Application of Solid Paraffin Inhibitor in Fracturing of Kuqa Ultra Deep High Pressure and High Wax Content Tight Condensate Gas Reservoir

2021 ◽  
Author(s):  
Jueyong Feng ◽  
Hongtao Liu ◽  
Kun Huang ◽  
Ju Liu ◽  
Maotang Yao ◽  
...  
Keyword(s):  
High Pressure ◽  
Freezing Point ◽  
Freezing Temperature ◽  
Control Agent ◽  
Gas Production ◽  
Optimal Dosage ◽  
Control Effect ◽  
Gas Reservoir ◽  
Solid Paraffin ◽  
Wax Content

Abstract The buried depth of gas reservoir B is more than 6700m, the thickness of reservoir is about 180m, the porosity of reservoir matrix is mainly 5.0% - 7.0%, with an average of 6.3%, and the permeability of reservoir matrix is mainly 0.01-0.1mD, The average production capacity of the three wells is 0.08mD, the formation pressure is 116-126MPa, the formation temperature is 124-131°C, the wax content of the condensate oil is high, and the average wax content is 16.9%. In the early stage, the natural productivity of the three wells was low, and the daily gas production was 120000-180000 cubic meters after stimulation. During the production process, the wellhead temperature was 20°C-25°C, the wax freezing temperature was 35°C, and the wellbore wax plugging was serious, The wellbore was blocked, the gas well was forced to shut down, and the reserves of 100 billion cubic meters were unable to be used, so it was necessary to explore new wax control technology. Through investigation, a new type of solid particle paraffin inhibitor is introduced, which can enter the artificial fracture with proppant during fracturing. When the condensate gas passes through the fracture, it washes the solid paraffin inhibitor which enters with proppant, and becomes the condensate gas containing paraffin control components.Therefore,it is not easy to form wax after entering the wellbore, which makes the problem of wellbore paraffin formation change from "passive control" to "active control". Referring to the relevant experimental standards, the conductivity, crushing test, solid paraffin inhibitor and fracturing fluid compatibility test were carried out. The existing test standards of wax freezing point are all for waxy oil under normal pressure, but not for condensate gas. A set of innovative experimental method is designed to successfully test the wax freezing point of condensate gas containing wax control components, and obtain the wax control effect under different ratios of wax control agent and proppant, so as to optimize the amount of wax control agent used in the experiment. The results show that the solid paraffin inhibitor has good dispersibility and suspension, and has little influence on the conductivity of sand filled fractures. The paraffin control effect on condensate oil and gas in this block is good. The wax freezing point can be reduced by about 12°C-18°C, and the optimal dosage is proppant 1%-2%. Field test was carried out in B gas reservoir. After fracturing, 5mm nozzle was used for production, tubing pressure was 83.6MPa, wellhead temperature was 28.8°C, daily oil production was 10.72 cubic meters, daily gas production was 217000 cubic meters, wellhead temperature was lower than wax freezing temperature in this area. At present, it has been in production for 6 months, and there is no wax deposit in wellbore. The successful test of solid paraffin inhibitor in the fracturing of Kuqa ultra deep high pressure and high wax content tight condensate gas reservoir provides a powerful technical reference for the wellbore flow guarantee of condensate gas reservoir.

scholarly journals An Experimental Study on Percolation Characteristics of a Single-Phase Gas in a Low-Permeability Volcanic Reservoir Under High Pressure

2015 ◽  
Vol 8 (1) ◽  
pp. 186-192
Author(s):  
Tang Xiaoyan
Keyword(s):  
High Pressure ◽  
Pore Pressure ◽  
Gas Flow ◽  
Single Phase ◽  
Stress Sensitivity ◽  
Gas Production ◽  
Low Permeability ◽  
Gas Reservoir ◽  
The Core ◽  
Slippage Effect

