scholarly journals Biogas Production from Sugarcane Vinasse: A Review

2021 ◽  
Vol 12 (2) ◽  
pp. 34-44
Author(s):  
Rustiana Yuliasni ◽  
Rieke Yuliastuti ◽  
Nanik Indah Setianingsih
Keyword(s):  
Biogas Production ◽  
Renewable Energy Sources ◽  
Organic Load ◽  
Full Potential ◽  
High Concentration ◽  
Biogas Yield ◽  
Methane Potential ◽  
Pre Treatment ◽  
Sugarcane Vinasse

Biogas is a renewable energy sources that could replace the role of fossil fuel. Biogas could be produced from biomass or agro-industrial wastewater. Sugarcane vinasse has potential of biogas production due to its high BOD concentration (10–65 g BOD/l). However, the biogas production from sugarcane vinasse has several drawbacks that hinders the maximum biogas yield, such as: acidic pH (pH 3.5 – 5.0), high temperature (80–90°C) and high concentration of sulfuric acid (> 150 mg/L). Theoretically, the methane potential per gram COD is 0.35 L/gr COD, containing of 60% methane. However, up to date, the maximum biogas production from vinasse was less then its theoretical value. To get the full potential of biogas production from vinasse wastewater as well as to reduce the capital cost for full scale application, combination of suitable pre-treatment, selected microorganisms and bioreactor design-configuration are the most important parameters to be considered. This paper aims to explore the potential of sugarcane vinasse to produce biogas, by elaborating the aforementioned key parameters. In this review the basic characteristic and the potency of sugarcane vinasse wastewater will be elaborated.  Furthermore, the effect of key parameters such as pH, temperature, and organic load to biogas production will also be discussed. The biogas technology will also be explored. Lastly, conclusion will be determined

scholarly journals Opportunity of Biogas Production from Solid Organic Wastes through Anaerobic Digestion

2018 ◽  
Vol 65 ◽  
pp. 05025 ◽  
Author(s):  
Sagor Kumar Pramanik ◽  
Fatihah Binti Suja ◽  
Biplob Kumar Pramanik ◽  
Shahrom Bindi Md Zain
Keyword(s):  
Anaerobic Digestion ◽  
Biogas Production ◽  
Nutrient Balance ◽  
Organic Wastes ◽  
Organic Loading Rate ◽  
Biogas Yield ◽  
Carbon And Nitrogen ◽  
Potential Risks ◽  
Nitrogen Ratio ◽  
Pre Treatment

Solid organic wastes create potential risks to environmental pollution and human health due to the uncontrolled discharge of huge quantities of hazardous wastes from numerous sources. Now-a-days, anaerobic digestion (AD) is considered as a verified and effective alternative compared to other techniques for treating solid organic waste. The paper reviewed the biological process and parameters involved in the AD along with the factors could enhance the AD process. Hydrolysis is considered as a rate-limiting phase in the complex AD process. The performance and stability of AD process is highly influenced by various operating parameters like temperature, pH, carbon and nitrogen ratio, retention time, and organic loading rate. Different pre-treatment (e.g. mechanical, chemical and biological) could enhance the AD process and the biogas yield. Co-digestion can also be used to provide suitable nutrient balance inside the digester. Challenges of the anaerobic digestion for biogas production are also discussed.

Effect of Ultrasonic Pretreatment for the Anaerobic Digestion of Sewage Sludge

2012 ◽  
Vol 531 ◽  
pp. 528-531 ◽  
Author(s):  
Na Wei
Keyword(s):  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
High Concentration ◽  
Ultrasonic Pretreatment ◽  
Soluble Chemical Oxygen Demand ◽  
Pre Treatment ◽  
Settling Characteristics

Anaerobic digestion is an economic and environmentally friendly technology for treating the biomass material-sewage sludge, but has some limitations, such as the low efficient biogass production. In this paper ultrasound was proposed as pre-treatment for effective sludge anaerobic digestion. Sludge anaerobic digestion experiments with ultrasonic pretreatment was investigated. It can be seen that this treatment effectively leaded to the increase of soluble chemical oxygen demand(SCOD) and volatile fatty acids(VFA)concentration. High concentration of VFA leaded to a increase in biogas production. Besides, the SV of sludge was reduced and the settling characteristics of sludge was improved after ultrasonic pretreatment. It can be concluded that sludge anaerobic digestion with ultrasonic pretreatment is an effective method for biomass material transformation.

scholarly journals Effect of Thermal Pretreatment on the Yield of Biogas from Microcoleous Vaginatus

2021 ◽  
Vol 17 (4) ◽  
pp. 250-256
Author(s):  
M. Haruna ◽  
O.R. Momoh ◽  
S. Bilal
Keyword(s):  
Cell Wall ◽  
Anaerobic Digestion ◽  
Biogas Production ◽  
Renewable Energy Sources ◽  
Research Work ◽  
Proximate Analysis ◽  
Biogas Yield ◽  
Bacteria Growth ◽  
Positive Effect ◽  
Made In

