scholarly journals EFFECT OF PYROLYSIS TEMPERATURES ON COMPOSITION AND ELECTRICAL CONDUCTIVITY OF CARBOSIL PREPARED FROM RICE HUSK

2012 ◽  
Vol 12 (2) ◽  
pp. 119-125 ◽  
Author(s):  
Wasinton Simanjuntak ◽  
Simon Sembiring ◽  
Kerista Sebayang
Keyword(s):  
Electrical Conductivity ◽  
Functional Groups ◽  
Rice Husk ◽  
Pyrolysis Temperature ◽  
X Ray Diffraction ◽  
Compression Pressure ◽  
X Ray ◽  
Different Temperatures ◽  
Potential Use ◽  
Scanning Electron

The objective of this study was to evaluate the effect of pyrolysis temperatures on composition and electrical conductivity of carbosil produced from rice husk, by conducting pyrolysis experiments at three different temperatures of 200; 400; and 700 °C. The structure of the samples was characterized using Fourier Transform Infrared (FTIR) Spectroscopy and X-Ray Diffraction (XRD). The microstructure and elemental composition were characterized using Scanning Electron Microscopy/Energy Dispersive Spectroscopy (SEM/EDS), and the electrical conductivity was measured using four probe method. The FTIR analyses revealed the existence of Si-O-Si and Si-OH functional groups, but no functional groups associated with carbon, confirming the formation of carbosil. This formation of carbosil is also supported by the results of EDS analyses which show the presence of only three elements of C, O, and Si, respectively. The XRD results indicate that the carbosils are amorphous, suggesting that no transformation of carbon and silica into crystalline phase to the limit of the temperatures applied. The carbosil formation decreased with increasing of pyrolysis temperature. The microstructure of the carbosils indicates that the higher the temperature, the smaller the grain size of the samples. The values of electrical conductivity of the samples are in the range of 1.13 x 10-3 to 6.81 x 10-3/(Ω.m) with the application of 10 tones compression pressure, but the conductivities of the sample prepared at 200 °C were found to increase with increased compression pressure to six fold from 6.81 x 10-3 to 41.94 x 10-3/(Ω.m) by increasing compression pressure to 80 tones. Based on these conductivity values, the samples are considered as semiconductor, suggesting the potential use of the carbosil in semiconductor devices.

scholarly journals Impact of Pyrolysis Temperature on the Properties of Eucalyptus Wood-Derived Biochar

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5841
Author(s):  
Bruno Caio Chaves Fernandes ◽  
Kassio Ferreira Mendes ◽  
Ananias Francisco Dias Júnior ◽  
Vinícius Patrício da Silva Caldeira ◽  
Taliane Maria da Silva Teófilo ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electrical Conductivity ◽  
Scanning Electron Microscopy ◽  
Pyrolysis Temperature ◽  
Volatile Matter ◽  
Matter Content ◽  
X Ray Diffraction ◽  
X Ray ◽  
Eucalyptus Wood ◽  
Scanning Electron

Pyrolysis conditions directly influence biochar properties and, consequently, influence the potential use of biochar. In this study, we evaluated the effects of different pyrolysis temperatures (450, 550, 650, 750, 850, and 950 °C) on the hydrogen potential, electrical conductivity, ash content, yield, volatile matter content, elemental analysis, Fourier-transform infrared spectroscopy results, X-ray diffraction results, scanning electron microscopy results, specific surface area, and micropore volume of eucalyptus wood-derived biochar. The degree of linear association between pyrolysis temperatures and biochar properties was examined using the Pearson correlation coefficient. The results showed a positive correlation of the pyrolysis temperature with the hydrogen potential value, electrical conductivity, and elemental carbon. There was a negative correlation of the pyrolysis temperature with the yield, volatile matter content, elemental oxygen, elemental hydrogen, surface area, aromaticity, hydrophilicity, and polarity indexes. The Fourier-transform infrared spectroscopy data indicated an increase in aromaticity and a decrease in the polarity of high-temperature biochar. The increased pyrolysis temperature caused the loss of cellulose and crystalline mineral components, as indicated by X-ray diffraction analysis and scanning electron microscopy images. These results indicated that changing the pyrolysis temperature enables the production of biochar from the same raw material with a wide range of physicochemical properties, which allows its use in various types of agricultural and environmental activities.

scholarly journals Effect of sintering temperature on electrical and microstructure properties of hot pressed Cu-TiC composites

