scholarly journals Effect of provenances on wood properties of Balfourodendron riedelianum

2020 ◽  
Vol 26 (1) ◽  
Author(s):  
Amanda Aparecida Vianna Assad ◽  
Adriano Wagner Ballarin ◽  
Miguel Luiz Menezes Freitas ◽  
Eduardo Luiz Longui

Wood is comparatively more conservative than other parts of trees, such as leaves, which present greater phenotypic plasticity. We studied the effect of seed origin on annual increment, physical-mechanical properties and anatomical characteristics of Balfourodendron riedelianum wood in a homogeneous plantation (Luiz Antônio Experimental Station (LAES)) from three natural provenances (Gália and Bauru in São Paulo State and Alvorada do Sul in Paraná State, Brazil). Because genotypic information is a determinant of wood formation, trees were expected to develop wood structure based on their provenances. Our results demostrate that variations in volume, properties and wood anatomy were influenced by provenance. Alvorada do Sul trees showed lower growth in volume and higher strength and homogeneity, compared to Gália and Bauru. Typical radial pattern was not observed for most characteristics, except modulus of elasticity and fiber length in Gália and compression parallel to the grain in Bauru that increased towards the bark. Based on the latter characteristc, B. riedelianum wood in a homogeneous planting has class C40 mechanical strength, as indicated for use in medium-sized structures, light civil construction and the manufacture of furniture.

2017 ◽  
Vol 24 (0) ◽  
Author(s):  
Eduardo Luiz Longui ◽  
Gabriela Trindade Pires ◽  
Miguel Luiz Menezes Freitas ◽  
Diego Romeiro ◽  
Sandra Monteiro Borges Florsheim ◽  
...  

ABSTRACT We hypothesized that Myracrodruon urundeuva trees of two provenances with different genotypes would present variations influenced by their origin terms of anatomy and specific gravity when planted in an environment different from their seed origin, but under the same environmental conditions. We investigated radial variation in 12 trees. The observation that only vessel frequency and fiber length showed the same pattern of radial variation in the two provenances indicate that radial variation in M. urundeuva seems to depend on the origin of the seeds, that is, a genetic factor, rather than on the influence of climate and soil, which repreent environmental factors. We noticed marked differences in all features when comparing the same growth rings in each provenance, a result that reinforces the genetic influence on wood formation. We conclude that the studied plants maintain their wood structure as a result of genetic information, as selected by climatic conditions of seed original area, and possibly due to the highly conservative wood anatomy.


1970 ◽  
Vol 11 (1) ◽  
Author(s):  
Mohan P. Devkota ◽  
Gerhard Glatzel

Effects of infection by the mistletoe Scurrula elata (Edgew.) Danser, on wood properties of its common host Rhododendron arboreum Sm., were studied in the Annapurna Conservation Area of Central Nepal Himalaya. Heavy infection by mistletoes invariably causes decline of the host. Infested branches show inhibition of growth, defoliation and eventual death of branch parts distal to the site of infection. Anatomical properties of wood were compared in samples of branches proximal to the infection and in uninfected branches. The hypothesis that infection induces changes in basic wood anatomy could not be proven. Vessel density, vessel area, percentage lumen area and mean vessel diameter of the wood of infested and uninfected branches did not show any significant differences. The studied anatomical parameters were not correlated to the diameter of the host branch. These results show that infection by S. elata did not cause any changes in basic wood anatomy of its host R. arboreum. It appears that the studied anatomical parameters of Rhododendron wood are fairly stable and are not changed by stress due to infection by mistletoes. The damage to the host distal to the infected area most likely results from an insufficiency of total conductive area to supply both mistletoe and host. Unfortunately we could not determine annual conductive area increment, because R arboreum does not develop usable annual tree rings in the climate of the study area. Key words: Himalayas, mistletoe. Rhododendron arboreum, Scurrula elata, water stress, wood anatomy. Ecoprint Vol.11(1) 2004.


IAWA Journal ◽  
2015 ◽  
Vol 36 (2) ◽  
pp. 138-151 ◽  
Author(s):  
Luíza Teixeira-Costa ◽  
Gregório Ceccantini

