scholarly journals Equilibrium studies on the uptake of nitrate and phosphate ion onto low-cost adsorbent prepared via radiation-induced graft polymerization and hydrazine hydrate functionalization

2021 ◽  
Author(s):  
CHUKWUNONSO ANIAGOR ◽  
H.H. Sokker ◽  
A.I. Hashem ◽  
Y.M. El-Hamaki ◽  
M.H. El-Degwi ◽  
...  
Keyword(s):  
Hydrazine Hydrate ◽  
Cotton Fabric ◽  
Dimethyl Sulfate ◽  
Monomer Concentration ◽  
Isotherm Models ◽  
Equilibrium Studies ◽  
Batch Mode ◽  
Nitrate Ion ◽  
Phosphate Ion ◽  
Adsorption Affinity

Abstract In the study, cellulosic fabric waste-based anion exchanger (‘Cell-AE’), with abundant N+(CH3)2 functional groups were prepared by graft copolymerization of acrylonitrile (AN) onto cotton fabric waste using γ radiation 60Co, followed by chemical modification with hydrazine hydrate and alkylation with dimethyl sulfate. Factors affecting the grafting process, such as radiation dose and monomer concentration, was investigated. The main adsorbent (‘Cell-AE’) and its intermediate precursors were characterized using Fourier transform infrared spectroscopy (FTIR) and scan electron microscopy (SEM). The nitrate and phosphate sorption potentials of the Cell-AE further evaluated via batch mode. Based on the results obtained, ‘Cell-AE’ showed higher adsorption affinity towards phosphate ion (19.56 mg/g), when compared to that of the nitrate ion (11.23 mg/g). Similarly, the phosphate and nitrate ion adsorption onto ‘Cell-AE’ obeys both Dubinin–Radushkevich (D-R) and Redlich-Peterson (R-P) isotherm models, respectively. The present study conclusively proffered a potential mitigation approach to cotton fabric waste management.

scholarly journals Preparation of Chitosan/Hyperbranched Polyester/Cobalt Composite For Acid Blue 277 Dye Adsorption

2020 ◽  
Vol 11 (4) ◽  
pp. 11653-11665
Keyword(s):  
Particle Size ◽  
Dye Adsorption ◽  
Particle Size Analysis ◽  
Isotherm Models ◽  
Size Analysis ◽  
Order Kinetic ◽  
Hyperbranched Polyester ◽  
Acid Dye ◽  
Equilibrium Studies ◽  
Acid Blue

Acid dye effluents are among the popular threatening sources to the environment and human health due to their photochemical stability, complexity, and poor biodegradability. Therefore, this study aims to prepare chitosan/hyperbranched polyester (HBPE)/cobalt composite with ratio (1:1:0.5 wt %, respectively) using emulsion technique as an adsorbent to deal with the acid dye effluent. Chemical structure, morphology, particle size analysis, and thermal stability of the prepared composite were carried out using Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM),) dynamic light scattering technique (DLS) and thermogravimetric analysis (TGA). Adsorption isotherms of acid blue 277 dye (AB277), using the different isotherm models (Langmuir, Freundlich, D-R, and Temkin) under removal conditions at pH 3.0 and contact time of 1 h in 10 mL aqueous medium at 25ᴼC, were investigated. The results illustrated that the chitosan/HBPE/Co composite was successfully prepared with a particle size of around 679±494 nm relative to chitosan/HBPE (139±67.6 nm). Also, the pseudo-second-order kinetic model fitted better than the pseudo-first-order one for adsorption of AB277. Batch equilibrium studies showed that chitosan/HBPE/Co composite could be employed as an efficient adsorbent of AB277 dye with an adsorption capacity of 26.74 mg/g, relative to that of chitosan/HBPE (3.19 mg/g).

scholarly journals Removal of Cu(II) from Aqueous Solutions Using Amine-Doped Polyacrylonitrile Fibers