2014 ◽  
Vol 46 (1) ◽  
pp. 15-21 ◽  
Author(s):  
S. Islak ◽  
D. Kır ◽  
S. Buytoz
Keyword(s):  
Electrical Conductivity ◽  
Phase Composition ◽  
Sintering Temperature ◽  
Applied Pressure ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
Pressing Method ◽  
X Ray ◽  
Different Temperatures ◽  
Scanning Electron

In this study, Cu-TiC composites were successfully produced using hot pressing method. Cu-TiC powder mixtures were hot-pressed for 4 min at 600, 700 and 800?C under an applied pressure of 50 MPa. Phase composition and microstructure of the composites hot pressed at different temperatures were characterized by X-ray diffraction, scanning electron microscope, and optic microscope techniques. Microstructure studies revealed that TiC particles were distributed uniformly in the Cu matrix. With the increasing sintering temperature, hardness of composites changed between 64.5 HV0.1 and 85.2 HV0.1. The highest electrical conductivity for Cu-10 wt.% TiC composites was obtained for the sintering temperature of 800?C, with approximately 68.1% IACS.

scholarly journals Pengaruh Suhu Kalsinasi terhadap Karakteristik Komposit Forsterit-Karbon Tersintesis dalam Medium Gas Argon

2020 ◽  
Vol 16 (2) ◽  
pp. 12
Author(s):  
Solihudin Solihudin ◽  
Haryono Haryono ◽  
Atiek Rostika Noviyanti ◽  
Muhammad Rizky Ridwansyah
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Rice Husk ◽  
Energy Dispersive Spectroscopy ◽  
Carbon Composite ◽  
X Ray Diffraction ◽  
Argon Gas ◽  
X Ray ◽  
Scanning Electron

<p>Komposit forsterit-karbon merupakan salah satu material modifikasi dari forsterit yang berpotensi memiliki sifat isolator panas baik. Karbon dalam komposit dapat mengisi cacat titik pada kristal forsterit. Arang sekam padi (residu gasifikasi) mengandung SiO2 amorf dan karbon yang tinggi. Penelitian ini bertujuan menentukan pengaruh suhu kalsinasi dalam medium gas inert (dengan pengaliran gas argon) terhadap karakteristik komposit forsterit-karbon dari arang sekam padi dan magnesium karbonat. Metode penelitian meliputi preparasi arang sekam padi hasil gasifikasi, dan sintesis forsterit-karbon. Proses sintesis komposit forsterit karbon dilakukan dengan cara mencampurkan arang sekam padi dengan kalium karbonat pada rasio mol magmesium terhadap silikon sebesar 2 : 1 kemudian dikalsinasi dengan suhu divariasikan (700, 800, 900, dan 1000 oC). Selanjutnya sampel hasil sintesis dikarakterisasi dengan Fourier-transform infrared (FTIR), X-ray diffraction (XRD), dan scanning electron microscope-energy dispersive spectroscopy (SEM-EDS). Hasil karakterisasi dengan FTIR dan XRD diperoleh kesimpulan bahwa forsterit mulai terbentuk pada suhu kalisiasi 800 oC dan sempurna pada suhu 1000 oC, karenanya komposit yang terbentuk pada 1000 oC dimungkinkan sebagai forsterit-karbon, di mana unsur-unsur yang terkandung ditunjukkan oleh SEM-EDS.</p><p> </p><p><strong>The Effect of Calcination Temperature on the Characteristics of Forsterite-Carbon Composites Synthesized in Argon Gas Medium</strong>. Forsterite-carbon composite is one of the material modifications of forsterite, which potentially has a good heat insulation property. Carbon in composites can fill point defects in forsterite crystals. Rice husk charcoal, as gasification residues, contains high amorphous SiO2 and carbon. This study aims to determine the effect of temperature on the calcination of a mixture of rice husk charcoal and magnesium carbonate under an inert gas (argon gas) on the characteristics of the forsterite-carbon composite produced. The experimental research performed includes the preparation of gasified rice husk charcoal and the synthesis of the carbon-forsterite composite. The synthesis process of the carbon-forsterite composites was carried out by mixing rice husk charcoal with potassium carbonate at a mole ratio of magnesium to silicon of 2 : 1. The mixture was then calcined with varying temperatures (700, 800, 900, and 1000 °C). Furthermore, the synthesized sample was characterized by Fourier-transform infrared (FTIR), X-ray diffraction (XRD), and scanning electron microscope-energy dispersive spectroscopy (SEM-EDS). The FTIR and XRD analysis show that the forsterites began to form at a calcination temperature of 800 °C and perfectly formed at a temperature of 1000 °C; therefore, the composite formed at 1000 °C is possible as forsterite-carbon, in which the contained elements were indicated by SEM-EDS.</p>

