scholarly journals Justification of the Gravitational Seed Cleaning System Parameters

2020 ◽  
Vol 14 (4) ◽  
pp. 26-32
Author(s):  
V. G. Khamuev

The author researched the gravitational method of separating a grain heap, in which cleaning from large and small impurities was carried out without energy consumption, with the gravity material fl ow in vertical cleaning columns along fi xed zigzag separating combs.(Research purpose) To study the gravity column operation for cleaning selection seeds and substantiate its design parameters.(Materials and methods) A prototype gravity column was developed. The author experimentally determined: the combs teeth diameter; column throughput; the possibility of a more complete separation of the seed fraction from the basic material; completeness of large impurities separation. He compared the work of the gravity column and the fl at rocking sieve. He assessed the combs jamming by the cleaned culture seeds.(Results and discussion) The author noted that on wheat cleaning at a productivity of 45.6 kilogram per hour, the yield of the "waste" fraction was 0.5 percent, a loss of 0.07 percent, and at a productivity of 227.8 kilogram per hour – 0.98 and 0.35 percent, which corresponded to the initial requirements for the main technological operations for post-harvest processing of selection seeds.(Conclusions) It was found that a gravity column for separating selection wheat seeds small impurities separated particles with high effi ciency if they diff ered from each other in thickness of at least 0.3 millimeter with a gap between the comb bars of 2.0 millimeter and a bar cross-section diameter of 0.9 millimeter. It was determined that high productivity – up to 150 kilogram per hour – was possible with a column cross-section with sides of 60 and 70 millimeter. The author revealed practically the same quality of material separation when separating small impurities using both a sieve and a gravity column.

1975 ◽  
Vol 97 (4) ◽  
pp. 408-416 ◽  
Author(s):  
J. K. Hedrick ◽  
R. J. Ravera ◽  
J. R. Anderes

In this paper the ride quality of a vehicle traversing an elevated guideway is related directly to guideway construction tolerances and design parameters. Moreover, the construction tolerances are modeled in terms familiar to a guideway contractor. The tolerances modeled for an elevated, two-span semicontinuous, concrete guideway are: surface finish, camber deviations, pier survey errors, and pier settlement. The major design parameters relating to live-load deflection, stiffness (material and cross-section), and pier spacing are included. A general technique is presented for relating these tolerances to vehicle ride quality by means of a digital computer simulation. Various ride quality criteria are considered, including rms acceleration, acceleration spectral density, acceleration frequency decomposition, and a deterministic state space boundary. Numerical results are presented for a particular vehicle-guideway configuration and as such are valid only for the system considered. It is shown that for this system, equivalent ride quality can be maintained while adjusting the various construction tolerances. This trade-off capability allows the contractor to choose the least costly combination of tolerance parameters.


2016 ◽  
Vol 6 (2) ◽  
pp. 31-35 ◽  
Author(s):  
Arkadiy N. KIM ◽  
Ekaterina V. DAVYDOVA ◽  
Delyara I. POLYANSKAYA

Analysis of the technical state of the surface runoff drainage and cleaning system in Astrakhan was conducted, the analysis of indicators of the quality of surface wastewaters was conducted. Key controlled parameters defi ning the necessary cleaning effi ciency - suspended solids and oil. Variants of surface water treatment using local fi ltering materials are given.


2007 ◽  
Vol 339 ◽  
pp. 16-20 ◽  
Author(s):  
H. Hocheng ◽  
Chung Chen Tsao

Delamination is one of the most concern defects in drilling of composite material. Delamination depends on the factors such as feed rate, tool geometry and wear. The mechanics of drilling composite materials has been examined along with the quality of the hole and the effect of tool design parameters. The capacity of computerized tomography (CT) showing sample cross-section in a nondestructive way made it successful in measuring the drilling-induced delamination. In the experiment, the correlation between thrust force and the measured delamination extent in use of twist drill and core drill is illustrated and compared with the known ultrasonic C-scan. It is compared with the ultrasonic technique and is demonstrated a feasible and an effective tool for the evaluation of drilling-induced delamination.


