Pervaporative desalination of seawater using a polyvinylidene fluoride based membrane

2017 ◽  
Vol 18 (5) ◽  
pp. 1674-1681 ◽  
Author(s):  
F. U. Nigiz ◽  
N. D. Hilmioglu
Keyword(s):  
Fresh Water ◽  
Polyvinylidene Fluoride ◽  
High Performance ◽  
Potable Water ◽  
Effective Properties ◽  
Cost Effective ◽  
Porous Membranes ◽  
Scientific Investigations ◽  
Different Temperatures ◽  
Energy Strategies

Abstract Producing a fresh water supply by converting non-potable water is an attractive solution when water is scarce. According to the energy strategies of different countries, various seawater purification techniques such as distillation and reverse osmosis (RO) are used to produce fresh water. Due to the selective separation capability and cost-effective properties, membrane based methods such as RO, electrodialysis, and ultra/micro/nano/filtration are prevalent, especially in Europe. Recently, innovative desalination technologies have been investigated by researchers. Among them, pervaporative separation, in which non-porous membranes are used, appears to be an emerging and promising method. The key part of the system is the membrane. Hence, scientific investigations are focused on the production of high-performance membranes. In this study, non-porous polyvinylidene fluoride (PVDF) and polyvinyl pyrrolidone (PVP) blend membranes were prepared in different PVDF/PVP ratios and Marmara seawater was desalinated using the pervaporation method at different temperatures. Desalination performance was evaluated as a function of flux and salt retention. The highest salt retention of 99.90% and flux of 1.60 kg/m2.h were obtained at 60 °C when the PVDF/PVP ratio was 1.5.

scholarly journals Performance of Oxalic Acid-Chitosan/Alumina Ceramic Biocomposite for the Adsorption of a Reactive Anionic Azo Dye

2021 ◽  
Author(s):  
John Pérez-Calderón ◽  
Alberto Scian ◽  
Martin Ducos ◽  
Victoria Santos ◽  
Noemi Elisabet Zaritzky
Keyword(s):  
Oxalic Acid ◽  
Adsorption Capacity ◽  
Azo Dye ◽  
High Performance ◽  
Inorganic Ions ◽  
Cost Effective ◽  
Maximum Adsorption Capacity ◽  
Physico Chemical ◽  
The Matrix ◽  
Different Temperatures

Abstract A biocomposite system was developed and tested for the removal of the azo dye Reative Red (RR195) from wastewater. The biocomposite was synthesized using ceramic particles containing 75% alumina which were coated using chitosan crosslinked with oxalic acid. The biocomposite showed high performance at low pH (maximum adsorption capacity = 345.3mg.g− 1 at pH = 2). The physico-chemical and structure characteristics of the matrix were evaluated by Z-potential, FTIR-ATR, SEM-EDS, DRX and porosity. Langmuir sorption isotherm and Pseudo Second order model gave the best fit. The electrostatic interaction between RR195 (due to the sulfonate groups) and the free amino groups of chitosan, enabled successive desorption/regeneration cycles. The maximum removal percentage (> 80%) occurred at pH = 2 due to the crosslinking effect. Experiments at different temperatures allowed the calculation of thermodynamic parameters (ΔG, ΔS, ΔH); adsorption was spontaneous, exothermic and enthalpy controlled. The presence of inorganic ions (NO3−>Cl−) was analyzed during the adsorption process. This novel biocomposite can be applied as a cost-effective and environmentally friendly adsorbent for anionic azo dye removal from wastewater. The application of chitosan crosslinked with oxalic acid as a coating of the ceramic support enhanced the adsorption capacity and enabled its use under acidic conditions without solubilization.

Microstructure of sputter deposited Ni-Sb ohmic contacts on GaAs

1989 ◽  
Vol 47 ◽  
pp. 450-451
Author(s):  
S. Yegnasubramanian ◽  
V.C. Kannan ◽  
R. Dutto ◽  
P.J. Sakach
Keyword(s):  
High Performance ◽  
Ohmic Contacts ◽  
Surface Defects ◽  
Pure Metal ◽  
Device Fabrication ◽  
Native Oxide ◽  
Metal Thin Films ◽  
Recent Developments ◽  
Different Temperatures ◽  
Sputter Deposited

Recent developments in the fabrication of high performance GaAs devices impose crucial requirements of low resistance ohmic contacts with excellent contact properties such as, thermal stability, contact resistivity, contact depth, Schottky barrier height etc. The nature of the interface plays an important role in the stability of the contacts due to problems associated with interdiffusion and compound formation at the interface during device fabrication. Contacts of pure metal thin films on GaAs are not desirable due to the presence of the native oxide and surface defects at the interface. Nickel has been used as a contact metal on GaAs and has been found to be reactive at low temperatures. Formation Of Ni2 GaAs at 200 - 350C is reported and is found to grow epitaxially on (001) and on (111) GaAs, but is shown to be unstable at 450C. This paper reports the investigations carried out to understand the microstructure, nature of the interface and composition of sputter deposited and annealed (at different temperatures) Ni-Sb ohmic contacts on GaAs by TEM. Attempts were made to correlate the electrical properties of the films such as the sheet resistance and contact resistance, with the microstructure. The observations are corroborated by Scanning Auger Microprobe (SAM) investigations.