Microstructure and Properties of Nanosemicrystalline Si3N4 Ceramics with Doped Sintering Additives: Part II. Phase Transformation and Microstructural Control

1998 ◽  
Vol 13 (9) ◽  
pp. 2588-2596 ◽  
Author(s):  
K. H. Ryu ◽  
J-M. Yang
Keyword(s):  
Electron Microscopy ◽  
Pressureless Sintering ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sintering Additives ◽  
Different Temperatures ◽  
Si3n4 Ceramics ◽  
Scanning Electron ◽  
Microstructural Control

The low temperature pressureless sintering of a nanosized Si3N4 powder with doped sintering additives was investigated. The microstructural evolution during sintering at different temperatures was analyzed using x-ray diffraction and scanning electron microscopy. The effect of using nanosized Si3N4 powder as a catalyst to accelerate the α→β–Si3N4 transformation of a commercial Si3N4 powder with larger particle sizes was also investigated. Finally, two stage sintering was used to study the feasibility of controlling the microstructure and the mechanical properties of the nanosized silicon nitride.

Microstructural and Corrosion Studies by Immersion in 3.5% NaCl Solution on Aged Mg-9Al-1Zn-XCa Alloy

2019 ◽  
Vol 969 ◽  
pp. 93-97
Author(s):  
S. Manivannan ◽  
B. Narenthiran ◽  
A. Sivanantham ◽  
S.P. Kumaresh Babu
Keyword(s):  
Corrosion Behaviour ◽  
Nacl Solution ◽  
X Ray Diffraction ◽  
Corrosion Attack ◽  
X Ray ◽  
Α Phase ◽  
Corrosion Studies ◽  
Different Temperatures ◽  
Xrd Techniques ◽  
Scanning Electron

The experimatal alloys were aged at different temperatures of 180°C, 200°C, 220°C, and 240º C with calcium addition levels of (X=0.5, 1, 1.5, 2%) on Mg-6Al-1Zn-XCa alloy were investigated in 3.5% NaCl solution. All the experimatal alloys were immersed in 3.5% NaCl solutions and the resulted surface were analyzed to study the corrosion behaviour and its surface topography by optical microscopy (OM), scanning electron microscopy (SEM), energy dispersed spectroscopy (EDS) and X-ray diffraction (XRD) techniques. The result shows that corrosion attack occurred predominantly on ß phase and α phase exhibit relatively minor corrosion. In addition to that the increased aging temperature coarsens the intermetallic as well as α- Mg grains, which shows adverse effect to corrosion resistances and the best result were obtained at composition of 0.5wt.% Ca aged at 200°C.

Effect of Sintering Temperature on Silver-Copper Nanopaste as High Temperature Die Attach Material

2013 ◽  
Vol 795 ◽  
pp. 47-50 ◽  
Author(s):  
Kim Seah Tan ◽  
Kuan Yew Cheong
Keyword(s):  
Electrical Conductivity ◽  
High Temperature ◽  
Sintering Temperature ◽  
Grain Structure ◽  
Binder System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Silver Copper ◽  
Die Attach ◽  
Scanning Electron

A novel stencil-printable silver-copper (Ag-Cu) nanopaste that serves as an alternative high temperature die attach material was introduced in this study. The nanopaste was made by mixing 50 nm-sized of Ag and Cu particles with an organic binder system. Sintering temperatures, up to 450°C, were used to sinter nanopaste in air and its post sintered properties were investigated. The viscosity of nanopaste was 350,000 cps and it demonstrated a shear thinning behavior. Scanning electron microscope revealed the change of grain structure with the change in the sintering temperature. Formations of Ag97Cu3 and Ag1Cu99 compounds after sintering were confirmed with X-ray diffraction; and the electrical conductivity of the sintered nanopaste was increased with the increase of the sintering temperature. The study concluded 380°C was the optimum sintering temperature to form a well sintered nanopaste.

Characterization of LSCF-Based Composite and LSCF as Cathodes for Intermediate Temperature SOFCs

2012 ◽  
Vol 727-728 ◽  
pp. 657-662
Author(s):  
Reinaldo Azevedo Vargas ◽  
Everton Bonturim ◽  
Marco Andreoli ◽  
Rubens Chiba ◽  
Emília Satoshi Miyamaru Seo
Keyword(s):  
Solid Oxide Fuel Cells ◽  
Solid Oxide ◽  
Intermediate Temperature ◽  
Oxide Fuel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Spraying ◽  
Potential Use ◽  
Scanning Electron