Biomass is being looked upon as one of the promising renewable energy sources for the future, with growing interest in microalgae conversion into biogas through anaerobic digestion. Recently, the ability of microalgae to treat waste water has doubled its potentials material today. However, in spite of the progress made in that regards, there are still challenges of algae conversion to biofuel, due to the presence of complex cell wall in some algae. Cell wall inhibits bacteria growth during degradation. In this research work 10 grams of Microcoleous vaginatus was treated in an oven at varying temperatures of 70, 75 and 80 oC for an hour, out of which 4 g was measured into 250 ml serum bottle for digestion at mesophilic temperature of 37 oC. Based on the results of proximate analysis, 69%increase in carbohydrate was attained with 72.7 – 148% reduction in moisture content. The biogas yield of untreated sample was 4.36 mLg−1 VS, while, pretreated samples at 70, 75 and 80 ℃ produced 8.39, 9.07 and 9.38 mLg−1VS (volatile solid) of biogas. This  corresponds to 92, 108 and 115% higher than that of untreated samples. However, thermal treatment of M. vaginatus prior to digestion show positive effect on carbohydrate extraction and enhanced biogas and methane yield as well. Therefore, this makes the substrate a good feedstock for biogas production. Keywords: Biomass, pretreatment, thermal, anaerobic digestion, degradation, Microcoleous vaginatus.

scholarly journals Biological And Thermal Pretreatment Of Lignocellulosic Materials For Enhanced Biogas Production

2021 ◽  
Author(s):  
Samer Dahahda
Keyword(s):  
Anaerobic Digestion ◽  
Organic Material ◽  
Fossil Fuels ◽  
Biogas Production ◽  
Renewable Energy Sources ◽  
Current Status ◽  
Lignocellulosic Materials ◽  
Thermal Pretreatment ◽  
Biological Pretreatment ◽  
Biogas Yield

The rapid depletion of natural resources and the environmental concerns associated with the use of fossil fuels as the main source of global energy is leading to an increased interest in alternative and renewable energy sources. Lignocellulosic biomass is the most abundant source of organic materials that can be utilized as an energy source. Anaerobic digestion has been proven to be an effective technology for converting organic material into energy products such as biogas. However, the nature of lignocellulosic materials hinders the ability of microorganisms in an anaerobic digestion process to degrade and convert organic material to biogas. Therefore, a pretreatment step is necessary to improve the degradability of lignocellulosic materials and achieve higher biogas yield. Several pretreatment methods have been studied over the past few years including physical, thermal, chemical and biological pretreatment. This paper reviews biological and thermal pretreatment as two main promising methods used to improve biogas production from lignocelluloses. A greater focus is given on enzymatic pretreatment which is one of the promising yet under-researched biological pretreatment method. The paper addresses challenges in degrading lignocellulosic materials and the current status of research to improve biogas yield from lignocelluloses through biological and thermal pretreatment.

Screening of Factors Affecting Pre-Treatment by Ammonia-N Removal from Poultry Manure Wastewater by Using Soil Water to Improve Biogas Production

2015 ◽  
Vol 1107 ◽  
pp. 359-364
Author(s):  
Nina Farhana Mohd Jamaludin ◽  
Norazwina Zainol
Keyword(s):  
Reaction Time ◽  
Soil Water ◽  
Treatment Condition ◽  
Biogas Production ◽  
Peat Soil ◽  
Poultry Manure ◽  
Factors Affecting ◽  
Biogas Yield ◽  
N Removal ◽  
Pre Treatment

In this study, best pre-treatment condition of poultry manure wastewater (PMW) was determined from factorial analysis for the purpose of improving biogas production. Five factors were chosen for factorial screening namely: agitation (0 or 200 rpm), reaction time (2 to 5 hours), type of soil (peat soil or poultry farm soil), soil to water ratio (1:1 or 1:4) and PMW to soil water (SW) ratio (1:4 or 2:3). Based on the result, agitation gave highest contribution in pre-treatment of PMW at 38.36% followed by PMW to SW ratio at 29.76% contribution. In term of interaction, agitation and reaction gave the highest contribution to pre-treatment of PMW at 3.33% contribution. The best pre-treatment condition suggested by Design Expert software was using peat soil as source of soil at SW ratio of 1:6, and mixed with PMW at 1:4 ratio without agitation for 5 hours reaction time. Application of this best pre-treatment condition showed improvement in biogas yield by 82 % from 0.0045 L/g COD using untreated PMW to 0.0248 L/g COD using treated PMW.