2016 ◽  
Vol 3 (1) ◽  
pp. 55-60
Author(s):  
Yu. Lavrynenko ◽  
R. Vozhegova ◽  
O. Hozh

The purpose of the research is to identify effi cient microfertilizers and growth stimulants considering biologi- cal features of new corn hybrids of different FAO groups under irrigation conditions in the South of Ukraine and trace their impact on grain productivity of the plants. The methods of the research are the fi eld method – to study the interaction of the research object with experimental factors of the natural environment, to register the yield and evaluate the biometrical indices; the laboratory method – to measure soil moisture, grain moisture content and grain quality indices; the statistical method – to evaluate the reliability of the obtained results; the calculation methods – for economic and energetic assessment of the growing techniques used. The results of the research. The paper defi nes the impact of microfertilizers and growth stimulants on the yield and grain quality of the corn hybrids of different maturity groups and on the economic effi ciency of growing them. The conclusions of the research. Under irrigation conditions of the Southern Steppe of Ukraine it is recommended that the following hybrids should be grown in dark-chestnut soils: early maturity DN Pyvykha, medium-early Skadovskyi, medium maturity Kakhovskyi and medium-late Arabat, using the growth stimulants – treating the seeds with Sezam-Nano and fertilizing with Grainactive at the stage of 7–8 leaves.


2019 ◽  
Vol 1 (7) ◽  
pp. 10-13
Author(s):  
D. Yu. Ershov ◽  
I. N. Lukyanenko ◽  
E. E. Aman

The article shows the need to develop diagnostic methods for monitoring the quality of lubrication systems, which makes it possible to study the dynamic processes of contacting elements of the friction systems of instrument mechanisms, taking into account roughness parameters, the presence of local surface defects of elements and the bearing capacity of a lubricant. In the present article, a modern diagnostic model has been developed to control the quality of the processes of production and operation of friction systems of instrument assemblies. With the help of the developed model, it becomes possible to establish the relationship of diagnostic and design parameters of the mechanical system, as well as the appearance of possible local defects and lubricant state, which characterize the quality of friction systems used in many mechanical assemblies of the mechanisms of devices. The research results are shown in the form of nomograms to assess the defects of the elements of friction mechanisms of the mechanisms of the devices.


Agronomy ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 261
Author(s):  
María Teresa Ariza ◽  
Luis Miranda ◽  
José Antonio Gómez-Mora ◽  
Juan Jesús Medina ◽  
David Lozano ◽  
...  

Strawberry (Fragaria×ananassa Duch.) production requires the input of large amounts of water provided by irrigation during the entire production cycle. However, water availability is shrinking in many important strawberry cropping areas, such as Huelva (in Europe), compromising the environmental sustainability and economic viability of strawberry production. Besides technical approaches, water-saving strategies are necessary for improving strawberry water productivity such as the use of low water-consumptive cultivars with high productivity or cultivars allowing deficit irrigation (DI) strategies. A two-year field experiment was conducted to compare the physiological and agronomical response of six commercial strawberry cultivars (‘Sabrina’, ‘Fortuna’, ‘Splendor’, ‘Primoris’, ‘Rabida’ and ‘Rociera’) to six different water treatments ranging from 65% to 140% of estimated ‘Sabrina’ evapotranspiration (ETcSab; ~224–510 mm year−1). Cultivars differed substantially in yield and water consumption linked to their biomass partitioning into reproductive/ vegetative organs, determining different yield efficiency (YE). Their water needs (IN) conditioned their response to different water supplies, involving significant yield losses in DI treatments (<20% IN) but not decreasing fruit quality. The highly-consumptive and productive ‘Rabida’ and ‘Rociera’, reduced yields by DI (<40%) but were still profitable; the low-water-consumptive but still productive ‘Fortuna’, ‘Splendor’ and ‘Primoris’ represent significant water-savings (<20%) in strawberry cultivation.


2013 ◽  
Vol 791-793 ◽  
pp. 799-802
Author(s):  
Ya Ping Wang ◽  
H.R. Shi ◽  
L. Gao ◽  
Z. Wang ◽  
X.Y. Jia ◽  
...  

With the increasing of the aging of population all over the world, and With the inconvenience coming from diseases and damage, there will be more and more people using the wheelchair as a tool for transport. When it cant be short of the wheelchair in the daily life, the addition of the function will bring the elevation of the quality of life for the unfortunate. Staring with this purpose, the research designs a pickup with planetary bevel gear for the wheelchair. After determining the basic function of the wheelchair aids, the study determines the design parameters by using the knowledge of parametric design and completes the model for the system with Pro/E, on the other hand, it completes key components optimization analysis which is based on genetic algorithm optimization.