In this paper, we find that with the decrease in the average pore pressure in the process of gas production, both the slippage effect and the stress sensitivity effect will gradually increase; the increase in the slippage effect is significant, while the increase in the stress sensitivity effect is not. In this paper, the Kalamay volcanic gas reservoir of the Junggar Basin in China was selected as the object of our research. The gas reservoir has typical fractured volcanic reservoirs, and the long-term percolation feature remains unclear. To study the percolation characteristics of singlephase gas under high pressure, the experimental method was designed to simulate these characteristics in the process of gas production by measuring the gas flow in the core and the input and the output pressure at both ends. We carried out simulation experiments of single-phase gas flow percolation characteristics under high pressure using 11 pieces of volcanic rock samples in three wells of the study area. The results show that as the core pore pressure increased, the permeability of low-permeability cores of the volcanic rock decreased significantly at room temperature. However, this decrease became more gradual, which means that the higher the core pore pressure is, the smaller the permeability variation caused by gas slippage is; when the pore pressure is above 10 MPa, the permeability is nearly constant, slippage effect significantly reduces in the process of gas percolation, so it can be completely ignored under these formation conditions. As the pore pressure decreases, the slippage effect and stress sensitivity effect will gradually increase; when the pore pressure is less than 10 MPa, the permeability appears to increase significantly, and this is especially true for a pressure of 5 MPa. The main cause of this result is the slippage effect of gas seepage during the depletion of the gas reservoir, when the pore pressure is lower than a certain value. The valid stress changes of the core are not large, and the stress sensitivity is not strong, so the slippage effect plays a major role, which leads to an increase in the gas permeability during the late period of certain flow gas production.

Depression of freezing temperature of water and water solutions in porous materials

1989 ◽  
Vol 54 (10) ◽  
pp. 2644-2647 ◽  
Author(s):  
Petr Schneider ◽  
Jiří Rathouský
Keyword(s):  
Water Vapor ◽  
Porous Materials ◽  
Inorganic Salt ◽  
Freezing Point ◽  
Freezing Temperature ◽  
Inorganic Salts ◽  
Freezing Point Depression ◽  
Salt Solutions ◽  
Water Solutions

In porous materials filled with water or water solutions of inorganic salts, water freezes at lower temperatures than under normal conditions; the reason is the decrease of water vapor tension above the convex meniscus of liquid in pores. The freezing point depression is not very significant in pores with radii from 0.05 μm to 10 μm (about 0.01-2.5 K). Only in smaller pores, especially when filled with inorganic salt solutions, this depression is important.

scholarly journals Quantitative study on natural gas production risk of Carboniferous gas reservoir in eastern Sichuan

2021 ◽  
Author(s):  
Guo Yu ◽  
Haitao Li ◽  
Yanru Chen ◽  
Linqing Liu ◽  
Chenyu Wang ◽  
...  
Keyword(s):  
Risk Factors ◽  
Risk Factor ◽  
Natural Gas ◽  
Gas Production ◽  
Probability Method ◽  
Gas Reservoir ◽  
Production Risk ◽  
Probability Interval ◽  
Natural Gas Production ◽  
Stable Production

AbstractQuantifying natural gas production risk can help guide natural gas exploration and development in Carboniferous gas reservoirs. In this study, the Monte Carlo probability method is used to obtain the probability distribution and growth curve of each production risk factor and production in a Carboniferous gas reservoir in eastern Sichuan. In addition, the fuzzy comprehensive evaluation method is used to conduct the sensitivity analysis of the risk factors, and the natural gas production and realization probability under different risk factors are obtained. The research results show that: (1) the risk factor–production growth curve and probability distribution are calculated by the Monte Carlo probability method. The average annual production under the stable production stage under different realization probabilities is obtained. The maximum probability range of annual production is $$\left( {43.43 - 126.35} \right) \times 10^{8} {\text{m}}^{3} /{\text{year}}$$ 43.43 - 126.35 × 10 8 m 3 / year , and the probability range is 14.59–92.88%. (2) The risk factor sensitivity analysis is significantly affected by the probability interval. In the entire probability interval, the more sensitive risk factors are the average production of the kilometer-deep well (D) and the production rate in the stable production stage (A). During the exploration and development of natural gas, these two risk factors can be adjusted to increase production.

scholarly journals Effects of Isochoric Freezing Conditions on Cut Potato Quality

Foods ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 974
Author(s):  
Yuanheng Zhao ◽  
Cristina Bilbao-Sainz ◽  
Delilah Wood ◽  
Bor-Sen Chiou ◽  
Matthew J. Powell-Palm ◽  
...  
Keyword(s):  
Ascorbic Acid ◽  
Freezing Point ◽  
Freezing Temperature ◽  
Quality Attributes ◽  
Food Storage ◽  
Compression Rate ◽  
Beneficial Effects ◽  
C 71 ◽  
Frozen Potatoes ◽  
Full Factorial