scholarly journals Influence of Microwave Pre-Treatment on the Digestion and Higienisation of Waste Activated Sludge/Wpływ Dezintegracji Mikrofalowej Na Proces Fermentacji Oraz Higienizacji Nadmiernych Osadów Ściekowych

2014 ◽  
Vol 21 (3) ◽  
pp. 447-464 ◽  
Author(s):  
Jolanta Bohdziewicz ◽  
Mariusz Kuglarz ◽  
Klaudiusz Grűbel
Keyword(s):  
Anaerobic Digestion ◽  
Microwave Irradiation ◽  
Treatment Effectiveness ◽  
Biogas Production ◽  
Salmonella Spp ◽  
Biogas Yield ◽  
Treatment Conditions ◽  
Higher Power ◽  
Pre Treatment ◽  
Treatment Step

Abstract The article presents the results of determining the most appropriate conditions of microwave sludge pre-treatment (500-1200 W), prior to its anaerobic digestion in a continuous mode. The assessment of the pre-treatment conditions (microwave power, sludge temperature after pre-treatment) was based on: the release of organic (COD, protein) and inorganic (NH4+, PO43-) substances into liquid, the quantity of methane produced, sludge higienisation and the susceptibility of the pre-treated sludge to dewatering. The power of the microwaves applied did not play significant role on the pre-treatment effectiveness. Taking into account the fact that sludge pre-treatment by microwave irradiation requires the delivery of energy, the pre-treatment by microwaves of higher power (1200 W) and resulting in sludge temperature of 70°C was recommended for further experiments. Sludge pre-treatment by means of microwave irradiation as a pre-treatment step influenced the effectiveness of the subsequent anaerobic digestion, conducted in continuous conditions, in a positive way. The largest amount of biogas was obtained for HRT in the range of 15-20 days. As compared to the sludge which did not undergo pre-treatment, daily biogas production and biogas yield increased by 18-41% and 13-35% respectively. The combination of microwave pre-treatment and mesophilic anaerobic digestion ensured the elimination of pathogens (Salmonella spp., Escherichia coli).

scholarly journals Optimization of biogas yield from lignocellulosic materials with different pretreatment methods: a review

2021 ◽  
Vol 14 (1) ◽  
Author(s):  
Kehinde Oladoke Olatunji ◽  
Noor A. Ahmed ◽  
Oyetola Ogunkunle
Keyword(s):  
Renewable Energy ◽  
Energy Demand ◽  
Greenhouse Gas Emission ◽  
Anaerobic Fermentation ◽  
Biogas Production ◽  
Renewable Energy Sources ◽  
High Energy ◽  
Population Increase ◽  
Energy Sources ◽  
Biogas Yield

AbstractPopulation increase and industrialization has resulted in high energy demand and consumptions, and presently, fossil fuels are the major source of staple energy, supplying 80% of the entire consumption. This has contributed immensely to the greenhouse gas emission and leading to global warming, and as a result of this, there is a tremendous urgency to investigate and improve fresh and renewable energy sources worldwide. One of such renewable energy sources is biogas that is generated by anaerobic fermentation that uses different wastes such as agricultural residues, animal manure, and other organic wastes. During anaerobic digestion, hydrolysis of substrates is regarded as the most crucial stage in the process of biogas generation. However, this process is not always efficient because of the domineering stableness of substrates to enzymatic or bacteria assaults, but substrates’ pretreatment before biogas production will enhance biogas production. The principal objective of pretreatments is to ease the accessibility of the enzymes to the lignin, cellulose, and hemicellulose which leads to degradation of the substrates. Hence, the use of pretreatment for catalysis of lignocellulose substrates is beneficial for the production of cost-efficient and eco-friendly process. In this review, we discussed different pretreatment technologies of hydrolysis and their restrictions. The review has shown that different pretreatments have varying effects on lignin, cellulose, and hemicellulose degradation and biogas yield of different substrate and the choice of pretreatment technique will devolve on the intending final products of the process.

scholarly journals The impact of mechanical pretreatment on biogas production from waste materials of the chemical and brewing industries

2020 ◽  
pp. 1-12
Author(s):  
Katarzyna Bernat ◽  
Magdalena Zaborowska ◽  
Katarzyna Goryszewska
Keyword(s):  
Biogas Production ◽  
Waste Materials ◽  
Organic Load ◽  
Brewing Industry ◽  
Biogas Yield ◽  
Mechanical Pretreatment ◽  
Spent Grain ◽  
Willow Bark ◽  
The Impact ◽  
Kinetics Of

