Waterflooding in Carbonate Reservoirs: Does the Salinity Matter?

2014 ◽  
Vol 17 (03) ◽  
pp. 304-313 ◽  
Author(s):  
A.M.. M. Shehata ◽  
M.B.. B. Alotaibi ◽  
H.A.. A. Nasr-El-Din
Keyword(s):  
Oil Recovery ◽  
Sudden Change ◽  
Oil Production ◽  
Deionized Water ◽  
Production Performance ◽  
Shallow Aquifer ◽  
Secondary Recovery ◽  
Tertiary Recovery ◽  
The Impact ◽  
Indiana Limestone

Summary Waterflooding has been used for decades as a secondary oil-recovery mode to support oil-reservoir pressure and to drive oil into producing wells. Recently, the tuning of the salinity of the injected water in sandstone reservoirs was used to enhance oil recovery at different injection modes. Several possible low-salinity-waterflooding mechanisms in sandstone formations were studied. Also, modified seawater was tested in chalk reservoirs as a tertiary recovery mode and consequently reduced the residual oil saturation (ROS). In carbonate formations, the effect of the ionic strength of the injected brine on oil recovery has remained questionable. In this paper, coreflood studies were conducted on Indiana limestone rock samples at 195°F. The main objective of this study was to investigate the impact of the salinity of the injected brine on the oil recovery during secondary and tertiary recovery modes. Various brines were tested including deionized water, shallow-aquifer water, seawater, and as diluted seawater. Also, ions (Na+, Ca2+, Mg2+, and SO42−) were particularly excluded from seawater to determine their individual impact on fluid/rock interactions and hence on oil recovery. Oil recovery, pressure drop across the core, and core-effluent samples were analyzed for each coreflood experiment. The oil recovery using seawater, as in the secondary recovery mode, was, on the average, 50% of original oil in place (OOIP). A sudden change in the salinity of the injected brine from seawater in the secondary recovery mode to deionized water in the tertiary mode or vice versa had a significant effect on the oil-production performance. A solution of 20% diluted seawater did not reduce the ROS in the tertiary recovery mode after the injection of seawater as a secondary recovery mode for the Indiana limestone reservoir. On the other hand, 50% diluted seawater showed a slight change in the oil production after the injection of seawater and deionized water slugs. The Ca2+, Mg2+, and SO42− ions play a key role in oil mobilization in limestone rocks. Changing the ion composition of the injected brine between the different slugs of secondary and tertiary recovery modes showed a measurable increase in the oil production.

scholarly journals Breccia interlayer effects on steam-assisted gravity drainage performance: experimental and numerical study

2021 ◽  
Author(s):  
Qichen Zhang ◽  
Xiaodong Kang ◽  
Huiqing Liu ◽  
Xiaohu Dong ◽  
Jian Wang
Keyword(s):  
Numerical Simulation ◽  
Oil Recovery ◽  
Oil Sands ◽  
Numerical Study ◽  
Middle Part ◽  
Experimental Results ◽  
Production Performance ◽  
Peak Oil ◽  
Steam Chamber ◽  
The Impact

AbstractCurrently, the reservoir heterogeneity is a serious challenge for developing oil sands with SAGD method. Nexen’s Long Lake SAGD project reported that breccia interlayer was widely distributed in lower and middle part of reservoir, impeding the steam chamber expansion and heated oil drainage. In this paper, two physical experiments were conducted to study the impact of breccia interlayer on development of steam chamber and production performance. Then, a laboratory scale numerical simulation model was established and a history match was conducted based on the 3D experimental results. Finally, the sensitivity analysis of thickness and permeability of breccia layer was performed. The influence mechanism of breccia layer on SAGD performance was analyzed by comparing the temperature profile of steam chamber and production dynamics. The experimental results indicate that the existence of breccia interlayer causes a thinner steam chamber profile and longer time to reach the peak oil rate. And, the ultimate oil recovery reduced 15.8% due to much oil stuck in breccia interlayer areas. The numerical simulation results show that a lower permeability in breccia layer area has a serious adverse impact on oil recovery if the thickness of breccia layer is larger, whereas the effect of permeability on SAGD performance is limited when the breccia layer is thinner. Besides, a thicker breccia layer can increase the time required to reach the peak oil rate, but has a little impact on the ultimate oil recovery.