Mineral/microfibrillated cellulose composite materials: High performance products, applications, and product forms

TAPPI Journal ◽  
2018 ◽  
Vol 17 (09) ◽  
pp. 507-515 ◽  
Author(s):  
David Skuse ◽  
Mark Windebank ◽  
Tafadzwa Motsi ◽  
Guillaume Tellier
Keyword(s):  
Composite Materials ◽  
High Performance ◽  
Aqueous Suspension ◽  
Production Capacity ◽  
Cost Savings ◽  
Cost Effective ◽  
New Materials ◽  
Wet Strength ◽  
Product Forms ◽  
Cellulose Composite

When pulp and minerals are co-processed in aqueous suspension, the mineral acts as a grinding aid, facilitating the cost-effective production of fibrils. Furthermore, this processing allows the utilization of robust industrial milling equipment. There are 40000 dry metric tons of mineral/microfbrillated (MFC) cellulose composite production capacity in operation across three continents. These mineral/MFC products have been cleared by the FDA for use as a dry and wet strength agent in coated and uncoated food contact paper and paperboard applications. We have previously reported that use of these mineral/MFC composite materials in fiber-based applications allows generally improved wet and dry mechanical properties with concomitant opportunities for cost savings, property improvements, or grade developments and that the materials can be prepared using a range of fibers and minerals. Here, we: (1) report the development of new products that offer improved performance, (2) compare the performance of these new materials with that of a range of other nanocellulosic material types, (3) illustrate the performance of these new materials in reinforcement (paper and board) and viscosification applications, and (4) discuss product form requirements for different applications.

Parallel Computing for Tire Simulations

2011 ◽  
Vol 39 (3) ◽  
pp. 193-209 ◽  
Author(s):  
H. Surendranath ◽  
M. Dunbar
Keyword(s):  
High Performance ◽  
Effective Means ◽  
Cost Effective ◽  
Turnaround Time ◽  
Careful Consideration ◽  
Rolling Contact ◽  
Element Analysis ◽  
Parallel Solvers ◽  
Design Changes ◽  
Highly Nonlinear

Abstract Over the last few decades, finite element analysis has become an integral part of the overall tire design process. Engineers need to perform a number of different simulations to evaluate new designs and study the effect of proposed design changes. However, tires pose formidable simulation challenges due to the presence of highly nonlinear rubber compounds, embedded reinforcements, complex tread geometries, rolling contact, and large deformations. Accurate simulation requires careful consideration of these factors, resulting in the extensive turnaround time, often times prolonging the design cycle. Therefore, it is extremely critical to explore means to reduce the turnaround time while producing reliable results. Compute clusters have recently become a cost effective means to perform high performance computing (HPC). Distributed memory parallel solvers designed to take advantage of compute clusters have become increasingly popular. In this paper, we examine the use of HPC for various tire simulations and demonstrate how it can significantly reduce simulation turnaround time. Abaqus/Standard is used for routine tire simulations like footprint and steady state rolling. Abaqus/Explicit is used for transient rolling and hydroplaning simulations. The run times and scaling data corresponding to models of various sizes and complexity are presented.

Azo (Hydrazone) pigments: general principles

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Robert Christie
Keyword(s):  
High Performance ◽  
Metal Salt ◽  
Low Cost ◽  
Cost Effective ◽  
Precipitation Process ◽  
Ambient Temperatures ◽  
Technical Performance ◽  
Chemical Structures ◽  
General Chemical ◽  
Physical Form

Abstract This paper presents an overview of the general chemical principles underlying the structures, synthesis and technical performance of azo pigments, the dominant chemical class of industrial organic pigments in the yellow, orange, and red shade areas, both numerically and in terms of tonnage manufactured. A description of the most significant historical features in this group of pigments is provided, starting from the discovery of the chemistry on which azo colorants are based by Griess in the mid-nineteenth century, through the commercial introduction of the most important classical azo pigments in the early twentieth century, including products known as the Hansa Yellows, β-naphthol reds, including metal salt pigments, and the diarylide yellows and oranges, to the development in the 1950s and 1960s of two classes of azo pigments that exhibit high performance, disazo condensation pigments and benzimidazolone-based azo pigments. A feature that complicates the description of the chemical structures of azo pigments is that they exist in the solid state as the ketohydrazone rather than the hydroxyazo form, in which they have been traditionally been illustrated. Numerous structural studies conducted over the years on an extensive range of azo pigments have demonstrated this feature. In this text, they are referred to throughout as azo (hydrazone) pigments. Since a common synthetic procedure is used in the manufacture of virtually all azo (hydrazone) pigments, this is discussed in some detail, including practical aspects. The procedure brings together two organic components as the fundamental starting materials, a diazo component and a coupling component. An important reason for the dominance of azo (hydrazone) pigments is that they are highly cost-effective. The syntheses generally involve low cost, commodity organic starting materials and are carried out in water as the reaction solvent, which offers obvious economic and environmental advantages. The versatility of the approach means that an immense number of products may be prepared, so that they have been adapted structurally to meet the requirements of many applications. On an industrial scale, the processes are straightforward, making use of simple, multi-purpose chemical plant. Azo pigments may be produced in virtually quantitative yields and the processes are carried out at or below ambient temperatures, thus presenting low energy requirements. Finally, provided that careful control of the reaction conditions is maintained, azo pigments may be prepared directly by an aqueous precipitation process that can optimise physical form, with control of particle size distribution, crystalline structure, and surface character. The applications of azo pigments are outlined, with more detail reserved for subsequent papers on individual products.