2020 ◽  
Vol 10 (5) ◽  
pp. 1738
Author(s):  
Kay Thwe Aung ◽  
Seung-Hee Hong ◽  
Seong-Jik Park ◽  
Chang-Gu Lee
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Naoh Solution ◽  
Surface Modified ◽  
Pan Fibers

Polyacrylonitrile (PAN) fibers were prepared via electrospinning and were modified with diethylenetriamine (DETA) to fabricate surface-modified PAN fibers. The surface-modified PAN fibers were used to evaluate their adsorption capacity for the removal of Cu(II) from aqueous solutions. Batch adsorption experiments were performed to examine the effects of the modification process, initial concentration, initial pH, and adsorbent dose on the adsorption of Cu(II). Kinetic analysis revealed that the experimental data fitted the pseudo-second-order kinetic model better than the pseudo-first-order model. Adsorption equilibrium studies were conducted using the Freundlich and Langmuir isotherm models, and the findings indicated that the PAN fibers modified with 85% DETA presented the highest adsorption capacity for Cu(II) of all analyzed samples. Moreover, the results revealed that the Freundlich model was more appropriate than the Langmuir one for describing the adsorption of Cu(II) onto the modified fibers at various initial Cu(II) concentrations. The maximum adsorption capacity was determined to be 87.77 mg/g at pH 4, and the percent removal of Cu(II) increased as the amount of adsorbent increased. Furthermore, the surface-modified PAN fibers could be easily regenerated using NaOH solution. Therefore, surface-modified PAN fibers could be used as adsorbents for the removal of Cu(II) from aqueous solutions.

scholarly journals Characterization of Residual Biomasses and Its Application for the Removal of Lead Ions from Aqueous Solution

2019 ◽  
Vol 9 (21) ◽  
pp. 4486 ◽  
Author(s):  
Candelaria Tejada-Tovar ◽  
Angel Darío Gonzalez-Delgado ◽  
Angel Villabona-Ortiz
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Mesoporous Structure ◽  
Isotherm Models ◽  
Solution Ph ◽  
Batch Mode ◽  
Suitable Alternative

The removal of water pollutants has been widely addressed for the conservation of the environment, and novel materials are being developed as adsorbent to address this issue. In this work, different residual biomasses were employed to prepare biosorbents applied to lead (Pb(II)) ion uptake. The choice of cassava peels (CP), banana peels (BP), yam peels (YP), and oil palm bagasse (OPB) was made due to the availability of such biomasses in the Department of Bolivar (Colombia), derived from agro-industrial activities. The materials were characterized by ultimate and proximate analysis, Fourier Transform Infrared Spectroscopy (FTIR), Brunauer-Emmett-Teller analysis (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive X-Ray Spectroscopy (EDS) in order to determine the physicochemical properties of bioadsorbents. The adsorption tests were carried out in batch mode, keeping the initial metal concentration at 100 ppm, temperature at 30 °C, particle size at 1 mm, and solution pH at 6. The experimental results were adjusted to kinetic and isotherm models to determine the adsorption mechanism. The remaining concentration of Pb(II) in solution was measured by atomic absorption at 217 nm. The functional groups identified in FTIR spectra are characteristic of lignocellulosic materials. A high surface area was found for all biomaterials with the exception of yam peels. A low pore volume and size, related to the mesoporous structure of these materials, make these bioadsorbents a suitable alternative for liquid phase adsorption, since they facilitate the diffusion of Pb(II) ions onto the adsorbent structure. Both FTIR and EDS techniques confirmed ion precipitation onto adsorbent materials after the adsorption process. The adsorption tests reported efficiency values above 80% for YP, BP, and CP, indicating a good uptake of Pb(II) ions from aqueous solution. The results reported that Freundlich isotherm and pseudo-second order best fit experimental data, suggesting that the adsorption process is governed by chemical reactions and multilayer uptake. The future prospective of this work lies in the identification of alternatives to reuse Pb(II)-contaminated biomasses after heavy metal adsorption, such as material immobilization.