Isochoric freezing is a pressure freezing technique that could be used to retain the beneficial effects of food storage at temperatures below their freezing point without ice damage. In this study, potato cylinders were frozen in an isochoric system and examined using full factorial combinations of three processing procedures (immersed in water, vacuum-packed and immersed in ascorbic acid solution), four freezing temperatures/pressures (−3 °C/37 MPa, −6 °C/71 MPa, −9 °C/101 MPa and −15 °C/156 MPa) and two average compression rates (less than 0.02 and more than 0.16 MPa/s). The effects of process variables on critical quality attributes of frozen potatoes after thawing were investigated, including mass change, volume change, water holding capacity, color and texture. Processing procedure and freezing temperature/pressure were found to be highly significant factors, whereas the significance of the compression rate was lower. For the processing procedures, immersion in an isotonic solution of 5% ascorbic acid best preserved quality attributes. At the highest pressure level of 156 MPa and low compression rate of 0.02 MPa/s, potato samples immersed in ascorbic acid retained their color, 98.5% mass and 84% elasticity modulus value. These samples also showed a 1% increase in volume and 13% increase in maximum stress due to pressure-induced hardening.

scholarly journals Co-gasification of different rank coals with biomass and petroleum coke in a high-pressure reactor for H2-rich gas production

2010 ◽  
Vol 101 (9) ◽  
pp. 3230-3235 ◽  
Author(s):  
J. Fermoso ◽  
B. Arias ◽  
M.V. Gil ◽  
M.G. Plaza ◽  
C. Pevida ◽  
...  
Keyword(s):  
High Pressure ◽  
Petroleum Coke ◽  
Gas Production

Application and Study of Fine-Silty Sand Control Technique Using Fiber-Complex High-Pressure Pack in Sebei Gas Reservoir

2006 ◽  
Author(s):  
Fujian Zhou ◽  
Yiping Zong ◽  
Yuzhang Liu ◽  
Xianyou Yang ◽  
Chunming Xiong ◽  
...  
Keyword(s):  
High Pressure ◽  
Silty Sand ◽  
Control Technique ◽  
Gas Reservoir ◽  
Sand Control

scholarly journals Drill core from seismically active sandstone gas reservoir yields clues to internal deformation mechanisms

Geology ◽  
2020 ◽  
Author(s):  
Berend A. Verberne ◽  
Suzanne J.T. Hangx ◽  
Ronald P.J. Pijnenburg ◽  
Maartje F. Hamers ◽  
Martyn R. Drury ◽  
...  
Keyword(s):  
Microstructural Analysis ◽  
Gas Production ◽  
Drill Core ◽  
Gas Reservoir ◽  
Gas Field ◽  
Reservoir Compaction ◽  
Key Factor ◽  
Forecasting System ◽  
Internal Deformation ◽  
Dauphiné Twinning

Europe’s largest gas field, the Groningen field (the Netherlands), is widely known for induced subsidence and seismicity caused by gas pressure depletion and associated compaction of the sandstone reservoir. Whether compaction is elastic or partly inelastic, as implied by recent experiments, is a key factor in forecasting system behavior and seismic hazard. We sought evidence for inelastic deformation through comparative microstructural analysis of unique drill core recovered from the seismogenic center of the field in 2015, 50 yr after gas production started, versus core recovered before production (1965). Quartz grain fracturing, crack healing, and stress-induced Dauphiné twinning are equally developed in the 2015 and 1965 cores, with the only measurable effect of gas production being enhanced microcracking of sparse K-feldspar grains in the 2015 core. Interpreting these grains as strain markers, we suggest that reservoir compaction involves elastic strain plus inelastic compression of weak clay films within grain contacts.

STUDY ON NEW ICE SLURRY GENERATOR USING NaCl AQUEOUS SOLUTION AT LOW CONCENTRATION

2013 ◽  
Vol 21 (01) ◽  
pp. 1350004 ◽  
Author(s):  
KOJI FUMOTO ◽  
TSUYOSHI KAWANAMI ◽  
TAKAO INAMURA
Keyword(s):  
Aqueous Solution ◽  
High Pressure ◽  
Test Section ◽  
Freezing Point ◽  
New Method ◽  
Heat Of Fusion ◽  
Test Fluid ◽  
Ice Slurry ◽  
Slurry Ice ◽  
Experimental Apparatus

