reservoir, this paper uses long cores to carry out displacement experiment. Firstly, the effects of water injection and nitrogen injection development of a fractured reservoir are compared through experiments to demonstrate the feasibility of nitrogen injection development of the fractured reservoir. Secondly, the effects of gas-water alternate displacement after water drive and gas-water alternate displacement after gas drive are compared through experiments to study the situation of water injection or gas injection development. Finally, the reasonable parameters of nitrogen gas-water alternate injection are optimized by orthogonal experimental design. Results show that nitrogen injection can effectively enhance oil production of the reservoir with natural fractures in early periods, but gas channeling easily occurs in continuous nitrogen flooding. After water flooding, gas-water alternate flooding can effectively reduce the injection pressure and improve the reservoir recovery, but the time of gas-water alternate injection cannot be too late. It is revealed that the factors influencing the nitrogen-water alternative effect are sorted from large to small as follows: cycle injected volume, nitrogen and water slug ratio, and injection rate. The optimal cycle injected volume is around 1 PV, the nitrogen and water slug ratio is between 1 and 2, and the injection rate is between 0.1 and 0.2 mL/min.

Low Salinity Hot Water Injection With Addition of Nanoparticles for Enhancing Heavy Oil Recovery

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Yanan Ding ◽  
Sixu Zheng ◽  
Xiaoyan Meng ◽  
Daoyong Yang
Keyword(s):  
Thermal Energy ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Water Injection ◽  
Operating Conditions ◽  
Hot Water ◽  
Wettability Alteration ◽  
Heavy Oil Recovery ◽  
Oil Saturation ◽  
Low Salinity

In this study, a novel technique of low salinity hot water (LSHW) injection with addition of nanoparticles has been developed to examine the synergistic effects of thermal energy, low salinity water (LSW) flooding, and nanoparticles for enhancing heavy oil recovery, while optimizing the operating parameters for such a hybrid enhanced oil recovery (EOR) method. Experimentally, one-dimensional displacement experiments under different temperatures (17 °C, 45 °C, and 70 °C) and pressures (about 2000–4700 kPa) have been performed, while two types of nanoparticles (i.e., SiO2 and Al2O3) are, respectively, examined as the additive in the LSW. The performance of LSW injection with and without nanoparticles at various temperatures is evaluated, allowing optimization of the timing to initiate LSW injection. The corresponding initial oil saturation, production rate, water cut, ultimate oil recovery, and residual oil saturation profile after each flooding process are continuously monitored and measured under various operating conditions. Compared to conventional water injection, the LSW injection is found to effectively improve heavy oil recovery by 2.4–7.2% as an EOR technique in the presence of nanoparticles. Also, the addition of nanoparticles into the LSHW can promote synergistic effect of thermal energy, wettability alteration, and reduction of interfacial tension (IFT), which improves displacement efficiency and thus enhances oil recovery. It has been experimentally demonstrated that such LSHW injection with the addition of nanoparticles can be optimized to greatly improve oil recovery up to 40.2% in heavy oil reservoirs with low energy consumption. Theoretically, numerical simulation for the different flooding scenarios has been performed to capture the underlying recovery mechanisms by history matching the experimental measurements. It is observed from the tuned relative permeability curves that both LSW and the addition of nanoparticles in LSW are capable of altering the sand surface to more water wet, which confirms wettability alteration as an important EOR mechanism for the application of LSW and nanoparticles in heavy oil recovery in addition to IFT reduction.

scholarly journals Impact of injection rate on transient oil recovery under mixed-wet conditions: a microfluidic study

2019 ◽  
Vol 89 ◽  
pp. 04002 ◽  
Author(s):  
Magali Christensen ◽  
Xanat Zacarias-Hernandez ◽  
Yukie Tanino
Keyword(s):  
Oil Recovery ◽  
Strong Dependence ◽  
Water Injection ◽  
Microfluidic Channel ◽  
Early Time ◽  
Packed Bed ◽  
Injection Rate ◽  
End Effects ◽  
Oil Saturation ◽  
End Point

Lab-on-a-chip methods were used to visualize the pore-scale distribution of oil within a mixed-wet, quasi-monolayer of marble grains packed in a microfluidic channel as the oil was displaced by water. Water injection rates corresponding to microscopic capillary numbers between Ca = 5 × 10-8 and 2 × 10-4 (Darcy velocities between 0.3 and 1100 ft/d) were considered. As expected, early-time water invasion transitions from stable displacement to capillary fingering with decreasing Ca, with capillary fingering observed at Ca ≤ 10-5. End-point oil saturation decreases with Ca over the entire range of Ca considered, consistent with the canonical capillary desaturation curve. In contrast, Sor derived from approximate numerical simulations using reasonable Pc(Sw) do not display a strong dependence on Ca. These results suggest that the Ca dependence of end-point oil saturation is largely due to capillary end effects which, under conditions considered presently, affect the entire length of the packed bed.