ADSORPTION OF ACID ORANGE 7 BY CETYLPYRIDINIUM BROMIDE MODIFIED SUGARCANE BAGASSE

2016 ◽  
Vol 78 (1-2) ◽  
Author(s):  
Nik Ahmad Nizam Nik Malek ◽  
Nurain Mat Sihat ◽  
Mahmud A. S. Khalifa ◽  
Auni Afiqah Kamaru ◽  
Nor Suriani Sani
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Sugarcane Bagasse ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Acid Orange 7 ◽  
Cetylpyridinium Bromide ◽  
Batch Mode ◽  
Acid Orange ◽  
Adsorption Data

In the present study, the adsorption of acid orange 7 (AO7) dye from aqueous solution by sugarcane bagasse (SB) and cetylpyridinium bromide (CPBr) modified sugarcane bagasse (SBC) was examined. SBC was prepared by reacting SB with different concentrations (0.1, 1.0 and 4.0 mM) of cationic surfactant, CPBr. The SB and SBC were characterized using Fourier transform infrared (FTIR) spectroscopy. The adsorption experiments were carried out in a batch mode. The effect of initial AO7 concentrations (5-1000 mg/L), initial CPBr concentrations and pH of AO7 solution (2-9) on the adsorption capacity of SB and SBC were investigated. The experimental adsorption data were analyzed using Langmuir and Freundlich isotherm models. The adsorption of AO7 onto SB and SBC followed Freundlich and Langmuir isotherm models, respectively. The maximum uptake of AO7 was obtained by SBC4.0 (SB treated with 4.0 mMCPBr) with the adsorption capacity of 144.928 mg/g. The highest AO7 removal was found to be at pH 2 and 7 for SB and SBC, respectively. As a conclusion, sugarcane bagasse modified with CPBr can become an alternative adsorbent for the removal of anionic compounds in aqueous solution.

scholarly journals Equilibrium, Kinetics, and Thermodynamics of the Removal of Nickel(II) from Aqueous Solution Using Cow Hooves

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
I. Osasona ◽  
O. O. Ajayi ◽  
A. O. Adebayo
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Room Temperature ◽  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Equilibrium Data

The feasibility of using powdered cow hooves (CH) for removing Ni2+ from aqueous solution was investigated through batch studies. The study was conducted to determine the effect of pH, adsorbent dosage, contact time, adsorbent particle size, and temperature on the adsorption capacity of CH. Equilibrium studies were conducted using initial concentration of Ni2+ ranging from 15 to 100 mgL−1 at 208, 308, and 318 K, respectively. The results of our investigation at room temperature indicated that maximum adsorption of Ni2+ occurred at pH 7 and contact time of 20 minutes. The thermodynamics of the adsorption of Ni2+ onto CH showed that the process was spontaneous and endothermic. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to quantitatively analysed the equilibrium data. The equilibrium data were best fitted by Freundlich isotherm model, while the adsorption kinetics was well described by pseudo-second-order kinetic equation. The mean adsorption energy obtained from the D-R isotherm revealed that the adsorption process was dominated by physical adsorption. Powdered cow hooves could be utilized as a low-cost adsorbent at room temperature under the conditions of pH 7 and a contact time of 20 minutes for the removal of Ni(II) from aqueous solution.

scholarly journals Adsorption and equilibrium studies of phenol and para-nitrophenol by magnetic activated carbon synthesised from cauliflower waste

2019 ◽  
Vol 25 (5) ◽  
pp. 742-752 ◽  
Author(s):  
Nidhi Yadav ◽  
Dhruv Narayan Maddheshiaya ◽  
Shalu Rawat ◽  
Jiwan Singh
Keyword(s):  
Activated Carbon ◽  
Isotherm Models ◽  
X Ray Diffraction ◽  
Equilibrium Studies ◽  
First Order ◽  
Adsorbate Concentration ◽  
Adsorption Data ◽  
Pore Diffusion Model ◽  
Different Temperatures ◽  
Pseudo Second Order