A cold thermal energy storage system has been developed for HVAC. There are many ice-based cooling systems operating around the world. Ice slurry, which is a mixture of fine ice crystals and liquid water, is utilized in ice storage systems owing to its good flowability and large latent heat of fusion. For slurry ice production techniques, there are presently a number of commercially available ice slurry generators (e.g., Supercooled slurry ice generator, Scraper type generator, and Vacuum type generator, etc.). In the present study, a new method was developed to generate ice slurry without the deposition of an ice layer on a cooled surface. The basic components of the experimental apparatus is a cooling brine circulating loop, a high pressure pump, a valve, an aqueous solution flow loop containing the test section, which is made of transparent acrylic, and the associated instrumentation. This new method is based on freezing-point depression of the aqueous solution, which is maintained under high-pressure conditions. To control the timing for solidification and to generate ice slurry, we investigated the relationships among the pressure and temperature of the aqueous solution. The freezing phenomenon of the aqueous solution in the test section was observed in detail. As a result, we developed a new ice slurry generator based on the new method that controls the pressure and temperature of the aqueous solution. Experimental results showed that the characteristics of the ice slurry generation were closely related to the pressure and initial stage temperature of the test fluid. Finally, the optimum operation condition of the ice slurry generator based on visualization experiment was discussed.

scholarly journals Vertical Modification on Depth-Integrated Ice Shelf Water Plume Modeling Based on an Equilibrium Vertical Profile of Suspended Frazil Ice Concentration

2017 ◽  
Vol 47 (11) ◽  
pp. 2773-2792 ◽  
Author(s):  
Chen Cheng ◽  
Zhaomin Wang ◽  
Chengyan Liu ◽  
Ruibin Xia
Keyword(s):  
Freezing Point ◽  
Nonlinear Effects ◽  
Freezing Temperature ◽  
Shelf Water ◽  
Ice Shelf ◽  
Frazil Ice ◽  
Ice Concentration ◽  
Plume Modeling ◽  
Ice Shelf Water ◽  
Western Side

AbstractThe ice shelf water (ISW) plume is a prevalent phenomenon at the base of an ice shelf or sea ice adjacent to the ice shelf front. Such plumes may become supercooled and deposit marine ice when they rise. In the existing frazil ice–laden ISW plume models, it is generally assumed that supercooling and frazil ice growth can be adequately treated by using depth-averaged freezing temperature and vertically uniform frazil ice concentration within a plume. In reality, however, the temperature deficit and frazil ice concentration both increase toward the top of the plume. Hence, frazil crystals typically experience a greater deficit than that suggested by the plume’s temperature subtracted from its depth-averaged freezing point. In this study, the authors considered the combined nonlinear effects of vertical structures of frazil ice concentration and thermal forcing within an ISW plume by introducing equilibrium vertical profiles of frazil ice concentration into a horizontal two-dimensional depth-integrated ISW plume model. A series of idealized numerical experiments and an observation-based simulation beneath the western side of Ronne Ice Shelf have been conducted by using the vertically modified and original depth-integrated ISW plume models. It was found that the supercooled area, supercooling level, and suspended frazil ice and marine ice productivities are all substantially underestimated by the original models. Moreover, the differences are sensitive to the selected frazil ice size configuration. These results suggest that the vertical modification introduced in this study can significantly improve simulated marine ice distribution and its corresponding production, in comparison with those estimated by previous depth-integrated models.

Laboratory-Scale Investigation of the Utilisation of Multiple Flat-Fan Nozzles in Descaling Petroleum Production Tubing

2021 ◽  
Author(s):  
Kabir Hasan Yar'Adua ◽  
Idoko Job John ◽  
Abubakar Jibril Abbas ◽  
Salihu M. Suleiman ◽  
Abdullahi A. Ahmadu ◽  
...  
Keyword(s):  
High Pressure ◽  
Oil And Gas ◽  
Gas Production ◽  
Oil And Gas Production ◽  
Scale Removal ◽  
Petroleum Production ◽  
Well Completion ◽  
Water Jets ◽  
Well Integrity ◽  
Injection Pressures

Abstract Despite the recent wide embrace of mechanical descaling approaches for cleaning scales in petroleum production tubings and similar conduits with the use of high-pressure (HP) water jets, the process is still associated with downhole backpressure and well integrity challenges. While the introduction of sterling beads to replace sand particles in the water recorded high successes in maintaining well completion integrity after scale removal in some recent applications of this technique, it is, unfortunately, still not without questions of environmental degradation. Furthermore, the single nozzle, solids-free, aerated jetting descaling technique – recently published widely – is categorized with low scale surface area of contact, low descaling efficiency and subsequent high descaling rig time. The modifications to mechanical descaling techniques proposed in this work involve the use of three high-pressure flat fan nozzles of varying nozzles arrangements, standoff distances and injection pressures to remove soft scale deposits in oil and gas production tubings and similar circular conduits. This experiment provides further insights into the removal of paraffin scales of various shapes at different descaling conditions of injection pressures, stand-off distances and nozzle arrangements with the use of freshwater. The results obtained from this study also show consistency with findings from earlier works on the same subject.

Sign in / Sign up

Export Citation Format

Share Document