Quantifying the Impact of Permeability Heterogeneity on Secondary-Recovery Performance

SPE Journal ◽  
2012 ◽  
Vol 17 (02) ◽  
pp. 455-468 ◽  
Author(s):  
B.. Rashid ◽  
A.H.. H. Muggeridge ◽  
A.. Bal ◽  
G.. Williams
Keyword(s):  
Oil Recovery ◽  
Single Phase ◽  
Viscosity Ratio ◽  
Shear Strain Rate ◽  
Breakthrough Time ◽  
Permeability Heterogeneity ◽  
Secondary Recovery ◽  
Recovery Performance ◽  
The Impact ◽  
Immiscible Displacements

Summary An improved heterogeneity/homogeneity index is introduced that uses the shear-strain rate of the single-phase-velocity field to characterize heterogeneity and rank geological realizations in terms of their impact on secondary-recovery performance. The index is compared with the Dykstra-Parsons coefficient (Dykstra and Parsons 1950) and the dynamic Lorenz coefficient (Shook and Mitchell 2009). The results show that the index's ranking ability is preserved for miscible and immiscible displacements at different viscosity/mobility ratios. Neither the Dykstra-Parsons coefficient (Dykstra and Parsons 1950) nor the dynamic Lorenz coefficient (Shook and Mitchell 2009) can consistently discriminate between different realizations in terms of breakthrough time and oil recovery at 1 pore volume injected (PVI) for tracer flow or adverse-viscosity-ratio miscible and immiscible floods.

scholarly journals Oil recovery for fractured-vuggy carbonate reservoirs by cyclic water huff and puff: performance analysis and prediction

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Daigang Wang ◽  
Jingjing Sun
Keyword(s):  
Oil Recovery ◽  
History Matching ◽  
High Efficiency ◽  
Carbonate Reservoir ◽  
Carbonate Reservoirs ◽  
Production Performance ◽  
Quantitative Prediction ◽  
Attractive Alternative ◽  
Marquardt Algorithm ◽  
The Impact

Abstract Cyclic water huff and puff (CWHP) has proven to be an attractive alternative to improve oil production performance after depletion-drive recovery in fractured-vuggy carbonate reservoirs. However, due to the impact of strong heterogeneity, multiple types of fractured-vuggy medium, poor connectivity, complex flow behaviors and oil-water relationship, CWHP is merely suitable for specific types of natural fractured-vuggy medium, usually causing a great difference in actual oil-yielding effect. It remains a great challenge for accurate evaluation of CWHP adaptability and quantitative prediction of production performance in fractured-vuggy carbonate reservoir, which severely restricts the application of CWHP. For this study, we firstly enable the newly developed fuzzy grey relational analysis to quantify the adaptability of CWHP. With production history of several targeted producers, the accuracy of the proposed method is validated. Based on the traditional percolation theory and waterflood mechanisms in various types of fractured-vuggy medium, a quantitative prediction model for cyclic water cut fwp and increased recovery factor ΔR is presented. The CWHP production performance is discussed by using the Levenberg-Marquardt algorithm for history matching. With a better understanding of the fwp ~ ΔR curve characteristics in different types of fractured-vuggy medium, proper strategies or measures for potential-tapping remaining oil are provided. This methodology can also offer a good basis for engineers and geologists to develop other similar reservoirs with high efficiency.

Development of Tight Upper Cretaceous Reservoir in Offshore Black Sea Adds Life to a Mature Asset

2021 ◽  
Author(s):  
I. Mitrea ◽  
R. Cataraiani ◽  
M. Banu ◽  
S. Shirzadi ◽  
W. Renkema ◽  
...  
Keyword(s):  
Black Sea ◽  
Upper Cretaceous ◽  
Rock Physics ◽  
Oil Production ◽  
Economic Life ◽  
Production Performance ◽  
Single Fracture ◽  
Well Performance ◽  
Acoustic Image ◽  
The Impact