Parasitic plants are capable of causing a variety of effects to their hosts, including alterations in the process of wood formation. However, the majority of studies dealing with parasitic plant anatomy have focused on the host–parasite interface and the direct action of the haustorium, which is the organ responsible for attaching the parasite to the host. Considering this gap, we studied the anatomical and functional effects caused by a mistletoe species, Phoradendron crassifolium (Santalaceae), on the wood anatomy of the host tree Tapirira guianensis (Anacardiaceae). Both parasitized and non-parasitized branches were collected from host trees. Traditional wood anatomy procedures were employed, along with functionality experiments using the ascent of safranin solution through the xylem. Prior to the analysis, all sampled branches were divided in “upstream” and “downstream” portions, considering the direction of xylem sap flow inside the plant body. This design was chosen in order to avoid biased results derived from normal ontogeny-related wood anatomical and functional changes. Our results showed that infested wood expressed a higher density of embolized vessels, narrower vessel lumen diameter, higher vessel density, taller and wider rays, and fibers with thinner cell walls. All these responses were most conspicuous in the downstream sections of the parasitized branches. We propose that the wood anatomical and functional alterations were induced by the combination of water stress caused by water use by the parasite and consequent low turgor in differentiating cambial derivates; by unbalanced auxin/cytokinin concentrations originating at the infestation region due to phloem disruptions caused by the parasite’s penetration and action; and by higher than usual ethylene levels. Further analysis of hydraulic conductivity and hormonal changes in host branches are necessary to test this hypothesis.


Author(s):  
Maritza L. Vaca-Cardenas ◽  
M. Oleas ◽  
Mónica Elva Vaca-Cárdenas ◽  
A. Velasco

The alpaca is one of the four South American camelids that mainly inhabit the inter-Andean zone of Ecuador. Alpaca fiber is characterized by being a natural, soft and resistant fiber, of which, the fleece is the most valued part. The objective of this research was to evaluate the quality parameters of alpaca fiber in terms of physical-mechanical properties. The research was carried out in the Tunishi Experimental Station, ESPOCH. A descriptive statistic of mean, minimum and maximum range, and separation of means per student was applied. The alpaca with characteristics of Huacaya breed was selected and the shearing was carried out manually to obtain the fleece. Later, the performance of the fleece was evaluated, which was 85.71%. Two categories of fiber were selected: fine and thick. Sixty samples were taken for analysis by stretched and unstretched fiber length. The measurements of unstretched fiber length in cm for the thin and thick fiber were 12.50 cm and 13.52 cm respectively, presenting significant differences (p≤0.05). The measurements of the stretched fiber length in cm were 17.29 cm for fine fiber and 17.27 cm for thick fiber, presenting no significant differences (p≥0.05). The resistance of thread and fabric for fine fiber was 590 N/cm2, and for thick fiber was 2835.5 N/cm2, presenting highly significant differences (p≤0.01). Regarding the percentage of yarn elongation, the values obtained were 19% for fine fiber and 12% for thick fiber, observing highly significant differences (p≤0.01). The thick fiber fabric had a better resistance (2.3 BAR) than the fine fiber fabric (1.7 BAR), with a time of 2.34 s and 1.88 s respectively. The classification of the fiber by its softness did not present significant differences. Finally, regarding the sensory classification, it was established as a soft fiber with 91%. Keywords: alpaca, fleece, fine fiber, thick fiber, fiber properties. Resumen La alpaca es uno de los cuatro camélidos sudamericanos que principalmente habitan en la zona interandina del Ecuador. La fibra de alpaca se caracteriza por ser una fibra natural, suave y resistente; de la cual, el vellón es la parte de la fibra del animal más valorada. El objetivo de esta investigación fue evaluar los parámetros de calidad de fibra de alpaca en cuanto a las propiedades físico - mecánicas. La investigación se la realizó en la Estación Experimental TUNSHI - ESPOCH. Se aplicó una estadística descriptiva de media, rango mínimo y máximo y separación de medias por t estudent. Se seleccionó a la alpaca con características de la raza Huacaya y se realizó la esquila por el método manual para la obtención del vellón. Posteriormente, se evaluó el rendimiento del vellón el cual fue de 85,71%, se seleccionaron dos categorías de fibra fina y gruesa. Sesenta muestras fueron tomadas para su análisis: longitud de mecha estirada y sin estirar. La media de longitud de fibra sin estirar en cm para la fina y gruesa fueron de 12,50 y 13,52 correspondientemente, presentando diferencias significativas (p≤0,05), La media de la longitud en cm de fibra estirada determinó que la fibra fina presentó una media de 17,29 y la fibra gruesa de 17,27 cm, sin presentar diferencias significativas (p≥0,05). La resistencia del hilo y tejido para la fibra fina fue de 590 N/cm2 y para la gruesa fue de 2835,5 N/cm2, presentando diferencias altamente significativas (p≤0,01). Finalmente, en cuanto al porcentaje de elongación de hilo, presentó un 19% para fibra fina y un 12% para gruesa, observándose también diferencias altamente significativas (p≤0,01). El tejido de la fibra gruesa tuvo mejor resistencia (2,3 BAR) que el de la fibra fina (1,7 BAR), con un tiempo de 2,34 s y 1,88 s respectivamente. La clasificación de la fibra por su suavidad, no presentó diferencias significativas. En cuanto a la clasificación sensorial se la ubico como una fibra suave con el 91%. Palabras clave: alpaca, vellón, fibra fina, fibra gruesa, propiedades de la fibra.