Respirometric tests, carried out in OxiTop system, were used to determine biogas production (BP) from two waste materials, willow bark residue (W) from the chemical industry and brewer’s spent grain (BSG) from the brewing industry. Moreover, the kinetics of BP and the loss of organic compounds (expressed as COD) were investigated. In this investigation, W and BSG were used both in their unchanged forms and after mechanical pretreatment (grinding to a diameter of 1 mm) (W_G and BSG_G). The initial organic load in the bioreactors was 4 kg OM/m3. The BP from W was 154.1 dm3/kg DM (166.6 dm3/kg OM), and from BSG, it was 536.9 dm3/kg DM (559.5 dm3/kg OM). This probably resulted from the fact that the content of lignin that was hard to biodegrade was higher in W than in BSG. Mechanical pretreatment increased BP from W_G to 186.7 dm3/kg DM (201.9 dm3/kg OM), and from BSG_G to 564.0 dm3/kg DM (588.7 dm3/kg OM). The net biogas yield from W and BSG increased by 17% (35 dm3/kg OM) and 5 % (29 dm3/kg OM), respectively. The kinetic coefficient of BP (kB) and the rate of BP (rB) of W were lower than those of BSG. Mechanical pretreatment increased the kB and rB of biogas production from both waste materials.

scholarly journals Chemical pre-treatments on oil palm empty fruit bunches: Impacts on characteristics and methane potential

2021 ◽  
Vol 924 (1) ◽  
pp. 012071
Author(s):  
N A Rohma ◽  
S Suhartini ◽  
I Nurika
Keyword(s):  
Lignocellulosic Biomass ◽  
Oil Palm ◽  
Biogas Production ◽  
Lignin Content ◽  
Test System ◽  
Biochemical Methane Potential ◽  
Empty Fruit Bunches ◽  
Methane Potential ◽  
Pre Treatment ◽  
Bmp Test

Abstract Production of biogas from lignocellulosic biomass by anaerobic digestion (AD) has attracted much interest. Oil palm empty fruit bunches (OPEFB), one of lignocellulosic biomass, is highly abundant in Indonesia and has potential as feedstock for bioenergy production such as biogas or methane. Yet, pre-treatments are needed to improve biogas production due to its complex crystalline structures. Chemical pre-treatments with acid or alkaline solution were reported to increase cellulose or highly reduce the lignin content of OPEFB. This study aimed to evaluate the effect of acid and alkaline pre-treatments on the characteristics of OPEFB and methane potential. The acid pre-treatment experimental design was used factor of H2SO4 concentration (1, 1.3, and 1.6 (%v/v)) and NaOH concentration (1.8, 2.8, and 3.8 (%w/v)). Methane potential evaluation was carried out using the biochemical methane potential (BMP) test with the Automatic Methane Potential Test System (AMPTS) II under mesophilic condition (37°C), operated for 28 days. The results showed that both dilute acid and alkaline pre-treatment positively impact altering the characteristics of OPEFB, hence the specific methane potential. Alkaline pre-treatment with NaOH 3.8 (%w/v) gave the highest average SMP value of 0.161 ± 0.005 m3 CH4/kgVSadded.

scholarly journals Pre-treatment of thickened waste activated sludge (TWAS) for enhanced biogas production via the application of a novel radial horn sonication technology

2017 ◽  
Vol 75 (9) ◽  
pp. 2179-2193 ◽  
Author(s):  
Sri Suhartini ◽  
Lynsey Melville ◽  
Tony Amato
Keyword(s):  
Activated Sludge ◽  
Biogas Production ◽  
Applied Pressure ◽  
Low Frequency ◽  
Waste Activated Sludge ◽  
Biochemical Methane Potential ◽  
Experimental Conditions ◽  
Working Volume ◽  
Methane Potential ◽  
Pre Treatment

The efficacy of sonication as a pre-treatment to anaerobic digestion (AD) was assessed using thickened waste activated sludge (TWAS). Efficiency was measured in relation to solubilisation, dewaterability, and AD performance. Eighteen experimental conditions were evaluated at low frequency (20 kHz), duration (2–10 s), amplitude (∼8–12 μm) and applied pressure (0.5–3.0 barg), using a sonix™ patented titanium sonoprobe capable of delivering an instantaneous power of ∼6 kW provided by Doosan Enpure Ltd (DEL). An optimised experimental protocol was used as a pre-treatment for biochemical methane potential (BMP) testing and semi-continuous trials. Four digesters, with a 2-L working volume were operated mesophilically (37 ± 0.5 °C) over 22 days. The results showed that the sonix™ technology delivers effective sonication at very short retention times compared to conventional system. Results demonstrate that the technology effectively disrupts the floc structures and filaments within the TWAS, causing an increase in solubilisation and fine readily digestible material. Both BMP tests and semi-continuous trials demonstrated that sonicated TWAS gave higher biodegradability and methane potential compared to untreated TWAS. Partial-stream sonication (30:70 sonicated to untreated TWAS) resulted in a proportionate increase in biogas production illustrating the benefits of full-stream sonication.

Sign in / Sign up

Export Citation Format

Share Document