In this study, waste cauliflower leaves were used for adsorbent preparation. The waste cauliflower leaves were converted into activated carbon by pyrolysis at two different temperatures 250˚C and 500˚C with magnetic property. The prepared adsorbents were denoted as CAC-250 and CAC-500 and characterized by the use of scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The adsorbents were applied for the removal of phenol and PNP from their aqueous solutions. The adsorption of phenol was found very less by the application CAC-250, whereas by the application of CAC-500 the adsorption of both phenol and PNP was enhanced. The maximum adsorption of phenol was found 99% and that of PNP was found ~100% using CAC-500, with initial adsorbate concentration 5 mg/L at 25˚C. The adsorption data was analysed with Langmuir, Freundlich and Temkin isotherm models and different kinetic models that are pseudo first order, pseudo second order, Elovich, intraparticle and pore diffusion model.

scholarly journals Removing Thallium (I) Ion from Aqueous Solutions Using Modified ZnO Nanopowder

2016 ◽  
Vol 11 (7) ◽  
pp. 3777-3788 ◽  
Author(s):  
H. Dashti Khavidaki ◽  
M. H. Fekri
Keyword(s):  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Phosphate Solution ◽  
Experimental Conditions ◽  
Batch Mode ◽  
Solution Interface ◽  
Zno Nanopowder ◽  
Exothermic Process ◽  
Initial Ph ◽  
Sodium Phosphate Solution

In this study, the adsorption of thallium (I) ion as a dangerous pollutant from aqueous solution onto modified ZnO nanopowder as a fairly cheap adsorbent has been examined in batch mode. It was known that modification of the adsorbent was necessary to reach a significant adsorption percentage. The adsorbent used here was modified by sodium phosphate solution. The effect of experimental conditions such as initial pH of solution, contact time, adsorbent dosage, initial concentration of thallium and temperature is studied. The results showed the dependence of the adsorption percentage to these conditions specially its pH. The maximum adsorption percentage of Tl (I) ions at 25±1oC was 92.8%. Freundlich isotherm model provided a better fit with the experimental data than Langmuir and Temkin isotherm models by high correlation. Separation factor, RL, values showed that modified ZnO nanopowder was favorable for the adsorption of Tl (I) ion. The negative value of ΔH0 showed that Tl (I) sorption is an exothermic process and the negative value of ΔS0 represented that there is a little decrease of randomness at the solid-solution interface during sorption.

scholarly journals SIMULTANEOUS ADSORPTION OF TETRACYCLINE AND AMOXICILLIN BY CLADOPHORA AND SPIRULINA ALGAE BIOMASS

2021 ◽  
Vol 52 (5) ◽  
pp. 1290-1303
Author(s):  
I. N. Abd ◽  
M. J. Mohammed-Ridha
Keyword(s):  
Low Cost ◽  
Agitation Speed ◽  
Langmuir Model ◽  
Coefficient Of Determination ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Batch Mode ◽  
Algae Biomass ◽  
Initial Ph ◽  
Biomass Dosage

Adsorption studies were performed at different initial Tetracycline (TC) and Amoxicillin (AMO) concentration, different biomass dosage and type, contact time, agitation speed, and initial pH.  In the batch mode were investigated. The optimum pH of solutions is 6.5 for TC and 5 for AMO, agitation speed 200 rpm and concentration 50 ppm. The results in FTIR showed that there were -OH and amides (N-H) and other functional groups on the surface of Cladophora and Spirulina algae. The equilibrium isotherm data were modeled with Freundlich, Temkin, and Langmuir isotherm models. The data best fitted with the Langmuir model. The maximal adsorption capacity from the Langmuir model was (9.86, 20. 5 mg/g) for TC and (7.89, 17.4 mg/g) for AMO on Cladophora and Spirulina algae, respectively. Finally, the pseudo-second-order kinetic model was best fitted the experimental kinetic data of TC and AMO onto Cladophora and Spirulina algae biomass with a high coefficient of determination between 0.97 and 0.99.    Cladophora and Spirulina algae, low-cost and eco-friendly adsorbents, can be used to adsorb the TC and AMO from the solution.