1995 ◽  
Vol 71 (5) ◽  
pp. 639-646 ◽  
Author(s):  
Y. H. Chui ◽  
Glenda MacKinnon-Peters

The rapid growth performance of exotic larch such as Japanese larch (Larix leptolepis (Sieb. et Zucc) Gord.) and European larch (Larix decidua Mill.) has attracted the attention of the forestry sector in eastern Canada and north-eastern United States for lumber and pulp production. While growth performance of these species in North America has been well documented, little is known with regards to their wood properties. The objective of this study was to evaluate the primary lumber grade yields, mechanical properties, fiber length, specific gravity and cold-water soluble extractives of larch from plantations in Maine, Nova Scotia, New Brunswick and Prince Edward Island. Samples were obtained from a Japanese (age 31), three European (age 17, 34 and 63) and one Japanese × European hybrid (age 22-27) larch stands. It was found that the structural grade yields of these species were relatively low because of the influence of knots. The mechanical properties (modulus of rupture and modulus of elasticity) of the mature European larch appeared to be comparable with published data for some native softwood species. Fiber length, specific gravity and cold-water soluble extractive content of all samples were similar to those found for other softwood species which are used for pulp production. Fiber length of the juvenile wood of European larch was significantly shorter than that of mature wood. Extractive content was highest in newly formed heartwood. Contrary to common belief, extractive content in young trees may not be low. Key words: Japanese larch (Larix leptolepis Gord.), European larch (Larix decidua Mill.), European × Japanese hybrid (Larix eurolepis), Wood properties, Lumber yields


2021 ◽  
Vol 914 (1) ◽  
pp. 012071
Author(s):  
R G H Rahmanto ◽  
R Damayanti ◽  
D A Agustiningrum ◽  
C Oktapiani ◽  
E R Satiti ◽  
...  

Abstract Indonesia is a mega-biodiversity country that grows about 4000 timber producer tree species in tropical rain forest. The comprehensive information of wood properties and quality is important in managing the natural resources sustainably. However, stem in basic properties studies of wood from the natural forest is limited because of some difficulties in harvesting until the transportation process. Hence, study the wood branches becomes a solution, as sometimes wood core samples are not adequate. The question was whether the branch properties could represent the main stem properties? Wood anatomy is an important wood property that can predict the other properties, for instance, the physical and mechanical properties, that determine the effective use of this material. This paper aims to present the comparison of wood anatomical properties of branches and main stem of seven commercial wood species. Quantitative and qualitative anatomical structures were investigated according to the International Association of Wood Anatomist (IAWA) Committee. Result shows that the quantitative wood anatomy of four samples (Mimba, Leda, Jabon, and Bintangur) was statistically different, while only one parameter in Tusam, Mindi, and Khaya was different. Accordingly, it can be concluded that studying the wood properties could be carried out using branch effectively.


2016 ◽  
Vol 13 (19) ◽  
pp. 5499-5510 ◽  
Author(s):  
Gonzalo Pérez-de-Lis ◽  
Ignacio García-González ◽  
Vicente Rozas ◽  
José Miguel Olano

Abstract. Non-structural carbohydrates (NSC) play a central role in the construction and maintenance of a tree's vascular system, but feedbacks between the NSC status of trees and wood formation are not fully understood. We aimed to evaluate multiple dependencies among wood anatomy, winter NSC, and phenology for coexisting temperate (Quercus robur) and sub-Mediterranean (Q. pyrenaica) oaks along a water-availability gradient in the NW Iberian Peninsula. Sapwood NSC concentrations were quantified at three sites in December 2012 (N =  240). Leaf phenology and wood anatomy were surveyed in 2013. Structural equation modelling was used to analyse the interplay among hydraulic diameter (Dh), winter NSC, budburst date, and earlywood vessel production (EVP), while the effect of Dh and EVP on latewood width was assessed by using a mixed-effects model. NSC and wood production increased under drier conditions for both species. Q. robur showed a narrower Dh and lower soluble sugar (SS) concentration (3.88–5.08 % dry matter) than Q. pyrenaica (4.06–5.57 % dry matter), but Q. robur exhibited larger EVP and wider latewood (1403 µm) than Q. pyrenaica (667 µm). Stem diameter and Dh had a positive effect on SS concentrations, which were related to an earlier leaf flushing in both species. Sapwood sugar content appeared to limit EVP exclusively in Q. pyrenaica. In turn, Dh and EVP were found to be key predictors of latewood growth. Our results confirm that sapwood SS concentrations are involved in modulating growth resumption and xylem production in spring. Q. pyrenaica exhibited a tighter control of carbohydrate allocation to wood formation than Q. robur, which would play a role in protecting against environmental stress in the sub-Mediterranean area.