scholarly journals Development of Quantum Dot (QD) Based Color Converters for Multicolor Display

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1089
Author(s):  
Muhammad T. Sajjad ◽  
Ashu K. Bansal ◽  
Francesco Antolini ◽  
Eduard Preis ◽  
Lenuta Stroea ◽  
...  
Keyword(s):  
Polymer Matrix ◽  
Cost Effective ◽  
Final Size ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Color Displays ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Color Conversion ◽  
Temperature Time

Many displays involve the use of color conversion layers. QDs are attractive candidates as color converters because of their easy processability, tuneable optical properties, high photoluminescence quantum yield, and good stability. Here, we show that emissive QDs with narrow emission range can be made in-situ in a polymer matrix, with properties useful for color conversion. This was achieved by blending the blue-emitting pyridine based polymer with a cadmium selenide precursor and baking their films at different temperatures. To achieve efficient color conversion, blend ratio and baking temperature/time were varied. We found that thermal decomposition of the precursor leads to highly emissive QDs whose final size and emission can be controlled using baking temperature/time. The formation of the QDs inside the polymer matrix was confirmed through morphological studies using atomic force microscopy (AFM) and transmission electron microscopy (TEM). Hence, our approach provides a cost-effective route to making highly emissive color converters for multi-color displays.

Robustness versus Performance Assessment for Different Gamma-TiAl Processing Routes

2011 ◽  
Vol 1295 ◽  
Author(s):  
Marc Thomas
Keyword(s):  
High Performance ◽  
Cost Effective ◽  
Processing Route ◽  
Transportation Industry ◽  
Tial Alloys ◽  
Alternative Processing ◽  
Aerospace Applications ◽  
Robust Processing ◽  
Processing Techniques ◽  
Robust Process

ABSTRACTOne of the main driving force for the development of advanced structural materials is weight saving especially in the transportation industry in order to reduce CO2 emission. The utilization of gamma aluminides, as good candidates for aerospace applications, is strongly related to the development of a cost-effective and robust processing route, as far as possible. It is well established that the processing route, i.e. cast, wrought or PM, has a dramatic effect on the microstructure and texture of gamma-TiAl alloys. Therefore, significant microstructural variations through post-heat treatments coupled with compositional modifications can only guarantee a proper balance of desired properties. However, a number of metallurgical factors during the processing steps can contribute to some scattering in properties. This review will highlight several critical process variables in terms of the resulting g-TiAl microstructures. Of primary importance is the as-cast texture which is difficult to control and may contribute to prefer some alternative processing routes to ensure a better repeatability in mechanical results. Some innovative processing techniques for controlling the structure will then be presented. The main point which will be discussed in this paper is whether an approach leading to a robust process would not be at the expense of the high performance of the structural material.

scholarly journals Rapid Detection and Quantification of Patulin and Citrinin Contamination in Fruits

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4545
Author(s):  
Sudharsan Sadhasivam ◽  
Omer Barda ◽  
Varda Zakin ◽  
Ram Reifen ◽  
Edward Sionov
Keyword(s):  
High Performance ◽  
Cost Effective ◽  
Hplc Method ◽  
Pear Fruit ◽  
Cost Effective Method ◽  
Fruit Samples ◽  
Pome Fruits ◽  
Reliable Methods ◽  
By Products ◽  
Detection And Quantification

Patulin (PAT) and citrinin (CTN) are the most common mycotoxins produced by Penicillium and Aspergillus species and are often associated with fruits and fruit by-products. Hence, simple and reliable methods for monitoring these toxins in foodstuffs are required for regular quality assessment. In this study, we aimed to establish a cost-effective method for detection and quantification of PAT and CTN in pome fruits, such as apples and pears, using high-performance liquid chromatography (HPLC) coupled with spectroscopic detectors without the need for any clean-up steps. The method showed good performance in the analysis of these mycotoxins in apple and pear fruit samples with recovery ranges of 55–97% for PAT and 84–101% for CTN, respectively. The limits of detection (LOD) of PAT and CTN in fruits were 0.006 µg/g and 0.001 µg/g, while their limits of quantification (LOQ) were 0.018 µg/g and 0.003 µg/g, respectively. The present findings indicate that the newly developed HPLC method provides rapid and accurate detection of PAT and CTN in fruits.

Sign in / Sign up

Export Citation Format

Share Document