scholarly journals Removal of Textile Dyes by Chemically Treated Sawdust of Acacia: Kinetic and Equilibrium Studies

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Hanane Tounsadi ◽  
Yousra Metarfi ◽  
Noureddine Barka ◽  
Mustapha Taleb ◽  
Zakia Rais
Keyword(s):  
Textile Industry ◽  
Freundlich Isotherm ◽  
Physicochemical Characteristics ◽  
Textile Dyes ◽  
Isotherm Models ◽  
Synthetic Dyes ◽  
Equilibrium Studies ◽  
Biosorption Process ◽  
Chemically Treated ◽  
Equilibrium Data

Sawdust of acacia tree has been successfully used to remove textile dyes from wastewater due to its good sorption properties and its good chemical stability. Two materials are prepared by chemical treatment, including acidic and basic sawdust of acacia. The biosorption tests were carried out on two synthetic dyes of textile which are methylene blue (MB) and brilliant blue (BB). Efficient removal of the both dyes has been achieved by the basic treated sawdust acacia. The modeling of biosorption kinetic shows that the biosorption of MB and that of BB are well described by the pseudo-first-order model for both the chemically treated biosorbents. Equilibrium data have also established using Langmuir and Freundlich isotherm models. Langmuir biosorption capacities are 8.13 and 267.04 mg/g onto basic sawdust acacia and 6.19 and 230.76 mg/g onto acidic sawdust acacia, respectively, for BB and MB sorption. A real final effluent of a textile industry was treated by sorption on both biosorbent basis of sawdust acacia. In fact, the kinetic sorption was rapid with a mass ratio of 1 g/L. However, the biosorption process combined with a biological treatment provides a better result through the physicochemical characteristics of the studied effluent.

scholarly journals Glyphosate adsorption by Eucalyptus camaldulensis bark-mediated char and optimization through response surface modeling

2019 ◽  
Vol 9 (7) ◽  
Author(s):  
Kamalesh Sen ◽  
Jayanta Kumar Datta ◽  
Naba Kumar Mondal
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Low Cost ◽  
Eucalyptus Camaldulensis ◽  
Zero Point ◽  
Isotherm Models ◽  
Multilayer Adsorption ◽  
Batch Mode ◽  
Initial Concentration ◽  
Glyphosate Herbicide

Abstract In this study, orthophosphoric acid-modified activated char was prepared from Eucalyptus camaldulensis bark (EBAC), and used for removing traces of [N-(phosphonomethyl)glycine] (glyphosate) herbicide from aqueous solution. The adsorption capacity was characterized by zero-point-charge pH, surface analysis, and Fourier transform infrared spectroscopy. Batch mode experiments were conducted to observe the effects of selected variables, namely dose, contact time, pH, temperature, and initial concentration, on adsorption capacity. Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm models were generated to describe the mechanisms involved in the multilayer adsorption process. The results show that high temperature enhanced the adsorption capacity of EBAC, with a temperature of 373 K yielding adsorption capacity (qmax) and Freundlich parameter (KF) of 66.76 mg g−1 and 9.64 (mg g−1) (L mg−1)−n, respectively. The thermodynamics study revealed entropy and enthalpy of −5281.3 J mol−1 and −20.416 J mol−1, respectively. Finally, glyphosate adsorption was optimized by the Box–Behnken model, and optimal conditions were recorded as initial concentration of 20.28 mg L−1, pH 10.18, adsorbent dose of 199.92 mg/50 mL, temperature of 303.23 K, and contact time of 78.42 min, with removal efficiency of 98%. Therefore, it can be suggested that EBAC could be used as an efficient, low-cost adsorbent for removal of glyphosate from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document