2013 ◽  
Vol 433-435 ◽  
pp. 2277-2281
Author(s):  
Quan Wei Wang ◽  
Ming Hui Wang ◽  
Dong Li ◽  
Dian Mao Wan ◽  
Rong Meng

By analyzing the relationship of the design parameters of NYD contact backstop, the cross-section curve of the wedge block has been discussed as Archimedes spiral, logarithm spiral and arc. Each curve is designed optimally using MATLAB optimization toolbox. The merits and drawbacks of each curve are discussed.


2011 ◽  
Vol 121-126 ◽  
pp. 1744-1748
Author(s):  
Xiang Yang Jin ◽  
Tie Feng Zhang ◽  
Li Li Zhao ◽  
He Teng Wang ◽  
Xiang Yi Guan

To determine the efficiency, load-bearing capacity and fatigue life of beveloid gears with intersecting axes, we design a mechanical gear test bed with closed power flow. To test the quality of its structure and predict its overall performance, we establish a three-dimensional solid model for various components based on the design parameters and adopt the technology of virtual prototyping simulation to conduct kinematics simulation on it. Then observe and verify the interactive kinematic situation of each component. Moreover, the finite element method is also utilized to carry out structural mechanics and dynamics analysis on some key components. The results indicate that the test bed can achieve the desired functionality, and the static and dynamic performance of some key components can also satisfy us.


Author(s):  
А.О. РЕНЗЯЕВ ◽  
О.П. РЕНЗЯЕВ ◽  
С.Н. КРАВЧЕНКО ◽  
Р.В. КРЮК

Исследованы прочностные и физико-механические свойства оболочки рапса с точки зрения ее разрушения и удаления. Установлено, что наиболее рациональным является двухстадийный способ обрушивания: 1-я стадия – на вальцовых мельницах, 2-я – на центробежной обрушивающей машине. Определены параметры центробежной обрушивающей машины для обеспечения минимальной необходимой линейной скорости 10,81 м/с: угол наклона отбойной пластины (90 ± 2)°, частота вращения барабана (2400 ± 150) об/мин. Установлено, что правильно подобранные условия и угол, под которым происходит удар, позволяют значительно снизить количество не до конца обрушенного семени и содержание расколотого ядра. При этом при свободном ударе об отбойную пластину под углом, отличным от 88–91°, или подаче недостаточно равномерного потока семян значительно увеличивается содержание необрушенных семян. На разрушение 1 кг семян необходимо затратить 58,45 Дж. Таким образом, по расчетным данным, для семян рапса диаметром 1,5 мм частота вращения барабана должна находиться в диапазоне от 2221 до 2565 об/мин при ударе семени под углом 90°. Диаметр семян рапса, выращиваемого в Сибирском регионе, составляет от 0,8 до 1,8 мм. Установлено, что подсушивание семян рапса в течение 30–40 с при температуре 100°С позволяет увеличить эффективность разрушения оболочки до полного ее отделения от ядра рапса. Представленные результаты позволяют повысить качество очистки семян рапса от оболочки и улучшить качественные характеристики получаемого масла, облегчить последующие технологические процессы получения пищевого масла, снизить затраты на рафинацию и дезодорацию на 2%. The strength and physico-mechanical properties of the shell of rapeseed in terms of its destruction and removal are investigated. It is established that the most rational is a two-stage method of seed hulling: the 1st stage – on roller mills, the 2nd – on a centrifugal hulling machine. The parameters of the centrifugal hulling machine to provide the minimum required linear speed of 10,81 m/s are defined: the angle of inclination of the turnback plate (90 ± 2)°, the rotational speed of drum (2400 ± 150) RPM. It is established that the correctly selected conditions and the angle at which the impact occurs, can significantly reduce the amount is not completely hulling seed and the substance of the split nucleus. At the same time, with a free impact on the turnback plate at an angle different from 88–91°, or the supply of an insufficiently uniform flow of seeds, the content is not completely hulling seed increases significantly. On hulling of 1 kg of seeds it is necessary to spend 58,45 J. Thus, according to the calculated data, for rape seeds with a diameter of 1,5 mm, the rotational speed of drum should be in the range from 2221 to 2565 RPM when the seed is struck at an angle of 90°. The diameter of rapeseed grown in the Siberian region ranges from 0,8 to 1,8 mm. It was found that drying of rapeseed for 30–40 s at a temperature of 100°C, can increase the efficiency of destruction of the shell to its complete separation from the core of rapeseed. The presented results make it possible to improve the quality of cleaning of rape seeds from the shell and improve the quality characteristics of the obtained oil, facilitate the subsequent technological processes of obtaining edible oil, reduce the cost of refining and deodorization by 2%.


Sign in / Sign up

Export Citation Format

Share Document