The (La0.60Sr0.40)(Co0.20Fe0.80)O3-δ - LSCF, (Ce0.90Gd0.10)O1.95 - CGO composites and LSCF were deposited by wet powder spraying deposition method for the purpose of investigating their potential use in Intermediate Temperature Solid Oxide Fuel Cells. The interlayers are necessary between CGO electrolytes and LSCF cathodes in order to improve the performance of these materials. LSCF particles synthesized by citrate technique were calcined at 900 °C for 4 h and, their LSCF-CGO composites and LSCF suspensions deposited on CGO substrate and, sintered in 1100 °C for 1 h, were formed pseudo-perovskite. The ceramics materials were analyzed by X-ray diffraction (XRD) and chemical composition of different half-cells layers by scanning electron microscope with energy dispersive (SEM-EDS). The results are in agreement with the literature and indicate that route studied is adequate for crystal structures formation compatible with films the 35 µm thick total for study of conductivity between the cathode and the electrolyte.

scholarly journals Preparation of BaZrO3 powders by a spray-drying process

2003 ◽  
Vol 18 (6) ◽  
pp. 1325-1332 ◽  
Author(s):  
B. Robertz ◽  
F. Boschini ◽  
A. Rulmont ◽  
R. Cloots ◽  
I. Vandriessche ◽  
...  
Keyword(s):  
Spray Drying ◽  
Precursor Solution ◽  
Barium Zirconate ◽  
Drying Process ◽  
X Ray Diffraction ◽  
High Quality ◽  
Corrosion Resistant ◽  
X Ray ◽  
Potential Use ◽  
Scanning Electron

The potential use of barium zirconate for the manufacture of corrosion-resistant substrates emphasizes the need for a simple, inexpensive, and easily scalable process to produce high-quality powders with well-controlled composition and properties. However, the classical solid-state preparation of barium zirconate leads to an inhomogeneous powder unsuitable for applications in highly corrosive environment. For this paper, the possibility to use the spray-drying technique for the preparation of BaZrO3 powders with a controlled size distribution and morphology was investigated. The influence of the nature and concentration of the precursor solution and the influence of the spray-drying step are discussed on the basis of x-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and dilatometric measurements.

Novel Hierarchical TiO2/C Nanocomposite with Enhanced Photocatalytic Performance

NANO ◽  
2015 ◽  
Vol 10 (05) ◽  
pp. 1550064 ◽  
Author(s):  
Yupeng Gao ◽  
Hao Chen ◽  
Aiguo Zhou ◽  
Zhengyang Li ◽  
Fanfan Liu ◽  
...  
Keyword(s):  
Photocatalytic Performance ◽  
Photocatalytic Property ◽  
Two Dimensional ◽  
X Ray Diffraction ◽  
Carbon Nanocomposites ◽  
Carbon Nanosheets ◽  
X Ray ◽  
The Hierarchical Structure ◽  
Different Temperatures ◽  
Scanning Electron

Hierarchical TiO 2/carbon nanocomposites were synthesized by oxidation of two-dimensional (2D) Ti 3 C 2 nanosheets at different temperatures. Crystal structures and morphologies of the obtained samples were characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD) and Raman spectroscopy. The results show that 2D Ti 3 C 2 nanosheets are partially oxidized to form a novel hierarchical nanostructure which is composed of carbon nanosheets and TiO 2 nanoparticles. With the calcination temperature increasing, the crystal structure of TiO 2 nanoparticles changes from anatase to rutile and the hierarchical structure was gradually destroyed. The photodegradation results reveal that the samples obtained at 200°C and 285°C show much better photocatalytic properties than P25. And meanwhile the photocatalytic property will become worse with the increase in calcinations temperature.

scholarly journals Synthesis and Catalase Mimic Activity of MnO2 Nano Powder Prepared by Hydrothermal Process

2019 ◽  
Vol 27 (2) ◽  
pp. 228-237 ◽  
Author(s):  
Rashed T. Rasheed ◽  
Sariya D. Al-Algawi ◽  
Rosul M. N.
Keyword(s):  
Crystal Structure ◽  
Electron Microscopy ◽  
Annealing Temperature ◽  
Hydrothermal Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Atomic Force ◽  
Different Temperatures ◽  
Scanning Electron

Manganese dioxide (MnO2) nanopowder has been synthesized by hydrothermal method. MnO2 was annealed at different temperatures (250, 400, 550, 700˚C). The crystal structure and surface morphology of these nanostructures were characterized by X-ray diffraction (XRD), Atomic Force Microscope (AFM) and Scanning Electron Microscopy (SEM). The catalase mimic activity (catalytic activity) of MnO2 against hydrogen peroxide (H2O2) was studied by using the new method and found that 400˚C is the best annealing temperature.

Sign in / Sign up

Export Citation Format

Share Document