The Perspective of Novel Chemical Tracer Technology in Reservoir Surveillance and Hydrodynamic Modelling for More Efficient Hydrocarbon Recovery

2021 ◽  
Author(s):  
Nadir Husein ◽  
Evgeny Aleksandrovich Malyavko ◽  
Ruslan Rashidovich Gazizov ◽  
Anton Vitalyevich Buyanov ◽  
Aleksey Aleksandrovich Romanov ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Continuous Production ◽  
Economic Effect ◽  
Water Injection ◽  
Injection Rate ◽  
Reservoir Pressure ◽  
Entire Area ◽  
Field Development ◽  
Oil Companies ◽  
Maintenance System

Abstract Today, efficient field development cannot be managed without proper surveillance providing oil companies with important geological and engineering information for prompt decision-making. Once continuous production is achieved, it is necessary to maintain a consistently high level of oil recovery. As a rule, a reservoir pressure maintenance system is extensively implemented for this purpose over the entire area because of decreasing reservoir pressure. At the same time, it is important to adjust the water injection to timely prevent water cut increasing in production wells, while maintaining efficient reservoir pressure compensation across the field. That is why it is necessary to have a relevant inter-well hydrodynamic model as well as to quantify the water injection rate. There are many ways to analyse the efficiency of the reservoir pressure maintenance system, but not all of them yield a positive, and most importantly, a reliable result. It is crucial that extensive zonal production surveillance efforts generate a significant economic effect and the information obtained helps boost oil production. Thus, the main objective of this paper is to identify a method and conduct an effective study to establish the degree of reservoir connectivity and quantify the inter-well parameters of a low permeability tested field.

scholarly journals Simulation Study of Allied In-Situ Injection and Production for Enhancing Shale Oil Recovery and CO2 Emission Control

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3961
Author(s):  
Haiyang Yu ◽  
Songchao Qi ◽  
Zhewei Chen ◽  
Shiqing Cheng ◽  
Qichao Xie ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Co2 Emission ◽  
Gas Injection ◽  
Water Injection ◽  
Oil Production ◽  
Injection Rate ◽  
Oil Reservoirs ◽  
Shale Oil ◽  
Shale Oil Reservoirs

The global greenhouse effect makes carbon dioxide (CO2) emission reduction an important task for the world, however, CO2 can be used as injected fluid to develop shale oil reservoirs. Conventional water injection and gas injection methods cannot achieve desired development results for shale oil reservoirs. Poor injection capacity exists in water injection development, while the time of gas breakthrough is early and gas channeling is serious for gas injection development. These problems will lead to insufficient formation energy supplement, rapid energy depletion, and low ultimate recovery. Gas injection huff and puff (huff-n-puff), as another improved method, is applied to develop shale oil reservoirs. However, the shortcomings of huff-n-puff are the low sweep efficiency and poor performance for the late development of oilfields. Therefore, this paper adopts firstly the method of Allied In-Situ Injection and Production (AIIP) combined with CO2 huff-n-puff to develop shale oil reservoirs. Based on the data of Shengli Oilfield, a dual-porosity and dual-permeability model in reservoir-scale is established. Compared with traditional CO2 huff-n-puff and depletion method, the cumulative oil production of AIIP combined with CO2 huff-n-puff increases by 13,077 and 17,450 m3 respectively, indicating that this method has a good application prospect. Sensitivity analyses are further conducted, including injection volume, injection rate, soaking time, fracture half-length, and fracture spacing. The results indicate that injection volume, not injection rate, is the important factor affecting the performance. With the increment of fracture half-length and the decrement of fracture spacing, the cumulative oil production of the single well increases, but the incremental rate slows down gradually. With the increment of soaking time, cumulative oil production increases first and then decreases. These parameters have a relatively suitable value, which makes the performance better. This new method can not only enhance shale oil recovery, but also can be used for CO2 emission control.

Sign in / Sign up

Export Citation Format

Share Document