Abstract This Upper Cretaceous reservoir, a tight reservoir dominated by silt, marl, argillaceous limestone and conglomerates in Black Sea Histria block, is the dominant of three oil-producing reservoirs in Histria Block. The other two, Albian and Eocene, are depleted, and not the focus of field re-development. This paper addresses the challenges and opportunities that were faced during the re-development process in this reservoir such as depletion, low productivity areas, lithology, seismic resolution, and stimulation effectiveness. Historically, production from Upper Cretaceous wells could not justify the economic life of the asset. As new fracturing technology evolved in recent years, the re-development focused on replacing old, vertical/deviated one-stage stimulations low producing wells with horizontal, multi-stage hydraulic fractured wells. The project team integrated various disciplines and approaches by re-processing old seismic to improve resolution and signal, integrating sedimentology studies using cores, XRF, XRD and thin section analysis with petrophysical evaluation and quantitative geophysical analyses, which then will provide properties for geological and geomechanical models to optimize well planning and fracture placement. Seven wells drilled since end of 2017 to mid-2021 have demonstrated the value of integration and proper planning in development of a mature field with existing depletion. Optimizing the well and fracture placement with respect to depletion in existing wells resulted in accessing areas with original reservoir pressure, not effectively drained by old wells. Integrating the well production performance with tracer results from each fractured stage, and NMR/Acoustic images from logs enhanced the understanding of the impact of lithofacies on stimulation. This has allowed better assessment and prediction of well performance, ultimately improving well placement and stimulation design. The example from this paper highlights the value of the integrating seismic reprocessing, attribute analysis, production technology, sedimentology, cuttings analysis and quantitative rock physics in characterizing the heterogeneity of the reservoir, which ultimately contributed to "sweet spot" targeting in a depleted reservoir with existing producers and deeper understanding of the development potential in Upper Cretaceous. The 2017-2021 wells contribute to more than 30 percent of the total oil production in the asset and reverse the decline in oil production. In addition, these wells have two to four times higher initial rates because of larger effective drainage area than a single fracture well. Three areas of novelty are highlighted in this paper. The application of acoustic image/NMR logging to identify lithofacies and optimize fracturing strategy in horizontal laterals. The tracers analysis of hydraulic fracture performance and integration with seismic and petrophysical analysis to categorize the productivity with rock types. The optimization of fracture placement considering the changes of fluid and proppant volumes without compromising fracture geometries and avoiding negative fracture driven interactions by customized pumping approach.

Application of Multilateral Wells for Production and Enhanced Oil Recovery: Case Studies from Canada

2021 ◽  
pp. 1-23
Author(s):  
Eric Delamaide
Keyword(s):  
Oil Recovery ◽  
Horizontal Wells ◽  
Production Performance ◽  
Water Production ◽  
Public Data ◽  
Heavy Oil Reservoirs ◽  
Complex Architectures ◽  
Cumulative Production ◽  
Tertiary Recovery ◽  
And Performance

Summary The use of multilateral wells started in the mid-1990s in particular in Canada, and they have since been used in many countries. However, few papers on multilateral wells focus on their production performance. Thus, what can be expected from such wells in terms of production is not clear, and this paper will attempt to address that gap. Taking advantage of public data, the production performance of multilateral wells in various Western Canadian fields has been studied. In the cases reviewed in this paper, these wells always target a single formation; they have been used in a variety of fields and reservoirs, mostly for primary production but also for polymer flooding in some cases. Multiple examples will be provided, mostly in heavy oil reservoirs, and production performance will be compared with nearby horizontal wells whenever possible. From the more classical dual and trilateral, to more complex architectures with seven or eight laterals, and the more exotic with laterals drilled from laterals, the paper will present the architecture and performance of these complex wells and of some fields that have been developed almost exclusively with multilateral wells. Interestingly, multilateral wells have not been used much for secondary or tertiary recovery, probably because of the difficulty of controlling water production after breakthrough. However, field results suggest that this may not be such a difficult proposition. One of the most remarkable wells producing a 1,250-cp oil under polymer flood has achieved a cumulative production of more than 3 million bbl, which puts it among the top producers in Canada. Although multilateral wells have been in use for more than 25 years, very few papers have been devoted to the description of their production performance. This paper will bring some clarity to these aspects. It will also attempt to address when multilateral wells can be used and to compare their performance to that of horizontal wells in the same fields. It is hoped that this paper will encourage operators to reconsider the use of multilateral wells in their fields.

scholarly journals Experimental study of in-situ W/O emulsification during the injection of MgSO4 and Na2CO3 solutions in a glass micromodel

2020 ◽  
Vol 75 ◽  
pp. 87
Author(s):  
Sepideh Palizdan ◽  
Hossein Doryani ◽  
Masoud Riazi ◽  
Mohammad Reza Malayeri
Keyword(s):  
Experimental Study ◽  
Flow Rate ◽  
Oil Recovery ◽  
Deionized Water ◽  
Water Flooding ◽  
Flow Rates ◽  
Glass Micromodel ◽  
The Impact ◽  
Emulsification Process