IAWA Journal ◽  
1991 ◽  
Vol 12 (3) ◽  
pp. 263-274 ◽  
Author(s):  
A. E. Akachuku

Leaning red pine (Pinus resinosa) trees at Harvard Forest in Petersham, Massachusetts, U.S.A., were sampled for wood growth studies 50 years after they were displaced by a hurricane. Before the hurricane incursion, ring width varied among trees and from year to year but not among radiL After the hurricane, between-tree variation in ring width was again significant but it was not appreciably due to angle of displacement (AOD) of the bole. Wood growth distribution along the bole in the leaning trees was complex. Between- radius variation in ring width was significant in the leaning boles; ring width was largest on the lower side. On the average ring width decreased as tree age increased but the variation was much less on the upper than on the lower side. Ring area tended to decrease with increase in age but the relationship was strongest in the least displaced bole and vice versa. Asymmetrie growth ratio increased with AOD of a bole and varied with year of wood formation but was not related to cambium age. Graphs of height above the ground on percentage pith eccentricity exhibited a sinuous shape like that of the trees. Cumulative growth and mean annual increment of height and volume increased with tree age. Current annual increment of height and volurne decreased for 9 and 5 years after the hurricane and after the 64th and 69th year of the tree, respectively. Form factor increased after pruning but decreased later with age. Precipitation was not closely related to ring width in the leaning boles.


2000 ◽  
Vol 30 (5) ◽  
pp. 761-768 ◽  
Author(s):  
R Spicer ◽  
B L Gartner ◽  
R L Darbyshire

Stem sinuosity is thought to negatively impact wood quality, but no studies have characterized its vertical and radial effects on wood properties. Here we study wood quality along the entire stem in 25-year-old plantation-grown Douglas-fir (Pseudotsuga menziesii var. menziesii (Mirb.) Franco) trees (32 trees total) that had been scored for sinuosity at age 12. We also study compression wood formation in the radial direction for one internode that had been scored for sinuosity at age 12 and subsequently produced 13 more annual rings. Trees with highly sinuous leaders at age 12 were more likely to be sinuous in other years, and developed more slope of grain defect (approximately 15% log volume) than less sinuous trees, but did not differ in the size of the pith-containing core. Leaders originally scored as highly sinuous developed more compression wood than control trees but only near the pith. Internode length did not differ among sinuosity classes. The size of the pith deviations (radial distance from centreline) remained constant up the stem despite a decline in internode length. However, the frequency of pith deviations was highest at 10-15 years, when internode length reached a peak. The relationship between temporal patterns of growth rate, sinuosity, and tree biomechanics deserves further attention.


Author(s):  
Mingyang Quan ◽  
Xin Liu ◽  
Qingzhang Du ◽  
Liang Xiao ◽  
Wenjie Lu ◽  
...  

Abstract Photosynthesis and wood formation underlie the ability of trees to provide renewable resources and perform ecosystem services; however, the genetic basis and regulatory pathways coordinating these two linked processes remain unclear. Here, we used a systems genetics strategy, integrating genome-wide association study, transcriptomic analyses, and transgenic experiments, to investigate the genetic architecture of photosynthesis and wood properties among 435 unrelated individuals of Populus tomentosa and unravel the coordinated regulatory networks causative of two trait categories. We totally detected 222 significant single-nucleotide polymorphisms, annotated to 177 candidate genes, for 10 traits of photosynthesis and wood properties. Epistasis uncovered 74 epistatic interactions for phenotypes. Strikingly, we deciphered the coordinated regulation patterns of pleiotropic genes underlying phenotypic variations for two trait categories. Furthermore, expression quantitative trait nucleotide mapping and coexpression analysis were integrated to unravel the potential transcriptional regulatory networks of candidate genes coordinating photosynthesis and wood properties. Finally, we heterologously expressed two pleiotropic genes, PtoMYB62 and PtoMYB80, in Arabidopsis thaliana, and demonstrated that they coordinate regulatory networks balancing photosynthesis and stem secondary cell wall components, respectively. Our study provides insight into the regulatory mechanisms coordinating photosynthesis and wood formation in poplar, which will accelerate the genetic breeding in trees via molecular design.


Sign in / Sign up

Export Citation Format

Share Document