In-situ emulsification of injected brines of various types is gaining increased attention for the purpose of enhanced oil recovery. The present experimental study aims at evaluating the impact of injecting various solutions of Na2CO3 and MgSO4 at different flow rates resembling those in the reservoir and near wellbore using a glass micromodel with different permeability regions. Emulsification process was visualized through the injection of deionized water and different brines at different flow rates. The experimental results showed that the extent of emulsions produced in the vicinity of the micromodel exit was profoundly higher than those at the entrance of the micromodel. The injection of Na2CO3 brine after deionized water caused the impact of emulsification process more efficiently for attaining higher oil recovery than that for the MgSO4 brine. For instance, the injection of MgSO4 solution after water flooding increased oil recovery only up to 1%, while the equivalent figure for Na2CO3 was 28%. It was also found that lower flow rate of injection would cause the displacement front to be broadened since the injected fluid had more time to interact with the oil phase. Finally, lower injection flow rate reduced the viscous force of the displacing fluid which led to lesser occurrence of viscous fingering phenomenon.

scholarly journals An Experimental Investigation the Optimum of Salinity and Ph of Sea-Water to Improve Oil Recovery from Sandstone Reservoir as A Secondary Recovery Process

2020 ◽  
Vol 1 (2) ◽  
pp. 83
Author(s):  
Madi Abdullah Naser ◽  
Mohammed A Samba ◽  
Yiqiang Li
Keyword(s):  
Oil Recovery ◽  
Sea Water ◽  
Recovery Process ◽  
Water Flooding ◽  
Core Flooding ◽  
Low Salinity ◽  
Seawater Salinity ◽  
Secondary Recovery ◽  
Two Parameters ◽  
The Impact

Laboratory tests and field applications shows that the salinity of water flooding could lead to significant reduction of residual oil saturation. There has been a growing interest with an increasing number of low-salinity water flooding studies. However, there are few quantitative studies on seawater composition change and it impact on increasing or improving oil recovery.  This study was conducted to investigate only two parameters of the seawater (Salinity and pH) to check their impact on oil recovery, and what is the optimum amount of salinity and ph that we can use to get the maximum oil recovery.  Several core flooding experiments were conducted using sandstone by inject seawater (high, low salinity and different pH). The results of this study has been shown that the oil recovery increases as the injected water salinity down to 6500 ppm and when the pH is around 7. This increase has been found to be supported by an increase in the permeability. We also noticed that the impact of ph on oil recovery is low when the pH is less than 7.

scholarly journals Effects of Diffusion, Adsorption, and Hysteresis on Huff-n-Puff Performance in Ultratight Reservoirs with Different Fluid Types and Injection Gases

Energies ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 7379
Author(s):  
Khaled Enab ◽  
Hamid Emami-Meybodi
Keyword(s):  
Oil Recovery ◽  
Large Scale ◽  
Volatile Oil ◽  
Production Performance ◽  
Compositional Model ◽  
Reservoir Fluid ◽  
Wide Range ◽  
Black Oil ◽  
Shale Reservoirs ◽  
The Impact

Cyclic solvent injection, known as solvent huff-n-puff, is one of the promising techniques for enhancing oil recovery from shale reservoirs. This study investigates the huff-n-puff performance in ultratight shale reservoirs by conducting large-scale numerical simulations for a wide range of reservoir fluid types (retrograde condensate, volatile oil, and black oil) and different injection gases (CO2, C2H6, and C3H8). A dual-porosity compositional model is utilized to comprehensively evaluate the impact of multicomponent diffusion, adsorption, and hysteresis on the production performance of each reservoir fluid and the retention capacity of the injection gases. The results show that the huff-n-puff process improves oil recovery by 4–6% when injected with 10% PV of gas. Huff-n-puff efficiency increases with decreasing gas-oil ratio (GOR). C2H6 provides the highest recovery for the black oil and volatile oil systems, and CO2 provides the highest recovery for retrograde condensate fluid type. Diffusion and adsorption are essential mechanisms to be considered when modeling gas injection in shale reservoirs. However, the relative permeability hysteresis effect is not significant. Diffusion impact increases with GOR, while adsorption impact decreases with increasing GOR. Oil density reduction caused by diffusion is observed more during the soaking period considering that the diffusion of the injected gas caused a low prediction error, while adsorption for the injected gas showed a noticeable error.

scholarly journals Half a century of continuous oil production by in-situ combustion in Romania – case study Suplacu de Barcau field

2021 ◽  
Vol 343 ◽  
pp. 09009
Author(s):  
Gheorghe Branoiu ◽  
Florinel Dinu ◽  
Maria Stoicescu ◽  
Iuliana Ghetiu ◽  
Doru Stoianovici
Keyword(s):  
Oil Recovery ◽  
Heavy Oil ◽  
Oil Production ◽  
Oil Field ◽  
Oil Reservoir ◽  
In Situ Combustion ◽  
Cyclic Steam Stimulation ◽  
The Impact ◽  
Steam Stimulation

Thermal oil recovery is a special technique belonging to Enhanced Oil Recovery (EOR) methods and includes steam flooding, cyclic steam stimulation, and in-situ combustion (fire flooding) applied especially in the heavy oil reservoirs. Starting 1970 in-situ combustion (ISC) process has been successfully applied continuously in the Suplacu de Barcau oil field, currently this one representing the most important reservoir operated by ISC in the world. Suplacu de Barcau field is a shallow clastic Pliocene, heavy oil reservoir, located in the North-Western Romania and geologically belonging to Eastern Pannonian Basin. The ISC process are operated using a linear combustion front propagated downstructure. The maximum oil production was recorded in 1985 when the total air injection rate has reached maximum values. Cyclic steam stimulation has been continuously applied as support for the ISC process and it had a significant contribution in the oil production rates. Nowadays the oil recovery factor it’s over 55 percent but significant potential has left. In the paper are presented the important moments in the life-time production of the oil field, such as production history, monitoring of the combustion process, technical challenges and their solving solutions, and scientific achievements revealed by many studies performed on the impact of the ISC process in the oil reservoir.

scholarly journals Comprehensive investigation of low salinity waterflooding in carbonate reservoirs

2021 ◽  
Author(s):  
M. Fouad Snosy ◽  
Mahmoud Abu El Ela ◽  
Ahmed El-Banbi ◽  
Helmy Sayyouh
Keyword(s):  
Oil Recovery ◽  
Carbonate Reservoirs ◽  
Rock Properties ◽  
Recovery Stage ◽  
Low Salinity ◽  
Water Composition ◽  
Secondary Recovery ◽  
Low Salinity Waterflooding ◽  
Tertiary Recovery ◽  
Incremental Oil Recovery

AbstractWaterflooding has been practiced as a secondary recovery mechanism for many years with no regard to the composition of the injected brine. However, in the last decade, there has been an interest to understand the impact of the injected water composition and the low salinity waterflooding (LSWF) in oil recovery. LSWF has been investigated through various laboratory tests as a promising method for improving oil recovery in carbonate reservoirs. These experiments showed diverse mechanisms and results. In this study, a comprehensive review and analysis for results of more than 300 carbonate core flood experiments from published work were performed to investigate the effects of several parameters (injected water, oil, and rock properties along with the temperature) on oil recovery from carbonate rock. The analysis of the results showed that the water composition is the key parameter for successful waterflooding (WF) projects in the carbonate rocks. However, the salinity value of the injected water seems to have a negligible effect on oil recovery in both secondary and tertiary recovery stages. The study indicated that waterflooding with optimum water composition can improve oil recovery up to 30% of the original oil in place. In addition, the investigation showed that changing water salinity from LSWF to high salinity waterflooding can lead to an incremental oil recovery of up to 18% in the tertiary recovery stage. It was evident that applying the optimum composition in the secondary recovery stage is more effective than applying it in the tertiary recovery stage. Furthermore, the key parameters of the injected water and rock properties in secondary and tertiary recovery stages were studied using Fractional Factorial Design. The results revealed that the concentrations of Mg2+, Na+, K+, and Cl− in the injected water are the greatest influence parameters in the secondary recovery stage. However, the most dominant parameters in the tertiary recovery stage are the rock minerals and the concentration of K+, HCO3−, and SO42− in the injected water. In addition, it appears that the anhydrite percentage in the carbonate reservoirs may be an effective parameter in the tertiary WF. Also, there are no clear relations between the incremental oil recovery and the oil properties (total acid number or total base number) in both secondary and tertiary recovery stages. In addition, the results of the analysis showed an incremental oil recovery in all ranges of the studied flooding temperatures. The findings of this study can help to establish guidelines for screening and designing optimum salinity and composition for WF projects in carbonate reservoirs.

Sign in / Sign up

Export Citation Format

Share Document